A full-duplex radio-over-fiber system using direct modulation laser to generate optical millimeter-wave and wavelength reuse for uplink connection

In this paper, we present a full-duplex radio-over-fiber system incorporating both optical millimeter-wave (mm-wave) generation and wavelength reuse for uplink connection. The optical double sidebands (DSB) signal is generated by using only one inexpensive broadband direct modulation laser (DML), to which a mixing RF signal is applied. An optical interleaver is then used to separate the first-order optical sidebands from the optical carrier of optical DSB signal. The separated first-order optical sidebands are beat to generate mm-wave signal that has double the frequency of the RF drive signal, while the separated optical carrier is reused as light source to remodulate uplink signal. Both detailed theoretical analysis and experiments to demonstrate the feasibility of the proposed system are presented. Experiment result shows that the bidirectional 2.5 Gb/s data can be successfully transmitted over 40 km standard single-mode fiber (SSMF) with less than 2 dB power penalty.     

Analysis of an optical mm-wave generation scheme with frequency octupling using two cascaded Mach-Zehnder modulators

We propose a novel method to generate optical mm-wave signals with frequency octupling using two cascaded Mach-Zehnder modulators (MZMs). First, the scheme is investigated both theoretically and by simulation, and results show that an 80 GHz mm-wave is generated by a 10 GHz RF oscillator. Then, an analytical expression is developed to describe the performance of the scheme. The influences caused by non-ideal factors are discussed in detail, and undesired sidebands suppression ratios are plotted and analyzed. At last a RoF system using the mm-wave generation scheme is demonstrated and its BER curves indicate that the performance of the system is still good even if the parameters deviate from the ideal values to a certain degree.     

A novel frequency sextupling scheme for optical mm-wave generation utilizing an integrated dual-parallel Mach-Zehnder modulator

A novel scheme is proposed for frequency sextupling mm-wave generation based on a laser and an integrated dual-parallel Mach-Zehnder modulator (MZM) without optical filter. Theoretical analysis is presented to suppress the undesired optical sidebands for the high quality generation of frequency sextupling mm-wave signal. The performance of the proposed scheme is evaluated by simulations. Utilizing the integrated MZM consisted of two sub-MZMs with extinction ratio of 30 dB, the optical sideband suppression ratio (OSSR) is as high as 29.9 dB and the radio frequency spurious suppression ratio (RFSSR) exceeds 24 dB without any optical or electrical filter. The impact of the nonideal RF driven voltage and phase difference of RF driven signal applied to two sub-MZMs of the integrated MZM on OSSR and RFSSR is discussed and analyzed. After transmission over fiber, the generated optical mm-wave signal demonstrates good performance. Furthermore, the performance of two cases for the proposed scheme is also compared.     

Full-duplex radio-over-fiber system based on a modified single-side band modulation

A full-duplex radio-over-fiber system based on a modified single-sideband using external modulator is proposed and demonstrated. At the central station, a CW lightwave is intensity-modulated by a RF signal to generate a DSB signal. After the central carrier and the two first-order sidebands are separated by a FBG, the central carrier is modulated with a baseband data at 2.5 Gbit/s. Then, it is recombined with the un-modulated first-order sidebands to generate optical millimeter-wave by an optical coupler with a certain coupling coefficient and transmitted to the base station over single-mode fiber. The central carrier and one of the first-order sidebands are beaten to generate the mm-wave when they are detected by an optical receiver. Another first sideband is reused as carrier for uplink connection. The dispersion performance of the generated mm-wave is theoretically analyzed; one can see that the effect of dispersion and requirement of the optical power are reduced. The PIN-PD can avoid working in a high-DC saturation range which may distort the RF components and depress the responsibility of the detector. The stimulant results show that the system can reduce the effect of dispersion effectively, and immune the fading effect and the walking-off signals. It is suitable for a long distance transmission.     

A full-duplex radio-over-fiber link with 12-tupling mm-wave generation and wavelength reuse for upstream signal

A full-duplex radio-over-fiber (RoF) link with a novel scheme to generate 60 GHz mm-waves from a 5 GHz RF signal source is investigated. In the RoF downlink, the required frequency of the RF oscillator is reduced greatly. Since the optical carrier is not modulated by downstream data, part of it is reused to carry upstream data and the upstream data is transmitted to the central station using optical single-sideband modulation. In this way, a single wavelength is used for both downstream and upstream transmissions. Based on this scheme, a full-duplex RoF link is built and its transmission performance is analyzed. Theoretical analysis and numerical simulation show that the downstream signal cannot only eliminate code form distortion caused by time shift of the code edges, but also reduce the influence of the fading effect as the 60 GHz DSB optical mm-wave signal is transmitted along the fiber, and the upstream signal is immune to both fading effect and time shift of the code edges.     

