瓦状阻尼橡胶块对高铁车轮减振降噪的影响分析

依据声学测试标准,为了评价某型高铁车轮在安装不同形式橡胶块装置后的减振降噪效果,在半消声室内基于B&K振动噪声测试分析系统,对裸轮和橡胶块车轮开展振动声辐射室内测试实验,并基于有限元方法对车轮模态进行了仿真分析。测试结果可知:相比裸轮,WA、WB车轮模态阻尼比显著增加,车轮的减振效果明显,其中WA车轮的减振效果略优于WB车轮。径向激励下,WA车轮声功率级降低了8 dB(A),WB车轮声功率级降低了5.5 dB(A);轴向激励下,WA车轮声功率级降低了8.2 dB(A),WB车轮声功率级降低了6.2 dB(A)。分析可知橡胶块装置能有效抑制车轮的滚动噪声和曲线啸叫,对车轮的减振降噪有积极作用。     

阻尼贴片式高速列车车轮振动声辐射试验分析

为了研究辐板不同阻尼贴片装置对高速列车车轮的减振降噪效果,在半消声室内进行标准车轮与阻尼贴片式车轮自由状态下的振动声辐射试验研究,并基于有限元法对车轮模态进行了仿真计算。研究结果表明：施加辐板阻尼贴片后,两种阻尼贴片车轮的固有频率与标准车轮相比变化不大,但对于频率在1600Hz以上各阶模态阻尼比显著增加。径向与轴向激励下的降噪效果均达到10dB(A)以上,可见两种阻尼贴片装置均具有良好的降噪效果。其中在多了0.3mm铝合金薄板的情况下,W2车轮的降噪效果要略优于W1车轮,轴向激励下更加明显。     

地铁车辆直型辐板阻尼环车轮声振特性分析

为探究地铁车辆阻尼环扩张状态对阻尼环车轮声振特性影响,在半消声室内进行阻尼环车轮自由状态下的声振特性实验研究,结合有限元仿真对实验结果进行分析。研究表明,环-轮组合振动固有频率与原车轮相比变化不大,但阻尼环使车轮的模态阻尼比显著增加,有效抑制了车轮各模态的振动幅值。改变阻尼环扩张状态,阻尼环降噪效果发生非线性变化,幅值在5.6 dB(A)之内。阻尼环扩张状态可通过调节非闭合阻尼环两端扩张装置来改变。阻尼环处于非最大扩张状态W_3时,可获得最佳降噪效果。     

临街住宅阳台降噪缩尺模型研究

本文通过1/10缩尺模型,测得点声源在道路上不同位置时居室内之声级,把声源声功率级与室内 声级之差作为衰减量用于交通噪声计算机模拟过程,即得在某种车流状态下居室内声级.通过比较各种 情况下居室内声级,得出阳台及各种改进措施之降噪值.结果表明,在1—5层范围,阳台无实栏板、无吸 声处理情况下,居室内声级反而高于无阳台居室0—2dB.在上述阳台上做1.1m高实栏板及阳台顶贴 一般吸声材料,两者共有2—5dB降噪效果.取消阳台顶板(强吸声),又能增加1—4dB降噪量.对阳 台上也装窗的封闭阳台,在内外窗错位开启通风情况下,相对无阳台居室可有14—15dB附加降噪量.     

局域共振单元与薄膜复合声子晶体板结构的低频降噪

提出了一种局域共振单元复合声子晶体板结构,并结合有限元对晶体板结构的带隙特性、隔声性能进行了分析.结果表明,共振带隙的产生是由共振单元与板中传播的弹性波相互耦合造成的,耦合强度直接影响共振频率和带隙宽度,隔声效果与薄膜的厚度直接相关.通过改变薄膜的厚度可以将隔声效果调节到满足机舱飞行员正常驾驶的要求.该结构在200dB以下具有良好的隔振效果,最大隔声量达到150dB.该研究为获得良好的隔声效果提供了理论支持,在航空发动机减振降噪方面具有潜在的应用前景.     

