低温下二硫化钼电子迁移率研究

二硫化钼(MoS₂)是已知的二维半导体材料中光电性能最优秀的材料之一. 单原子层厚的MoS₂是禁带宽度为1.8 eV 的二维直接带隙半导体材料, 可以用来发展新型的纳米电子器件和光电功能器件. 本论文利用玻尔兹曼平衡方程输运理论研究低温时MoS₂系统的电输运性质, 计算得到了MoS₂电子迁移率的解析表达式. 研究发现, 低温时MoS₂ 的迁移率与衬底材料的介电常数的平方成正比; 与系统的电子浓度对带电杂质的浓度的比率n_e/n_i 成线性关系. 因此, 选用介电常数高的衬底材料, 适当提高MoS₂系统的载流子浓度, 同时降低杂质的浓度, 可以有效提高MoS₂系统的迁移率. 研究结果为探索以MoS₂为基础的新型纳米光电器件的研究和实际应用提供了理论依据. 关键词： 二硫化钼 迁移率 电输运 平衡方程     

K,Na掺杂Cu-S纳米晶的水热合成及对结构、性能的影响

利用水热合成技术, 分别以CuCl₂·2H₂O, 硫粉为铜源和硫源, 以KOH或NaOH为矿化剂, 成功合成了Cu₂S纳米晶体和碱金属离子掺杂的KCu₇S₄纳米线和NaCu₅S₃ 微纳米球. 通过X射线衍射(XRD)、电子能谱(EDS)、扫描电镜(SEM)、透射电镜(TEM)和高分辨率透射电镜 (HRTEM) 对产物的结构和形貌进行了表征和分析. 结果显示: KOH含量低于1g或NaOH低于2g时, 产物为斜方辉铜矿Cu₂S; 高碱含量 (不低于3g) 时, K或Na离子成功掺入产物结构中, K掺杂产物为纯净的四方相KCu₇S₄, 单晶结构, 尺寸均匀, 长度可达几十微米的纳米线; Na掺杂未改变产物的形貌, 形成六方晶系结构的NaCu₅S₃. 产物的形成和生长与反应温度、反应时间和矿化剂密切相关. 并讨论了Cu₂S纳米晶及其掺杂纳米晶的形成机理及掺杂机理. 最后研究了碱金属离子掺杂对产物的光学性能的影响, 漫反射光谱显示Cu₂S, KCu₇S₄和NaCu₅S₃纳米晶的光学带隙分别为1.21eV, 0.49eV和0.42eV, K⁺和Na⁺的掺杂, 极大的改变了产物的光学特性. 关键词： 7S₄')" href="#">KCu₇S₄ 5S₃')" href="#">NaCu₅S₃ 水热法 掺杂     

Au的金属颗粒对二硫化钼发光增强

二硫化钼(MoS₂)是一种层状的二维过渡金属硫族化合物材料,从块体到单层,禁带由间接带隙变为直接带隙,由于通常机械剥落的单层MoS₂是n型掺杂的,使得其发光效率仍然很低. 在本文中,采用匀胶机旋涂的方法将共振吸收峰在514 nm附近的纳米金颗粒尽可能均匀的铺在单层、双层以及多层的MoS₂样品表面,发现单层和双层样品的光致发光谱(PL谱)分别增强了约30倍和2倍同时伴随着峰位的蓝移,而多层样品的发光强度也略有增强. 拉曼特性揭示了纳米金颗粒对单层和双层MoS₂样品产生了明显的p型掺杂,从而增强了发光;同时纳米金颗粒的表面等离子激元效应对激发光的天线作用也是增强MoS₂的光致发光的一个因素. 关键词： 二硫化钼 光致发光 p型掺杂 Au纳米颗粒     

花状硫化铜级次纳米结构的制备及可见光催化活性研究

本实验以氯化铜 (CuCl₂·2H₂O) 和二硫化碳(CS₂)为原料, 以乙二醇(C₂H₆O₂) 为溶剂, 通过溶剂热法成功制备了具有可见光活性的花状硫化铜(CuS) 级次纳米结构. 并利用X射线粉末衍射技术(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM) 等技术对其进行了表征, 利用紫外可见吸收光谱(Uv-vis)分析了其光学性能, 并以甲基橙为目标降解物对其可见光催化活性进行了研究. 结果表明: 花状CuS级次纳米结构具有很高的可见光催化活性, 与体相CuS粉末相比有很大的提高, 在自然光照射下对甲基橙的降解率可以达到100%. 同时本文对花状级次纳米结构的形成机理进行了分析. 关键词： 硫化铜 溶剂热 级次纳米结构 光催化     