DSB optical mm-wave with signal only on optical carrier generated by embedded LiNbO3 Mach-Zehnder modulator

We have investigated the generation of the 40-GHz double-sideband optical millimeter (mm)-wave with signal carried only by its optical carrier via an embedded LiNbO₃ Mach-Zehnder modulator (LN-MZM). Since the optical carrier and its two first-order sidebands are dominant and their powers are well balanced, the first-order harmonic in the photocurrent gets maximal. As the optical mm-wave signal is transmitted along the fiber, there is no code outline distortion because the signal is only modulated on the optical carrier. Although the first-order harmonic shows the periodical fading effect when the optical mm-wave signal is transmitted along the fiber, its degradation on the radio-over-fiber link can be avoided by adjusting the position of the fading nodes via varying the main MZM bias voltage, and the signal still keeps much good eye diagram even after 50-km fiber transmission. The experimental results prove our theory.     

Power penalty in multitone radio-over-fibre system employing direct and external modulation with optical amplifiers

This paper presents a multitone RoF system employing a central station and a remote antenna station to transmit modulated microwave or mm-wave signals. Two configurations of the system employing direct and external modulation are presented. First, at the central station, the modulating signal is directly and externally modulated at 1549.5 and 1550.5 nm, respectively, and the combined signal is then transmitted using wireless mode. In the second configuration, the combined signal is transmitted over 20 km to the remote antenna station using optical fibre connectivity. At the remote antenna station, both channel wavelengths are separated and amplified with an EDFA and SOA and are detected. The demonstration results show that there exists a small power penalty between the direct and the external modulation. But a large power penalty is reported depending upon the choice of optical amplifier viz. EDFA or SOA. Better performance is recorded in later case. The results also show that power is being distributed among the operating frequency and sidebands adjacent to it after transmission over a fibre link.     

64 GHz optical millimeter-wave generation by octupling 8 GHz local oscillator via a nested LiNbO3 modulator

A novel scheme to generate a 64 GHz optical millimeter (mm)-wave via a nested LiNbO₃ Mach-Zehnder modulator with an 8 GHz local oscillator is proposed and simulated. Since the frequency response of the modulator and the local oscillator frequency are greatly reduced, the bandwidth requirements of the optical and electrical components in the transmitter are significantly decreased. The simulation results show that the generated optical mm-wave signal maintains good performance even after being transmitted over 20 km standard single-mode fiber.     

Optical demultiplexing of millimeter-wave subcarriers for wireless channel distribution employing dual wavelength FBGs

An optical mm-wave demultiplexer is presented. Double sideband modulation with suppressed optical carrier and filtering properties of dual overwritten fiber Bragg gratings are the fundamentals for optical demultiplexing of mm-wave radio-on-fiber signals: using a single optical carrier, Millimeter-wave signals of 20 and 40 GHz frequencies carrying independent data are created, transmitted over fiber, demultiplexed and wireless distributed to be detected and data recovered in a mobile unit. Double sideband modulation with suppressed optical carrier yields no power penalty due to chromatic dispersion, while the filtering properties of the dual overwritten fiber Bragg gratings allow less than −40 dB electrical power interchannel leakage. Independent 2.5 Gb/s On-Off-keyed data have been successfully transmitted through the 20 and 40 GHz channels.     

Generation of optical carrier suppression millimeter-wave signal using one dual-parallel MZM to overcome chromatic dispersion

In this paper, we have proposed a novel approach to generate optical carrier suppression (OCS) mm-wave with signal only carried by one first-order sideband using a dual-parallel MZM in radio-over-fiber (RoF) system, and the transmission performance was also investigated. As the optical mm-wave signal is transmitted along the fiber, there is no time shift of the data symbols resulting from the group velocity dispersion in the fiber because the signal is only modulated on one sideband. The simulation results showed that the eye diagram keeps open and clear even when the optical mm-wave signals are transmitted over 96-km and the power penalty is about 1-dB after fiber transmission distance of 60-km, which is quite consistent with our theoretical analysis. Furthermore, the proposed OCS optical mm-wave generation approach is also used in a full-duplex RoF link based on wavelength reuse at the base station for the uplink due to another pure sideband without carrying data. The bidirectional 2.5-Gbit/s data is successfully transmitted over 40-km standard single mode fiber with less than 0.5-dB power penalty in the simulation. Both the unidirectional RoF downlink and the full-duplex RoF system have good performance.     

