化整为零:聚合物/粘土纳米复合材料的微观结构和阻隔性能

在聚合物基体中掺入少量的层状硅酸盐所制备的聚合物／粘土纳米复合材料，其阻隔性能明显地优于纯聚合物及其传统的复合材料。实验及分析结果表明，聚合物／粘土纳米复合材料的微观结构和阻隔性能主要受控于粘土剥离后的径厚比．一简单的重整化群模型被用来评估粘土几何因素（诸如径厚比、取向、剥离程度等）对聚合物／粘土纳米复合材料阻隔性能的影响，所得到的逾渗阈值及最佳粘土含量与实验结果吻合。     

纳米粘土增强环氧树脂复合材料抗原子氧性能的研究

本文采用激光爆破法高能原子氧束源研究了纳米粘土增强环氧树脂复合材料的抗原子氧性能. 研究了四种样品：纯环氧树脂,纳米粘土含量为1 wt%,2 wt%和4 wt%的纳米粘土增强环氧树脂复合材料,结果表明腐蚀深度随着纳米粘土含量的增加而降低,当掺杂纳米粘土含量为4 wt%时,腐蚀深度为纯环氧树脂腐蚀深度的28%∽37%;X射线光电子能谱(XPS)分析表明原子氧轰击后,材料表面C-C/C-H键比例减少,C-O键、酮类比例增加,表面氧化程度增加,掺杂纳米粘土的材料表面生成了新的碳酸盐,掺杂4 wt%纳米粘土的复合材料表面氧化程度增加最小;扫描电子显微镜(SEM)结果显示含有纳米粘土的复合材料表面被原子氧轰击后在纳米粘土团簇处形成了“块状”物质,掺杂4 wt%纳米粘土的复合材料,“块状”物质尺寸和分布密度最大;综合腐蚀深度,XPS,以及SEM结果表明,虽然所有表面都一定程度地被原子氧腐蚀和氧化,但掺杂纳米粘土的复合材料表面由于生成了“块状”物质,阻挡了原子氧进一步腐蚀其下的材料,提高了抗原子氧性能.     

纳米粘土增强环氧树脂复合材料抗原子氧性能的研究（英文）

本文采用激光爆破法高能原于氧束源研究了纳米粘土增强坏氧树脂复合材料的抗原子氧性能.研究了四种样品:纯环氧树脂,纳米粘土含量为1 wt%,2 wt%和4 wt%的纳米粘土增强环氧树脂复合材料,结果表明腐蚀深度随着纳米粘土含量的增加而降低,当掺杂纳米粘土含量为4 wt%时,腐蚀深度为纯环氧树脂腐蚀深度的28%～37%;X射线光电子能谱(XPS)分析表明原子氧轰击后,材料表面C-C/C-H键比例减少,C-O键、酮类比例增加,表面氧化程度增加,掺杂纳米粘土的材料表面生成了新的碳酸盐,掺杂4 wt%纳米粘土的复合材料表面氧化程度增加最小;扫描电子显微镜(SEM)结果显示含有纳米粘土的复合材料表面被原子氧轰击后在纳米粘土团簇处形成了"块状"物质,掺杂4 wt%纳米粘土的复合材料,"块状"物质尺寸和分布密度最大;综合腐蚀深度,XPS,以及SEM结果表明,虽然所有表面都一定程度地被原子氧腐蚀和氧化,但掺杂纳米粘土的复合材料表面由于生成了"块状"物质,阻挡了原子氧进一步腐蚀其下的材料,提高了抗原子氧性能.     

氧化石墨烯/硒化锌纳米光电材料的制备及其蓝光发射特性

采用一种简单有效的原位水热合成方法,使用石墨烯氧化物（GO）作为反应物和晶体生长基底成功制备出了还原氧化石墨烯/硒化锌（r-GO/ZnSe）纳米复合材料。采用X射线粉末衍射（XRD）、透射电子显微镜（TEM）、高分辨透射电镜（HRTEM）以及红外-可见光谱（FT-IR）等方法对r-GO/ZnSe纳米复合材料进行了检测。结果表明,平均粒径在30 nm的立方闪锌矿晶体结构的ZnSe粒子均匀分散在氧化石墨烯片层上,构成纳米复合结构。 UV-Vis光谱显示,纳米复合材料的光学吸收的起始波长在445 nm附近。PL光谱显示,纳米复合材料在470 nm附近存在一个很强的发射峰。这种石墨烯基纳米复合材料在白光二极管领域中有重要的应用价值。     