二硫化钼量子点的一步水热法制备与光学性能研究

二硫化钼量子点(MoS₂ QDs)因具有尺寸可控、量子限域效应强等优异的物化特性，故在传感、荧光检测和光催化等领域中具有潜在的应用价值。以钼酸铵为钼源，以谷胱甘肽为硫源，采用一步水热法合成水溶性好、尺寸均一的MoS₂QDs(MoS₂ QDs-1)。为探究不同硫源对MoS₂ QDs尺寸和光学性能的影响，又以钼酸铵和L-半胱氨酸分别为钼源和硫源，通过相同方法制备MoS₂ QDs(MoS₂ QDs-2)。研究了MoS₂ QDs-1和MoS₂ QDs-2样品的结构和光致发光性能。结果表明，与MoS₂ QDs-2样品相比，MoS₂ QDs-1样品的平均晶粒尺寸更小(3.88 nm)、平均晶粒高度更低(4.75 nm)、光学带隙更小(3.65 eV)和荧光量子产率更高(10.8%)。     

单层MoS2薄膜的NaCl双辅助生长方法

以单层二硫化钼(MoS₂)为代表的过渡金属硫族化合物半导体材料具有良好的光学、电学性质,近十年来引起了人们广泛的研究兴趣.合成高质量单层MoS₂薄膜是科学研究及工业应用的基础.最近科研人员提出了盐辅助化学气相沉积生长单层薄膜的方法,大大提高了单层MoS₂薄膜的生长速度及晶体质量.本文基于此方法,提出利用氯化钠(NaCl)的双辅助方法,成功制备了高质量的单层MoS₂薄膜.光致发光(PL)谱显示其发光强度比无NaCl辅助生长的样品有了明显的提高.本文提出的NaCl双辅助生长方法为二维材料的大规模生长提供了思路.     

钪钇石型β-Mn2V2O7的水热合成、结构表征与反铁磁性

用水热法新工艺在温度为200—220℃,pH值为6—9条件下合成出Mn₂V₂O₇粉晶.利用X射线衍射(XRD)、扫描电子显微镜(SEM)、能谱分析(EDS)、透射电子显微镜(TEM)、高分辨透射电镜(HRTEM)和电子衍射(SAED)分析了其物相、形貌及微结构,结果表明:合成产物均为单斜晶系的钪钇石型β-Mn₂V₂O₇;当合成温度为200℃时,pH值为6—7时合成产物的形貌为 关键词： 水热法 2V₂O₇')" href="#">β-Mn₂V₂O₇ 结构与形貌 反铁磁性     

d带中心理论探究MoS2电催化氢气析出反应机理的发展

二硫化钼(MoS₂)纳米片是一种典型的二维材料,因其独特可调的电子结构和优异的氢气析出反应(HER)电催化活性受到研究者的广泛关注.为了进一步提高其电催化性能,科学家深入研究反应的微观机理,以期阐明材料电子结构中影响电催化性能的关键因素,构建合理的电子描述符.本文综述了近年来d带中心理论探究MoS₂电催化HER机理的起源、发展和现状,以期为该类催化剂的进一步发展提供指导.     

合成温度和N2/O2流量比对碳纤维衬底上生长的SnO2纳米线形貌及场发射性能影响

采用化学气相沉积法系统研究了合成温度和N₂/O₂流量对生长在碳纤维衬底上的SnO₂纳米线形貌及场发射性能的影响规律. 利用扫描电镜(SEM)、透射电镜(TEM), X射线衍射(XRD)及能谱仪(EDS)对产物细致表征, 结果表明, SnO₂纳米线长径比随反应温度的升高而增大; 随N₂/O₂流量比值的增大先增大后变小, 场发射测试表明, 合成温度780 ℃, N₂/O₂流量比为300 : 3 时SnO₂纳米线阵列具有最佳的场发射性能, 开启电场为1.03 V/μm, 场强增加到1.68 V/μm时, 发射电流密度达0.66 mA/cm², 亮度约2300 cd/m².     

