Effect of atmospheric pressure dielectric barrier discharge air plasma on electrode surface

In order to study the influence of plasma on electrode, atmospheric pressure dielectric barrier discharge (DBD) air plasma is employed here to treat copper electrode surface. Plasma is generated between the parallel plate electrodes by means of high voltage produced by a high-frequency power supply with transformer. Electrode surface alterations induced by air plasma are investigated by using field emission scanning electron microscope (FE-SEM), X-ray energy dispersion spectroscopy (EDS) and contact angle measurement. The results show that DBD air plasma removes the organic contaminant on surface and causes electrode surface roughness, oxidization and nitridation. In addition, surface wettability is also improved, as concluded from contact angle measurements.     

同轴介质阻挡放电发生器介质层等效电容和负载特性研究

大气压介质阻挡放电(DBD)可以在常压下产生非平衡等离子体,已经成为热点研究领域.通过脉冲或交变电源激发放电,研究电源输出特性、电源与放电发生器负载间的匹配和外界条件对放电的影响对于理解放电现象和提高放电效率具有重要意义.本文采用Lissajous图形法,分别研究了驱动电压、气流速率等因素影响同轴DBD发生器介质层等效电容及负载幅频特性的规律.结果表明,气流速率和驱动电压等外界条件影响DBD发生器的负载特性:介质层等效电容随气流速率增大而减小,随驱动电压增大而增大;幅频特性曲线均表现出RLC回路谐振现象,谐振频率随气流速率增大而增大,随驱动电压增大而减小.通过对比发现,介质层等效电容随频率的变化曲线与幅频特性曲线具有一致的特征,介质层等效电容是影响电路谐振频率动态变化的主要因素.提出了一种有关介质层等效电容的形成机制.     

常压窄间隙介质阻挡放电等离子体辐射特性

利用带有透明电极与可测向观察的一个介质阻挡放电(DBD)实验装置对它的常压窄间隙等离子体辐射特性进行了实验研究。结果表明：这一DBD装置的辐射特性会受激励电压、激励频率、DBD结构等多种因素影响。在频率为10～20kHz高压电源激励下，采用窄间隙、薄电介质层结构DBD可以大幅度提高放电空间的电场强度，增加放电功率密度，提高了放电装置性能。     

基于Marx的任意极性方波脉冲电源设计北大核心CSCD

设计了一种基于Marx电路的方波脉冲电源,该电源采用磁环隔离驱动方案与全桥Marx电路相结合,实现了正极性、负极性和双极性高压方波脉冲的输出,解决了常规脉冲电源只能输出特定极性脉冲的限制。对电路的运行模式经行了理论分析,并搭建了16级实验样机。实验结果表明:在空载条件下,实现了频率1 kHz,幅值10 kV的正极性、负极性及双极性高压方波脉冲输出。其最小脉宽1μs,极性可调。该脉冲电源结构紧凑,可以实现输出电压、脉宽、脉冲极性可调。最后使用该方波脉冲电源驱动平行板介质阻挡放电反应器。结果表明:该方波脉冲电源可以作为介质阻挡放电驱动源。     

圆筒状DBD放电特性模拟研究

用XOOPIC软件对同轴圆筒状反应装置DBD放电特性进行了二维模拟研究。在频率为20kHz、正弦电压幅值为5kV的大气压氩气放电中,再现了微放电通道形成和发展过程,其微放电的寿命约为4ns。获得了电子、离子、介质表面电荷密度和电场强度随空间和时间的分布,发现在高压线圈的位置附近电子、离子和介质表面电荷密度存在极值。与典型平板介质阻挡放电相比,微放电中的电子密度、场强增加2~3个数量级。     

