ZrH_2结构与热力学性质

基于密度泛函理论,采用全势线性缀加平面波加局域轨道方法和广义梯度近似研究了ZrH2的结构与弹性性质。结果表明:在基态条件下,ZrH2的晶格常数计算值与实验值及其它理论值相当吻合。在考虑声子作用的前提下,采用准谐德拜模型成功获得了不同条件下(0~50 GPa,0~1 300 K)ZrH2的热容、热膨胀系数和德拜温度等热力学性质。结果表明:定压热容预测值随温度升高而增大,并逐渐接近佩蒂特-杜隆极限;随压强增加,德拜温度呈增加趋势;随温度增加,德拜温度呈减小趋势;在压强一定的条件下,热膨胀系数随温度的升高而增大,且在高温高压条件下,热膨胀系数的增加趋势变缓。     

Zr4Al2高压下热动力学性质的第一性原理研究

本文主要通过平面波赝势密度泛函理论的第一性原理计算方法,采用了广义梯度近似（GGA）交换相关函数,研究了六角结构的Zr4Al2的EOS态方程和热动力学性质。通过采用了声子效应的准谐近似德拜模型,我们成功得到了晶胞体积V随温度以及V/V0、德拜温度Θ、热熔CV 随压强P的变化关系。另外,我们还研究了热膨胀系数α及格林参数γ随温度和压强的变化关系,计算结果表明格林参数和热膨胀系数随温度的升高而增加,但是在较高的温度下,热膨胀系数几乎不受温度的影响。     

高温高压下合金碳化物Fe3Mo3C热力学性质的第一性原理计算

基于平面波赝势密度泛函理论的第一性原理与准谐德拜模型结合的方法研究了高温高压下合金碳化物Fe₃Mo₃C的热力学性质.在压强范围为0～40 GPa和温度范围为0～1200 K的条件下,Fe₃Mo₃C的体积比V/V₀、体弹性模量B和德拜温度θ受压强的影响比温度更大.温度一定时,体弹性模量和德拜温度随压强的增大而迅速增大. Fe₃Mo₃C的热容C_v、熵S以及热膨胀系数α受温度的影响较压强更大.压强一定时,材料的热容、熵以及热膨胀系数均随温度升高单调增大,其中,热容和热膨胀系数随温度先快速上升后趋于平缓,最后热容接近于Dulong-Petit极限.     

高压下TiC的弹性、电子结构及热力学性质的第一性原理计算

利用基于密度泛函理论的第一性原理平面波赝势方法 并结合准谐徳拜模型研究了NaCl结构的TiC在高压下的弹性性质、电子结构和热力学性质. 计算所得零温零压下的晶格常数、体弹模量及弹性常数与实验值符合得很好. 零温下弹性常数和弹性模量随压强增大而增大. 通过态密度和电荷密度的分析, Ti-C键随压强增大而增强. 运用准谐德拜模型, 成功计算了TiC在高温高压下的体弹模量、熵、热膨胀系数、徳拜温度、 Grüneisen参数和比热容. 结果表明压强对体弹模量、热膨胀系数和徳拜温度的影响大于温度对其的影响. 热容随着压强升高而减小, 在高温高压下, 热容接近Dulong-Petit极限.     

高压下硫化钙的弹性和热力学性质的第一性原理计算

利用基于密度泛函理论的第一性原理平面波赝势方法结合准谐德拜模型研究NaCl结构的CaS在高压下的弹性和热力学性质.计算得到的零温零压下的晶格常数、体弹模量与实验值符合得很好.弹性常数和弹性模量随着压强的增大而增大.压强对体弹模量和热膨胀系数的影响大于温度的影响.热容随压强的升高而降低,在高温下热容接近于Dulong-Petit极限.通过求解Gibbs自由能计算得到B1结构和B2结构CaS的相变压为36.61 GPa.     