Cr和W掺杂的单层MoS2电子结构的第一性原理研究

采用密度泛函理论框架下的第一性原理平面波赝势方法, 研究了Cr和W掺杂对单层二硫化钼(MoS₂)晶体的电子结构性质的影响. 计算结果表明: 当掺杂浓度较高时, W对MoS₂的能带结构几乎没有影响, 而Cr的掺杂则影响很大, 表现为能带由直接带隙变为间接带隙, 且禁带宽度减小. 通过进一步分析, 得出应力的产生是导致Cr掺杂的MoS₂电子结构变化的最直接的原因.     

Facile synthesis and electrochemical properties of hierarchical MnO2 submicrospheres and LiMn2O4 microspheres

Hierarchical MnO₂ submicrospheres have been successfully synthesized by a wet chemical method. The as-prepared products were characterized by means of XRD, SEM, FTIR, TG, and TEM. With the as-prepared MnO₂ submicrospheres as precursors, LiMn₂O₄ microspheres were conveniently prepared by a simple solid-state reaction between MnO₂ and LiOH at a temperature as low as 600 °C. Electrochemical properties of the as-prepared MnO₂ submicrospheres and LiMn₂O₄ microspheres as cathode materials in lithium ion cells were investigated by galvanostatic charge/discharge tests.     

Characterization of K2CO3/Co–MoS2 catalyst by XRD,XPS, SEM,and EDS

MoS₂, Co–MoS₂ and K₂CO₃/Co–MoS₂ catalysts have been characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). XRD analysis indicates that Co–MoS₂ is a primary phase in K₂CO₃/Co–MoS₂ catalyst and the diffraction lines of Co–MoS₂ are not changed by the addition of K₂CO₃. Co₉S₈ phase is not present at Co/Mo mole ratio of 0.5 using a co-precipitation method for preparation of cobalt–molybdenum catalyst. The binding energies (BEs) of chemical species present on the surface of the catalysts are compared through the course of catalyst preparation. K₂CO₃/Co–MoS₂ catalyst has been investigated as a function of dispersion of K on the surface and exposure to a mixture of carbon monoxide and hydrogen (syngas) by scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The distribution of potassium on the surface of the K-promoted catalyst is not uniform.     

Mixed-solvothermal synthesis of CdS micro/nanostructures and their optical properties

Several novel cadmium sulfide (CdS) micro/nanostructures, including cauliflower-like microspheres, football-like microspheres, tower-like microrods, and dendrites were controllably prepared via an oxalic acid-assisted solvothermal route using ethylene glycol (EG) and H₂O as pure and mixed solvents with different S sources. The as-prepared products were characterized by X-ray powder diffraction (XRD), scanning electronic microscope (SEM) and UV-vis spectrophotometer (UV). It was found that CdS micro/nanostructures can be selectively obtained by varying the composition of solvent, concentration of oxalic acid, and sulfur sources. UV-vis absorption spectra reveal that their absorption properties are shape-dependent. The possible formation process of the CdS micro/nanostructures was briefly discussed. This route provides a facile way to tune the morphologies of CdS over a wide range.     

Facile synthesis and optical properties of Co3O4 nanostructures by the microwave route

Cobalt oxide (Co₃O₄) nanoplatelet shape like nanostructures have been successfully synthesized through a simple microwave route for the first time using cobalt acetate, NaOH and citric acid at 200 °C for 30 min. The structure and morphology of as-prepared Co₃O₄ nanoplatelets are characterized by means of powder X-ray diffraction (XRD), Fourier transform infrared spectrum (FTIR), and scanning electron microscope (SEM). XRD measurements indicate that the product has a perfect crystalline cubic phase of Co₃O₄ with a lattice constant a=8.082 Å. The SEM images show that the obtained Co₃O₄ nanopowder consists of nanoplatelets with diameter 125 nm and thickness 20 nm. Energy-dispersive X-ray spectroscopy (EDS) show that the composition of Co₃O₄ is stoichiometric. Room temperature photoluminescence measurement is exhibited by a strong UV emission and a suppressed green emission, confirming the good optical properties for the as-prepared Co₃O₄ nanoplatelets.     

