大气压氩气介质阻挡辉光放电的一维仿真研究

为了研究氩气(Ar)中介质阻挡大气压辉光放电(APGD)的放电机理, 通过建立一个一维的多粒子自洽耦合流体模型, 采用有限元方法进行数值计算, 得到了气体间隙压降、介质表面电荷密度、放电电流密度随时间的周期变化波形, 以及电子、离子、亚稳态粒子密度和空间电场强度的时空分布. 仿真计算结果表明：介质表面积聚的电荷对于放电的过程的起始及熄灭具有重要作用;当增大外施电压时, 放电击穿时刻提前, 放电电流密度和介质表面电荷密度峰值增大, 表明放电过程更加剧烈;随着阻挡介质相对介电常数的增大, 放电电流密度也随之增大. 各粒子密度及电场的时空分布表明放电过程在外施电压半个周期中只有一次放电, 且存在明显的阴极位降区、负辉区、等离子体正柱区等辉光放电的典型区域, 为大气压辉光放电(APGD).     

针-板DBD微流注与微辉光交替生成的机理研究

在介质阻挡放电体系中产生辉光放电可以有效的提高放电体系产生高能电子的性能, 为等离子体化学反应提供更加丰富的活性粒子.本文对针-板介质阻挡放电体系下的放电模式进行了研究,实验发现放电正负半周期表现出不同的放电模式, 激励电压为3 kV时放电正负半周期分别为微流注放电和电晕放电(或者Trichel脉冲放电),激励电压为6 kV时放电正负半周期分别为微流注放电和微辉光放电.微辉光放电形貌具有与典型辉光放电相同的分层次放电结构, 分析了激励电压6 kV时的放电过程,认为足够强的阴极电场强度和裸露针状电极形成的有效的二次电子发射过程是形成微辉光放电的主要因素,绝缘介质层的存在避免了微辉光放电向弧光放电过渡.     

介质阻挡放电点燃大气压直流均匀放电的光谱研究

由于大气压均匀放电等离子体在工业领域具有广泛的应用前景,为了获得大尺寸的大气压均匀等离子体,采用氩气作为工作气体,在大气压空气环境中利用同轴介质阻挡放电点燃了针-板电极间的大气隙(气隙宽度达到5 cm)直流均匀放电。研究发现,同轴介质阻挡放电能够有效降低针-板电极间的击穿电压。该均匀放电由等离子体柱、等离子体羽、阴极暗区和阴极辉区组成。其中等离子体柱和阴极辉区都是连续放电。而等离子体羽不同位置的放电是不同时的。事实上,等离子体羽放电是由从阴极向着等离子体柱移动的发光光层(即等离子体子弹)叠加而成。利用电学方法测量了放电的伏安特性曲线,发现其与低气压正常辉光放电类似,均具有负斜率。采集了放电的发射光谱,发现存在N₂第二正带系、氩原子和氧原子谱线。通过Boltzmann plot方法对放电等离子体电子激发温度进行了空间分辨测量,发现等离子体柱的电子激发温度比等离子体羽的电子激发温度低。通过分析放电机制,对以上现象进行了定性解释。这些研究结果对大气压均匀放电等离子体源的研制和工业应用具有重要意义。     

大气压氩气介质阻挡放电中的四边形斑图和六边形斑图

在大气压氩气介质阻挡放电中，研究了斑图形成随放电条件的变化.观察到随电压的增加，斑图经历六边形—四边形—具有辉光背景的四边形—具有辉光背景的六边形的转变过程.其空间波长与放电丝密度也随之改变.在一定的放电条件下，斑图涌现出辉光背景，此时空间波长与放电丝密度保持不变，但放电丝每半周期放电脉冲数由一次变为两次. 关键词： 介质阻挡放电 四边形斑图 六边形斑图 空间波长     