交流和纳秒脉冲Ar/H2O介质阻挡放电聚丙烯材料表面亲水改性对比研究

为了提高等离子体对聚合物材料表面处理的应用效果,优化亲水处理的条件,研究了交流和纳秒脉冲氩气介质阻挡放电（DBD）中添加适量H₂O,对聚丙烯（PP）亲水改性的处理效果。利用电学和光学诊断方法,系统地对比了交流DBD和纳秒脉冲DBD的放电特性,结果表明,纳秒电源驱动DBD具有更高的放电瞬时功率,更好的放电均匀性和更高的能量效率。通过测量不同水蒸气含量下DBD的OH发射光谱强度,确定了PP材料亲水性处理中H₂O添加的最优含量。利用交流和纳秒脉冲电源驱动DBD分别对PP材料进行亲水改性的处理,测量了不同条件下改性处理后的表面水接触角,并利用原子力显微镜（AFM）和傅里叶红外光谱（FTIR）分别对处理前后PP材料的表面物理形貌和表面化学成分进行分析。结果发现,经DBD处理后PP材料的水接触角明显降低,表面粗糙度明显增大,表面的亲水性含氧基团,羟基（?OH）和羰基（C=O）的数量大幅增加。相比交流电源,纳秒脉冲DBD处理的改性效果更好,其处理后的材料表面水接触角,比交流DBD处理的低5°左右,表面粗糙度也有所提升。而水蒸气的加入可使PP材料的表面水接触角进一步减小4°左右,表面粗糙度明显提升。研究结果为优化DBD聚合物材料表面改性实验条件及处理的效果提供了重要的参考依据。     

Amine-containing film deposited in pulsed dielectric barrier discharge at a high pressure and its cell adsorption behaviours

With monomer allylamine, amine-containing functional films were prepared in alternative current pulsed dielectric barrier discharge (DBD) at a high pressure. This paper analyses in detail the film properties and structures, such as hydrophilicity, compounds and microstructures as well as amine density by the water contact angle, Fourier transform infrared spectroscopy, atomic force microscopy, and ultraviolet--visible measurement. The influence of discharge parameters, in particular applied power, on amine density was investigated. As an application the cell adsorption behaviours on plasma polymerization films was performed in-vitro. The results show that at a high pressure pulsed DBD plasma can polymerize films with sufficient amine group on surface, through which the very efficient cell adsorption behaviours was demonstrated, and the high rate of cell proliferation was visualized.     

Electrostatic precipitation in wire-to-cylinder configuration: Effect of the high-voltage power supply waveform

The purpose of this paper is to study the effect of the high-voltage power supply waveform and the presence of a dielectric barrier on the collection of submicron particles in a wire-to-cylinder electrostatic precipitator. The experiments are carried out on two reactors (with or without dielectric barrier on the surface of the cylindrical collector electrode) with the same active section and volume. The results show that the highest collection efficiency is obtained with the negative dc corona. At equivalent electric power consumption, the Dielectric Barrier Discharge (DBD) is as effective as the positive dc corona and the ac corona. The efficiency can reach 99% with both studied reactors, if the necessary power is provided.     

Dielectric barrier discharge in needle-to-plane configuration: Model of surface charge relaxation

Relaxation process of surface charge owing to dielectric barrier discharge (DBD) in “needle – air gap – polyethylene terephthalate film – plane” configuration is considered. Experimental data of the surface charge relaxation (SCR) are obtained by means of the rotating capacitive probe. Taking into account Gaussian radial distribution of accumulated charge density, effective surface and volume electrical conductivities of a barrier dielectric, phenomenological model of SCR for any dielectric thickness is proposed and exact solutions are obtained. The adequacy of the model is confirmed by the numerical computation. There is a good agreement between the experimental results and the model calculations.     