Reduction of frequency fading and imperfect frequency response with pre-emphasis technique in OFDM-ROF systems

In this paper, a novel technique is proposed and experimentally demonstrated to reduce the effect of frequency fading (FF) and imperfect frequency response in direct-detection (DD) optical orthogonal frequency division multiplexing-radio-over-fiber (OFD-MROF) systems. To overcome FF effect in the optical fiber and imperfect frequency response in the optical and electrical devices at the high frequency, we pre-emphasize the power of the millimeter wave (mm-wave) OFDM sub-carriers appropriately in the center station. Experimental result of the proposed system shows the received sensitivity has been improved about 2 dB at the BER of 1 × 10^− 4 after 50 km SSMF transmission for 2.5 Gb/s OFDM signal carried on 60 GHz optical mm-wave compared to the original system without pre-emphasis technique.     

60 GHz millimeter-wave generator based on a frequency-quadrupling feed-forward modulation technique

We propose and analyze a prototype of a 60 GHz millimeter-wave (mm-wave) generator. In the scheme, two lasers with a 70 GHz frequency interval serve as sources. Then a frequency-quadrupling feed-forward modulation technique is employed to generate two phase correlated sidebands with a 60 GHz interval. The desired sidebands can be selected by using standard optical interleavers. In our work, a 60 GHz mm-wave signal free of phase noise can be achieved. The employed technique can also be extended to frequency 8-tupling.     

A novel optical mm-wave generation scheme based on three parallel Mach-Zehnder modulators

We propose a novel optical mm-wave generation scheme based on three parallel Mach-Zehnder modulators (MZMs) for the first time. First, the scheme is investigated theoretically, which suggests that it can be used for sextupling, 12-tupling, and 18-tupling mm-wave generation. Then simulation results are given, 60 GHz mm-wave is generated from 5 GHz, or 10 GHz RF oscillator based on frequency 12-tupling or sextupling, and 90 GHz mm-wave is generated from 5 GHz RF oscillator based on frequency 18-tupling. The optical sideband suppression ratio (OSSR) and the radio frequency spurious suppression ratio (RFSSR) are analyzed by simulation, in which several non-ideal factors are taken into consideration. Results indicate that all the three mm-wave generation methods are practical and very good performance can be obtained when the extinction ratio of the MZM is 30 dB, even if the extinction ratio of the MZM is 20 dB, the performance is still good, especially for the sextupling mm-wave generation method, whose performance is excellent and insensitive to the extinction ratio of MZM, the non-ideal RF driving voltage and the non-ideal DC bias. At last, we set up a RoF system by simulation to verify the transmission performance of the scheme. The BER performance and eye diagrams are given.     

10 Gb/s optical carrier distributed network with W-band (0.1 THz) short-reach wireless communication system

Millimeter-wave (mm-wave) operated in W-band (75 GHz–0.11 THz) is of particular interests, since this frequency band can carry signals at much higher data rates. We demonstrate a 10 Gb/s optical carrier-distributed network with the wireless communication system. The mm-wave signal at carrier frequency of 0.1 THz is generated by a high speed near-ballistic uni-traveling carrier photodiode (NBUTC-PD) based transmitter (Tx), which is optically excited by optical short pulses. The optical pulse source is produced from a self-developed photonic mm-wave waveform generator (PMWG), which allows spectral line-by-line pulse shaping. Hence these optical pulses have high tolerance to fiber chromatic dispersion. The W-band 10 Gb/s wireless data is transmitted and received via a pair of horn antennas. The received 10 Gb/s data is envelope-detected and then used to drive an optical modulator at the remote antenna unit (RAU) to produce the upstream signal sending back to the central office (CO). 20 km single mode fiber (SMF) error free transmission is achieved. Analysis about the optimum repetition rate of the optical pulse source and the transmission performance of the upstream signal are also performed and discussed.     

