Electromagnetic radiation and variations in the conductivity of muscovite specimens during dehydration

The authors give experimental results on the measurement of electromagnetic radiation and electrical conductivity of muscovite specimens during heating or cooling in the temperature range from 20 to 600°C. It was established that at some temperatures there were variations in the electrical conductivity with the attendant onset of pulsed electromagnetic radiation in the radio-frequency range from 247.5 kHz to 35.8 MHz. The oscillations in the conductivity and the maximum intensity of electromagnetic radiation coincide with the boiling points of weakly bound water at about 100°C, the electrical activity of centers on the surface of micas (20–450°C), the temperatures of crystallization of muscovite in a hydrothermal process from 480 to 160°C, and phase transitions at 550–590°C. The electromagnetic radiation is probably due to fluctuations in the defects in the mineral under thermal excitation and adhesion processes as a result of dehydration of the muscovite.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 1, pp. 27–33.     

35 GHz dielectric resonator stabilised gunn oscillator

A 35 GHz dielectric resonator oscillator(DRO) using GaAs Gunn diode in microstrip configuration has been designed and developed. The oscillator, with an integral waveguide-to-microstrip transition, delivered an output greater than 18 dBm. Phase noise of the oscillator is found to be better than –80 dBc/Hz at 100 KHz away from the carrier. A frequency drift of about ±25 MHz has been observed over the temperature range from –10 °C to 50 °C.     

Development of nanocrystalline Mn-Zn ferrites for high frequency transformer applications

Microwave-Hydrothermal (M-H) method has been successfully used for the synthesis of nanocrystalline Mn-Zn ferrites which are used for high-frequency applications. As synthesized powders were characterized using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The nanopowders were annealed at 600 °C/20 min using the microwave sintering method. The frequency dependence of dielectric constant (ε′) was measured in the range of 10 Hz-1.3 GHz and initial permeability (μ_i) was measured in the range of 10 Hz-1 MHz. The total power loss (P_t) was measured on the annealed samples at 100 kHz and 200 mT condition. Conductor-embedded-ferrite transformers were fabricated and output power (P_o), efficiency (η) and temperature rise (ΔT) were measured at sinusoidal voltage of 25 V at 1 MHz. The transformer efficiency (η) was found to be high and surface rise of temperature (ΔT) is very low.     

AC magnetic susceptibility at medium frequencies suggests a paramagnetic behavior of pure water

The AC magnetic susceptibility of water is studied in the frequency range of 1 kHz-1 MHz at a low magnetic field. The results show a paramagnetic behavior between 500 kHz and 1 MHz for samples at 37 °C and 25 °C, which is surprising considering that water is believed to be diamagnetic. AC magnetic susceptibilities for ice and different salt solutions were investigated as well: in such cases the susceptibility is always negative and therefore, such samples remain diamagnetic.     

Mutual inductance bridge for magnetic relaxation measurements at low temperatures

An apparatus using a mutual inductance bridge has been designed to measure real and imaginary parts of the magnetic ac susceptibility simultaneously in the frequency range from 1 Hz to 230 kHz at helium temperatures. From 230 kHz up to 3 MHz the real part can be determined. The susceptibility as a function of temperature or external magnetic field at constant frequency may be measured. In addition, frequency sweeps can be performed with temperature and magnetic field held constant. The experiment is controlled by an on-line computer.     

A study of ultrasonic velocity and attenuation on nanocystalline MgCuZn ferrites

The nanocrystalline MgCuZn ferrites with particle size (∼30 nm) have been synthesized by microwave-hydrothermal (M-H) method at 160 °C/45 min. The powders were densified at 750-900 °C/30 min using microwave sintering method. The sintered samples were characterized using X-ray diffraction and scanning electron microscope. The grain sizes of the sintered samples are in the range of 60-80 nm. The ultrasonic velocities have been measured on MgCuZn ferrites using the pulse transmission method at 1 MHz. The ultrasonic velocity is found to decrease with an increase of temperature. A small anomaly is observed around the Curie temperature, 520 K. The anomaly observed in the thermal variation of longitudinal velocity and attenuation is explained with the help of magneto-crystalline anisotropy constant.     