高压对纳米ZnO和ZnO/SnO2复合材料的结构和发光性能的影响

 利用溶胶-凝胶法制备出了纳米晶ZnO与含有3%摩尔分数SnO₂的ZnO/SnO₂复合材料,在六面顶压机上对制备出的两种样品进行了室温下、6GPa的高压处理。采用X射线衍射（XRD）、透射电子显微镜（TEM）和光致荧光谱（PL）等方法,对高压处理前后样品的结构和发光性质进行了表征。结果表明：高压处理后回收到的纳米晶ZnO和ZnO/SnO₂复合材料的平均粒径分别减小5.9%和26.3%;高压处理后ZnO和ZnO/SnO₂复合材料光致发光谱的发光带强度都有所降低,但ZnO/SnO₂复合材料发光带强度降低幅度比纯ZnO小,对产生这些现象的原因进行了讨论。     

NiFe2O4纳米固体的穆斯堡尔谱研究

利用反滴共沉淀法制备了ＮｉＦｅ₂O₄纳米粒子，并在高压下（４.５ＧＰａ）压制成块状纳米固体材料．Ｘ射线衍射显示，ＮｉＦｅ₂O₄纳米固体的晶体结构和平均晶粒尺寸在高压下均没有发生变化．但其室温和低温穆斯堡尔谱结果表明，高压对纳米固体内部的磁相互作用和界面原子状态有很大的影响．在高压下，纳米固体内部的颗粒间磁偶极相互作用和界面离子间的超交换相互作用显著增强．从而明显抑制了ＮｉＦｅ₂O_{4关键词：}     

钨/石墨烯/钨面向等离子体复合材料力学与热学及耐辐照性能衰减的第一性原理计算

通过第一性原理计算研究了钨/石墨烯/钨复合材料相比于纯钨金属在力学与热学性质方面的变化，并用氦原子-空位缔合缺陷模拟核聚变辐照损伤评估等离子体辐照条件下的性能。计算结果表明：钨/石墨烯/钨复合材料的体积弹性模量、杨氏模量与剪切模量呈现一定程度的下降，但是提升了钨基材料的延展性；钨/石墨烯/钨复合材料的热膨胀系数有所增加，但是具有较高的最小热导率。本文阐述了石墨烯界面层可以对基体杂质与缺陷进行吸附的独特机制，通过这种机制，钨/石墨烯/钨复合材料在力学、热膨胀系数以及最小热导率有更低程度的衰减，这显示了钨/石墨烯/钨复合材料在抗辐照性能方面具有较大的应用潜力。     

液氮温区用树脂基非线性复合材料性能研究

电场分布不均匀是超导装备高压引线存在的技术难题,使用非线性复合材料可以有效改善终端电场分布不均匀现象.本文选用双酚F树脂基体,通过加入纳米氧化锌和炭黑无机填料制备了具有非线性电导特性的树脂基复合材料,实验研究了纳米无机填料的种类、添加量等对复合材料电导性能、工频击穿性能和机械性能的影响.     

基于聚乙烯/蒙脱土纳米复合材料微观结构的力学性能模拟

模拟分子的结构与行为有助于更深刻地分析聚乙烯/蒙脱土(PE/MMT)纳米复合材料力学性能变化的微观机理.为此,以分子动力学为依据,利用Materials studio构建聚乙烯/蒙脱土纳米复合材料模型.在普适力场作用下,通过X射线衍射、径向分布函数以及相互作用能分别对纳米复合材料和纳米蒙脱土的微观结构和性能进行分析.仿真结果表明:有机化处理使蒙脱土的层间距增大79%;在蒙脱土质量分数为4.0 wt%时,PE/MMT纳米复合材料中存在明显的氢键作用,聚乙烯分子和蒙脱土片层间的相互作用能高达-390 kcal/mol,界面作用得到明显提高,最终形成稳定的材料结构,同时力学性能相比纯聚乙烯材料也得到改善,其中杨氏模量、体积模量以及剪切模量分别提高38%,21%和40%.分子模拟结果与实验实测结果相符,并验证了有机化蒙脱土改性聚乙烯绝缘材料会产生氢键作用.     