金红石结构TiO2结构和热力学性质的第一性原理研究

利用基于密度泛函理论的第一性原理计算方法以及准谐德拜模型研究了金红石TiO₂的结构和热力学性质.常温常压下所计算的晶格常数、体弹模量及其对压强的一阶导数与实验值和其他理论计算结果相符的较好.另外,我们还计算了体弹模量、热膨胀系数、热容与温度和压强的关系.     

金红石结构TiO2结构和热力学性质的第一性原理研究

利用基于密度泛函理论的第一性原理计算方法以及准谐德拜模型研究了金红石TiO2的结构和热力学性质。常温常压下所计算的晶格常数、体弹模量及其对压强的一阶导数与实验值和其他理论计算结果相符的较好。另外,我们还计算了体弹模量、热膨胀系数、热容与温度和压强的关系。     

金红石→萤石TiO2相变的第一性原理计算

利用第一性原理平面波密度泛函理论并结合准谐德拜模型,对TiO₂从金红石结构到萤石结构的相变进行理论研究.依据焓相等原理,得到TiO₂从金红石结构到萤石结构的相变压强为45.32 GPa,并通过吉布斯能的计算发现相变压强随温度的增加而增加,运用拟合的方法估计实验条件下的相变压强(温度为1900-2100K时,P_t=47.604~47.756 GPa).运用等吉布斯能原理,得到零压下从金红石到萤石结构TiO₂的相变温度为2029 K.计算结果与实验及其他理论值相符,并通过准谐德拜模型成功获得相变前后的结构和热力学性质,如相对体积、热膨胀系数、热容和德拜温度等.     

密度泛函理论研究高温高压下UO2弹性与热力学性能

采用第一性原理与准谐德拜模型研究UO2在高温高压条件下的弹性与热力学性能。UO2在高温高压下仍属离子型晶体,并且弹性性能计算表明,四角方向剪切常数在高温与高压下均保持稳定。高温下弹性常数C44没有明显变化,而高压下C44迅速增大。体积模量、剪切模量与杨氏模量均随压强增加而增大;高温条件下,体积模量、剪切模量与杨氏模量也未出现明显的降低,表明UO2在高温度高压下均可保持良好的力学性能。不同压强下,UO2定容热容均随温度迅速增大,并在1000 K 附近趋近于杜隆-佩蒂特极限。德拜温度则随温度降低,随压强升高。在低于室温条件下,热膨胀系数随温度急剧增加;温度继续增加,系数的增加趋势则逐渐变缓。计算结果还表明,UO2的热膨胀系数在相同条件下,远小于其他核材料。     

CeO2热力学性质的第一原理研究

使用第一性原理方法结合准谐德拜模型研究压力0~30 GPa,温度0~2 000 K,二氧化铈立方结构的热力学性质,包括常压下平衡体积V、体弹模量B₀、热容c_p和熵S随温度的变化以及不同压强下热容c_p、熵S、德拜温度Θ,体膨胀系数α与温度的关系.常压下计算的热容c_p和熵S随温度的变化与实验数据符合很好.     

Effect of Co doping on CIS2 thin films

In recent years, substantial scientific attention has been focused on renewable energy resources, which utilize natural resources for the production of electrical energy. Chalcopyrite semiconductors are used as one of the alternatives, Cu(In,Ga)Se₂ (CIGS) and CuInS₂ (CIS) are used for the fabrication of solar cells. These materials possess various properties Viz. ideal band gap (1.5?eV), high optical absorption, low light degradation, high radiation resistance, etc., hence they are suitable in the fabrication of solar cells. In contrast to other chalcopyrates, CuInS₂ is nontoxic, low-cost and easy to prepare by simple deposition techniques. Several impurities were doped to CuInS₂ bulks, to control conduction and also to obtain low resistivity. In this context, the structural, morphological and optical properties are reported for cobalt-doped CuInS₂ (CIS₂) thin films prepared by electro-deposition technique at room temperature. In the present study, we have used different cobalt concentration in the range of 0–5?wt.%. Doping of cobalt does not lead to the formation of any secondary phase, either in the form of metallic clusters or impurity complexes. However, with increase in cobalt concentration a decrease in the optical band gap, from 2.10 to 1.53?eV, is observed. In addition, implantation of cobalt in the CIS₂ gave changes in structural and surface properties of the thin films obtained. These thin films are also subjected to elemental analysis using EDAX.     