腐蚀声发射信号降噪方法

为了从复杂背景噪声中有效地检测出腐蚀声发射信号,采用短时分形维数和离散分数余弦变换相结合的降噪方法,利用声发射检测系统,对6% FeCl₃·6H₂O溶液中Q235钢板的全面腐蚀和局部腐蚀声发射信号进行了降噪处理。实验结果表明,腐蚀声发射信号分别加入白噪声、有色噪声和粉红噪声,在输入信噪比为0~15dB的条件下,此方法降噪效果与标准离散余弦、离散分数余弦变换方法相比,输出信噪比最高可提升8 dB。所述降噪方法对检测腐蚀声发射信号以及对金属剩余寿命的评价具有一定意义。      

旁通管反声降噪应用研究

出口有吸声尖劈的具有流动的主管道上，附加一段旁通管的实验和数值研究表明，旁通管有良好的反声降噪效果，但降噪量及降噪频谱有时还不能满足工程上降噪要求，此外，工程实际管道，出口总是通向大气，与有吸声尖劈假定不符。本文针对这些工程实际问题，提出多段旁通管和出口有反射波时的旁通管反声降噪方法，并给出算例。现场试验的实例表明它是正确的。在不是优化的条件下，得到降噪5dB（A）的好效果。     

次级源近场和管壁弹性对充液管路有源消声性能的影响EI北大核心CSCD

建立了含次级源结构的充液直管有源消声系统数值模型,重点分析了声激励下次级源近场和管壁弹性对有源消声性能的影响。结果表明:次级源近场为非均匀声场,误差点位于该区域时部分频点控制效果较差甚至放大,而处于声场均匀区域时可使降噪量提高10 dB以上,增加误差点数量可使绝大多数频点的降噪量提高5 dB以上;管壁弹性使次级源与管壁间的耦合较强,非对称分布的次级源容易激起管壁振动,导致降噪谷值的出现,采用对称分布的次级源可显著提升控制效果;增加次级源数量能够提高系统的有源无源复合控制效果,但使得管内声场变得复杂,多次级源模型的有源消声效果随频率升高而有所降低。     

襟翼侧缘噪声机理及修型降噪设计

襟翼侧缘噪声是飞机起降阶段机体噪声的重要噪声源。采用极大涡模拟对襟翼侧缘非定常流场进行数值模拟,分析其噪声产生机理.基于此,提出了两种襟翼侧缘修型方式,应用虚拟渗透面的Ffowcs Williams and Hawkings(FW-H)声比拟方法将修型构型的远场噪声频谱特性和指向性与基准构型对比分析,研究其降噪效果。通过流场和声场的数值模拟表明,襟翼侧缘噪声属于宽频噪声。不同的襟翼侧缘形状改变了流场形态、侧缘涡结构以及涡系的发展过程,进而对声源分布和远场噪声特性产生影响。结果表明:在给定的5°计算迎角下,两种襟翼侧缘修型方式在保证增升装置的原有升阻气动特性的前提下,能达到减小全场总声压级1~2 dB的降噪效果。      

子空间降噪在舰船噪声混沌信号处理中的应用

结合混沌信号本身的特性采用子空间投影理论,研究含噪Lorenz模型信号和水下舰船噪声信号的降噪问题。讨论了延迟时间和嵌入维对降噪效果的影响,重点研究了为保持混沌信号的局部特性如何选择参与自相关函数计算的信号长度。采用分段自相关函数多次迭代的方法,保持了混沌的局部特性。仿真结果表明,降噪效果较为理想。     

非圆化磨耗激励下高速列车转向架区域噪声边频带产生机理及影响

该文通过对车辆噪声和车轮非圆化磨耗开展跟踪测试和分析,发现存在车轮非圆化磨耗的列车在运行过程中,其转向架区域噪声窄带频谱上会出现了以非圆化磨耗激励频率为中心,以过轨枕频率为间隔等间距分布的噪声峰值(即噪声边频带).这使得车轮非圆化磨耗不仅会影响其激励频率处的列车轨道结构的振动和噪声,还会对其他频段的噪声产生重要影响.为...     

某型振动轮噪声数值模拟及优化分析

空中声源的辐射噪声谱包括宽带连续谱和窄带线谱,线谱能量高于连续谱。与水下声源相比,空中声源的运动速度普遍较高,线谱多普勒频移明显,可用于进行水下对空中声源的运动参数估计。首先通过时频分析提取接收信号的瞬时频率,而后利用非线性最小二乘法将瞬时频率提取值与预测值相拟合,进而估计声源的运动参数(声源的运动速度、静止频率、与接收器最小水平距离及经过最近点时刻)。仿真与实验均能较为准确地估计出声源运动参数,同时在实验中实现了水下对空中运动声源的测距和定位,测距误差小于15.8%。在满足一定信噪比和保证足够多普勒信息的情况下,该参数估计方法具有很好的适用性。     

