声场中双空化泡的运动特性

空化泡的运动特性是声场作用下的动力学行为,受空化泡初始半径,声压幅值,驱动声压频率,液体特性等众多因素的影响,是个复杂工程。本文从双空化泡运动方程出发,考虑到液体粘滞系数、空化泡辐射阻尼项的影响,研究了不同初始半径、驱动声压频率、驱动声压幅值、液体粘滞系数下空化泡泡壁的运动情况,研究结果表明不同初始半径、外界驱动声压频率、驱动声压幅值、液体粘滞系数均会对空化泡的膨胀比和空化泡的溃灭时间有一定影响。     

超声对近壁微气泡溃灭过程的影响*

近壁微气泡溃灭特性的深入研究对靶向给药和基因治疗等技术具有较好的指导作用。该文基于数值模拟技术,采用有限体积法结合流体体积模型对超声作用下的近壁微气泡溃灭特性进行了研究,分析了超声对近壁微气泡溃灭动力学过程的影响。结果表明气泡溃灭最大射流速度与近壁距离无量纲参数在1.1~1.6范围内时成正比,与超声频率在10~60 Hz范围内时成正比,与气泡初始半径在50~100μm范围内时成反比;近壁气泡的二次溃灭最大射流速度大于一次溃灭,二次溃灭的作用更加明显。超声参数对近壁气泡溃灭过程存在较大影响,该研究为超声在医学上的应用提供了依据。     

高能超声制备碳纳米管增强AZ91D复合材料的声场模拟

建立了高能超声制备碳纳米管增强AZ91D复合材料的声场计算模型, 并采用有限元方法计算了20 kHz超声直接作用下AZ91D熔体的声场分布, 熔体声场呈辐射状分布, 距离声源越远, 声压幅值越低. 采用超声作用下单一气泡变化模型描述超声作用下AZ91D 熔体中的空化效应, 通过对Rayleigh-Plesset方程的求解, 得到了不同声压作用下气泡的变化规律, 获得了声压幅值与熔体空化效应的关系, 声压幅值越大, 气泡溃灭半径阈值越小, 熔体发生空化效应越容易. 计算了固定坩埚尺寸、不同超声探头没入熔体深度情况下的声场, 得到了超声探头最优没入深度为30 mm左右. 将声场计算结果以及AZ91D熔体中空化效应的发生规律进行综合分析, 得到了超声功率对有效空化区域的影响规律, 超声功率较大时, 有效空化区域体积随超声功率近似成线性增大. 最后, 通过甘油水溶液超声处理实验, 验证了模拟计算的准确性.     

超声清洗过程环境压力对声空化效应的影响*

在不同深度条件下的水下构建物超声清洗中,声空化是重要的源动力之一。为探明水下环境压力对声空化的影响,本文基于数值计算的方法,通过对超声波作用下气泡动力学的研究,讨论了环境压力对空化泡溃灭时的气泡最大半径、释放能量以及溃灭功率等因素的影响。结果表明：空化泡最大半径与环境压力在一定范围内呈近似线性关系;随着环境压力增大,空化泡释放能量和溃灭功率均显著减小,且两者在变化趋势和变化幅度上几乎一致;当环境压力大于声压幅值时,空化泡的最大半径、内部压强、内部温度与释放能量均远低于空化发生在环境压力小于声压幅值时的情形。     

超声振动珩磨作用下空化泡动力学及影响参数

为了合理利用超声振动珩磨作用下的空化效应,以磨削区单个空化泡为研究对象,考虑珩磨头合成扰动速度和珩磨压力的作用建立了磨削区空化泡的动力学模型。数值模拟了空化泡初始半径,珩磨压力,液体静压力和超声声压幅值对磨削区空化效应的影响。研究表明考虑超声振动珩磨作用时,空化泡膨胀的幅值会受到抑制,其溃灭时间也会缩短,而且较容易出现稳态空化。珩磨压力和液体静压力对磨削区空化主要起抑制作用,超声波声压幅值在一定范围内能够促进磨削区空化效果的提升。本文的研究为进一步理解超声振动珩磨的空化机理提供了理论支持。     