ZnS:Co2+和CdTe:Co2+中配体对g因子的贡献

采用双自旋-轨道耦合模型和分子轨道研究了Co²⁺离子在Ⅱ-Ⅵ半磁半导体ZnS和CdTe中的EPR g因子.计算表明,配体Te有大的SO耦合作用和强的共价性,其对g因子有较大的贡献.     

Co2YSn(Y=Ti,Zr)电子结构和轨道磁性的第一性原理研究

基于密度泛函理论(DFT)采用第一性原理的全势能线性缀加平面波(FLAPW)的能带计算方法研究了强磁性Heusler合金Co2TiSn和Co2ZrSn的电子能带结构,在计算中考虑了自旋-轨道藕合(SOC)的修正.计算结果表明两种合金在费米面附近的能带结构是一个d-d电子杂化作用形成的能带.分析计算结果发现Co原子对磁矩有主要的贡献,两种Heusler合金的磁矩是由于Co原子3d eg的自旋劈裂形成的,3deg的自旋向下分量是合金的电子态密度(DOS)的主要来源.由能带计算得到Co2TiSn和Co2ZrSn的自旋磁矩分别为1.97μB和1.96μB,其中Co原子在上述两种合金中的自旋磁矩分别是1.01μB和1.02μB,轨道磁矩分别为0.041μB和0.051μB.     

光谱、波谱法研究铜锌超氧歧化酶与氯化钴(Ⅱ)、组氨酸钴(Ⅱ)相互作用

我们首次发现的铜锌超氧歧化酶（Ｃｕ２Ｚｎ２ＳＯＤ）与氨基酸等发生直接相互作用的现象,是一种前人未研究过的重要的生化新现象［１］。在此新发现的基础上,本文用ＩＣＰ,ＶＩＳ,ＮＭＲ和酶活性测定等方法,又从不同角度拓展研究了Ｃｕ２Ｚｎ２ＳＯＤ酶与两类不同化合物,即无机氯化钴（ＣｏＣｌ２）、有机组氨酸钴（Ｃｏ（Ⅱ）（Ｈｉｓ）ｎ）的直接相互作用,发现酶活性中心金属离子同样与外加的这两类不同化合物发生相互作用,相应地影响了酶的催化活性。还发现Ｃｏ（Ⅱ）（Ｈｉｓ）ｎ比ＣｏＣｌ２与酶相互作用更强、更快,Ｃｏ（Ⅱ）（Ｈｉｓ）ｎ中的Ｃｏ（Ⅱ）更易进入酶中,更影响了酶的催化活性。     

(Nd1－xErx)2Co15.5V1.5的结构转变与磁性

利用电弧熔炼制备了(Nd1-xErx)2Co15.5V1.5（x=0—1.0）化合物样品.通过x射线衍射分析和磁性测量研究了Er替代Nd2Co15.5V1.5中的Nd时对化合物结构和磁性的影响.研究结果表明，低Er含量（x<0.4），化合物为Th2Zn17型结构；高Er含量时(x>0.)，化合物转变为Th2Ni17结构；Er含量为x＝0.4和0.5时，两种结构共存.两种结构的晶胞参数a,c和晶胞体积V随着Er含量的增加都呈现递减的趋势.随着Er含量的增加，(Nd1-xErx)2Co15.5V1.5化合物的 关键词： (Nd1-xErx)2Co15.5V1.5 结构转变 磁性     

Incommensurate-commensurate magnetic phase transition in double tungstate Li2Co(WO4)2

