激光诱导植物叶绿素荧光寿命及光谱特性分析

传统荧光光谱分析法虽能用于评估植物生理状况,但在植物遥感探测中该方法具有抗干扰性弱、待测数据量大的缺陷.针对此问题,提出一种荧光寿命成像技术,将植物荧光寿命及光谱信息结合,分析植物内在生理信息,实现了远距离、大范围精确测量植物生理状况.采用时间分辨测量法,用连续激光脉冲照射植物产生大量相同的荧光信号,同时不断改变探测器的启动延迟时间,得到完整的荧光信号,用解卷积法反演植物荧光寿命.对活体法国冬青植株的光谱信息与荧光寿命特性进行了研究,结果显示植物荧光寿命与叶绿素含量成线性关系,并且植物叶绿素含量在0.03~0.06 mg/cm~2这一特定范围,线性相关系数高达0.9051,比荧光光谱能更精确地反映植物叶绿素含量.     

激光诱导叶绿素荧光寿命的测量及其特性分析

提出了一种用于评估植物生长状况及环境监测的激光诱导叶绿素荧光寿命测量方法. 采用波长355 nm的激光作为光源激发叶绿素荧光, 由光电倍增管接收其荧光信号, 由于被测叶绿素荧光衰减函数与激光脉冲、仪器响应函数卷积在一起, 根据它们的特性, 运用时间分辨测量法分别测得叶绿素荧光及其背景信号, 并结合一种新型解卷积算法可分离出真实的叶绿素荧光衰减函数, 从而获取叶绿素的荧光寿命. 测试结果表明: 该方法能够实现叶绿素荧光寿命的高精度实时监测, 对不同叶绿素含量的溶液荧光寿命进行了测试, 证明叶绿素含量与其荧光寿命具有相关性, 并且拟合了叶绿素含量与荧光寿命的标定曲线. 关键词： 荧光寿命 激光诱导荧光 时间分辨测量法 叶绿素含量     

激光诱导植物荧光寿命校正技术及其特性分析

激光诱导植物荧光寿命测量法是在植物荧光光谱分析法基础上开发的一种评估植物生长状况及环境监测的新技术。根据植物叶绿素荧光信号的物理特性,利用信息仿真技术开发了一种叶绿素荧光寿命校正方法,可提高植物叶绿素荧光寿命的测量精度。利用激光诱导叶绿素荧光寿命测量系统分别测得叶绿素荧光及其背景信号,先用解卷积法叶绿素荧光信号中分离出荧光衰减函数,可获取荧光寿命估计值。再结合叶绿素荧光寿命校正技术就能反演得到高精度的植物荧光寿命。仿真与实验结果表明：该方法可实现高精度的植物荧光寿命实时监测;并对不同含量的叶绿素提取液进行了测试,构建了植物荧光寿命与叶绿素含量的对应关系模型。未来该技术可用于遥感监测海洋、湖泊、河流中藻类植物的生物含量。     

单光子调制频谱用于量子点荧光寿命动力学的研究

本文开展了基于单光子调制频谱测量量子点荧光寿命动力学特性的研究.在脉冲激光激发下,对探测到的量子点单光子荧光信号进行频谱分析以获得荧光调制频谱,研究发现特征频谱信号幅值与荧光寿命之间存在确定的非线性对应关系.这种单光子调制频谱方法能有效消除背景噪声和单光子探测器暗计数的影响,用于分析量子点荧光寿命动力学特性时在准确度以及时间分辨率方面都较目前普遍采用的荧光衰减曲线寿命拟合方法呈现出明显优势:当涨落误差为5%时,寿命测量准确度提高了一个数量级;当涨落误差和偏离误差均为5%时,对动力学测量效率以及时间分辨率提高了四倍以上.因此单光子调制频谱可以作为获取量子点在短时间尺度内激发态动力学信息的一种有效技术手段.     