超声波声孔效应中气泡动力学的研究

在超声快速制取组织细胞病理切片的过程中，发现激励信号对切片制取效果有明显的影响.为了掌握超声激励信号对组织细胞的影响规律，达到快速制取病理切片的最佳状态，从气泡空化模型入手，通过改变激励信号频率、声压、气泡初始半径和液体黏滞系数等参量，研究了声孔效应中气泡动力学激励机制.数值计算表明：空化泡振动随激励声压增强而升高，随液体黏滞系数增强而减弱；一定频率范围内空化泡振动能保持在膨胀、收缩和振荡的稳定空化状态，存在空化泡稳态振动的最佳激励频率；一定初始半径能保证空化泡产生稳定的振动，存在空化泡稳态振动幅度最大的初始半径.实际操作中，在频率、声压、初始半径和黏滞系数综合作用的若干空化阈内，声孔效应使超声快速法制取细胞组织切片获得最佳效果. 关键词： 声孔效应 超声空化 气泡振动 稳态空化域     

低频超声空化场中柱状泡群内气泡的声响应

本文在气泡群振动模型的基础上,考虑气泡间耦合振动的影响,得到了均匀柱状泡群内振动气泡的动力学方程,以此为基础分析了低频超声空化场中柱形气泡聚集区内气泡的非线性声响应特征.气泡间的耦合振动增加了系统对每个气泡的约束,降低了气泡的自然频率,增强了气泡的非线性声响应.随着气泡数密度的增加,气泡的自然共振频率降低,受迫振动气泡受到的抑制增强.数值分析结果表明:1)驱动声波频率越低,气泡的初始半径越小,气泡数密度变化对气泡最大半径变化幅度的影响越大;2)气泡振动幅值响应存在不稳定区,不稳定区域分布与气泡初始半径、驱动声波压力幅值、驱动声波频率等因素有关.在低频超声波作用下,对初始半径处在1—10μm之间的空化气泡而言,气泡初始半径越小,气泡最大半径不稳定区分布范围越大,表明小气泡具有更强的非线性特征.因此,气泡初始半径越小,声环境变化对空化泡声响应稳定性影响越显著.     

声驻波场中空化泡的动力学特性

以水为工作介质, 考虑了液体的可压缩性, 研究了驻波声场中空化泡的运动特性, 模拟了驻波场中各位置处空化泡的运动状态以及相关参数对各位置处空化泡在主Bjerknes力作用下运动方向的影响. 结果表明: 驻波声场中, 空化泡的运动状态分为三个区域, 即在声压波腹附近空化泡做稳态空化, 在偏离波腹处空化泡做瞬态空化, 在声压波节附近, 空化泡在主Bjerknes 力作用下, 一直向声压波节处移动, 显示不发生空化现象; 驻波场中声压幅值增加有利于空化的发生, 但声压幅值增加到一定上限时, 压力波腹区域将排斥空化泡, 并驱赶空化泡向压力波节移动, 不利于空化现象的发生; 当声频率小于初始空化泡的共振频率时, 声频率越高, 由于主Bjerknes 力的作用将有更多的空化泡向声压波节移动, 不利于空化的发生, 尤其是驻波场液面的高度不应是声波波长的1/4; 当声频率一定时, 空化泡初始半径越大越有利于空化现象的发生, 但当空化泡的初始半径超过声频率的共振半径时, 由于主Bjerknes力的作用将有更多的空化泡向声压波节移动, 不利于空化的发生.     