大气压氩气环境下体积介质阻挡放电光谱特性

通过介质阻挡放电产生的等离子体可与燃料中的烃类分子发生碰撞裂解反应,将燃料分子裂解生成更容易起爆的氢气和小分子烃类,能有效改善液体燃料连续旋转爆震发动机的起爆性能。该研究在真空仓中开展体积介质阻挡放电的丝状放电光谱测试,分析了大气压氩气环境下体积介质阻挡放电的电子激发温度和电子密度随加载电压的变化规律。丝状放电的电子激发温度通过波尔兹曼斜率法计算,电子密度采用斯塔克展宽法计算。发现发射谱线均由氩原子4p-4s能级跃迁产生;各谱线强度随加载电压的提高均呈上升趋势,且与电压基本呈线性关系;对于大气压丝状放电,加载电压对电子激发温度和电子密度没有明显影响作用,加载电压12.5～14.5 kV范围内,电子激发温度稳定在3 400 K附近,电子密度在1025 m-3量级。     

介质阻挡放电六边形斑图稳定过程的光谱研究

采用发射光谱法,首次研究了等离子体参数及激发状态对介质阻挡放电六边形斑图稳定性的影响。在氩气/空气混合气体的介质阻挡放电中,随着电压的升高,放电丝直径增大,六边形斑图逐渐稳定,同时放电颜色由紫色逐渐变为灰白色,说明其等离子体状态及参数可能发生了变化。测量了六边形斑图放电过程中氮分子谱线和氩原子谱线相对于氩原子763.51 nm的相对强度、分子振动温度和电子激发温度随外加电压的变化。结果发现：氮分子谱线相对强度随电压增加而降低,氩原子谱线相对强度却升高;分子振动温度与电子激发温度均随电压增加而增大。这些现象表明：随着电压增大,电子能量增加。由此,氩原子激发增多,放电丝直径增大,介质表面上沉积的壁电荷面积增大,放电丝之间的相互作用增强,六边形斑图趋于稳定。     

Characteristics of a large gap uniform discharge excited by DC voltage at atmospheric pressure

A large-gap uniform discharge is ignited by a coaxial dielectric barrier discharge and burns between a needle anode and a plate cathode under a low sustaining voltage by feeding with flowing argon. The basic aspects of the large-gap uniform discharge are investigated by optical and spectroscopic methods. From the discharge images, it can be found that this discharge has similar regions with glow discharge at low pressure except a plasma plume region. Light emission signals from the discharge indicate that the plasma column is invariant with time, while there are some stochastic pulses in the plasma plume region. The optical emission spectra scanning from 300 nm to 800 nm are used to calculate the excited electron temperature and vibrational temperature of the large-gap uniform discharge. It has been found that the excited electron temperature almost keeps constant and the vibrational temperature increases with increasing discharge current.Both of them decreases with increasing gas flow rate.     

微隙介质阻挡放电装置中的空气均匀放电光谱特性

大气压空气中介质阻挡均匀放电产生的等离子体在工业领域具有广阔的应用前景,为研究其产生条件及机理,利用微间隙介质阻挡放电装置,在大气压空气中实现了均匀放电。电学实验结果表明,低电压时电流波形在电压每半个周期存在若干个脉冲宽度很小的脉冲,肉眼观察到大量的微放电丝,随着外加电压增加,放电功率逐渐增加,放电空间内微放细丝增多。当电压增大到9.2 kV时,电流波形在电压每半个周期只存在一个宽度较大(约5.5 μs)强度较强的脉冲,观察不到微放电丝,微放电最终扩展叠加形成均匀放电。采集了光谱范围为330～420 nm的发射光谱,氮分子第二正带系337.1 nm的谱线强度明显比氮分子离子第一负带系391.4 nm的强。将337.1 nm谱线的强度归一,391.4 nm谱线的强度即反应了电子平均能量的大小,同时拟合计算了反映分子内部能量的氮分子振动温度。结果表明电子平均能量和分子内部能量都随外加电压的增加而降低。表明放电空间电场能量较低时不容易形成丝状放电,均匀放电模式中电子平均能量比微放电丝放电模式中的低。这些结果对于空气中介质阻挡均匀放电在工业应用方面具有一定的指导意义。     

