In situ observation of NaBi(WO4)2 dendrite growth and the study on microstructure of solidification

The dendrite growth process of transparent NaBi(WO₄)₂ with small prandtl and high melting point was studied by using the in-situ observation system. According to the dynamic images and detailed information, there are two kinds of restriction effect on the dendrite growth, the competition between arms and branches and the convection in the melt. The dendrite growth rate was time dependent, and the rate of arm growth reached the maximum 5.8 mm/s in the diffusive-advective region and rapidly decreased in the diffusive-convective region. The growth rate of branch had the same change trends as the arm’s. Based on the EPMA-EDS data of solidification structure of quenched NaBi(WO₄)₂ melt, it was found that there were component differences from stoichiometric concentration in the melt near the interface during the growth process. Supported by the National Natural Science Foundation of China (Grant No. 50331040) and the Innovation Funds from Shanghai Institute of Ceramics, Chinese Academy of Sciences (Grant No. SCX0623)     

对流作用下枝晶形貌演化的数值模拟和实验研究

合金凝固过程中存在于枝晶尖端液相区的强制对流和自然对流均能改变溶质扩散层厚度,从而会对枝晶形貌产生较大影响.在元胞自动机模型基础上,耦合液体流动方程、热传导方程和溶质对流扩散方程,建立了新的计算微观组织演化的数值模型,并利用该模型研究了强制对流和自然对流对枝晶生长的影响.三维数值模拟结果再现了强制对流作用下等轴枝晶的生长过程,揭示了强制对流对枝晶生长速率和尖端半径的影响特点.同时利用该模型模拟了NH₄Cl-H₂O溶液定向凝固过程中自然对流对柱状晶生长的影响,并采用相应的实验进行验证.模拟结果与实验结果符合良好,从而证明该模型是可靠的,可推广到实际合金系中. 关键词： 元胞自动机 对流 4Cl-H₂O溶液')" href="#">NH₄Cl-H₂O溶液 定向凝固     

Selection of stable growth conditions for the parabolic dendrite tip in crystallization of multicomponent melts

Free growth of a dendrite crystal in a stationary multicomponent melt is investigated. A mathematical model of the process is developed and its analytic solution is constructed. A stability criterion is obtained for a 2D parabolic dendrite and the refined relation is derived for the growth rate of the dendrite tip taking into account the anisotropy of surface tension at the solid phase-melt interface. It is shown that the accumulation of impurity in the front of a dendrite makes it tip thinner and reduces its velocity. The theory contains limiting transitions to the familiar dendrite growth criteria for one-component and binary systems.     

Heat transfer and diffusion-controlled kinetics of liquid–solid phase in titanium matrix composite during selective laser melting

This study describes a self-consistent theoretical model of simulating diffusion-controlled kinetics on the liquid–solid phase boundary during high-speed solidification in the melt pool after the selective laser melting (SLM) process for titanium matrix composite based on Ti–TiC system. The model includes the heat transfer equation to estimate the temperature distribution in the melt pool and during crystallization process for some deposited layers. The temperature field is used in a micro region next to solid–liquid boundary, where solute micro segregation and dendrite growth are calculated by special approach based on transient liquid phase bonding. The effect of the SLM process parameters (laser power, scanning velocity, layer thickness and substrate size) on the microstructure solidification is being discussed.     

PbMoO4晶体生长基元和生长习性的高温拉曼光谱研究

应用高温拉曼光谱研究了PbMoO₄熔体中的生长基元.通过对不同温度下PbMoO₄晶体拉曼光谱和熔点温度附近熔体高温拉曼光谱的研究,发现PbMoO₄熔体中存在Pb²⁺阳离子和［MoO₄］^2－阴离子生长基元.进一步讨论了PbMoO₄晶体生长基元和各个低指数晶面间的相互作用,解释了晶体的生长习性和枝晶生长的原因,并指出:PbMoO₄晶体生 关键词： 钼酸铅晶体 枝晶 籽晶取向 拉曼光谱     

宏微观耦合模拟熔池不同区域中枝晶竞争生长过程

针对熔化焊过程建立了宏微观耦合模型,模拟了熔池内不同区域凝固过程中随机取向枝晶的竞争生长过程. 通过宏观三维有限元模型计算熔池中瞬态的传热传质过程,利用双线性插值算法将凝固参数传递给微观组织模型. 采用元胞自动机法模拟随机取向的枝晶在熔池凝固条件下的竞争生长过程. 模拟结果表明,所建立的微观模型能够精确模拟任意生长取向的枝晶. 凝固条件中最大温度梯度方向对枝晶竞争过程有明显选择作用,生长方向与最大温度梯度方向相同或接近的枝晶在竞争中具有更大优势. 焊缝中的晶粒组织由枝晶簇发展形成,晶粒组织的形貌演变取决于相邻枝晶簇之间的竞争过程,具有择优取向的枝晶簇会逐渐排挤非择优取向的枝晶簇并最终将其阻挡在凝固组织内部,宏观晶粒的取向与其内部枝晶簇的生长方向并不一定相同. 熔池中心线附近区域在焊接过程中具有更小的温度梯度、更大的凝固速率以及更大的局部冷却速率,凝固后可以获得更加细小的焊缝枝晶组织. 枝晶间距的模拟结果与相应凝固条件下的试验数据符合较好. 关键词： 焊接熔池 枝晶形貌 竞争生长 元胞自动机     

