α稳定噪声环境下多频微弱信号检测的参数诱导随机共振现象

本文将α稳定噪声与双稳随机共振系统相结合, 研究了不同α稳定噪声环境下高低频(均为多频)微弱信号检测的参数诱导随机共振现象, 探究了α稳定噪声的特征指数α(0 < α ≤ 2)和对称参数β (-1≤ β ≤ 1)及随机共振系统参数a, b对共振输出效应的作用规律. 研究结果表明, 在不同分布的α稳定噪声环境下, 通过调节系统参数a和b均可诱导随机共振来实现多个高、低频微弱信号的检测, 且存在多个a, b参数区间均可诱导随机共振, 这些区间不随α或β的变化而变化; 在高、低频微弱信号检测中, α或β对随机共振输出效应的作用规律相同. 本研究结果将有助于α稳定噪声环境下参数诱导随机共振现象中系统参数的合理选取, 进而可为实现基于随机共振的多频微弱信号检测方法的工程应用奠定基础. 关键词： 随机共振 α稳定噪声')" href="#">α稳定噪声 多频微弱信号检测 平均信噪比增益     

α稳定噪声驱动的非对称双稳随机共振现象

以微弱周期信号激励的非对称双稳系统为模型,以信噪比增益为指标,首先针对加性和乘性α稳定噪声共同作用的随机共振现象展开了研究,然后针对单独加性α稳定噪声激励的随机共振现象进行了研究,探究了α稳定噪声特征指数α和对称参数β分别取不同值时,系统结构参数a,b,刻画双稳系统非对称性的偏度r以及α稳定噪声强度放大系数Q或D对非对称双稳系统共振输出的作用规律.研究结果表明,无论在加性和乘性α稳定噪声共同作用下还是在单独加性α稳定噪声作用下,通过调节a和b或者r均可诱导随机共振,实现微弱信号的检测,且有多个参数区间与之对应,这些区间不随α或β的变化而变化;在研究噪声诱导的随机共振现象时发现,调节噪声强度放大系数也可使系统产生随机共振现象,且达到共振状态时D的区间也不随α或β的变化而变化.这些结论为α稳定噪声环境下参数诱导随机共振中系统参数以及噪声诱导随机共振中噪声强度的合理选取提供了依据.     

乘性和加性α稳定噪声环境下的过阻尼单稳随机共振现象

本文将α稳定噪声与单稳随机共振系统相结合,研究了乘性和加性α稳定噪声环境下的过阻尼单稳随机共振现象,探究了α稳定噪声特征指数α(0α2)、对称参数β(-1β1),单稳系统参数a及乘性α稳定噪声放大系数D对共振输出效应的作用规律.研究结果表明,在不同分布的α稳定噪声环境下,在一定范围内通过调节a或D均可诱导随机共振来实现单个或多个高、低频微弱信号的检测,且a和D分别存在一个最优值可使系统产生最佳的随机共振效应;不同α或β均可对系统共振输出效应产生规律性的影响,且α或β在高、低频微弱信号检测中的作用规律相同;在研究α稳定噪声环境下单、多频单稳随机共振现象时所得结论是相同的.本研究结果可为实现α稳定噪声环境下单稳随机共振系统参数的自适应调节奠定基础.     

α稳定噪声驱动的非对称双稳随机共振现象

以微弱周期信号激励的非对称双稳系统为模型, 以信噪比增益为指标, 首先针对加性和乘性α 稳定噪声共同作用的随机共振现象展开了研究, 然后针对单独加性α 稳定噪声激励的随机共振现象进行了研究, 探究了α 稳定噪声特征指数α 和对称参数β 分别取不同值时, 系统结构参数a, b, 刻画双稳系统非对称性的偏度r以及α 稳定噪声强度放大系数Q或D对非对称双稳系统共振输出的作用规律. 研究结果表明, 无论在加性和乘性α 稳定噪声共同作用下还是在单独加性α 稳定噪声作用下, 通过调节a和b或者r均可诱导随机共振, 实现微弱信号的检测, 且有多个参数区间与之对应, 这些区间不随α 或β 的变化而变化; 在研究噪声诱导的随机共振现象时发现, 调节噪声强度放大系数也可使系统产生随机共振现象, 且达到共振状态时D的区间也不随α 或β 的变化而变化. 这些结论为α 稳定噪声环境下参数诱导随机共振中系统参数以及噪声诱导随机共振中噪声强度的合理选取提供了依据.     

