Investigation on a novel ZnO/TiO2–B photocatalyst with enhanced visible photocatalytic activity

A new type of composite photocatalysts (ZnO/TiO₂–B) with Zinc oxide nanoparticles dispersed on boron doped titanium dioxide was prepared via a sol–gel method. The as-prepared powders were characterized by HRTEM, XRD, XPS, UV–vis DRS, and PL techniques. The results reveal that B³⁺ ions are doped into the TiO₂ lattice in interstitial mode, while ZnO nanoparticles are dispersed on the surface of TiO₂. The absorption of photocatalysts was extended into visible light region and the photogenerated electrons and holes were separated efficiently. Hence, ZnO/TiO₂–B composite photocatalyst exhibits much better photocatalytic activity than those of pure TiO₂ and TiO₂–B on photodegradation of 4-chlorophenol under visible light irradiation.     

Preparation, characterization and photocatalytic activity of polycrystalline Bi2O3/SrTiO3 composite powders

Bi₂O₃/SrTiO₃ composite powders have been prepared and their photocatalytic activities were investigated by photooxidation of methanol. These powders were characterized by UV-Visible diffuse reflectance spectra, SEM and X-ray diffraction (XRD). The results revealed that all the Bi₂O₃/SrTiO₃ composite powders exhibited higher photocatalytic activity than pure SrTiO₃, Bi₂O₃ and TiO₂ (P25) under visible light irradiation (λ>440 nm). The effects of the Bi₂O₃ contents on the photocatalytic activities of the composite powders were examined, the photocatalytic activities increased with the content of Bi₂O₃ increasing to a maximum of 83% and then decreased under visible light irradiation. The effects of the calcination temperatures on the photocatalytic activities of the composite powders were also investigated.     

Preparation of Fe2O3/SrTiO3 composite powders and their photocatalytic properties

Fe₂O₃/SrTiO₃ composite powders have been prepared and their photocatalytic activities were investigated by photooxidizing methanol. These powders were characterized by ultraviolet (UV)-visible diffuse reflectance spectra, scanning electron microscope (SEM) and X-ray diffraction (XRD). The results showed that the Fe₂O₃/SrTiO₃ composite powders with optimum proportion exhibited higher photocatalytic activity than pure SrTiO₃, Fe₂O₃ and TiO₂ (P25) under visible light (λ>440 nm) irradiation. The SEM image of the composite powders showed that SrTiO₃ and Fe₂O₃ particles contacted well. Further research revealed that the calcination temperature is an important factor in the preparation of the composite powder with relatively high photocatalytic ability.     

Bifunctional photocatalysis of TiO2/Cu2O composite under visible light: Ti in organic pollutant degradation and water splitting

Photocatalytic experiment results under visible light demonstrate that both TiO₂ and Cu₂O have low activity for brilliant red X-3B degradation and neither can produce H₂ from water splitting. In comparison, TiO₂/Cu₂O composite can do the both efficiently. Further investigation shows that the formation of Ti³⁺ under visible light has great contribution. The mechanism of photocatalytic reaction is proposed based on energy band theory and experimental results. The photogenerated electrons from Cu₂O were captured by Ti⁴⁺ ions in TiO₂ and Ti⁴⁺ ions were further reduced to Ti³⁺ ions. Thus, the photogenerated electrons were stored in Ti³⁺ ions as the form of energy. These electrons trapped in Ti³⁺ can be released if a suitable electron acceptor is present. So, the electrons can be transferred to the interface between the composite and solution to participate in photocatalytic reaction. XPS spectra of TiO₂/Cu₂O composite before and after visible light irradiation were carried out and provided evidence for the presence of Ti³⁺. The image of high-resolution transmission electron microscopy demonstrates that TiO₂ combines with Cu₂O tightly. So, the photogenerated electrons can be transferred from Cu₂O to TiO₂.     