大气压下绝缘毛细管内等离子体放电及其特性研究

在石英毛细管内利用两个边缘锋利的中空针型电极间的放电形成了63 cm长的大气压弧光等离子体.通过记录放电图片和测量电流-电压特征波形及伏安特性曲线的方法对管内等离子体从反常辉光状态过渡至超长弧光状态的过程做了细致的研究,发现管内等离子体在弧光状态下的电子密度不低于10¹⁴ cm^-3.另外,还进一步考察了两电极的间距和电源工作频率对放电伏安特性的影响以及通过发射光谱法测得的等离子体气体温度随外加电压的变化规律.当活性气体(氧气)按一定比例混合到氩等离子体中时,通过 关键词： 大气压等离子体 反常辉光放电 弧光放电 发射光谱     

不同电极结构下介质阻挡放电电离特征的试验研究

由于具有工作气压高、放电均匀等特点,大气压介质阻挡放电成为近年来非平衡等离子体领域研究的主要技术。电极结构是电离特性的主要影响因素之一,因此,通过电极结构优化来改善电离特性,对等离子体放电设备的应用领域拓展及性能优化至关重要。为改善大气压介质阻挡放电的电离特性,产生高活性、高均匀性的低温等离子体,基于自主设计的同轴介质阻挡放电装置进行了不同电极结构的电离试验及参数诊断;在一个标准大气压、放电频率11.4 kHz、放电峰值电压5.4～13.4 kV条件下进行了氩气电离试验;采用原子发射光谱法（AES）对氩等离子体谱线的激发、分光进行了检测分析;研究了螺纹电极、齿状电极、圆柱电极放电的特征光谱参数及外施电压对介质阻挡放电特征参数的影响。结果表明,齿状电极放电所形成等离子体的放电强度更大且放电效果显著,电子平均能量利用率低,电子激励温度弱于圆柱电极;圆柱电极放电强度较弱,但易形成大面积均匀性等离子体;大气压环境下电子激励温度不因外源电压的升高而单调递加,这表明通道内微放电的主要特征并不依赖于外施电压的供给,而是取决于电极结构、气体组份、气体压强;增大外施电压仅能增加单位时间内微放电的数量,经整合电子激励温度可达3 500 K,符合典型的低温等离子体特征。     

介质阻挡均匀大气压辉光放电数值模拟研究

通过数值求解一维电子、离子连续性方程和动量方程，以及电流连续性方程，计算了氦气介 质阻挡大气压辉光放电电子、离子密度和电场在放电空间的时空分布，以及放电电流密度和 绝缘介质板充电电荷密度随时间的变化. 分析讨论所加电压频率、幅值及介质板性质等对均 匀大气压辉光放电性质的影响. 当外加电压频率足够高时，大量离子被俘获在放电空间，空 间电荷场又引起足够多的电子滞留在放电空间. 这些种子电子使得在大气压下发生汤森放电 ，放电空间结构类似于低气压辉光放电，即存在明显的阴极位降区、负辉区、法拉第暗区和 等离子体正柱 关键词： 大气压辉光放电 介质阻挡 数值模拟 等离子体     