μs振荡脉冲电源激励下同轴电极介质阻挡放电特性

 采用μs振荡脉冲电源激励同轴电极结构产生空气中介质阻挡放电(DBD),通过电压-电流波形的测量及发光图像拍摄研究了放电特性,计算得到了放电功率及传输电荷量等重要放电参量,研究了电压幅值、气隙距离对放电特性及放电参量的影响,在分析放电机理的基础上对实验结果进行了解释。结果表明:μs振荡脉冲电源激励下,DBD平均放电功率可达上百W,传输电荷量可达几千nC;增大电压幅值和减小放电气隙距离能获得更剧烈的放电,平均放电功率和传输电荷量均增加。     

纳秒脉冲表面介质阻挡放电特性实验研究

在常规大气环境条件下,基于单极性纳秒脉冲电源对表面介质阻挡放电特性进行了实验研究。结果表明:纳秒脉冲表面介质阻挡放电的本质是丝状放电,放电集中在电压脉冲的上升沿;激励电压和脉冲重复频率越大,放电越强烈,越接近均匀放电,但电压的作用更侧重于均匀性,而频率的作用则侧重于放电的强度;电极间隙的优化可以使表面介质阻挡放电特性最好;玻璃作为阻挡介质时容易发生沿面闪络。     

米量级常压等离子体改性装置及其在纺织材料改性中的应用

介绍了自制的1m尺度介质阻挡电连续表面改性处理装置。论述了米量级常压介质阻挡放电的物理特性,探讨了介质阻挡放电的电压、功率、频率等电学参量之间的关系。给出了使用此装置连续对涤纶(PET)织物、熔喷PBT非织造布和羊毛织物三种纺织材料进行改性实验结果,得到了相应的扫描电子显微镜(SEM)图片,分析了材料表面改性的原因。     

Geometrical optimization of a surface DBD powered by a nanosecond pulsed high voltage

In this study, surface Dielectric Barrier Discharge (DBD) actuators powered by nanosecond pulsed high voltage are investigated. The goal is to experimentally characterize the surface DBD actuators in terms of electrical and geometrical parameters.The actuators are made of two conducting electrodes separated by a thin dielectric (Kapton films) and arranged asymmetrically. The active electrode is connected to a pulsed high voltage power supply (voltage up to ±10 kV, rise and fall times of 50 ns and pulse width of 250 ns) and the second electrode is grounded.The experimental results show that the energy per pulse (normalized by the length of the active electrode) is smaller when one increases the inter-electrode spacing between 1 and 3 mm, the thickness of the dielectric barrier between 120 and 360 μm or the length of the electrodes between 10 and 50 cm, for both applied voltage polarities.Optical characterization of the plasma layer for different electrode gaps has been investigated by using an ICCD camera. Results indicate that the plasma produced by positive and negative rising voltage propagates in a streamer-like regime with numerous and well-distributed channels, for any electrode gap distance. However, the positive and negative falling voltage produces similar discharges only for large electrode gaps. In this case, the plasma layer starts from a corona spot in contact with the active electrode and expands in the direction of the grounded electrode in a plume shape.     

共面介质阻挡放电特性研究

对共面介质阻挡放电(DBD)的放电过程进行了实验和理论研究. 在实验中设计了分段电极方法来获取放电过程中不同位置上的局域电流和光辐射特性，得到了阴极上等离子体的扩展速度，并与二维流体数值模拟结果进行了比较. 结果表明，在共面DBD的暂态放电过程中，电极上空等离子体区域始终存在有不均匀电场，导致了不同位置上放电电流和光辐射分布的不一致. 同时研究还表明，在DBD放电过程中应当考虑表面光致二次电子发射. 关键词： 介质阻挡放电 分段电极 放电特性     

Surface dielectric barrier discharge: Effect of encapsulation of the grounded electrode on the electromechanical characteristics of the plasma actuator

Active flow control is a rapidly developing topic because the associated industrial applications are of immense importance, particularly for aeronautics. Among all the flow control actuators, plasma-based devices are very promising. In most cases, the plasma actuator is based on a surface dielectric barrier discharge (DBD) established between two electrodes flush mounted on both sides of a dielectric layer. In this paper, the effects of the encapsulation of the grounded electrode on the electric wind produced by a surface DBD are investigated by Pitot velocity measurements. Moreover, the current versus time is statistically analysed in order to count the number of streamers, their duration and the electrical charge they transfer. Unfortunately it was not possible to detect and separate the glow-type synchronous current because its amplitude is of the same order as noise. On one hand, the encapsulation of the grounded electrode results in an increase of the electromechanical efficiency of the surface DBD plasma actuator because the electrical power consumption is divided by two. On the other hand, statistical analysis of the discharge current versus time has shown that the encapsulation results in a decrease of the streamer number and an increase of the charge transferred by each current streamer because the duration of streamers is longer.     

