Picosecond laser system with 30-W average power via cavity dumping and amplifying

We present a picosecond laser system with high energy by technologies of cavity dumping and amplifying. Firstly, pulses with 10 ps and ～520 nJ were obtained by cavity-dumped mode-locked laser at 10 kHz repetition rate. Secondly those pulses were seeded into a side-pumped regenerative amplifier (RA). Then pulses output from the regenerative amplifier were amplified by two four-pass post amplifiers. From the laser system pulses with an average power of 30 W corresponding to 3 mJ pulse energy were achieved with the pulse-width of 25.4 ps at repetition rate of 10 kHz.     

Ultrafast noncollinear optical parametric chirped pulse amplification in KTiOAsO4

Amplification of femtosecond pulses at 1.56 microm based on noncollinear parametric chirped pulse amplification in a potassium titanyl arsenate (KTA) crystal with pumping at 1.05 microm is reported. The 100 fs pulses of an erbium fiber laser are parametrically amplified while synchronously pumped by an amplified mode-locked Nd:YLF laser. This amplifier has a saturated gain of 65 dB with 30% conversion efficiency and has produced 160 fs pulses with peak powers of up to 0.75 GW. The system produced 380 mW before compression and can be readily scaled to the multiwatt range with bandwidths to support sub-100 fs pulses.     

高重复频率飞秒掺镱光纤放大器

 数值分析了掺镱单模光纤放大器的最佳增益光纤长度，并在实验上对掺镱单模光纤放大器和光栅对压缩器进行了研究。以最大平均输出功率为7 mW、重复频率为25.4 MHz、脉宽为56 ps的被动锁模环形腔掺镱光纤激光器作为种子脉冲，用250 mW的976 nm单模半导体激光器分别泵浦3种不同长度的掺镱单模光纤，对种子光进行放大，并用光栅对压缩器对放大后的脉冲在不同光栅距离上进行了压缩实验研究。当掺镱单模光纤长度为1.2 m时得到了较好的放大效果，种子脉冲被放大到140 mW，相应的增益为13 dB，放大后的单脉冲能量为5.5 nJ。在光栅距离为14.1 cm时获得了最短440 fs的脉冲，压缩后的功率为43 mW，相应的峰值功率为3.8 kW。     

Broadband high-energy diode-pumped Yb:KYW multipass amplifier

We report a diode-pumped Yb:KYW amplifier delivering up to 27 mJ pulses at a repetition rate of 100 Hz and a spectral bandwidth of 5.5 nm, centered at around 1030 nm. The system is based on a double-head multipass amplifier configuration where the pump thermal load is distributed over two relatively thin laser crystals, which permits a sufficiently large number of passes with minimal passive losses, thus maximizing the energy extraction efficiency. The amplified pulse bandwidth theoretically supports 340 fs pulses, and as a demonstration, a small fraction of the amplified pulses has been compressed to 560 fs.     

基于大基模体积的10mJ飞秒钛宝石激光再生放大器

文章报导了基于大基模体积的高能量飞秒钛宝石激光再生放大器的设计与实验研究,在重复频率10 Hz、抽运能量60 mJ的激励下,得到了单脉冲能量17.4 mJ的种子脉冲放大结果,压缩后的脉冲宽度为40.6 fs,能量为13.9 mJ.借助于此大基模体积再生腔,仅增加一级多通放大,实现了峰值功率达1.9 TW飞秒激光脉冲输出.结果表明,大模体积再生放大不仅降低了后续放大对抽运能量的要求,也可以单独压缩实现再生腔直接输出10 mJ量级的飞秒激光脉冲,是大能量高峰值功率飞秒激光系统的优质前端.     

Sub-picosecond pulses at 100 W average power from a Yb:YLF chirped-pulse amplification system

We present a high-repetition-frequency, diode-pumped, and chirped-pulse amplification system operating at 106 W average output power with excellent beam quality (M(2)=1.3), based on cryogenically cooled Yb:YLF. 1 nJ seed pulses, derived from a mode-locked Ti:sapphire laser, are first amplified to 1 mJ pulse energy at 10 kHz repetition frequency in a regenerative amplifier. The second-stage, multipass amplifier increases the pulse energy to 10.6 mJ, resulting in a spectral width of 2.2 nm. The pulses are compressed to 865 fs in duration, which is 1.26 times the transform limit.     