The effects of activated carbon supports on the structure and properties of TiO2 nanoparticles prepared by a sol-gel method

TiO₂-coated activated carbon (TiO₂/AC) composites and pure TiO₂ powders were prepared by a sol-gel method using tetrabutylorthotitanate as a precursor. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), differential thermal analysis (DTA), X-ray photoelectron spectrum (XPS) and nitrogen absorption. The photoactivity of samples was evaluated by methylene blue (MB) degradation. The analysis results show that compared with pure TiO₂ powders, the spherical-shaped TiO₂ particles are well-dispersed in the AC matrix and the size of the resulting TiO₂ crystallites decreases to below 40 nm with increasing phase transformation temperature. The AC matrix creates anti-calcination effects and shows interfacial energy effects that control the growth of the TiO₂ particles, baffle the anatase to rutile phase transition, and cumber the TiO₂ particles to agglomerate. Compared with the surface areas of TiO₂ powders, the combination of TiO₂ and AC forms composites with high surface areas which are slightly affected by calcination temperature. By AC support, the photoactivity of TiO₂ is increased in MB photocatalytic course, possible because active carbon increases photocatalytic activity of TiO₂ particles by producing high concentration of organic compound near TiO₂, and small-size TiO₂ particles are well-dispersed on the surface of AC.     

Design and fabrication of a TiO2/nano-silicon composite visible light photocatalyst

Nano-silicon (nc-Si) was utilized as the charges generator to promote the photocatalytic and super-hydrophilic reactivity of TiO₂ film under visible light irradiation. The photocatalytic ability of TiO₂/nc-Si composite photocatalyst was evaluated by a set of experiments to photodecompose 100 ppm methylene blue (MB) in aqueous solution. And the super-hydrophilic property was characterized by measuring the water droplet contacts angle, under visible light irradiation in atmospheric air and at room temperature. Under 100 mW/cm² visible light irradiation, the droplet contact angles were reduced to 0° within 4 h with nc-Si charge generator. Additionally, the rate constant of MB photo-degradation was promoted 6.6 times.     

镧掺杂介孔TiO2光催化剂的制备、表征及其光催化性能

以钛酸四正丁酯和硝酸镧为原料, 以P123为模板剂,采用模板法合成了La掺杂型介孔TiO₂光催化剂, 借助TGA-DSC、BET、XRD及UV-Vis等测试手段对样品进行了表征,并以苯酚为模型污染物考察了镧掺杂量对样品光催化活性的影响．结果表明: La掺杂介孔TiO₂光催化剂孔径分布较均匀(～10 nm),比表面积可达165 m²/g．与纯介孔TiO₂相比,经掺杂改性后的样品在紫外光区及可见光区的吸收显著增强,对光具有更高的利用率,La掺杂可显著提高介孔TiO₂的光催化活性.     

Synthesis and characterization of bamboo-like CdS/TiO<Subscript>2</Subscript> nanotubes composites with enhanced visible-light photocatalytic activity

In order to efficiently use the visible light in the photocatalytic reaction, a novel bamboo-like CdS/TiO₂ nanotubes composite was prepared by a facile chemical reduction method, in which CdS nanoparticles located in the TiO₂ nanotubes. The composition and structure of this nanocomposite were characterized by TEM, HRTEM, XRD, XPS, FTIR and UV-vis spectroscopy. This CdS/TiO₂ nanotubes composite exhibited much higher visible-light photocatalytic activity for the degradation of methylene blue than pure TiO₂ nanotubes and CdS nanoparticles, and the highest photodegradation efficiency after 6 h irradiation can reach 84.5%. It is inferred that the unique structure of CdS/TiO₂ nanotubes composites acts an important role for the improvement of their photocatalytic activity.     

Evolution of TiO2 coating layers on lamellar sericite in the presence of La and the pigmentary properties

TiO₂-coated sericite powders were prepared by the chemical deposition method starting from lamellar sericite and TiCl₄ in the presence or absence of La³⁺ cations. After calcination at 900 °C for 1 h, the resultant TiO₂ nanoparticles on the sericite surfaces existed in anatase phase. The light scattering indexes of the TiO₂-coated lamellar sericite powders were dozens of times higher than that of the naked lamellar sericite powders. The presence of La³⁺ in the deposition solution was beneficial to the formation of the small-sized anatase TiO₂ nanoparticles, resulting in the formation of the dense and uniform island-like TiO₂ coating layers in a large range of the weight ratios of TiO₂ to sericite from 5% to 20%. The TiO₂-coated lamellar sericite powders prepared in the presence of La³⁺ had higher light scattering index than that prepared in the absence of La³⁺. XPS analysis shows that when La³⁺ cations were absent in the reaction solution, TiO₂ coating layers anchored at the sericite surface via the Ti-O-Si and Ti-O-Al bonds. The presence of La³⁺ cations caused the formation of Si-O-La and Al-O-La bonds at the sericite surface and Ti-O-La bond at the surface of TiO₂ coating layers. After coating TiO₂ on the sericite surface, the yellowness of the TiO₂-coated sericite powders obviously increased and the brightness slightly decreased.     