The effect of air plasma on barrier dielectric surface in dielectric barrier discharge

Barrier dielectric is an important part of atmospheric pressure dielectric barrier discharge (AP-DBD), which partly affects discharge characteristics. Conversely, discharge plasma also has influence on dielectric surface properties. To investigate this influence, some experiments were carried out on a home-built AP-DBD system with glass plate as barrier dielectric. Surface wettability was evaluated by water contact angles on a drop shape analysis system. The morphologies and chemical compositions of the glass sample surfaces were observed by field-emission scanning electron microscope (FESEM) and energy dispersive X-ray spectroscopy (EDS) attached to FESEM. The results show that water contact angles decrease as discharge energy increases, micro-discharge etching zones are formed into glass surface and different from the control glass in surface micro-structure and chemical compositions.     

介质阻挡放电中微放电周期特性的光学测量

采用特殊设计的双水电极介质阻挡放电装置,利用光学方法原位、无干扰地测量了大气压空气介质阻挡放电中微放电的单脉冲特性和周期特性,实验上首次发现在介质阻挡放电斑图模式中,微放电在驱动电压的正负半周的放电时刻并不是固定的,相邻两次放电的时间间隔是长短交替的。根据壁电荷对微放电通道相邻两次放电的不同作用,分析了相邻两次放电时刻的联系,很好地解释了相应的实验现象。     

大气压氖气介质阻挡放电脉冲等离子射流特性

采用自行研制的低造价、小体积、可产生幅值0~35 kV、重复频率1 kHz的高压s脉冲电源,设计了一套以大气压氖气为工作气体的介质阻挡放电（DBD）等离子体射流源,通过测量并计算放电过程中的电压-电流波形、拍摄放电图像、光谱分析等手段,对电压幅值、气体流速对氖气等离子体射流特性的影响进行了研究。结果表明:s脉冲电源激励下大气压氖气DBD能产生锥状的等离子射流且其等离子强度适中;s脉冲电源电压幅值的快速上升,可在放电空间瞬间施加高的过电压,能有效促进放电功率、电子密度、电子激发温度和射流长度的增加;工作气体流速的增加使得放电功率、电子激发温度和电子密度减小,而射流长度变化很小;一定条件下,能形成长距离的射流。     

常压介质阻挡放电等离子体发射光谱的检测分析

以常压介质阻挡放电等离子体作为研究对象,在常温常压条件下使用介质阻挡放电光谱诊断装置,得到N2第二正系跃迁和Ar原子发射谱线。通过对放电光谱的检测分析,可以察知常压介质阻挡放电等离子体的特性,并可运用同一元素谱线的相对强度来诊断电子激发温度等物理参量,以达到对材料表面改性过程的实时监控,工作的结果对常压介质阻挡放电及其在材料改性的应用中具有重要的意义。     

Effects of dielectric barrier discharge in air on morphological and electrical properties of graphene nanoplatelets and multi-walled carbon nanotubes

Multi-walled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) have been functionalized by dielectric barrier discharge (DBD) in air. The extent of functionalization of MWCNTs and GNPs reaches a maximum at the delivered discharge energy of 720 and 240 J mg⁻¹, respectively. Further exposure to plasma leads to reduction of functional groups from the surface of the treated nanomaterials. It has also been demonstrated that DBD plasma does not produce dramatic structural changes in MWCNTs, while flakes of the treated GNPs become thinner and smaller in the lateral size. Conductive thin films, obtained by drop casting a solution of the treated nanomaterials in N-methyl-1-pyrrolidone on poly(methyl methacrylate) substrate, show significantly lower sheet resistance.