Wheel/rail noise—Part II: Wheel squeal

A model is presented for the intense pure-tone noise generated by American subway cars and German trams when traversing tight curves. Squeal is presumed to arise from lateral crabbing of the wheels across the rail head, which results from the finite length of the truck (or bogie). This lateral sticking and slipping causes vibrations in the wheel to increase until a stable amplitude is reached. The stick-slip mechanism is described by a negative damping coefficient that varies with vibration amplitude. The model is used to predict the intensity of wheel squeal as a function of train speed, curve radius, and truck length. Damped and resilient wheels were tested and found effective at reducing wheel squeal.     

Experimental study of the effect of viscoelastic damping materials on noise and vibration reduction within railway vehicles

Interior noise and vibration reduction has become one important concern of railway operating environments due to the influence of increased speeds and reduced vehicle weights for energy efficiency. Three types of viscoelastic damping materials, bitumen-based damping material, water-based damping coating and butyl rubber damping material, were developed to reduce the vibration and noise within railway vehicles. Two sleeper carriages were furnished with the new materials in different patterns of constrained-layer and free-layer damping treatment. The measurements of vibration and noise were carried out in three running carriages. It is found that the reduction effect of damping treatments depends on the running speed. The unweighted root-mean-square acceleration is reduced by 0.08–0.79 and 0.06–0.49 m/s² for the carriage treated by bitumen-based as well as water-based damping materials and water-based damping material, respectively. The first two materials reduce vibration in a wider frequency range of 63–1000 Hz than the last. It turns out that the damping treatments of the first two reduce the interior noise level by 5–8 dBA within the carriage, and the last damping material by 1–6 dBA. However, the specific loudness analysis of noises shows that the noise components between 125 and 250 Hz are dominant for the overall loudness, although the low-frequency noise is noticeably decreased by the damping materials. The measure of loudness is shown to be more accurate to assess reduction effect of the damping material on the acoustic comfort.     

The research on semi-active muffler device of controlling the exhaust pipe’s low-frequency noise

In order to control low frequency noise in exhaust pipe, this paper puts forward a new concept of H-Q tube based semi-active muffler device. The semi-active muffler device and bench testing system have been designed and operated. Finite element simulation study on semi-active muffler and experimental study on semi-active muffler and passive muffler have been carried on. The effect of simulation and experiment are consistent. The semi-active muffler device acts well in low frequency band, especially between 50 Hz and 150 Hz. The average level of noise reduction is around 35 dB, which is much better than passive muffler. Between 150 Hz and 350 Hz, semi-active muffler has a better performance than passive muffler; above 350 Hz, it has worse performance compared with the passive muffler.     

海洋环境噪声场对称性分析及噪声消除方法

实际的海洋环境是非常复杂的,存在着海洋自噪声、舰船噪声、生物发声等,阵元接收到的噪声信号存在一定的相关性,此时基于传统阵列信号处理的目标方位估计方法的性能将变差,针对这一问题,提出了一种实部消除方法.首先从阵元接收环境噪声的物理机理出发,将圆环阵接收的噪声场分解为对称噪声场和非对称噪声场,并且研究发现对称噪声场只影响数据协方差矩阵的实部.然后通过消除协方差矩阵实部,达到消除对称噪声场的目的,提高信噪比,但是同时产生了虚假声源.针对虚假声源的问题,提出了基于优化算法重构协方差矩阵实部的方法,消除了虚假声源的影响.仿真分析与海试数据处理结果表明:该方法明显消除了对称噪声,提高了信噪比,改善了阵列信号处理算法的性能.实部消除方法易于实现,有一定的工程应用价值.     

Enhancement of noise reduction efficiency based on compensation in the ANC headset using fixed-point DSP

In this paper, we have proposed a new algorithm considering commutation error and feedback effect to enhance the convergence rate and noise reduction efficiency of ANC controller. In order to improve noise reduction performance of the ANC headset with fixed-point DSP, we have proposed a new FxLMS algorithm, FxLMS CF, which considers the commutation error and feedback. Also, using a non-real-time simulation, we have decided the phase and amplitude compensation factors of anti-noise signal considering round-off and quantization error, nonlinear distortion and delay of analog device. We estimated the phase and amplitude compensation factors by simulation without using any special measuring devices or analysis devices, and reduced the broadband noise by 24 dB.