饱和激发下叶绿素荧光非线性变化及影响分析

叶绿素浓度是海洋初级生产力的重要指标之一,激光诱导荧光技术可以实现海水叶绿素浓度的快速测量。测量叶绿素浓度的传统激光诱导荧光原理,是利用叶绿素荧光与水体Raman散射的强度比值（I_F/R）进行反演,即叶绿素浓度n_chl＝CI_F/R,其中C为系统常量。这是依据叶绿素荧光685 nm、水体Raman散射强度都与激发光强呈线性关系。然而,该理论并没有考虑诱导荧光饱和现象的存在。当诱导激光强度达到一定程度后,685 nm荧光强度随激发光强非线性变化。另外,值得注意的是,水体Raman散射并不存在信号饱和现象。为了探讨饱和激发造成荧光非线性变化的影响,在激光诱导荧光技术测量叶绿素浓度的实验中,设计两种测量方案,即：不同激光功率诱导单一浓度样本的荧光测量,和固定激光功率时不同浓度样本的荧光测量。实验中利用Nd∶YAG三倍频激光355 nm激发获得叶绿素溶液的404 nm处 Raman散射和685 nm荧光。实验结果分为2部分进行讨论：（1）为了分析饱和激发造成荧光变化的非线性特性,通过调节激发光功率测量溶液的受激发射光谱,发现水体Raman散射强度与激发光强呈线性关系,而685 nm荧光强度出现饱和激发下的非线性变化。而且,随叶绿素浓度的增加,685 nm荧光的非线性趋势更为明显,Raman散射强度与激发光强的线性关系中斜率变小。数据分析表明,685 nm荧光数据拟合的4阶多项式和Raman散射效率值,可以定性地表征685 nm荧光的饱和程度。（2）考虑实际海洋激光雷达探测叶绿素浓度应用中存在饱和激发荧光非线性现象,为了分析荧光非线性对传统叶绿素浓度反演理论适用性的影响,在固定激发光强情况下对不同浓度叶绿素溶液的发射光谱进行测量。将激发光功率调节至52.00,80.70,132.10和197.30 mW·cm-2,获取相应激发光强下685 nm荧光与水体Raman散射的强度比值和叶绿素浓度之间的关系。实验表明,激发光强不变的情况下,685 nm荧光与水体Raman散射的强度比值,与叶绿素浓度仍满足线性关系。但是,在较高光强激发时,饱和激发造成的叶绿素荧光非线性变化,导致利用传统激光诱导荧光理论反演的叶绿素浓度值偏小。因此,需要对饱和激发下荧光非线性的影响进行修正,其关系为I_F/R=n_chl/C+C_F,修正值C_F不可忽略。另外,值得一提的是,修正关系中系统常量C随激发光强增加而增大。研究表明,饱和激发造成的荧光非线性,会对激光诱导荧光技术测量叶绿素浓度产生影响,但由于造成荧光非线性因素的复杂性,仅通过荧光数据拟合获得的多项式,无法定量说明其影响权重。然而,当激发光强不变时,可以实验测量获得基于激光诱导荧光原理的修正关系,从而准确反演叶绿素浓度。     

双光子阵列点激发同时多维荧光信息的处理

五维同时荧光信息显微成像方法是一种新的荧光信息获取技术，它采用了双光子阵列点激发方式.这一方法可同时获取激发阵列点每点荧光的位置信息、荧光光谱信息和荧光寿命信息，弥补了现有荧光检测技术的不同功能信息不具有同时性的缺陷.给出了从这种技术的复合信息中提取复合光谱几何强度结构图像、不同光谱几何强度结构图像、不同光谱寿命图像的方法.提出了一种激发荧光强度修正系数矩阵方法，消除阵列点激发光强不均匀对激发荧光强弱产生的不利影响，取得明显效果.实验对实际样品做了数据采集和处理，给出图像结果，表明处理的效果良好.对存在的问题也作了讨论. 关键词： 荧光信息处理 双光子 荧光光谱 荧光寿命     

一种实现显微荧光寿命图的测量方法

将脉宽120fs、重复率76MHz激光引入激光扫描显微镜的激发光路,利用其扫描系统对荧光标记样品激发扫描,将激发出的荧光从荧光探测光路引入备用的外部探测口;在探测口接一快速光电倍增管,将光电倍增管的信号送给时间相关单光子计数器,获得时间相关的荧光强度图;最后通过计算机处理获得荧光寿命图。应用此系统对青色荧光蛋白(CFP)、黄色荧光蛋白(YFP)荧光寿命进行了测量,并应用CFP、YFP实现荧光共振能量转移的测量。通过实验看出利用已有的激光扫描显微镜,配合较先进的寿命测量方法,可以很好地实现显微荧光寿命图的测量。     

机油产品激光诱导荧光特性的研究

利用紫外脉冲激光和光电倍增管相结合测量机油产品激光诱导荧光的光谱特性和时间特性.分析了荧光光谱的产生,给出了时间分辨荧光光谱的测量.实际测量了一种应用广泛的燕山机油的时间分辨荧光的光谱分布和荧光寿命,测得的荧光谱分布结果和文献中报道的相同.     

激光诱导时间分辨固体表面荧光光谱系统

采用斜射式激发样品光路结构,设计了应用于测试时间分辨固体表面荧光光谱系统。利用该系统研究了氧化锌薄膜在355 nm激光脉冲激发下的时间分辨固体表面荧光光谱。结果表明,该系统能够实现测量时间分辨固体表面荧光光谱,并由此测量了样品的固体表面荧光寿命。该系统结构简单可靠,灵敏度高,响应速度快。     

机油类产品激光诱导荧光时间特性的研究

介绍了一种由三倍频Nd∶YAG激光器、单色仪、光电倍增管以及信号采集处理系统构成的激光荧光谱寿命测量系统及其测量原理和方法,讨论了如何去除激发光脉冲宽度和探测系统响应速度对测量结果的影响,并实际测量了一种应用广泛的燕山机油的荧光谱寿命.本系统具有简便、快捷、准确以及成本低等优点,适合用于未来实用化机载水面监测激光荧光雷达遥感系统中 关键词： 激光诱导荧光 荧光寿命 Nd∶YAG激光器 光电倍增管     