声场作用下两空化泡相互作用的研究

建立了声场作用下两空化泡泡壁的运动方程,得出了双空化泡的共振频率,振动半径及空化噪声声压．由频率方程,振动半径和声压方程可以看出两气泡的运动情况与单气泡的运动情况有着明显的不同．共振频率,共振振幅及声压与两气泡之间的间距有关．在一定的简化条件下,运用MATLAB语言对共振频率,共振振幅及空化噪声声压进行了数值求解,发现共振频率和共振振幅随空泡间距的增大而增大,空化噪声声压随距离增大先增大后减小． 关键词： 超声 空化 频率 声压     

含气量对激光空泡在刚性壁面空蚀的影响

采用强脉冲激光器设计液体环境下刚性壁面空蚀实验平台,改变液体中含气量,利用高速相机观察不同含气量条件下激光空泡在壁面附近的脉动过程,并对刚性壁面造成的空蚀结果进行了观测。实验研究发现,随着液体中相对空气含量的提高,激光空泡脉动的最大尺寸增大,空泡的膨胀运动变剧烈,溃灭运动速度降低,空泡的溃灭强度降低,从而影响到溃灭冲击波和壁面微射流对刚性壁面的冲击速度,减弱了壁面空蚀,而液体中含气量的提高能够降低激光空泡对刚性壁面的空蚀程度。     

Effects of surface tension on the dynamics of a single micro bubble near a rigid wall in an ultrasonic field

Acoustic cavitation is a very important hydrodynamic phenomenon, and is often implicated in a myriad of industrial, medical, and daily living applications. In these applications, the effect mechanism of liquid surface tension on improving the efficiency of acoustic cavitation is a crucial concern for researchers. In this study, the effects of liquid surface tension on the dynamics of an ultrasonic driven bubble near a rigid wall, which could be the main mechanism of efficiency improvement in the applications of acoustic cavitation, were investigated at the microscale level. A synchronous high-speed microscopic imaging method was used to clearly record the temporary evolution of single acoustic cavitation bubble in the liquids with different surface tension. Meanwhile, the bubble dynamic characteristics, such as the position and time of bubble collapse, the size and stability of the bubbles, the speed of bubble boundaries and the micro-jets, were analyzed and compared. In the case of the single bubbles near a rigid wall, it was found that low surface tension reduces the stability of the bubbles in the liquid medium. Meanwhile, the bubbles collapse earlier and farther from the rigid wall in the liquids with lower surface tension. In addition, the surface tension has no significant influence on the speed of the first micro-jet, but it can substantially increase the speed of second and the third micro-jets after the first collapse of the bubble. These effects of liquid surface tension on the bubble dynamics can explain the mechanism of surfactants in numerous fields of acoustic cavitation for facilitating its optimization and application.     

Numerical study on the desorption processes of oil droplets inside oil-contaminated sand under cavitation micro-jets

The removal of the adsorbed oil droplet is critical to deoiling treatment of oil-bearing solid waste. Ultrasonic cavitation is regarded as an extremely useful method to assist the oil droplets desorption in the deoiling treatment. In this paper, the effects of cavitation micro-jets on the oil droplets desorption were studied. The adsorbed states of oil droplets in the oil-contaminated sand were investigated using a microscope. Three representative absorbed states of the oil droplets can be summarized as: (1) the individual oil droplet adsorbed on the particle surface (2) the clustered oil droplets adsorbed on the particle surface; (3) the oil droplet adsorbed in a gap between particles. The micro-jet generation during the bubble collapse near a rigid wall under different acoustic pressure amplitudes at an ultrasonic frequency of 20 kHz was investigated numerically. The desorption processes of the oil droplets at the three representative absorbed states under micro-jets were also simulated subsequently. The results showed that the acoustic pressure has a great influence on the velocity of micro-jet, and the initial diameter of cavitation bubbles is significant for the cross-sectional area of micro-jets. The wall jet caused by a micro-jet impacting on the solid wall is the most important factor for the removal of the absorbed oil droplets. The oil droplet is broken by the jet impinging, and then it breaks away from the solid wall due to the shear force generated by the wall jet. In addition to a higher sound pressure, the cavitation bubble at a larger initial diameter is more important for the desorption of the clustered oil droplets. Conversely, the micro-jet generated by the cavitation bubble at a smaller initial diameter (0.1 mm) is more appropriate for the desorption of the oil droplet in a narrow or sharp-angled gap.     