Efficient visible-light-induced photocatalytic degradation of MO on the Cr-nanocrystalline titania-S

In order to improve visible light photocatalytic activities of the nanometer TiO₂, a novel and efficient Cr,S-codoped TiO₂ (Cr-TiO₂-S) photocatalyst was prepared by precipitation-doping method. The crystalline structure, morphology, particle size, and chemical structure of Cr-TiO₂-S were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and Fourier transform infrared (FT-IR) techniques, respectively. Results indicate that the doping of Cr and S, cause absorption edge shifts to the visible light region (λ > 420 nm) compare to the pure TiO₂, reduces average size of the TiO₂ crystallites, enhances desired lattice distortion of Ti, promotes separation of photo-induced electron and hole pair, and thus improves pollutant decomposition under visible light irradiation. The photocatalytic activities of Cr-TiO₂-S nanoparticles were evaluated using the photodegradation of methyl orange (MO) as probe reaction under the irradiation of UV and visible light and it was observed that the Cr-TiO₂-S photocatalyst shows higher visible photocatalytic activity than the pure TiO₂. The optimal Cr-TiO₂-S concentration to obtain the highest photocatalytic activity was 5 mol% for both of Cr and S.     

Yellow phosphors coated with TiO2 for the enhancement of photoluminescence and thermal stability

In order to improve the phosphor efficiency of yellow emission of the phosphor-converted white light emitting diode (pcW-LED), the Ba²⁺ Mg²⁺ co-doped Sr₂SiO₄:Eu phosphors were synthesized and were coated with thin and uniform TiO₂. The TiO₂ layer with 20 nm was uniformly coated over the phosphor surface. The photoluminescence (PL) properties of the TiO₂-coated phosphors showed improved yellow-emission intensity compared to the pristine phosphors. The temperature dependence of photoluminescence was measured from 25 to 150 °C. The TiO₂-coated phosphors showed superior thermal quenching property compared to pristine phosphors. We concluded that the TiO₂-coated surface of the phosphor is an effective way to improve the phosphor efficiency and enhance the thermal quenching stability.     

Visible-light-activated Ce-Si co-doped TiO2 photocatalyst

To enhance the visible photocatalytic activity and thermal stability of TiO₂, Ce-Si co-doped TiO₂ materials were synthesized through a nonaqueous method of which the purpose was to reduce the aggregation between TiO₂ particles. The obtained materials maintained anatase phase and large surface area of 103.3 m² g⁻¹ even after calcined at 800 °C. The XPS results also indicated that Si was weaved into the lattice of TiO₂, and Ce mainly existed as oxides on the surface of TiO₂ particles. The doped Si might enhance surface area and suppress transformation from anatase to rutile, while the doped Ce might cause visible absorption and inhibit crystallite growth during heat treatment. Evaluated by decomposing dye Rhodamine B, visible photocatalytic activity of Ce-Si co-doped TiO₂ was obviously higher than that of pure TiO₂ and reached the maximum at Ce and Si contents of 0.5 mol% and 10 mol%.     

Rare earth oxide-doped titania nanocomposites with enhanced photocatalytic activity towards the degradation of partially hydrolysis polyacrylamide

Rare-earth oxide-doped titania nanocomposites (RE³⁺/TiO₂, where RE = Eu³⁺, Pr³⁺, Gd³⁺, Nd³⁺, and Y³⁺) were prepared by a one-step sol-gel-solvothermal method. The products exhibited anatase phase structure, mesoporosity, and interesting surface compositions with three oxygen species and two titanium species. The products were used as the photocatalysts to degrade a partially hydrolysis polyacrylamide (HPAM) under UV-light irradiation, a very useful polymer in oil recovery. For comparison, Degussa P25 and as-prepared pure TiO₂ were also tested under the same conditions. The enhanced photocatalytic activity was obtained on as-prepared Eu³⁺ (Gd³⁺, Pr³⁺)/TiO₂ composites, and the reasons were explained. Finally, the degradation pathway of HPAM over the RE³⁺/TiO₂ composite was put forward based on the intermediates produced during the photocatalysis procedure.     