The attenuation of oscillatory thermocapillary convection in the oxide melt by a transverse magnetic field

The effect of a transverse magnetic field on the oscillatory thermocapillary convection in the NaBi(WO4)2 melt was studied by using the in-situ observation system. The oscillation was attenuated when the 60 mT magnetic field was applied, as shown by the decrease in the amplitude and the frequency. Furthermore, the oscillation under smaller temperature difference was stabilized after the magnetic field was applied. The magnetic effect could be due to the Lorentz force generated by the interaction between motional ions and the vertical magnetic field. The ionic conductivities were measured to demonstrate the effect of the magnetic field. The solid ionic electrical conductivity increases with the temperature rise, and the melt ionic electrical conductivity was measured to be about 2.0×10-4 Ω-1·cm-1. Experimental results manifest that the effect of the magnetic field on anions and cations in the melt makes the flow change to the direction normal to the applied field, so the flow is more orderly and the oscillation is suppressed.     

Ag负载WO3/TiO2光催化剂的合成及其催化性能

以钛酸丁酯、无水乙醇、钨酸铵为原料,采用溶胶-凝胶法合成了WO3/TiO2复合光催化剂;采用光还原技术制备了Ag负载WO3/TiO2光催化剂,借助X射线粉末衍射(XRD)和UV-Vis光谱等技术对样品的组成和光吸收性能进行了表征,并以罗丹明B为模型污染物考察样品的光催化活性。XRD分析表明,所得粉体均为锐钛矿型纳米TiO2,且与WO3复合后,纳米TiO2特征衍射峰宽化,强度降低;UV-Vis光谱分析表明,载银使得催化剂在400—700nm的可见光区域对光响应,且在紫外光区吸收显著增强,对光具有更高的利用率;以罗丹明B为降解物的光催化实验表明,WO3复合对纳米TiO2光催化活性有显著的影响,而载Ag后其光催化活性进一步提高,将该光催化剂用于炼油厂废水的处理,效果较好。     

旋转磁场对凝固组织形成的影响

研究了旋转磁场作用下Pb-45%Sn亚共晶合金的凝固组织.实验发现,旋转磁场的频率恒定时,凝固组织的晶粒尺寸随着磁场强度的增强而线性减小,同时,初生相的生长形态从枝晶转变为椭球状.X射线测试结果表明,初生相Pb发生了点阵膨胀,并且晶格常数随着磁场强度的增强先变大后减小,磁场强度在此存在一个临界值.能谱分析显示,随着磁场强度的增强,初生相Pb内Sn的含量逐渐降低.根据电磁场理论和扩散定律,对上述现象进行了理论分析,揭示出旋转磁场引起了液相强烈流动,加快了溶质原子的扩散以及对熔体的加热效应,导致了形核率的提高和长大速度的降低. 关键词： 旋转磁场 液相流动 晶格常数 溶质分配     

Effect of gravity convection on interface morphology during solidification

An experimental apparatus consisting of a crystal growth room and a crystal growth observation system was developed for the study of the effect of the gravity convection perpendicular to the growth direction on the growth process by use of model alloy succinonitrile (SCN)-5wt%ethanol. It was found that the convection improves the stability of the interface and causes the downstream alternation of the cell growth direction because of the dual effect of the Stokes force and the gravity. The second dendrite arm facing the flow comes into being earlier than that at another side when the interface transforms cell to dendrite. Then the dendrite at the side facing the flow comes into being earlier. The second dendrite arm facing the flow grows faster and is more developed than that at another side. In addition, the primary dendrite arm spacing increases and the dendrite tip radius decreases under the gravity convection. Supported by the National Natural Science Foundation of China (Grant Nos. 50331040 and 60171043)     

溶胶-凝胶法制备电致变色薄膜及器件的研究

用离子交换法制备ＷＯ３电致变色薄膜,并制备结构为ＷＯ３／ＬｉＣＯ４＋ＰＣ／ＴｉＯ２的夹层式半固态电致变色器件。测试了薄膜及器件的循环伏安特性曲线,研究了薄膜及器件在不同的扫描电压及扫描速率下的电致变色性能,并获得了ＷＯ３薄膜在导锂离子情况下的着色效率。实验证明,溶胶－凝胶法完全能够成为一种有效的制备大面积电致变色灵巧窗的方法。     

BCC枝晶生长原子堆垛过程的晶体相场研究

通过在自由能泛函中引入各向异性参数得到了一个基于高斯内核的改进晶体相场模型, 并采用该模型研究了体心立方结构(BCC)枝晶生长的原子堆垛过程. 结果表明, 在BCC由正十二面体平衡形貌演化为枝晶组织过程中, 形核位置经历了由面心({110}面)到尖端(<100>取向)的转移, 进而发生界面失稳形成枝晶组织; 枝晶生长过程中, 新的固相原子首先在枝晶尖端附近形核, 并快速向尖端及根部生长, 枝晶尖端被新原子完全包覆后将再次诱发液相原子附着形核及生长; 随初始液相密度的增加, 固-液界面移动速率增加, 速率系数的各向异性也增强.     