An equivalent method of jet impact loading from collapsing near-wall acoustic bubbles: A preliminary study

Cavitation damage is a micro, high-speed, multi-phase complex phenomenon caused by the near-wall bubble group collapse. The current numerical simulation method of cavitation mainly focuses on the collapse impact of a single cavitation bubble. The large-scale simulation of the cavitation bubble group collapse is difficult to perform and has not been studied, to the best of our knowledge. In this study, the equivalent model of impact loading of acoustic bubble collapse micro-jets is proposed to study the cavitation erosion damage of materials. Based on the theory of the micro-jet and the water hammer effect of the liquid–solid impact, an equivalent model of impact loading of a single acoustic bubble collapse micro-jet is established under the principle of deformation equivalence. Since the acoustic bubbles can be considered uniformly distributed in a small enough area, an equivalent model of impact loading of multiple acoustic bubble collapse micro-jets in a micro-segment can be derived based on the equivalent results of impact loading of a single acoustic bubble collapse micro-jet. In fact, the equivalent methods of cavitation damage loading for single and multiple near-wall acoustic bubble collapse micro-jets are formed. The verification results show the law of cavitation deformation of concrete using equivalent loading is consistent with that of a micro-jet simulation, and the average relative errors and the mean square errors are insignificant. The equivalent method of impact loading proposed in this paper has high accuracy and can greatly improve the calculation efficiency, which provides technical support for numerical simulation of concrete cavitation.     

Analysis of the effect of impact of near-wall acoustic bubble collapse micro-jet on Al 1060

The bubble collapse near a wall will generate strong micro-jet in a liquid environment under ultrasonic field. To explore the effect of the impact of near-wall acoustic bubble collapse micro-jet on an aluminum 1060 sheet, the cavitation threshold formula and micro-jet velocity formula were first proposed. Then the Johnson-Cook rate correlation material constitutive model was considered, and a three-dimensional fluid-solid coupling model of micro-jet impact on a wall was established and analyzed. Finally, to validate the model, ultrasonic cavitation test and inversion analysis based on the theory of spherical indentation test were conducted. The results show that cavitation occurs significantly in the liquid under ultrasonic field, as the applied ultrasonic pressure amplitude is much larger than liquid cavitation threshold. Micro pits appear on the material surface under the impact of micro-jet. Pit depth is determined by both micro-jet velocity and micro-jet diameter, and increases with their increase. Pit diameter is mainly related to the micro-jet diameter and d_p/d_j ≈ 0.95–1.2, while pit’s diameter-to-depth ratio is mainly negatively correlated with the micro-jet velocity. Wall pressure distribution is mostly symmetric and its maximum appears on the edge of micro-jet impingement. Obviously, the greater the micro-jet velocity is, the greater the wall pressure is. Micro pits formed after the impact of micro-jet on aluminum 1060 surface were assessed by ultrasonic cavitation test. Inversion analysis results indicate that equivalent stress, equivalent strain of the pit and impact strength, and velocity of the micro-jet are closely related with pit’s diameter-to-depth ratio. For the pit’s diameter-to-depth ratio of 16–68, the corresponding micro-jet velocity calculated is 310–370 m/s.     

Nonlinear dynamics of a cavitation bubble pair near a rigid boundary in a standing ultrasonic wave field

The dynamics of a micrometer-sized bubble pair in water near a rigid boundary under standing ultrasonic wave excitation is investigated in this study. The viscous effect in the boundary layer at the air-water interface is considered following the viscous correction model. The evolution of the bubble surface at the collapsing stage of the bubble pair is presented for different parameter sets. The field pressure near the rigid boundary, which is induced by the oscillating bubble pair, and the high-speed water jet at the collapse stage, form the main focus of the analysis. This reveals that a horizontal configuration of the bubble pair retards the strength of the bubble jet towards the boundary, whilst a vertical configuration, especially with differently-sized bubbles, can enhance the bubble collapse. This study may help to understand the interaction of multiple bubbles in an acoustic field and its application to surface cleaning.     

