波分复用串联的布里渊散射分布式光纤传感器

在一定分辨率和响应时间要求下，应用波分复用技术来串联布里渊散射分布式光纤传感器，解决了同时进行传感和通信存在的信号干扰.具体是采用波分复用来隔离传感光信号与通信光信号，同时应用光相干外差接收来分离传感与通信之间的电信号频谱.实现了两台布里渊散射分布式光纤传感器之间的串联，单台传感器的传感距离为25 km，串联后达到50 km.     

分立式与分布式光纤传感关键技术研究进展

光纤传感技术已广泛应用于航空航天、石油化工、电子电力、土木工程、生物医药等领域,其技术形式主要体现为分立式和分布式.分立式光纤传感技术利用光纤敏感器件作为传感器来感知被测参量的变化,光纤作为光信号的传输通道连接光纤传感器及后端的解调装置;分布式光纤传感系统基于光纤瑞利散射、拉曼散射或布里渊散射等光学效应,利用光纤本身作为传感器,可对沿途的光信号进行大范围、长距离传感.本文介绍了分立式与分布式光纤传感中主要关键技术的研究进展,并对未来的研究和发展方向进行了探讨.     

分布式光纤布里渊散射温度传感实验系统

提出一种基于布里渊光时域反射计法的分布式光纤布里渊散射温度传感系统.光源采用窄谱半导体激光器.声光调制器将光源调制成窄脉冲,并由高增益光纤放大器放大,产生高功率光脉冲信号,提高了自发布里渊散射信号的强度.采用双通马赫-曾德干涉仪将布里渊散射从瑞利散射中分离出来,在一段4.25 km长的光纤上进行分布式温度传感的实验研究.双通马赫-曾德干涉仪对瑞利散射进行了很好的抑制,得到了比较纯净的随温度变化的布里渊散射信号.     

一种基于暗脉冲光布里渊时域分析仪的延长传感距离的方法

基于暗脉冲的布里渊时域分析仪系统中泵浦光和探测光的功率较高,相互作用强烈,严重限制了系统的有效传感距离。而现有的系统众多采用利用多段具有不同布里渊散射频率的光纤相互连接延长传感距离的方法,降低每段光纤上的受激布里渊散射效应,延长有效传感距离,但这种方案会增加的系统的复杂度,影响实际应用.本文提出一种简单的暗脉冲光布里渊时域分析仪的结构,可在满足高空间分辨率的条件下,有效的延长系统的传感距离,取代通常的利用多段具有不同布里渊散射频率的光纤相互连接延长传感距离的方法.利用基于光抑制载波的技术,产生具有两个边带的斯托克斯光.斯托克斯光的两个边带和泵浦光相互作用,同时激发布里渊散射增益和衰减效应,在接收端利用两者接收信号的差,可抵消原有暗脉冲泵浦信号中准连续光对传感距离的影响,从而有效地延长系统的传感距离,并利用数值仿真的方法验证了此方法的有效性.     

光纤移频分布式布里渊光纤传感技术

提出了一种利用布里渊光纤环形腔移频技术实现分布式光纤布里渊传感的方法.该方法基于布里渊光时域分析法原理,将一束单纵模运转激光器输出的激光分为两束;一束光入射布里渊光纤环形腔中产生窄线宽的受激布里渊散射光作为斯托克斯光,另一束光经过低频相位调制后作为泵浦光;斯托克斯光和泵浦光分别相向入射进入传感光纤,通过测量布里渊谱得到...     

基于布里渊散射的分布式光纤传感技术

基于布里渊散射的分布式光纤传感技术是目前国内外研究的热点。其中基于时域定位的布里渊分布式光纤传感技术主要分为布里渊光时域反射和布里渊光时域分析两种。国内对基于布里渊光时域反射技术的分布式光纤传感技术的研究报道比较多。介绍了基于布里渊光时域分析技术的分布式光纤传感技术的研究现状,并对基于时域定位的两种传感技术进行了分析对比。总结了布里渊散射分布式光纤传感技术实用化存在的问题及可能的解决方法,指出了该传感技术进一步的发展方向。     

光纤移频分布式布里渊光纤传感技术

提出了一种利用布里渊光纤环形腔移频技术实现分布式光纤布里渊传感的方法.该方法基于布里渊光时域分析法原理,将一束单纵模运转激光器输出的激光分为两束|一束光入射布里渊光纤环形腔中产生窄线宽的受激布里渊散射光作为斯托克斯光,另一束光经过低频相位调制后作为泵浦光|斯托克斯光和泵浦光分别相向入射进入传感光纤,通过测量布里渊谱得到光纤温度或应变.利用该方法可将十几GHz的微波频率转化为兆赫信号频率进行探测处理,仅需一台激光器,因此系统结构简单、成本低,还可减小激光器频率波动对测量准确度的影响.实验验证了该方法的可行性.     