TiO2/carboxylate-rich porous carbon: A highly efficient visible-light-driven photocatalyst based on the ligand-to-metal charge transfer (LMCT) process

A novel visible-light-driven photocatalyst based on TiO₂/carboxylate-rich porous carbon composite (TiO₂/CRPC) was successfully synthesized by low temperature carbonization process in air. Sodium gluconate plays a crucial role in the formation of TiO₂/CRPC. Different functional groups of sodium gluconate play synergetic roles in the formation of TiO₂/CRPC. XRD and Raman spectra studies indicated that there are two different TiO₂ crystalline phases existing in TiO₂/CRPC, which are anatase and brookite, and the CRPC is amorphous. Via FT-IR and XPS spectra investigations, it was demonstrated that carboxylate group, the ligand-to-metal charge transfer (LMCT) forming functional group, was solidified into the CRPC and form the LMCT complex on TiO₂ surface through the fabrication of TiO₂/CRPC. Compared with the pure TiO₂, TiO₂/CRPC exhibit enhanced absorption in the UV and visible light region around 260–600 nm. The strong absorption in the visible light region gives TiO₂/CRPC advantages over pure TiO₂ for the degradation of organic pollutants. TiO₂/CRPC can activate O₂ in air under mild conditions and exhibit excellent visible-light-driven photocatalytic activities. However, TiO₂/C composite obtained by using glucose instead of sodium gluconate exhibits poor photocatalytic activity, which demonstrated that carboxylate–TiO₂ complexes are responsible for the prominent photocatalytic properties of TiO₂/CRPC under visible light irradiation.     

Enhanced photocatalytic activity and stability of nano-scaled TiO2 co-doped with N and Fe

Titanium dioxide (TiO₂) nanoparticles co-doped with N and Fe were prepared via modified sol-gel process. The products were characterized by transmission electron microscopy (TEM), N₂ adsorption, X-ray diffraction (XRD), Raman spectroscopy, UV-vis spectroscopy, photoluminescence (PL), and X-ray photoelectron spectroscopy (XPS). It is shown that the prepared TiO₂ particles were less than 10 nm with narrow particle size distribution. The addition of MCM-41 caused the formation of Ti-O-Si bond which fixed the TiO₂ on MCM-41 surface, thus restricted the agglomeration and growth of TiO₂ particles. The photocatalytic performance in the degradation of methylene blue showed that N, Fe co-doped TiO₂ exhibited much higher photocatalytic activity than doped sample with nitrogen or Fe³⁺ alone under both UV and visible light. N, Fe co-doping decreased the loss of doping N during the degradation reaction, thus increased the photocatalytic stability. It was also found that the nitridation time had significant influence on the photocatalytic activity of prepared TiO₂ catalysts.     

Nitrogen doped TiO2 nanoparticles decorated on graphene sheets for photocatalysis applications

Nitrogen doped TiO₂ nanoparticles decorated on graphene sheets are successfully synthesized by a low-temperature hydrothermal method. The resulting GR-N/TiO₂ composites are characterized by X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), X-Ray photoelectron spectroscopy (XPS) and Transmission Electron Microscopy (TEM). The optical properties are studied using UV–visible diffuse reflectance spectroscopy (DRS), which confirms that the spectral responses of the composite catalysts are extended to the visible-light region and show a significant reduction in band gap energy from 3.18 to 2.64 eV. Photoluminescence emission spectra verify that GR-N/TiO₂ composites possess better charge separation capability than pure TiO₂. The photocatalytic activity is tested by degradation of methyl orange (MO) dye under visible light irradiation. The results demonstrate that GR-N/TiO₂ composites can effectively photodegrade MO, showing an impressive photocatalytic enhancement over pure TiO₂. The dramatically enhanced activity of composite photocatalysts can be attributed to great adsorption of dyes, enhanced visible light absorption and efficient charge separation and transfer processes. This work may provide new insights into the design of novel composite photocatalysts system with efficient visible light activity.     