荧光激光雷达技术探测水面油污染系统仿真研究

为实现对水面油污染的探测, 根据荧光激光雷达系统的发展趋势, 采用激光诱导荧光技术, 建立了适用于水面油污染探测荧光激光雷达的系统模型. 提出采用单激光器结合增强电荷耦合器件的小型荧光激光雷达探测系统, 通过分析激光器单脉冲能量与探测浓度之间的关系, 结合荧光激光雷达系统参数, 对系统模型的探测能力与信噪比等进行了数值仿真. 结果表明, 系统选用单脉冲能量50 μJ的355 nm Nd:YAG激光器作为激发光源, 白天在7 m的距离处探测信噪比可以达到10, 满足实验室搭建模拟系统的要求. 针对实际探测水面油污染, 提出采用增大激光器功率的方法, 并通过模拟计算验证了采用50 mJ的单脉冲能量激光器在230 m的探测距离处可得到与实验室相同的结果, 对实际系统的搭建具有指导意义.     

激光诱导荧光寿命及其测量

激光诱导荧光特性的研究可用于包括心血管病在内的多种疾病的诊断。荧光发射包括光谱（频域）和时间（时域）两方面的信息，后者表现为荧光寿命。在很多情况下，测量荧光寿命是比测量光谱更为有效的诊断方法。本文从理论上讨论了荧光寿命问题，并介绍两种测量方法，可用于测量人体正常组织和病变组织的激光诱导荧光寿命     

Remote Estimation of the Chlorophyll Concentration of Living Trees Using Laser-induced Fluorescence Imaging Lidar

Monthly variation in chlorophyll concentration of living ginko tree leaves 65 m away from a system was remotely estimated by a laser-induced fluorescence imaging lidar. The combination of a pulsed laser and a short-time gated CCD using an image intensifier made it possible to monitor the weak fluorescence signal from the ginko tree leaves as an image. By applying the experimental idea that a ratio of intensity of the chlorophyll fluorescence at 740 nm to that at 685 nm showed a linear correlation to the chlorophyll concentration, the fluorescence image of the ginko tree obtained by the lidar was converted to the chlorophyll concentration distribution image.     

Frequency-domain fluorescence lifetime imaging for endoscopic clinical cancer photodetection: Apparatus design and preliminary results

We describe a new fluorescence imaging device for clinical cancer photodetection in hollow organs in which the tumor/normal tissue contrast is derived from the fluorescence lifetime of endogenous or exogenous fluorochromes. This fluorescence lifetime contrast gives information about the physicochemical properties of the environment which are different between normal and certain diseased tissues. The excitation light from a CW laser is modulated in amplitude at a radio frequency by an electrooptical modulator and delivered by an optical fiber through an endoscope to the hollow organ. The image of the tissue collected by the endoscope is separated in two spectral windows, one being the backscattered excitation light and the other the fluorescence of the fluorochrome. Each image is then focused on the photocathode of image intensifiers (II) whose optical gain is modulated at the same frequency as the excitation intensity, resulting in homodyne phase-sensitive images. By acquiring stationary phase-sensitive frames at different phases between the excitation and the detection, it is possible to calculate in quasi-real time the apparent fluorescence lifetime of the corresponding tissue region for each pixel. A result obtained by investigating the endogenous fluorochromes present in the mucous membrane of an excised human bladder is presented to illustrate this method and most of the optical parameters which are of major importance for this photodetection modality have been evaluated.     

Biochip fluorescence detection system with spatial and spectral separation

A novel optical arrangement for fluorescence detection that employs spatial separation as well as spectral filter to increase the signal to noise ratio is proposed. Using a prism and two mirrors, the elliptical laser beam of a laser diode, as an excitation light, is homogenized and the transmitted excitation light is separated from the fluorescence not to reach the collecting optics. Uncooled CCD can capture the fluorescence image of up to 40 fluorescently-labeled protein patterns without scanning or mechanical translation. This paper presents the simulation, construction and measurement results of the developed optical system. The measurements show that the combination of prism and mirrors converts the excitation light from the laser diode to uniform illumination on the specimen, and provides the separation between excitation and fluorescence light to give high signal to noise ratio. It is also possible to assay various protein concentrations ranging from 1000 to 10 ng/ml reliably. We believe that the proposed fluorescence detection system can be used to build a commercially valuable, low cost, hand-held or miniature fast detection device for point-of-care applications.     

An integrated phase-resolved fluorescence imaging system with sub-nanosecond lifetime resolution

In this paper, a novel configuration of an integrated phase-resolved (PR) fingerprint fluorescence imaging system is proposed and implemented. In this integrated PR imaging system, a current modulated 402 nm dual diode laser is proposed to be the light source, to obtain both high laser power and easy modulability. To estimate the lifetime resolution of this PR imaging system, a novel method of using distance-selective suppression of fluorescence signals from two identical fluorescing samples is proposed. Detailed theoretical and experimental analyses are presented. The experimental results demonstrate that this integrated PR imaging system has a lifetime resolution of 0.1 ns. Fingerprint detection experiments are also carried out using this system with latent fingerprints deposited on substrates of aluminum foil and currency.