拉曼放大布里渊光时域分析系统非局域效应

应用包含探测光、布里渊泵浦光及拉曼泵浦光相互作用理论模型,数值分析了基于拉曼放大的长距离布里渊光时域分析仪非局域化特性。结果表明:非局域化随探测光及拉曼泵浦功率增加而恶化;通过频分复用(将具有不同布里渊频移的光纤拼接)及时分复用技术(同时对布里渊泵浦及探测光进行脉冲调制),可有效缩短布里渊泵浦与探测光的作用距离,达到较理想的抑制非局域效应结果。     

S波段光纤拉曼放大器中级联受激布里渊散射串扰的实验研究

研究了光纤激光器前向抽运的S波段分布式光纤拉曼放大器中级联的受激布里渊散射(SBS)串扰现象。用窄光谱带宽(<100MHz)的可调谐激光二极管作为信号源,通过S波段分布式光纤拉曼放大器,当被放大的信号功率超过单模光纤受激布里渊散射的阈值时,出现了前向受激布里渊散射,这是传导声波布里渊散射在光纤放大器中放大的现象。随着拉曼放大器抽运功率的提高,在斯托克斯区,出现了两阶受激布里渊散射线,在实验中观测到偶数阶的受激布里渊散射谱线功率大于奇数阶的布里渊一瑞利散射线。当进一步增加拉曼放大器的抽运功率,出现了前向级联的多阶受激布里渊散射现象,拉曼放大器的增益下降,被放大的信号功率转换为受激布里渊散射,噪声变大。受激布里渊散射的串扰破坏了拉曼放大器的特性,使拉曼放大器无法在密集波分复用光纤传输系统中使用,因此需要严格地控制入纤的信号功率和放大器的抽运功率。在实验中还观测到在光纤拉曼放大器中被放大的信号光和受激布里渊散射线两侧的伴线。     

Distributed analysis of forward stimulated Brillouin scattering for acoustic impedance sensing by extraction of a 2nd-order local spectrum

Distributed fiber sensors based on forward stimulated Brillouin scattering (F-SBS) have attracted special attention because of their capability to detect the acoustic impedance of liquid material outside fiber. However, the reported results were based on the extraction of a 1st-order local spectrum, causing the sensing distance to be restricted by pump depletion. Here, a novel post-processing technique was proposed for distributed acoustic impedance sensing by extracting the 2nd-order local spectrum, which is beneficial for improving the sensing signal-to-noise ratio (SNR) significantly, since its pulse energy penetrates into the fiber more deeply. As a proof-of-concept, distributed acoustic impedance sensing along ～1630 m fiber under moderate spatial resolution of ～20 m was demonstrated.     

分布式光纤温度压力传感器设计

为了实现油田井下温度压力的全分布式测量,提出了一种基于光纤散射原理的分布式温度压力测量方法。该方法通过对普通光纤进行封装设计,制作成传感光纤。由于光纤传感器周围流体的温度和压力会对传感光纤内的散射光产生调制作用,通过光纤解调仪解调出光纤拉曼散射参数和布里渊散射频移就能够实现温度和压力的实时在线测量。实验结果表明:设计的分布式光纤温度压力传感器可以实现的温度测量分辨率为0.1 ℃,压力测量分辨率为0.07 MPa。基本满足油田井下温度压力测量的全分布式、实时在线、可靠性高、精度高、抗干扰能力强等要求。     

基于双向拉曼放大的布里渊光时域分析系统

报道了一种基于双向拉曼放大的布里渊光时域分析系统(Brillouin optical time domain analyzer,BOTDA).利用双向拉曼抽运对信号光进行拉曼放大以补偿光纤损耗及布里渊抽运波的消耗,从而使光纤后端的测量分辨率得到改善,测量分辨率在整段传感光纤趋于一致,同时避免了调制不稳定性引起的频谱扩展,克服了传统BOTDA存在的信号强度指数下降的弊端,使传感精度得到进一步提高.实验实现了50 km传感距离, 温度分辨率达0.6 ℃,空间分辨率为50 m.实验测量并分析了基于双向拉曼放大的BOTDA信噪比和光功率分布特性. 关键词： 分布式光纤传感 受激拉曼放大 布里渊增益 布里渊光时域分析     

Stimulated Brillouin scattering frequency-domain analysis in a single-mode optical fiber for distributed sensing

A numerical and experimental analysis of the stimulated Brillouin scattering in a single-mode optical fiber for distributed sensing applications is carried out in the frequency domain. The theoretical model describing the Brillouin interaction is solved by taking into account the temporal dynamics of the acoustic wave that is involved. The simulations and the experimental results reveal the role played by the ac component of the acoustic wave, which is responsible for significant changes of the small-signal stimulated Brillouin scattering transfer function that occur when the modulation frequency rises above the natural Brillouin gain spectrum linewidth. One should take these effects into account to perform accurate signal processing of frequency-domain signals in high-resolution distributed sensing applications.     