Electromechanical properties of bismuth germanium oxide (Bi12GeO20)

The elastic and piezoelectric constants and their temperature coefficients of bismuth germanium oxide have been determined. All of the elastic and piezoelectric constants were obtained from dynamic measurements of piezoelectrically driven narrow bars and thin plates at the temperature 22 °C. The temperature coefficients were measured on the same resonators in the temperature range from 16 °C to 70 °C. The thermal expansion measured in the temperature range from 50 °C to 200 °C is also given.The author wishes to acknowledge the help rendered by Professor Ing. Dr.Jaroslav Stank in connection with the measurement of the thermal expansion coefficient and by R.Trepera in the course of the preparation of the measured resonators.     

Dielectric, thermal and optical study of an unusually shaped liquid crystal

Dielectric measurements have been carried out for the determination of real and imaginary parts of the permittivity of a newly synthesized, unusually shaped liquid crystal. The sample has been investigated in the frequency range from 100 Hz to 10 MHz within a temperature range 80-130 °C. The dielectric measurements in the smectic A phase indicate a Cole-Cole type of dispersion, and the activation energy was found to be 5.5 meV by using the Arrhenius plot of relaxation time. In addition to this, thermal and optical transmittance studies have also been conducted in the above mentioned temperature range, and the temperature dependence of these parameters has been discussed in detail. The phase transition temperature obtained from a differential scanning calorimetry (DSC) study matches within 2 °C that was obtained from an optical transmittance study. The dielectric and optical behavior of the unusually shaped liquid crystal has been explained on the basis of a proposed theoretical model in which a sample possesses two different conformers having induced polarizations in opposite directions.     

Structural, optical and dielectric studies of glycinium trifluoroacetate single crystal

An organic material glycinium trifluoroacetate (GTFA) has been re-synthesized and large single crystals have been grown by solution technique. Complete structure of GTFA has been redetermined from single crystal XRD data. FTIR confirmed the presence of various functional groups. Melting point (152.44 °C), thermal stability and specific heat were studied from TG/ DTA and DSC. In UV absorption spectra, a lower cutoff value as 220 nm and a wide band gap as 4.86 eV for GTFA were observed. The dielectric studies, dielectric constant and loss were measured at different temperatures (30-90 °C) in the frequency range 100 Hz-2 MHz.     

Experimental temperature measurements by echo-contrast agents

The article considers results of experimental studies of the spectra of ultrasound echo-signals scattered by echo-contrast agents (ECA) at changing temperature. Two types of ECA have been used: Levovist being the suspension of free air bubbles and Definity whose gas bubbles are in an albumin shell. As the temperature increases the maxima of the frequency spectra of backscattering signals shift to low frequencies and the value of this shift serves to determine the true temperature. Experimental data on Levovist are well accorded with the calculations for the temperature range from 34 to 44°C and the frequency shifts were about 17 kHz/°C in the range of frequencies of 3.5—5 MHz. The Definity measured frequency shift versus temperature was 5 kHz/°C. The measured values of frequency shifts serve to the realization of the accuracy of temperature measurements of (0.1–0.2)°C. The obtained results prove the prospectiveness of special temperature ECA in the shells for the temperature mapping of internal organs by means of standard platforms of ultrasound diagnostics.     

Ferroelectric relaxor behaviour in Pb(Fe0.5Ta0.5)O3

The relaxor ferroelectric lead iron tantalate, Pb(Fe_0.5Ta_0.5)O₃ (PFT) is synthesized by Coulombite precursor method. The X-ray diffraction pattern of the sample at room temperature shows a cubic phase. The field dependence of dielectric response is measured in a frequency range 0.1 kHz — 1 MHz and in a temperature range from 173–373 K. The temperature dependence of permittivity (ɛ′) shows broad maxima at various frequencies. The frequency dependence of the permittivity maximum temperature (T _m ) has been modelled using Vogel-Fulcher relation.      

Structure and dielectric studies of nano-composite Fe2O3: BaTiO3 prepared by sol-gel method

Nano-structure pure barium titanate (BaTiO₃) and that was doped with iron oxide (Fe₂O₃), have been prepared by sol-gel method, using barium acetate (Ba(Ac)₂) and titanium butoxide (Ti(C₄H₉O)₄), as precursors. The as-grown prepared samples by sol-gel technique were found to be amorphous, which crystallized to the tetragonal phase after synthesized at 750 °C in air for 1 h as detected from the XRD patterns. The XRD data were confirmed by transmission electron microscope (TEM). The dielectric properties namely; dielectric constant (ε′) and loss tangent (tan δ) in the frequency range between 42 Hz and 1 MHz, at range of temperature 25-250 °C were investigated. The temperature dependence of ε′ and tan δ for the undoped and doped materials, at 1 kHz, was also investigated. As a result, tan δ increased rapidly with decreasing temperature below 125 °C (Curie temperature) while above this temperature, tan δ shows temperature independent. As a result, below and above Curie temperature, ferroelectric phase and paraelectric phase of BaTiO₃ can be obtained, respectively.     