Magnetic susceptibility, specific heat, and neutron powder diffraction measurements have been performed on polycrystalline Li$_{2}$Co(WO$_{4}$)$_{2}$ samples. Under zero magnetic field, two successive magnetic transitions at $T_{\rm N1}\sim 9.4$ K and $T_{\rm N2}\sim 7.4$ K are observed. The magnetic ordering temperatures gradually decrease as the magnetic field increases. Neutron diffraction reveals that Li$_{2}$Co(WO$_{4}$)$_{2}$ enters an incommensurate magnetic state with a temperature dependent $\bm k$ between $T_{\rm N1}$ and $T_{\rm N2}$. The magnetic propagation vector locks-in to a commensurate value $\bm k = (1/2, 1/4, 1/4)$ below $T_{\rm N2}$. The antiferromagnetic structure is refined at 1.7 K with Co$^{2+}$ magnetic moment 2.8(1) $\mu_{\rm B}$, consistent with our first-principles calculations.     

Structural and magnetic properties of Pt in Co/Pt multilayers

[Co(30 Å)/Pt(x Å)]₂₀ multilayers with the Pt layer thicknesses varying from 5 Å to 20 Å were characterized structurally by high angle X-ray diffraction, X-ray reflectivity, X-ray absorption spectroscopy and magnetically by X-ray magnetic circular dichroism. It is found that the structure and magnetic properties of Pt have a strong correlation with the Pt layer thickness. The 20 Å thickness Pt layer is not almost influenced by the adjacent Co layer and the nearest neighbors are dominated by Pt-Pt shells. With decreasing Pt layer thickness, the nearest neighbors are gradually dominated by Pt-Co shells and the Pt-Co intermixing regions also remarkable increase at the interfaces, especially for the 5 Å thickness Pt layer. The orbital and spin magnetic moments as well as the ratio m_orb/m_spin all decrease systematically with increasing Pt layer thickness, indicating that the interface atoms are polarized by direct Pt-Co hybridization, but that the adjacent layers are polarized by Pt-Pt interactions.     

Optical and magneto-optical properties of Co/Pt multilayered films

Both experimental and computer-simulated magneto-optical (MO) and optical spectroscopies of Co/Pt multilayered films (MLF) with a nearly constant Pt sublayer thickness and variable Co sublayer thickness, as well as pure Co and Pt, and Co_0.51Pt_0.49 alloy films, have been performed in the energy range 1.1–4.7 eV. The simulations were achieved by solving the multireflection task for various models of the MLF. The comparison between experimental and computer-simulated optical properties of the Co/Pt MLF allowed us to evaluate the thickness of the interfacial regions with the alloyed components. The diagonal and off-diagonal components of the optical conductivity tensor were calculated not only for the pure Co and Co_0.51Pt_0.49 alloy films, and the whole Co/Pt MLF, but also for the spin-polarized Pt layers in the Co/Pt MLF.     

Co3O4纳米花的合成及其磁性

通过水热和热处理的方法，制备了产物Co3O4纳米花. 用X射线粉末衍射、场发射扫锚电镜、透射电镜和红外光谱等手段对产物进行了表征. 结果表明，产物纳米花是由大量的Co3O4纳米须组成，纳 米须的直径为20?40 nm，长度为100?500 nm，具有纳米孔结构，比表面积约为34.61 m2/g. 磁性测量表明，在零场冷却条件下，产物主要表现为反铁磁性；在加场冷却条件下，闭锁温度约为34K时，产物主要表现为铁磁性．     

High temperature thermoelectric properties of highly c-axis oriented Bi₂Sr₂Co₂O_y thin films fabricated by pulsed laser deposition

High-temperature thermoelectric transport property measurements have been performed on the highly c-axis oriented Bi2Sr2Co2Oy thin films prepared by pulsed laser deposition on LaAlO3(001).Both the electric resistivity ρ and the seebeck coefficient S of the film exhibit an increasing trend with the temperature from 300 K-1000 K and reach up to 4.8 m·Ω· cm and 202 μV/K at 980 K,resulting in a power factor of 0.85 mW/mK which are comparable to those of the single crystalline samples.A small polaron hopping conduction can be responsible for the conduction mechanism of the film at high temperature.The results demonstrate that the Bi2Sr2Co2Oy thin film has potential application in high temperature thin film thermoelectric devices.