Design and performance of Yb/ZnS/C Schottky barriers

In this work, ZnS thin films are deposited onto glass and transparent ytterbium substrates under vacuum pressure of 10^?5 mbar. The effects of the Yb substrate on the structural, mechanical, optical, dielectric and electrical performance of the ZnS are explored by means of the energy dispersion X-ray analyzer, X-ray diffraction, UV–VIS spectroscopy, current-voltage characteristics and impedance spectroscopy techniques. The techniques allowed determining the lattice parameters, the grain size, the degree of orientation, the microstrain, the dislocation density, the optical and the excitonic gaps, the energy band offsets and the dielectric resonance and dispersion. The (111) oriented planes of glass/ZnS and Yb/ZnS exhibited 2.06% lattice mismatch between Yb and ZnS and degree of orientation values of 63% and 51.6%, respectively. The interfacing of the ZnS with Yb shrunk the energy band gap of ZnS by 0.50 eV. On the other hand, the electrical analysis on the Yb/ZnS/C Schottky device has revealed a rectification ratio of 3.48 × 10⁴ at a biasing voltage of 0.30 V. The barrier height and ideality factor was also determined. Moreover, the impedance spectroscopy analysis have shown that the Yb/ZnS/C device is very attractive for use as varactor devices of wide tunability. The device could also be employed as microwave resonator above 1337 MHz.     

Mode transition in homogenous dielectric barrier discharge in argon at atmospheric pressure

The influence of driving frequency on the discharge regime of a homogenous dielectric barrier discharge in argon at atmospheric pressure is studied through a one-dimensional self-consistent fluid model. The simulation results show that the discharge exhibits five notable discharge modes, namely the Townsend mode, stable glow mode, chaotic mode, asymmetric glow, and multiple period glow mode in a broad frequency range. The transition mechanisms of these modes should be attributed to the competition between the applied voltage and the memory voltage induced by the surface charges.     

Spatial Uniformity of Atmospheric Pressure Discharges: A Simulation Study

Spatial uniformity is important in most applications of dielectric barrier discharges operating at atmospheric pressure. However, such uniformity is not easily achieved. Under many conditions, a filamentary structure usually develops. In this paper, we employ a two‐dimensional self‐consistent fluid model to explore the influence of several factors on the evolution of spatial structure of dielectric barrier discharges. In particular, we contrast the behavior of discharges in pure helium and He‐N₂ gas mixture, which represent the reduction in breakdown voltage of gas during the evolvement of uniform glow discharge plasma. The transformation from filamentary to uniform mode of discharge plasma is analyzed by the phenomenon of coalescence of filaments and we investigate the effect of several external discharge parameters, such as driving frequency and effect of overvoltage, and the dielectric constant of the barrier material for the uniform and filamentary discharge plasmas. This simulation study is useful to describe the spatio‐temporal profiles of electron density in different phases of the filamentary, uniform Townsend and glow discharge regimes under various constraints. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Measurement of atomic hydrogen density in non-thermal H<Subscript>2</Subscript> plasmas via threshold ionisation-molecular beam mass spectrometry

Determinations of radical density are essential to investigate the physical-chemical processes in plasmas and setup the related theoretical models. This paper presents the experimental measurement of atomic hydrogen near grounded electrode in dielectric barrier discharge medium-pressure hydrogen plasma via threshold ionisation-molecular beam mass spectrometry. After investigating the possible influences from parent molecules in excited states, background component and space-charge, evolution of atomic hydrogen density as functions of discharge parameters are investigated utilising the signal of H₂ molecule beam as the reference. At fixed gas pressure of 6.0 torr and a discharge voltage of 24 kV, atomic hydrogen density increases monotonously from 1.1×10¹⁴ to 2.0×10¹⁵ cm^-3 as the discharge frequency increases from 9 to 26 kHz. Similarly the rising discharge voltage also lead to enhancement of atomic hydrogen density.     

Simulation of radio-frequency atmospheric pressure glow discharge in γ mode

The existence of two diffe1：ent discharge modes has been verified in an rf （radio-frequency） atmospheric pressure glow discharge （APGD） by Shi [J. Appl. Phys. 97, 023306 （2005）]. In the first mode, referred to as a mode, the discharge current density is relatively low and the bulk plasma electrons acquire the energy due to the sheath expansion. In the second mode, termed γ mode, the discharge current density is relatively high, the secondary electrons emitted by cathodc under ion bombardment in the cathode sheath region play an important role in sustaining the discharge. In this paper, a one-dimensional self-consistent fluid model for rf APGDs is used to simulate the discharge mechanisms in the mode in helium discharge between two parallel metallic planar electrodes. The results show that as the applied voltage increases, the discharge current becomes greater and the plasma density correspondingly increases, consequentially the discharge transits from the a mode into the γ mode. The high collisionality of the APGD plasma results in significant drop of discharge potential across the sheath region, and the electron Joule heating and the electron collisional energy loss reach their maxima in the region. The validity of the simulation is checked with the available experimental and numerical data.     