二元合金多晶粒的枝晶生长的等温相场模型

基于Ginzburg-Landau理论和单晶粒的枝晶生长模型,发展了一个单相场控制的多个晶粒的枝晶生长模型. 采用相场和溶质场耦合的方法,以Al-2%Cu合金为例模拟了二元合金等温凝固过程中多个晶粒的生长过程. 结果表明,这个模型的计算结果展现了多个晶粒枝晶的竞争生长,能较真实的再现凝固过程中的枝晶的生长过程. 关键词： 相场法 多晶粒 等温凝固 二元合金     

Mode-locked laser operation of epitaxially grown Yb:Klu(WO4)2 composites

Mode locking based on an epitaxial composite of the monoclinic double tungstate crystal Yb:KLu(WO4)2 is realized. A 100 microm thin Yb:KLu(WO4)2 layer grown on a KLu(WO4)2 substrate is used as an active medium in a laser passively mode locked by a semiconductor saturable absorber. Pulse durations of 114 fs have been achieved for an average power of 31 mW at 1030 nm. Results in the femtosecond and picosecond regimes of the Yb:KLu(WO4)2/KLu(WO4)2 laser are presented. The great potential of Yb-doped tungstate composite structures as active elements for mode-locked laser systems is demonstrated.     

Nd3+:NaLa(WO4)2晶体的生长和光学性质

用双坩埚法从高温溶液里生长出线度达7 mm的Nd3 : NaLa(WO4)2晶体.扫描电子显微镜的观察结果表明,虽然在晶体冷却过程中经历了两个相变,但相变并未造成晶体开裂;样品的X射线衍射花样可以看出,所得晶体为纯低温四方相的Nd3 :NaLa(WO4)2．在室温下对晶体的光吸收和光发射作了测量,发现晶体在804 nm有个半高宽达到23 nm的宽吸收峰．讨算出晶体在804 nm处的吸收截面为7．24×10-20 cm2,在1057 nm处的发射截面为6．54×10-20 cm2．     

二元合金多晶粒的枝晶生长的等温相场模型

基于Ginzburg-Landau理论和单晶粒的枝晶生长模型，发展了一个单相场控制的多个晶粒的枝晶生长模型. 采用相场和溶质场耦合的方法，以Al-2%Cu合金为例模拟了二元合金等温凝固过程中多个晶粒的生长过程. 结果表明，这个模型的计算结果展现了多个晶粒枝晶的竞争生长，能较真实的再现凝固过程中的枝晶的生长过程.     

Nd∶KY(WO4)2和Nd∶KG(WO4)2晶体吸收光谱性能分析

通过研究分析钨酸盐晶体Nd∶KY(WO₄)₂和Nd∶KG(WO₄)₂在室温下的吸收光谱，发现这2种晶体具有作为激光晶体的优良特性。根据Judd-Ofelt理论和测试所得的吸收光谱及数据，用VC++编程计算出晶体的谱线强度、振子强度、吸收截面等，拟合得Nd³⁺离子的3个晶场调节参数Ω_λ(λ=2，4，6)的值，并从理论上计算了自发跃迁几率、能级寿命、荧光分支比和积分发射截面。从计算得出的荧光分支比β可以看出，Nd∶KY(WO₄)₂(β_1060nm=0.4380)和Nd∶KG(WO₄)₂(β_1060nm=0.4618)晶体荧光分支比都较大，计算了该晶体的X=Ω₄/Ω₆，并将其X值与其他晶体的X值加以比较，Nd∶KY(WO₄)₂和Nd∶KG(WO₄)₂均易于实现1.06μm激光输出，适合作为LD泵浦的钨酸盐晶体激光器。     

Efficient thin-disk Tm-laser operation based on Tm:KLu(WO4)2/KLu(WO4)2 epitaxies

A diode-pumped thin-disk laser based on Tm:KLu(WO4)2/KLu(WO4)2 epitaxies is realized. The emission is in the 1850-1945 nm spectral range for Tm-doping between 5 and 15 at. %. The maximum slope efficiency of 47% with respect to the absorbed power obtained with 5 at. % Tm:KLu(WO4)2/KLu(WO4)2 corresponds to a maximum output power of ~6 W in cw operation.     

Phase——field model of isothermal solidification withmultiple grains growth

This paper develops a new phase--field model for equiaxed dendrite growth of multiple grains in multicomponent alloys based on the Ginzberg--Landau theory and phase--field model of a single grain. Taking Al--Cu and Al--Cu--Mg alloys for example, it couples the concentration field and simulates the dendrite growth process of multiple grains during isothermal solidification. The result of the simulation shows dendrite competitive growth of multiple grains, and is reapplied to the process of dendrite growth in practical solidification.