钨/石墨烯/钨面向等离子体复合材料力学和热学及其抗辐照性能的第一性原理计算研究

通过第一性原理计算研究了钨/石墨烯/钨复合材料相比于纯钨金属在力学与热学性质方面的变化，并用氦原子-空位缔合缺陷模拟核聚变辐照损伤评估等离子体辐照条件下的性能.计算结果表明:钨/石墨烯/钨复合材料的体积弹性模量、杨氏模量与剪切模量呈现一定程度的下降，但是提升了钨基材料的延展性;钨/石墨烯/钨复合材料的热膨胀系数有所增加，但是具有较高的最小热导率.本文阐述了石墨烯界面层可以对基体杂质与缺陷进行吸附的独特机制，通过这种机制，钨/石墨烯/钨复合材料在力学、热膨胀系数以及最小热导率有更低程度的衰减，这显示了钨/石墨烯/钨复合材料在抗辐照性能方面具有较大的应用潜力.     

Melt intercalation and exfoliation of maleated polypropylene modified polypropylene nanocomposites

Melt blending of maleic anhydride-grafted polypropylene (PPgMA) and organically modified clay nanocomposites were first prepared in a plasticorder. PPgMAs, including PB3150, PB3200, PB3000, and E43, with a wide range of MA content and molecular weight were used. The structure was investigated with X-Ray diffraction (XRD) and transmission electron microscopy (TEM). PPgMA compatiblizers gave rise to similar degree of dispersion beyond the weight ratio of 3 to 1 with the exception of E43, which had the highest MA content and the lowest molecular weight. It was found that thermal instability and high melt index were responsible for ineffective modification by E43. Furthermore, PPgMA with lower molecular weight and higher melt index had to be compounded at lower mixing temperature in order to achieve a reasonable level of torque for clay dispersion. We then modified polypropylene/organoclay nanocomposites with different levels of PPgMA compatibilizers on a twin-screw extruder. The PP/E43/clay system, as shown through XRD patterns and TEM observation, yielded the poorest clay dispersion among the compatibilizers under investigation. The relative complex viscosity curves also revealed a systematic trend with the extent of exfoliation and showed promise for quantifying the hybrid structure of the nanocomposites. Mechanical properties and thermal stability were determined by dynamical mechanical analysis (DMA) and thermogravimeric analysis (TGA), respectively. Though PPgMA with lower molecular weight would lead to better clay dispersion in the polypropylene nanocomposites, it caused deterioration in both mechanical and thermal properties of the hybrid systems.     

Clay dispersion and physical properties of melt-blended PP/organoclay nanocomposites: effect of interfacial interaction

Melt blending of maleic anhydride-grafted polypropylene (PPgMA) and organically modified clay nanocomposites was first carried out in a plasticorder. The structure was investigated with x-ray diffraction (XRD) and transmission electron microscopy (TEM). The interfacial interaction between PB3150 compatibilizer and I30 clay surface was altered with the addition of different loadings of PB3150. It was found at the PB3150 compatiblizer gave rise to a high degree of clay dispersion beyond the PB3150/I30 weight ratio of 3. We then also modified polypropylene/organoclay nanocomposites with different loadings of PB3150 on a twin-screw extruder. When the PB3150 loading exceeded 15 wt%, extensive exfoliation of clay was observed. The relative complex viscosity curves also revealed a systematic trend with the extent of exfoliation and showed promise for quantifying the hybrid structure of the nanocomposites. Mechanical properties and thermal stability were determined by tensile and impact tests and thermogravimeric analysis (TGA), respectively. Although high loading of PB3150 leads to better clay dispersion in the polypropylene nanocomposites, it causes deterioration in both mechanical and thermal properties of the hybrid systems.     