幂函数型单势阱随机振动系统的广义随机共振

将线性随机振动系统中通常的简谐势阱推广为更一般的幂函数型势阱,得到幂函数型单势阱非线性随机振动系统.利用随机情形下的二阶Runge-Kutta算法研究了噪声强度、势阱参数和周期激励参数对系统稳态响应的一阶矩振幅和系统响应的稳态方差的影响.对决定势阱形状的势阱参数之一b历经b2,b2以及相当于简谐势阱的b=2等全部情况的研究表明:随噪声强度D的变化,系统稳态响应的一阶矩振幅可以在b2时出现非单调变化,即发生广义随机共振现象,而对通常的b=2简谐势阱以及b2的情况,则无该现象发生;随势阱参数的变化,系统稳态响应的一阶矩振幅以及系统响应的稳态方差也可以发生非单调变化.     

非高斯噪声激励下FitzHugh-Nagumo神经元系统的随机共振

研究了乘性非高斯噪声和加性高斯白噪声共同激励下FitzHugh-Nagumo(FHN) 神经元系统的随机共振问题. 利用路径积分法和两态模型理论, 推导出系统信噪比的表达式. 研究结果表明: 系统参数在不同的取值条件下, FHN神经元模型出现了随机共振和双重随机共振现象. 此外, 非高斯参数q在不同的取值条件下, 乘性噪声强度和加性噪声强度对信噪比的影响是不同的. 非高斯噪声的加入有利于增强FHN神经元系统的信号响应.     

α稳定噪声下一类周期势系统的振动共振

将多个低频微弱信号、高频信号和加性α稳定噪声共同激励的一类周期势系统作为研究模型,以平均信噪比增益(MSNRI)为性能指标,对α稳定噪声环境下周期势系统中的振动共振现象进行了研究,分别探究了α稳定噪声的特征参数α、对称参数β、加性噪声强度放大系数D、高频信号幅值B以及频率?对振动共振输出效应的影响.研究结果表明:1)在不同分布的α稳定噪声环境下,固定频率?(或幅值B),当幅值B(或频率?)逐渐增大时,MSNRI-B(或MSNRI-?)曲线出现多个峰值,即存在多个B区间(或?区间)可诱导振动共振,并且这些区间不会随噪声分布参数α或β的变化而变化;2)当加性噪声强度放大系数D发生变化时,幅值B和频率?的共振区间没有随着D的变化而变化,表明只有高频信号能量向待测低频信号转移,噪声能量并没有向待测低频信号转移.另外当幅值B、频率?固定时,随着D的逐渐增大,依然可以实现微弱信号的检测,表明振动共振可以克服工业现场噪声强度不可调控的缺点.本文研究结果提供了一种新的微弱信号检测方法,在信号处理领域有着潜在的应用价值.     

一类线性阻尼振子的随机共振研究

针对随机有色噪声参数激励和周期调制噪声外激励联合作用下的线性阻尼振子,利用Shapiro-Loginov公式推导了系统响应的一、二阶稳态矩的解析表达式.发现这类系统存在传统的随机共振、广义的随机共振和“真正”的随机共振;当乘性噪声强度和调制噪声强度的比值大于等于1时,系统出现随机多共振现象.通过数值计算的系统响应功率谱,验证了理论分析结果. 关键词： 随机共振 周期调制的噪声 线性阻尼振子     

单模非线性光学系统的弛豫速率与随机共振

应用变分法研究了一个单模非线性光学系统的弛豫速率对噪声强度的依赖性，并由线性响应理论考察了该系统的随机共振行为.研究结果表明当系统没有偏置时，单稳与多稳情形下的松弛速率对噪声强度的依赖性表现出很大的不同.揭示了对称的一维单稳系统中的随机共振现象，并针对一维单稳系统中随机共振存在的一般条件进行了分析. 关键词： 弛豫速率 随机共振 变分法 线性响应理论     

α稳定噪声环境下过阻尼系统中的参数诱导随机共振现象

本文采用随机模拟方法, 研究了过阻尼振子系统在α稳定噪声环境下的参数诱导随机共振现象. 结果表明, 在α噪声环境下, 调节系统参数能够诱导随机共振现象; 而且调节非线性项参数时, 随机共振效果随α稳定噪声的指数的减小而减弱, 但当调节线性项参数时, 随机共振效果则随着α稳定噪声的特征指数的减小而增强. 本文的结论在α稳定噪声环境下, 利用参数诱导随机共振原理进行弱信号检测方面具有重要的理论意义, 并有助于理解不同α稳定噪声对一般随机共振系统的共振效果的影响.     

Analysis of weak signal detection based on tri-stable system under Levy noise

Stochastic resonance system is an effective method to extract weak signal.However,system output is directly influenced by system parameters.Aiming at this,the Levy noise is combined with a tri-stable stochastic resonance system.The average signal-to-noise ratio gain is regarded as an index to measure the stochastic resonance phenomenon.The characteristics of tri-stable stochastic resonance under Levy noise is analyzed in depth.First,the method of generating Levy noise,the effect of tri-stable system parameters on the potential function and corresponding potential force are presented in detail.Then,the effects of tri-stable system parameters w,a,b,and Levy noise intensity amplification factor D on the resonant output can be explored with different Levy noises.Finally,the tri-stable stochastic resonance system is applied to the bearing fault detection.Simulation results show that the stochastic resonance phenomenon can be induced by tuning the system parameters w,a,and b under different distributions of Levy noise,then the weak signal can be detected.The parameter intervals which can induce stochastic resonances are approximately equal.Moreover,by adjusting the intensity amplification factor D of Levy noise,the stochastic resonances can happen similarly.In bearing fault detection,the detection effect of the tri-stable stochastic resonance system is superior to the bistable stochastic resonance system.     