Conditions of the generation of subnanosecond pulses in a THL-100 laser system

The results from the generation and amplification of positively chirped pulses of 0.05 ns duration at a central wavelength of 475 nm in a THL-100 laser system are presented. It is found that the initial complex allows the generation of such radiation pulses with Gaussian intensity profiles and energies of up to 7 mJ. When such pulses with energies of 2–4 mJ are amplified in an XeF(C-A) amplifier, it is possible to achieve a saturation mode and obtain at the output laser beams with energies of up to 3.2 J. The possibility of compressing subnanosecond pulses at a wavelength of 475 nm in a compressor based on diffraction gratings is demonstrated.     

A 10-Hz terawatt class Ti:sapphire laser system: Development and applications

We developed a two-stage Ti:sapphire laser system to generate 16 mJ/80 fs laser pulses at a pulse repetition rate of 10 Hz. The key deriver for the present design is implementing a highly efficient symmetric confocal pre-amplifier and employing a simple, inexpensive synchronization scheme relying only on a commercial digital delay generator. We characterized the amplified pulses in spatial, spectral and temporal domains. The laser system was used to investigate various nonlinear optical processes, and to modify the optical properties of metal and semiconductor surfaces. We are currently building a third amplifier to boost the laser power to the multi-terawatt range.     

High-peak-power femtosecond pulse compression with polarization-maintaining ytterbium-doped fiber amplification

We report the generation of 140 fs pulses with a peak power of up to 270 kW using a fiber pulse source based on a polarization-maintaining ytterbium-doped fiber amplifier and a semiconductor saturable absorber mirror mode-locked fiber laser seed. The seed laser pulses were amplified and chirped in the fiber amplifier and subsequently compressed in an external transmission grating pair. The use of a polarization-maintaining amplifier addresses nonlinear polarization-induced limitations to the obtainable compressed pulse duration and quality that can arise if isotropic fiber amplification is used. Numerical simulations of the system support the experimental measurements and also confirm the role of fiber dispersion in obtaining high-quality compressed pulses.     

A 61-mJ, 1-kHz cryogenic Yb: YAG laser amplifier

We report a diode-pumped rod-type Yb:YAG laser amplifier operating at 1 kHz. Cryogenic cooling method was adopted to make the Yb:YAG crystal work with four-level behavior. A single-frequency fiber laser acts as the seed in an actively Q-switched Yb:YAG oscillator. The resonator delivers 5.75-mJ pulses at 1 kHz with a pulse duration of approximately 40 ns. The pulses were amplified to 61 mJ in a four-pass rod-type Yb:YAG amplifier with optical-to-optical efficiency of 24% in the main amplifier. The M² parameter of the output laser is <1.4.     

54-fs, 1-GW, 1-kHz pulse amplification in Cr:forsterite

30-fs pulses at 1.22 microm are produced by a self-mode-locked Cr:forsterite laser and amplified in a Cr:forsterite regenerative amplifier by a chirped-pulse amplification technique. 54-fs, 1-GW pulses at a 1-kHz repetition rate are obtained.     

High-average-power kilohertz-repetition-rate sub-100-fs Ti:sapphire amplifier system

We report on a femtosecond Ti:sapphire laser amplifier system that generates pulse energies >5 mJ at a 1-kHz repetition rate. The system consists of regenerative and multipass amplifiers and uses the technique of chirped-pulse amplification. When the system was seeded with 70-fs pulses at 800 nm from a self-mode-locked Ti:sapphire oscillator, amplified pulses of 94-fs duration at a repetition rate of 1 kHz and an average output power of 5.4 W were produced. The amplified pulse-repetition rate is variable from 250 Hz to 3 kHz. Pulse energies of >7.5 mJ were obtained at 500 and 250 Hz.     

Kilowatt-peak-power, single-frequency, pulsed fiber laser near 2 μm

We generated single-frequency pulses at kilowatt peak power from an all-fiber Tm-doped master oscillator power amplifier system, which is the first report of this kind (to the best of our knowledge) of a laser in the 2 μm region. Compared with the laser linewidth of seed pulses, spectral broadening by a factor of 3 was observed with the amplified pulses. This was attributed to self-phase modulation in passive pigtail fibers of the components (isolator and wavelength division multiplexing) that were placed after the fiber amplifier. The short pulse width (~7 ns) of the kilowatt-level pulses prevents an onset of stimulated Brillouin scattering in the long fiber. When launching the pulses into several-meter single-mode fiber, significant nonlinear spectral broadening occurs due to modulation instability in the fiber. This reaction is beneficial for generation of a mid- and long-wavelength IR supercontinuum in nonlinear IR fibers.     