Influence of substrate temperature on the optical and piezoelectric properties of ZnO thin films deposited by rf magnetron sputtering

In this study, ZnO thin films were fabricated using the rf magnetron sputtering method and their piezoelectrical and optical characteristics were investigated for various substrate temperatures. The ZnO thin film has the largest crystallization orientation for the (0 0 2) peak and the smallest FWHM value of 0.56° at a substrate temperature of 200 °C. The surface morphology shows a relatively dense surface structure at 200 °C compared to the other substrate temperatures. The surface roughness shows the smallest of 1.6 nm at a substrate temperature of 200 °C. The piezoelectric constant of the ZnO thin film measured using the pneumatic loading method (PLM) has a maximum value of 11.9 pC/N at a substrate temperature of 200 °C. The transmittance of the ZnO thin film measured using spectrophotometry with various substrate temperatures ranged from 75 to 93% in the visible light region. By fitting the refractive index from the transmittance to the Sellmeir dispersion relation, we can predict the refractive index of the ZnO thin film according to the wavelength. In the visible light range, the refraction index of the ZnO thin film deposited at a substrate temperature of 200 °C is the range of 1.88-2.08.     

Crystallization of (Bi,Nd)4Ti3O12 films in N2 environment by chemical solution deposition

(Bi,Nd)₄Ti₃O₁₂ (BNT) ferroelectric films were deposited on Pt/Ti/SiO₂/Si substrates by chemical solution deposition and crystallized in an N₂ environment after pre-annealing in air at 500 °C. The effect of crystalline temperature on the structural and electrical properties of the BNT films was studied. The BNT films annealed in N₂ in the temperature range of 630 °C to 670 °C were crystallized well and the average grain size increased with increasing crystalline temperature, while the remanent polarization and dielectric constant of the films are not a monotonic function of the crystalline temperature. The BNT films crystallized at 650 °C have the largest remanent polarization value of 2P_r=63.6 μC/cm², a dielectric constant of 344 at 10 kHz, and a fatigue-free characteristic. A positive correlation between the remanent polarization and the dielectric constant of the BNT films has been observed. PACS 81.20.Fw; 81.40.Ef; 77.84.-s     

Preparation, structural analysis and dielectric properties of Bi x La1−x FeO3 perovskite

Rare earth element substituted bismuth ferrites (BiFeO₃) are of enormous importance as magnetoelectric materials. The polycrystalline samples of Bi _x La_1−x FeO₃ (x=0, 0.2, 0.4, 0.6, 0.8) were prepared by solid-state reaction using standard ceramic method. The single-phase formation of these compounds was confirmed by X-ray diffraction (XRD) studies. The samples with x=0, 0.2, 0.4, 0.6 are found to be orthorhombic while the sample with x=0.8 is triclinic. The dielectric constant (ε′) and dissipation factor (tan δ) were measured in the frequency range 100 Hz to 1 MHz at room temperature and as a function of temperature at certain fixed frequencies (1 kHz, 10 kHz, 100 kHz, 1 MHz). All the samples showed dielectric dispersion. The dielectric constant with temperature shows a broad peak; the peak temperature shifts with frequency which reflects the relaxor-type behavior. The peak above 600 K in the measured temperature range corresponds to antiferromagnetic ordering temperature (Néel temperature). The broadness of the peak changes with composition. The ac conductivity as well as ε′ are found to be maximum for the sample x=0.2 at room temperature.     

Modification of dielectric relaxations in sodium bismuth titanate with samarium doping

Na_0.5Bi_(0.5−x) Sm_xTiO₃ (NBST) ceramics with x=0.05, 0.1, and 0.15 are prepared through chemical route. The X-ray diffraction studies confirmed the formation of single phase. Dielectric measurements in the temperature region ranging from room temperature (∼30 °C) to 600 °C at different frequencies (10 kHz-1 MHz) showed anomalies at 130, 306, and 474 °C (at 10 kHz frequency) for x=0.05 sample. Other samples showed only two peaks. To establish the electrical nature of these relaxations, impedance measurements are done at different temperatures and frequencies. The relaxation time, obtained from both impedance and modulus data, is found to decrease with increase in temperature. The relaxations observed are of non-Debye type. Increase in samarium content increases the activation energy for relaxation.     