Thermodynamic of collapsing cavitation bubble investigated by pseudopotential and thermal MRT-LBM

The thermodynamic of cavitation bubble collapsing is a complex fundamental issue for cavitation application and prevention. The pseudopotential and thermal multi-relaxation-time lattice Boltzmann method (MRT-LBM) is adopted to investigate the thermodynamic of collapsing cavitation bubble in this paper. The simulation results satisfy the maximum temperature equation of the bubble collapse, which derived from the Rayleigh-Plesset (R-P) equation. The validity of thermal MRT-LBM in simulating the collapse process of cavitation bubble is verified. It shows that the temperature evolution of vapor-liquid phase is well captured. Furthermore, the two-dimensional (2D) temperature, velocity and pressure field of the bubble near a solid wall are analyzed. The maximum temperature inside the bubble and wall temperature under different position offset parameters are discussed in details.     

Experimental investigation on the effects of the standoff distance and the initial radius on the dynamics of a single bubble near a rigid wall in an ultrasonic field

Bubble behaviors near a boundary in an ultrasonic field are the fundamental forms of acoustic cavitation and of substantial importance in various applications, such as industry cleaning, chemical engineering and food processing. The effects of two important factors that strongly affect the dynamics of a single acoustic cavitation bubble, namely, the initial bubble radius and the standoff distance, were investigated in this work. The temporal evolution of the bubble was recorded using high speed microphotography. Meanwhile, the time of bubble collapse and the characteristics of the liquid jets were analyzed. The results demonstrate that the intensity of the acoustic cavitation, which is characterized by the time of bubble collapse and the liquid jet speed, reaches the optimum level under suitable values of the initial bubble radius and the normalized standoff distance. As the initial bubble radius and the normalized standoff distance increase or decrease from the optimal values, the time of the bubble collapse increases, and the first liquid jet’s speed decreases substantially, whereas the speeds of the second and third liquid jets exhibit no substantial changes. These results on bubble dynamics in an ultrasonic field are important for identifying or correcting the mechanisms of acoustic cavitation and for facilitating its optimization and application.     

近复杂几何固壁空泡溃灭的伪势格子Boltzmann建模*

格子Boltzmann方法伪势多相模型具有高效性和复杂几何边界实施的简易性。该文采用改进作用力的伪势多相模型,通过优化参数实现最大程度的热力学一致性,进而提高模型的密度比和稳定性。分别从伪速度、网格不变性、Young-Laplace验证等方面研究了改进模型的性能。通过改进的模型模拟了复杂几何固壁附近空泡溃灭过程。分析了空化泡溃灭阶段的密度场、压力场和速度场演化过程,以及复杂几何固壁附近的空泡动力学特性。结果表明伪势格子Boltzmann方法在探索空泡溃灭和复杂几何固壁间的相互作用规律研究中是一种有效的工具。     

曲面固壁附近空化泡溃灭动力学的 流体体积数值研究*

流体体积法(VOF)可以便捷、高效地实现对多相流界面的捕捉和追踪。本文基于VOF方法,对单个空化泡在曲面固壁附近的运动进行了数值模拟,从实验对比、压力场、速度场、温度场演化、溃灭时间、射流速度、固壁温度等方面分析了空化泡溃灭过程的热动力学影响。结果表明,数值模拟得到的空化泡形态演化与实验观测到的现象一致,随着位置参数、泡内外压差及曲面固壁尺寸的改变,空化泡热动力学行为也将发生变化,受到流体运动及射流冲击的影响,溃灭瞬间产生的高温高压使得曲面固壁温度升高。本文研究的曲面固壁附近空化泡溃灭效应,揭示了空化泡与曲面固壁间的相互作用规律,对学术研究及工程应用都具有重要意义。