Polystyrene‐b‐Poly(Ethylene‐r‐butylene)‐b‐Polystyrene Triblock Copolymer/Organoclay Nanocomposites and Their Phase Characteristics

Abstract

Intercalated polymer/clay nanocomposites were prepared using a polystyrene‐b‐poly(ethylene‐r‐butylene)‐b‐polystyrene (SEBS) cylindrical triblock copolymer. Dynamic rheological measurements, x‐ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetry analysis (TGA) were conducted to investigate the internal structure and physical and phase characteristics of the nanocomposites. The XRD data confirmed that the interlayer distance between the anisotropic silicates increased due to the intercalation of SEBS into the clay interlayers. As the clay loading increased, the onset points of the order–disorder transition (ODT) and order–order transition (OOT) were found to decrease, whereas the thermal decomposition temperatures, monitored by TGA, increased with the clay loading.     

有机溶剂热法合成富勒烯[60]-银核壳结构纳米复合物

把C60、硝酸银、还原剂溶解在混合溶剂中,有机溶剂热法制备了C60-Ag核壳结构纳米复合物。用XRD、TEM/HRTEM、UV-Vis、IR等对产物进行了表征。透射电镜表明产物粒径为80—100nm。紫外-可见光谱分析表明C60的吸收峰出现了红移,而纳米银的吸收峰出现了蓝移,表明纳米银和C60之间发生了电荷从银转移给C60的相互作用。     

Parametric Studies on the Grafting of Poly(Methyl Methacrylate) onto Organophilic Montmorillonite Using Silylated Clay Platelets

Poly(methyl methacrylate) (PMMA)/organophilic montmorillonite (Cloisite 30B) nanocomposites were synthesized by the chemical grafting of PMMA onto Cloisite 30B via solution polymerization of methyl methacrylate (MMA) with vinyl-modified organoclay. The effects of different parameters such as clay weight percent (CWP), solvent per monomer volume ratio, and dispersion time on the properties of the PMMA grafted Cloisite 30B were investigated using the Taguchi experimental design method. This method gives a much-reduced variance for the experiments with optimum setting of control parameters and provides a set of minimum experiments compared to the conventional methods. Qualitative evidence for the chemical grafting of the PMMA onto Cloisite 30B was confirmed by Fourier transform infrared spectroscopy (FT-IR). X-ray diffraction (XRD) was used to investigate interlayer changes of the clay in the grafted nanoplatelets. The exfoliated/intercalated morphology of the nanocomposites was confirmed by XRD. Furthermore, thermal properties were measured by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). Statistical analysis of results revealed that clay weight percent and solvent per monomer ratio had significant effects on the properties of final products. The percent of grafted PMMA and storage modulus of PMMA/30B nanocomposites decreased with increasing clay content due to better dispersion of the clay at lower loadings. On the other hand, because of a tendency to formation of homopolymer and oligomers at higher solvent loadings; the percent of grafted PMMA, storage modulus and glass transition temperature of PMMA/30B nanocomposites decreased with an increase in solvent per monomer volume ratio. However, the obtained PMMA/30B nanocomposites at the optimum conditions, was exhibited a higher glass transition temperature, higher storage modulus and better thermal stability than the pure PMMA.     

Morphological and Rheological Properties of Poly(Trimethylene Terephthalate)/Maleic Anhydride Grafted Poly (Ethylene-Octene)/Organoclay Ternary Nanocomposite

Poly(trimethylene terephthalate) (PTT)/poly(ethylene-octene) POE-g-MA/organoclay ternary nanocomposites were prepared using melt blending in order to simultaneously improve the toughness and stiffness of PTT. The phase morphology and dispersion of organoclay were characterized by scanning electron microscope (SEM), X-ray diffractometer (XRD), and transmission electron microscopy (TEM). The melt rheological behavior of the ternary nanocomposites was determined by plate/plate rheological measurements. XRD and TEM analysis indicated that the ternary nanocomposites contained exfoliated nanoparticle when a small amount of organoclay (1 part per hundred) was added. The high aspect ratio of the organoclay platelets induced the average size of the dispersed domain to become smaller. Melt rheological studies revealed that the ternary nanocomposites exhibited strong shear thinning behavior and showed good processability.     