Effect of sintering temperature on structure and nonlinear dielectric properties of Ba0.6Sr0.4TiO3 ceramics prepared by the citrate method

Ba_0.6Sr_0.4TiO₃ ceramics were prepared by a citrate precursor method. The structure and nonlinear dielectric properties of the resulting ceramics were investigated within the sintering temperature range 1200-1300 °C. Adopting fine Ba_0.6Sr_0.4TiO₃ powder derived from the citrate method was confirmed to be effective in reducing the sintering temperatures required for densification. The ceramic specimens sintered at 1230-1280 °C presented relative densities of around 95%. A significant influence of sintering temperature on the microstructure and nonlinear dielectric properties was detected. The discrepancy in nonlinear dielectric behavior among the specimens sintered at different temperatures was qualitatively interpreted in terms of the dielectric response of polar micro-regions under bias electric field. The specimens sintered at 1230 and 1250 °C attained superior nonlinear dielectric properties, showing relatively low dielectric losses (tan δ) of 0.24% and 0.22% at 10 kHz together with comparatively large figure of merits (FOM) of 121 and 142 at 10 kHz and 20 kV/cm, respectively.     

Dielectric properties and magnetoelectric effect of (x)NiFe2O4+(1−x)Ba0.8Sr0.2TiO3 composites

Magnetoelectric composites of NiFe₂O₄ and Ba_0.8Sr_0.2TiO₃ were prepared using conventional double-sintering ceramic method. The phase formation of magnetoelectric composites was confirmed by XRD technique. Variation of dielectric constant and loss tangent at room temperature with frequency in the range 100 Hz-1 MHz has been studied. Also the variation of dielectric constant and loss tangent with temperature and composition at fixed frequencies of 1 kHz, 10 kHz, 100 kHz and 1 MHz is reported. The static value of the magnetoelectric conversion factor was measured as a function of intensity of the magnetic field. The ME voltage coefficient of about 430 μV/cm Oe was observed for 15% NiFe₂O₄+85% Ba_0.8Sr_0.2TiO₃ composite. All the samples show linear variation of magnetoelectric conversion in the presence of static magnetic field.     

Application of SH surface acoustic waves for measuring the viscosity of liquids in function of pressure and temperature

Viscosity measurements were carried out on triolein at pressures from atmospheric up to 650 MPa and in the temperature range from 10 °C to 40 °C using ultrasonic measuring setup. Bleustein–Gulyaev SH surface acoustic waves waveguides were used as viscosity sensors. Additionally, pressure changes occurring during phase transition have been measured over the same temperature range. Application of ultrasonic SH surface acoustic waves in the liquid viscosity measurements at high pressure has many advantages. It enables viscosity measurement during phase transitions and in the high-pressure range where the classical viscosity measurement methods cannot operate. Measurements of phase transition kinetics and viscosity of liquids at high pressures and various temperatures (isotherms) is a novelty. The knowledge of changes in viscosity in function of pressure and temperature can help to obtain a deeper insight into thermodynamic properties of liquids.     

Influence of temperature variations on the entropy and correlation of the Grey-Level Co-occurrence Matrix from B-Mode images

In this work, the feasibility of texture parameters extracted from B-Mode images were explored in quantifying medium temperature variation. The goal is to understand how parameters obtained from the gray-level content can be used to improve the actual state-of-the-art methods for non-invasive temperature estimation (NITE). B-Mode images were collected from a tissue mimic phantom heated in a water bath. The phantom is a mixture of water, glycerin, agar-agar and graphite powder. This mixture aims to have similar acoustical properties to in vivo muscle. Images from the phantom were collected using an ultrasound system that has a mechanical sector transducer working at 3.5 MHz. Three temperature curves were collected, and variations between 27 and 44 °C during 60 min were allowed. Two parameters (correlation and entropy) were determined from Grey-Level Co-occurrence Matrix (GLCM) extracted from image, and then assessed for non-invasive temperature estimation. Entropy values were capable of identifying variations of 2.0 °C. Besides, it was possible to quantify variations from normal human body temperature (37 °C) to critical values, as 41 °C. In contrast, despite correlation parameter values (obtained from GLCM) presented a correlation coefficient of 0.84 with temperature variation, the high dispersion of values limited the temperature assessment.