直流大气压辉光放电高能电子密度的空间分布

利用针阴极和水阳极,在6 mm的空气隙产生了大气压空气辉光放电。该大气压辉光放电具有明显的负辉区、正柱区和阳极辉区等明亮的发光区。通过研究放电的电压电流特性,发现该放电处于亚辉光放电到正常辉光放电阶段。由于氮分子第二正带系337.1 nm的光谱强度反映高能电子密度,对337.1 nm谱线的强度进行了空间分辨测量。结果发现高能电子在针尖附近密度最大,而其他区域相差不多。随电压升高,高能电子密度减少。增大限流电阻,高能电子密度也减少。氧原子对杀菌消毒具有重要作用,利用发射光谱法对氧原子谱线强度的空间分布进行了测量,发现氧原子谱线强度与高能电子的空间分布及其随参数的变化关系一致。     

Discharge Operation Mode Manipulation of Radio Frequency Atmospheric Pressure Glow Discharges in Argon

Stable operation of radio frequency atmospheric glow discharges is widely desired by most processing applications for their conveniency and feasibility, many of which have been addressed with the noble gas of helium and low discharge current density in stable operation regime of α mode. Here, the operation mode manipulation of rf atmospheric pressure glow discharge in argon is investigated using a one‐dimensional self‐consistent modeling approach. Stable operation regime of α mode is found to expand with rinsing excitation frequency and reducing discharge gap distance. The sheath characteristics in terms of sheath voltage and sheath thickness are given to explain the of α ‐γ mode transition. Furthermore, stable operation of discharge in γ mode is proposed tobe achieved by introducing dielectric barriers, which is indicated by monotonously growing of applied voltage with discharge current density (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

大气压等离子体炬电子密度的光谱诊断

利用空心针-板放电装置产生了大气压等离子体炬,采用光谱法测量了其内部及表面的电子密度. 向空心针中通入氩气,在大气环境中产生了长度为1cm的等离子体炬.实验分别测量了Hα谱线和ArⅠ(696.54nm)谱线,通过反卷积方法分离出其相应的Stark展宽,并由此计算了电子密度.结果发现,采用Hα谱线和ArⅠ(696.54nm)谱线Stark展宽计算得到的等离子体的电子密度分别为1.0×10¹⁵cm^－3和3.78×10^{15关键词： 等离子体炬 电子密度 气体温度 Stark展宽}     

Development of exploding wire ion source for intense pulsed heavy ion beam accelerator

A Novel exploding wire type ion source device is proposed as a metallic ion source of intense pulsed heavy ion beam (PHIB) accelerator. In the device, multiple shot operations are realized without breaking the vacuum. The basic characteristics of the device are evaluated experimentally with an aluminum wire of diameter 0.2 mm and length 25 mm. A capacitor bank of capacitance 3 μF and a charging voltage of 30 kV was used, and the wire was successfully exploded by a discharge current of 15 kA with a rise time of 5.3 μs. Plasma flux of ion current density around 70 A/cm² was obtained at 150 mm downstream from the device. The drift velocity of ions evaluated by a time-of-flight method was 2.7×10⁴ m/ s, which corresponds to the kinetic energy of 100 eV for aluminum ions. From the measurement of the ion current density distribution, the ion flow is found to be concentrated toward the direction where the ion acceleration gap is placed. From the experiment, the device is found to be acceptable for applying the PHIB accelerator.