Optical coherent detection Brillouin distributed optical fiber sensor based on orthogonal polarization diversity reception

In Brillouin distributed optical fiber sensor, using optical coherent detection to detect Brillouin scattering optical signal is a good method, but there exists the polarization correlated detection problem. A novel detecting scheme is presented and demonstrated experimentally, which adopts orthogonal polarization diversity reception to resolve the polarization correlated detection problem. A laser is used as pump and reference light sources, a microwave electric-optical modulator (EOM) is adopted to produce frequency shift reference light, a polarization controller is used to control the polarization of the reference light which is changed into two orthogonal polarization for two adjacent acquisition periods. The Brillouin scattering light is coherently detected with the reference light, and the Brillouin scattering optical signal is taken out based on Brillouin frequency shift. After electronic processing, better Brillouin distributed sensing signal is obtained. A 25-km Brillouin distributed optical fiber sensor is achieved.     

A new method to eliminate the influence of the backward defect infection and the position-dependent of the coefficient on distributed Brillouin fiber sensor

Two theoretical problems associated with the measurement of temperature or strain from the normalized power of Brillouin signal in a distributed fiber sensor are studied. One problem is the position-dependent of the coefficient relating the Brillouin power to the local temperature or strain. The other problem is the backward infection of the defect (local temperature or strain change). These two problems will degrade the measurement accuracy of a distributed Brillouin fiber sensor by changing the distribution of pump power. To eliminate these two problems, new reference functions are proposed to normalize the Brillouin signal. Simulation results by using fourth-order Runge-Kutta algorithm show that these new reference functions can eliminate the influence of these two problems on distributed Brillouin fiber sensor.     

毫米级高分辨率的混沌激光分布式光纤测温技术

近年来,随着分布式光纤传感技术在各大基础设施健康监测领域的广泛应用,人们对能够实现毫米量级精准定位和监测技术的需求日益增长.本文提出了一种基于宽线宽混沌激光的高分辨率分布式光纤测温技术.实验通过改变光反馈混沌源的偏振匹配态和反馈强度等外部参数,产生了–3 dB线宽约为7.5 GHz的宽线宽混沌激光,并在300 m传感光纤实现了空间分辨率为7.05 mm的分布式温度测量.同时,为了抑制光源线宽增加造成的布里渊增益谱恶化,在泵浦路中引入了时间门控技术,其中经脉冲调制后的泵浦光峰值功率提高了约9.5 dB,同时脉冲调制使混沌互相关锁定于脉冲持续时间内,从而布里渊增益谱的信号背景噪声比由约2.28 dB提升为4.55 dB,最终实现了空间分辨率为3.12 mm的分布式温度测量.     

Threshold features of a Brillouin Stokes comb generated in a distributed fiber Raman amplifier

We study threshold features of a Brillouin-shifted Stokes comb generated in a distributed fiber Raman amplifier. When the input power of Brillouin pump is linearly increased in high Raman gain, the first Stokes wave grows exponentially at much lower threshold power and then experiences an appreciable power decrease in the vicinity of the Brillouin comb's threshold. This power reduction of the first Brillouin Stokes, which we did not see mentioned in previous reports, was caused by a power transfer to higher-order lines and initiated Brillouin comb generation. Moreover, the effects of Raman pump power and pumping direction on the threshold of a Brillouin comb are investigated.     

Simultaneous temperature and strain measurement with combined spontaneous Raman and Brillouin scattering

We report on a novel method for simultaneous distributed measurement of temperature and strain based on spatially resolving both spontaneous Raman and Brillouin backscattered anti-Stokes signals. The magnitude of the intensity of the anti-Stokes Raman signal permits the determination of the temperature. The Brillouin frequency shift is dependent on both the temperature and the strain of the fiber; once the temperature has been determined from the Raman signal, the strain can then be computed from the frequency measurement of the Brillouin signal.     

Dual-source distributed optical fiber sensor for simultaneous temperature and strain measurements

A dual-source distributed optical fiber sensor system with combined Raman and Brillouin scatterings is designed for simultaneous temperature and strain measurements. The optimal Raman and Brillouin signals can be separately obtained by adjusting the powers of the two sources using an optical switch. The temperature and strain can be determined by processing the optimal Raman and Brillouin signals. The experimental result shows that 1.7 ?C temperature resolution and 60-με strain resolution can be achieved at a 24.7-km distance.     

光纤中拉曼散射回波超高灵敏度探测技术研究

与布里渊散射不同,石英光纤中斯托克斯拉曼散射与光纤所受应力无关,只是绝对温度的函数,而且其拉曼频移为1.395×1013 Hz, 比布里渊散射易于提取,作为分布式光纤温度传感器的传感信号有一定的优势,但斯托克斯拉曼散射信号比布里渊弱,其峰值功率在APD中产生的光电流在nA级,低于APD的噪声电流,经光电转换后信号的信噪比小于1,傅里叶变换以及小波变换都无法有效地处理这类信号。通过对斯托克斯拉曼散射信号进行特征分析后,采用累加与小波降噪的综合方法提取该信号,实现在APD噪声电流以下的超灵敏度探测,达到每度0.104 nA的温度灵敏度,低于本系统所有APD噪声电流2.3 nA的1个数量级。