Different effects of cerium ions doping on properties of anatase and rutile TiO2

Pure and Ce⁴⁺ doped anatase and rutile TiO₂ were prepared by hydrothermal methods and characterized by XRD, TEM, UV-vis diffusion spectroscopy, and XPS measurements. The photocatalytic reactivity of the catalysts was evaluated by the photodegradation of Rhodamine B (RB) under ultraviolet irradiation. The photocatalytic efficiency of the rutile sample doped with an appropriate amount of Ce⁴⁺ was enhanced while all Ce⁴⁺ doped anatase samples showed a much lower activity than pure anatase. The reasons were discussed     

Doping mode, band structure and photocatalytic mechanism of B-N-codoped TiO2

The photocatalyst B and N codoped TiO₂ (B-N-TiO₂) was prepared via the sol-gel method by using boric acid and ammonia as B and N precursors. The doping mode, band structure and photocatalytic mechanism of B-N-TiO₂ were investigated well and elucidated in detail. B-N-TiO₂ showed the narrowed band gap and thus extended the optical absorption due to interstitial N and [NOB] species in the TiO₂ crystal lattice. The coexistence of interstitial N and [NOB] species in the TiO₂ crystal lattice and surface NO_x species allowed the more efficient utilization of visible light. Simultaneously, interstitial [NOB] and N species and surface B₂O₃ and NO_x species facilitated the separation of photo generated electrons and holes and suppress their recombination effectively. Hence, B-N-TiO₂ showed a higher photocatalytic activity than pure TiO₂, N-doped TiO₂ (N-TiO₂) and B-doped TiO₂ (B-TiO₂) under both UV and visible light irradiation.     

Preparation and characterization of TiO2 photocatalysts co-doped with iron (III) and lanthanum for the degradation of organic pollutants

Titanium dioxide photocatalysts co-doped with iron (III) and lanthanum were prepared by a facile sol-gel method. The structure of catalysts was characterized by X-ray diffraction (XRD), Raman spectroscopy, UV-vis diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the samples were evaluated by the degradation of methylene blue in aqueous solutions under visible light (λ > 420 nm) and UV light irradiation. Doping with Fe³⁺ results in a lower anatase to rutile (A-R) phase transformation temperature for TiO₂ particles, while doping with La³⁺ inhibits the A-R phase transformation, and co-doping samples indicate that Fe³⁺ partly counteracts the effect of La³⁺ on the A-R transformation property of TiO₂. Fe-TiO₂ has a long tail extending up the absorption edges to 600 nm, whereas La-TiO₂ results in a red shift of the absorption. However, Fe and La have synergistic effect in the absorption of TiO₂. Compared with Fe³⁺ and La³⁺ singly doped TiO₂, the co-doped simple exhibits excellent visible light and UV light activity and the synergistic effect of Fe³⁺ and La³⁺ is responsible for improving the photocatalytic activity.     

Synergetic Photocatalytic Nanostructures Based on Au/TiO2/Reduced Graphene Oxide for Efficient Degradation of Organic Pollutants

Recently, there is crucial interest in the design and fabrication of nanocatalysts for efficient decomposition of organic pollutants in wastewater using visible light. This work reports the assembling fabrication of synergetic photocatalytic Au/TiO₂/RGO nanostructures by utilizing the reduced graphene oxide (RGO) as substrate material and efficient separator for electrons and holes. The Au/TiO₂ nanostructures with a ≈7 nm TiO₂ particles size are dispersed uniformly on RGO nanosheets. UV–vis diffuse reflectance spectroscopy verifies that Au/TiO₂/RGO nanocomposites show strong absorption of visible light. The degradation efficiency after 1 h for hydroquinone under visible light and UV light is ≈77% and ≈90%, respectively. Under visible light, the calculated apparent rates (k ) of the Au/TiO₂/RGO nanocomposites are 0.0112 and 0.0174 min^?1 for decomposition of methylene blue and hydroquinone. That are five times greater than that of bare TiO₂. The high photocatalytic activity is mainly attributed to the synergy between RGO and Au/TiO₂ nanostructure. The strategy of composite nanostructures assembling on RGO is ensured to have a great practicable potential for the designing of high efficient multielement composite nanoparticles catalysts.