Flower-like MoS<Subscript>2</Subscript> supported on three-dimensional graphene aerogels as high-performance anode materials for sodium-ion batteries

Flower-like MoS₂ supported on three-dimensional graphene aerogel (MoS₂/GA) composite has been prepared by a facile hydrothermal method followed by subsequent heat-treatment process. Each of MoS₂ microflowers is surrounded by the three-dimensional graphene nanosheets. The MoS₂/GA composite is applied as an anode material of sodium-ion batteries (SIBs) and it exhibits high initial discharge/charge capacities of 562.7 and 460 mAh g^?1 at a current density of 0.1 A g^?1 and good cycling performance (348.6 mAh g^?1 after 30 cycles at 0.1 A g^?1). The good Na⁺ storage properties of the MoS₂/GA composite could be attributed to the unique structure which flower-like MoS₂ are homogeneously and tightly decorated on the surface of three-dimensional graphene aerogel. Our results demonstrate that as-prepared MoS₂/GA composite has a great potential prospect as anodes for SIBs.     

Controlled preparation of unsupported binary and ternary sulfides with high surface area from tetraalkylammonium thiosalts

Unsupported MoS₂, WS₂ and Ni-MoS₂ sulfides have been successfully prepared by decomposition of tetraalkylammonium thiosalts, which were synthesized by using an aqueous solution of tetraalkylammonium halide and ammonium thiosalts at room temperature. The as-prepared samples were characterized by N₂ physorption, thermogravimetric analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results showed that structures and properties of unsupported binary and ternary sulfides depended on tetraalkylammonium thiosalts and decomposition conditions. The samples formed by decomposition of methyl and cetyltrimethyl substituted ammonium thiosalts exhibited high specific surface areas of above 100 m²/g, indicating the organic ligand in the precursor can tune the structure of the binary and ternary sulfides. MoS₂ and Ni-MoS₂ prepared from TMetATM and Ni/TMetATM had a relative narrow distribution in mesoporous range. TEM and XRD results revealed that the unsupported binary and ternary sulfides consisted of few-stacked layers and Ni was well-dispersed on MoS₂.     

Templated synthesis of plate-like MoS<Subscript>2</Subscript> nanosheets assisted with HNTs and their tribological performance in oil

Two-dimensional MoS₂ nanosheets were synthesized by using halloysite nanotubes (HNTs) as template under the hydrothermal synthesis. The structure and morphology of the as-synthesized MoS₂ nanosheets were determined by a series of characterizations. The results showed that the as-synthesized MoS₂ nanosheets were of the plate-like structure with about five layers, and the basal spacing was about 0.63 nm. It was demonstrated that HNTs played a crucial template role in the formation of the plate-like MoS₂ nanosheets. The formation mechanism was proposed. Furthermore, the tribological performance of the as-prepared MoS₂ nanosheets in oil was intensively examined on the ball-on-ball wear tester. The testing results verified that the as-prepared MoS₂ nanosheets as additive could significantly improve the friction performance of oil, which exhibited the good antifriction, antiwear, and load-carrying properties.     

Self-assembly of CuS nanoflakes into flower-like microspheres: Synthesis and characterization

Using Cu(S₂CNEt₂)₂ as a single-source precursor and ethylamine solution (65-70%) as the reaction medium, large-scale flower-like CuS microspheres have been synthesized via a solvothermal treatment in the presence of a surfactant. The products were characterized by XRD, SEM, TEM, HRTEM, and UV-vis spectrum. The assembled microspheres, with a diameter of about 2-3 μm, were composed of single-crystalline hexagonal CuS nanoflakes with a thickness of several tens of nanometers. It was revealed that the solvent medium, the surfactant, and the reaction time have great influence on the morphology and size of the resulting CuS products.     

Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Synthesis of high-edge exposure MoS2 nano flakes

Highly oriented edge exposure MoS₂ nano flakes were successfully synthesized via reaction between MoO₃ powder and S vapor at 700 °C for 2 h. The received MoS₂ flakes were characterized with SEM, TEM/HR-TEM, Raman spectroscopy, and XRD. TEM result shows that MoS₂ flakes are ~100 nm in diameter and compose of <10 layers (<5 nm). XRD and HR-TEM also prove that prepared MoS₂ flakes are highly crystallized with typical honeycomb structure.