Picosecond pulses with 50 W peak power and reduced ASE background from an all-semiconductor MOPA system

Using a single-stage all-semiconductor master oscillator-power amplifier system, consisting of a Q-switched distributed Bragg reflector laser as master oscillator and a tapered power amplifier, we generate laser pulses with a length of 80 ps and a peak power of 50 W. The spectral width is less than 1 nm around a center wavelength of 1066 nm. The background of the amplified spontaneous emission is significantly reduced due to a pulsed, instead of continuous-wave operation of the amplifier. The current pulses have a width of approximately 10 ns and a repetition frequency of 1.25 MHz.     

Multiterawatt laser system based on optical parametric chirped pulse amplification

A compact multiterawatt laser system based on optical parametric chirped pulse amplification is demonstrated. Chirped pulses are amplified from 20 pJ to 900 mJ by two lithium triborate optical parametric preamplifiers and a final KDP optical parametric power amplifier with a pump energy of 5 J at 532 nm from Nd:YAG-Nd:glass hybrid amplifiers. After compression, we obtained a final output of 570-mJ-155-fs pulses with a peak power of 3.67 TW, which is the highest output power from an optical parametric chirped pulse amplification laser, to the best of our knowledge.     

Femtosecond diode laser MOPA system at 920 nm based on asymmetric colliding pulse mode-locking

We report on the generation of 267 fs long pulses with a peak power of 661 W emitted by an InGaAs diode laser master-oscillator power-amplifier (MOPA) system with an external grating compressor. The oscillator emits strongly chirped picosecond pulses with several nanometer of bandwidth, which can be amplified without significant phase modulation and are compressed to femtosecond pulses after leaving the amplifier. We used a diode laser module for asymmetric colliding pulse mode-locking and optimized the collision point and the relative intensity of the counter-propagation pulses.     

Self phase modulation in a femtosecond pulse amplifier with subsequent compression

The pulses from a colliding-pulse mode-locked dye laser (100 fs, 20 pJ) are amplified to 0.2 mJ and self phase modulated in an excimer laser pumped dye amplifier. Suitable chirp compensation leads to nearly bandwidth-limited pulses of about 50 fs duration.     

全固态kHz啁啾脉冲飞秒激光放大器

要建造大功率超强激光系统,必须将nJ量级的种子进行放大,以得到mJ量级以及更高能量的激光输出.为达到这个目的,必须使种子能量指数增加,再生腔放大器是实现这一目的的良好途径;同时,为了得到更稳定的激光输出,须采用高重复频率的泵浦源.为此,设计了一种kHz重复频率激光泵浦的再生放大器,使用15 mJ的527 nm的绿光泵浦,得到了约2.3 mJ的800 nm放大激光输出,同时,对其输出激光的光谱特性进行了测量,将带宽为40 nm的种子注入后,得到了光谱带宽约为30 nm激光输出.     

光子晶体光纤飞秒激光非线性放大系统的耦合动力学过程研究

构建了掺镱大模场面积单偏振光子晶体光纤飞秒激光非线性放大系统. 讨论了腔内净色散量和抽运功率对振荡级输出参数的影响和振荡级参数对放大级输出参数的影响. 在本实验条件下, 当腔内净色散量取较大负色散时, 振荡级直接输出的脉冲更宽, 且携带更少的啁啾. 当振荡级抽运4.53 W时, 选择最接近变换极限的脉冲作为种子脉冲, 放大级在60 W抽运时输出压缩后无基底的短脉冲, 宽度为45.7 fs, 平均功率28 W. 振荡级抽运功率增加到5.08 W, 放大级抽运70 W时, 获得最高输出功率34.5 W, 对应脉宽53.5 fs.     

Red picosecond pulses generated by frequency doubling a Raman amplified widely tunable 1.3 microm fiber ring laser

We generated 0.66 microm picosecond pulses by second-harmonic generation of the Raman amplified output of a 1.3 microm actively mode-locked fiber ring laser in a periodically poled potassium titanyl phosphate (PPKTP) waveguide. The ring laser produced 9 ps pulses at a 20 GHz repetition frequency, was tunable over 1284-1330 nm, and was based on a semiconductor optical amplifier and a Mach-Zehnder amplitude modulator. The Raman amplifier served both to amplify the ring laser and to compress the pulses as solitons. The spectral flexibility of the amplifiers and the modulator should enable similar configurations to be made at other wavelengths and facilitate efficient frequency doubling in waveguides to other visible wavelengths.