Stochastic resonance characteristic analysis of new potential function under Levy noise and bearing fault detection

Based on the output saturation of classcial bistable stochastic resonance (CBSR), a new type of piecewise nonlinear bistable stochastic resonance (PNBSR) system is constructed. The mean signal-to-noise ratio gain is regarded as an index to measure the stochastic resonance phenomenon. The laws for the resonant output of piecewise nonlinear bistable system governed by l, c, a, b and D of Levy noise are explored under different characteristic index α and symmetry parameter β of Levy noise. The results show that the output of PNBSR system has increased 4?dB by comparing with the output signal-to-noise ratio of CBSR system. And the stochastic resonance phenomenon can be induced by adjusting the piecewise nonlinear system's parameters under any α or β of Levy noise. The interval of the parameters of system which induces good stochastic resonance is roughly the same. And the output signal waveform of resonance is very similar to the input signal waveform, which has some reference value for the signal recovery. Moreover, we can find the good stochastic resonance interval of the system parameters do not change with D of Levy noise under the different noise intensity D of Levy noise. On the basis of this, adjusting the intensity amplification factor D of Levy noise, which induces good stochastic resonance, and the interval does not change with α or β. At last, the piecewise nonlinear bistable system is applied to detect bearing fault signals, which achieves better performance compared with the classical bistable system.     

Stochastic resonance in a single-well system with exponential potential driven by Levy noise

Noise and potential function are vital to stochastic resonance (SR). This paper attempts to broaden the research of the SR and explore a better potential function. Based on the absolute and exponential potentials, a generalized exponential type single-well potential function is constructed. Then the characteristics of the corresponding exponential type single-well SR (ESR) system driven by Levy noise is analyzed numerically. Firstly, the effects of the characteristic index α, symmetric parameter β and noise intensity D of Levy noise on the input signal to noise ratio (SNRi) are investigated. Then, the effects of system parameters a, b, r and noise intensity D on the resonant output is explored. Finally, the ESR system is applied to the fault characteristic extraction of rolling element bearings. The simulation results show that the SR phenomenon is able to be excited by tuning the parameters a, b, r and D under different values of α and β. The larger b (or a) widens the parameter interval of a (or b) which can induce SR. The ESR system is able to solve the problem that the traditional systems fail to achieve SR due to the improper selection of parameters. In bearing fault detection, the detection effect of the ESR system is superior to the bistable SR system.     

Stochastic resonance and antiresonance in monostable systems

We study characteristics of the output signal in a nonlinear monostable inertial dynamical system with the harmonic signal and Gaussian white noise supplied additively to the input. Several types of monostable systems are examined, and analytical expressions for the output-signal power amplification and signal-to-noise ratio are obtained for such systems for the first time. The main attention is paid to the stochastic resonance and antiresonance phenomena, which manifest themselves as nonmonotonic dependences of the mentioned characteristics on the input-noise intensity. In particular, it is shown for the first time that the output signal-to-noise ratio may have a maximum as a function of the input-noise intensity in a monostable system. This corresponds to the classical definition of stochastic resonance, which earlier was only observed in bistable (multistable) systems. Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Radiofizika, Vol. 51, No. 10, pp. 899–913, October 2008.     

Stochastic resonance of a tri-stable system with α stable noise

A tri-stable system excited by weak periodic signal is taken as a model and the stochastic resonance phenomenon is investigated by additive α stable noise in this paper. The laws for the resonance system parameters q, p, skewness parameter r and intensity amplification factor Q of α stable noise to act on the resonant output are explored under different stability indicies α and asymmetric skewness β of α stable noise. The results indicate that a weak signal can be realized by tuning the system parameters q, p and r under the joint action of additive α stable noise, and the interval of q and p which can induce stochastic resonance does not change with α or β. Moreover, a certain rule is found in which adjusting the intensity amplification factor Q of α stable noise can also realize a synergistic effect when studying the noise-induced stochastic resonance, and the interval of Q does not change with α or β; the best value of the characteristic index is $\alpha =1$ under any system parameter, and the best value of the symmetry parameter is $\beta =1$ under any system parameter. So, the system performance is best when $\alpha =1$ and $\beta =1$. The results will contribute to a reasonable selection of parameter-induced stochastic resonance system parameters and noise intensity of noise-induced stochastic resonance under α stable noise.