Structure and Mechanical Properties of 50/50 NR/SBR Blend/Pristine Clay Nanocomposites

A blend/clay nanocomposites of 50/50 (wt%) NR/SBR was prepared via mixing the latex of a 50/50 NR/SBR blend with an aqueous clay dispersion and co‐coagulating the mixture. The structure of the nanocomposite was characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). Nanocomposites containing less than 10 phr clay showed a fully exfoliated structure. After increasing the clay content to 10 phr, both nonexfoliated (stacked layers) and exfoliated structures were observed in the nanocomposites. The results of mechanical tests showed that the nanocomposites presented better mechanical properties than clay‐free NR/SBR blend vulcanizate. Furthermore, tensile strength, tensile strain at break, and hardness (shore A) increased with increasing clay content, up to 6 phr, and then remained almost constant.     

Influence of Compatibilizer-Type and Processing Approach on the Dispersion of OMMT in High-Density Polyethylene Matrix

High-density polyethylene/organoclay nanocomposites were prepared via melt intercalation in an internal mixer using both a direct mixing and master batching method. Two types of maleic anhydride grafted polyethylene, high-density polyethylene grafted maleic anhydride, and linear low-density polyethylene grafted maleic anhydride, (HDPE-g-MA, LLDPE-g-MA) were used as compatibilizers to enhance the dispersibility of nanoclay in HDPE. Dispersion of organoclay in the nanocomposites was characterized by using X-ray diffraction (XRD), transmission electron microscopy (TEM), and rheological mechanical spectroscopy (RMS). Effects of clay content and degree of clay dispersion on the rheological and tensile properties were also investigated. Furthermore, the effect of order of mixing on the dispersion and distribution of the clay layers was studied. The obtained results showed that organoclay in the nanocomposites were dispersed homogeneously and exfoliated better when HDPE-g-MA and the direct mixing route were used. Although in the master batching method clay intercalated better, clay layers chiefly remain in compatibilizer rich areas. On the other hand, direct mixing was observed to lead to clay particles being dispersed in the HDPE matrix or at the interface of the matrix and compatibilizer and, consequently, better improvement in the tensile modulus was achieved. It was determined that the compatibilizer with the higher miscibility with the matrix was the key factor for achieving better exfoliation of clay sheets.     

Polymer-Nanoparticle Composites Composed of Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) and Coated Silver Nanoparticles

The effects of addition of synthesized organic-suspension silver nanoparticles on the crystallization and thermal stability of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) were studied by transmission electron microscopy (TEM), differential scanning calorimetry (DSC), wide-angle X-ray diffraction (XRD), UV-Vis absorption spectroscopy, polarized optical microscopy (POM), and thermal gravimetric analysis (TGA). The TEM images showed the average primary size of the as-synthesized silver nanoparticles, coated with a monolayer of the surfactants consisting of oleic acid and an alkylamine, was about 5 nm with narrow distribution, and that they were uniformly dispersed in n-heptane. PHBV/silver nanocomposites were prepared by melt mixing in an internal mixer and then injection molded into rectangle-shaped specimens by a labscale injection molding device. The coated silver nanoparticles showed a homogenuous dispersion in the PHBV matrix when the content of coated silver nanoparticles was about 1%. Both the DSC and POM data showed the efficient heterogeneous nucleation by the coated silver nanoparticles for facilitating PHBV crystallization. The thermal stability of the PHBV/silver nanocomposites improved with the increase in the content of the coated silver nanoparticles.     

Polypyrrole–montmorillonite nanocomposites synthesized by emulsion polymerization

The structural, electrical, magnetic, and thermal properties were investigated for the nanocomposites of polypyrrole (PPy) and inorganic clay (Na⁺-montmorillonite) prepared by emulsion polymerization. Dodecylbenzenesulfonic acid (DBSA) was used as emulsifier (surfactant) and dopant. The X-ray diffraction (XRD) patterns and transmission electron microscopy (TEM) images showed that the conducting PPy was intercalated into the clay layers in nanoscale (<10 Å). The dc conductivity (σ_dc) of PPy–DBSA with clay was 6 S/cm, while that of PPy–DBSA without clay was 20 S/cm at room temperature (RT). Temperature dependence of σ_dc of both samples followed the three dimensional variable range hopping (VRH) model. From the g-value and the temperature dependence of EPR linewidth, paramagnetic signals were strongly affected by the partially negatively charged clay layers. The thermogravimetric analysis (TGA) and differential scanning calorimeter (DSC) showed that the clay induced the thermal stability of the systems.