An optical mm-wave generation scheme by frequency octupling using a nested MMI

A novel method of a filterless optical millimeter-wave (MMW) signal generation with frequency octupling via a nested multimode interference (MMI) coupler is proposed for Radio-over-fiber systems. By setting the DC bias voltage applied to the central arms of MMI-b and MMI-c accurately, the optical carrier can be completely suppressed. The OSSR can be as high as about 58 dB without optical filter and the radio frequency spurious suppression ratio (RFSSR) exceeds 32 dB, which is the best result as we know. Simulation results suggest that when the generated optical mm-wave signal is transmitted along the standard single-mode fiber, the eye diagram is still opened after being transmitted over a 50 km fiber.     

A multi-channel full-duplex 60-GHz-band radio-over-fiber system

We propose and simulate a novel full-duplex radio-over-fiber system using a single light source at central station (CS). The scheme is employed to generate 60-GHz optical millimeter wave at CS for down-link transmission while the same optical carrier is reused at base station for up-link connection. There is no additional laser source for the upstream data generation in the base station. The bidirectional full-duplex 2.5 Gb/s data are successfully transmitted over 40 km standard single-mode fiber (SMF). The power penalty for the down-link data after transmission over 40 km SMF is less than 0.6 dB, while for the up-link data, the power penalty after transmission over 40 km SMF is neglected. This system shows good performance over long-distance delivery and has important applicable value in high radio frequency (RF) sector and multi-channel full-duplex system.     

Generation and transmission of the double-sideband optical millimeter-wave with signal carried only by optical carrier

In this paper, we have proposed a new scheme to generate double-sideband (DSB) optical millimeter-wave (mm-wave) with signal carried only by optical carrier, and its transmission performance is investigated. The theoretical and numerical results show that the DSB optical mm-wave signal generated by our scheme suffers only from the fading effect, the time shift of the sidebands has little influence on its transmission performance. The signal demodulated from the harmonic photocurrent shows a clear and open eye diagram and has good performance even if the transmission distance is very close to but not just at the fading nodes. The theoretical results are in good agreement with our numerical simulation.     

Bidirectional WDM-PON architecture using a reflective filter and cyclic AWG

We proposed and demonstrated a bidirectional SCM-WDM PON using a reflective filter and cyclic AWG where up/downlink data could be provided using a single optical source. In the proposed scheme, the signal for downstream was modulated by a single CW laser diode and remodulated in the optical network unit as an upstream, the proposed WDM-PON scheme can offer the SCM signal for broadcasting service. In this paper, 1 Gb/s signals both for up- and downstream were demonstrated in 10 km bidirectional optical fiber link.     

10 Gb/s TDM passive optical networks using four wavelengths multiplexed channels

We propose a new architecture for 10 Gb/s upstream traffic in TDM-PON using externally injection-locked Fabry-Perot laser diodes (FP-LDs) in each optical network unit (ONU). Four directly modulated 2.5 Gb/s FP-LDs were injection-locked by continuous wave (CW) carriers distributed from the optical line terminal (OLT). Hence, a total of 10 Gb/s upstream traffic can be achieved. Experimental results show negligible power penalty at a transmission of 25 km standard single mode fiber (SMF) without dispersion compensation. The performance of the injection-locked FP-LD is also studied.     

The transmission performance degradation of the optical millimeter-wave signals by fiber chromatic dispersion

The influence of the fiber chromatic dispersion on double sideband (DSB), optical carrier suppression (OCS), and single sideband (SSB) optical mm-wave signals is investigated based on the Taylor expansion of the propagation constant and is verified by simulation. According to our theoretical results, the fading effect suppresses the signal power of the DSB optical mm-wave periodically in a cosine-like pattern, and it can be described by the zero-order Taylor expansion of the propagation constant. For the optical mm-wave with the signal modulated on two or more tones, the bit pulses of the mm-wave signal are distorted by the dispersion-inducing bit walk-off effect between tones, which is expressed by the first-order Taylor expansion of the propagation constant. Moreover, as the signal rate and the transmission distance are increased further, higher-order Taylor expansion of the propagation constant still degrades the optical mm-wave signal even if both the fading effect and the bit walk-off effect are eliminated completely. The distortion of the signal pulses of SSB optical mm-wave is derived based on the second-order Taylor expansion of the propagation constant. This degradation is verified by the simulation with the eye diagram evolution of the SSB optical mm-wave signal.