Continuous True-Time-Delay System Employing a Novel Tunable Chirped Fiber Grating Delay Line and a Sampled Grating Based Multiwavelength Fiber Laser

A photonics true-time-delay system for phased array antenna beam steering employing a novel tunable chirped fiber grating delay line and a multi-wavelength erbium-doped fiber ring laser source based on a sampled grating filter is proposed. The tunable chirped fiber grating, which act as a continuous time-delay element, is achieved by bending a uniform fiber Bragg grating bonded at a slant onto the lateral surface of a simply supported beam. This technique allows the dynamic control of the chirp rate and spectral width of the grating without center wavelength shift. By adjusting the chirp rate of the fiber grating via bend strain, this kind of tunable chirped fiber grating could achieve very low and adjustable delay times, therefore provides higher angle resolution for scanning microwave beam, even the wavelengths of laser source are fixed and un-tunable. The true-time-delay system using proposed tunable chirped fiber grating delay element and sampled grating based laser source is constructed and demonstrated experimentally.     

Tunable Chirped Fiber Grating Based Variable Time-Delay Network for Phased-Array Antenna Beamforming

In this paper, we present a photonics continuous beamforming system for optically controlled phased-array antenna based on a tunable fiber ring laser source and a novel variable true-time delay network consisting of one single-mode fiber delay line and four tunable chirped grating delay lines. The chirp rate of each chirped grating is tuned by bending a uniform fiber Bragg grating (FBG) bonded at a slant onto the lateral surface of a simply supported beam. This kind of variable true-time delay network can provide five-channel time-delayed signals that can be fed to an antenna array to achieve continuously beam scanning. The proposed true-time-delay unit with 5-element phased array steerer is suitable for phased-array antenna beamforming at frequencies up to 12 GHz.     

All-optical microwave notch filter with flat passband based on semiconductor optical amplifier

An all-optical filter structure for interference mitigation of microwave signals is proposed and demonstrated. The structure is based on a recirculating delay line loop (RDLL) and a fiber Bragg grating. The RDLL is comprised of a semiconductor optical amplifier (SOA) followed by a tunable narrowband optical filter and an optical variable delay line. Negative tap is generated using wavelength conversion based on the cross-gain modulation of amplified spontaneous emission spectrum of the SOA. A negative band-pass filter and a broadband all-pass filter are synthesized to achieve a narrow notch filter with flat passband which can excise interference with minimal impact on the wanted signal over a wide microwave range. Experimental results show the notch rejection ratio of 30 dB, good shape factor and tunability.     

High-Accuracy Measurement of the Dispersion of Chirped Fiber Gratings

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｆｉｂｅｒｇｒａｔｉｎｇｓａｒｅｐｒｏｖｅｄｔｏｂｅｏｎｅｏｆｔｈｅｍｏｓｔｉｍｐｏｒｔａｎｔｒｅｃｅｎｔｄｅｖｅｌｏｐｍｅｎｔｓｉｎｔｈｅｆｉｅｌｄｏｆｏｐｔｉｃａｌｆｉｂｅｒｔｅｌｅｃｏｍｍｕｎｉｃａｔｉｏｎｓａｎｄｓｅｎｓｉｎｇ .Ｔｈｅｙａｒｅｌｉｋｅｌｙｔｏｈａｖｅａｐｐｌｉｃａｔｉｏｎｉｎｔｗｏｍａｉｎａｒｅａｓ:ｄｉｓｐｅｒｓｉｏｎｃｏｍｐｅｎｓａｔｉｏｎｉｎｌｏｎｇ ｈａｕｌｆｉｂｅｒｎｅｔｗｏｒｋｓ[1,2 ]ａｎｄｗａｖｅｌｅｎｇｔｈｒｏｕｔｉｎｇｉｎｗ…     

采用光纤光栅级联结构实现光纤延迟线

在使用光纤光栅实现皮秒级别时延的基础上,提出一种光纤光栅与单模光纤相结合的微秒级别级联结构,该结构可以实现中心波长1 550~1 553 nm范围内,间距为1 nm的窄波长反射型时延线,共1,1.5,2和2.5 μs四种不同的时延。将单波长反射的啁啾布拉格光纤光栅与103 m单模光纤连接构成延迟单元,再利用光环形器将4个延迟单元级联并使用内半径为3 cm的光纤绕线盘,将四种延时单元的传输光纤进行整合。借助光纤光栅的反射镜作用,控制不同波长光信号通过不同的传输距离,从而达到时延目的。本文通过对啁啾布拉格光纤光栅的反射谱进行仿真分析,发现相邻反射谱的旁瓣会出现交叠现象,因此使用六个切趾函数对旁瓣滤除。结果显示：不同切趾函数的滤除效果也不同,能够完全滤除旁瓣并且对反射谱包络影响最小的是柯西切趾函数,经柯西切趾后能使不同波长光信号在对应中心波长1 nm范围内反射率达到1,而其他位置均为0。由于使用光纤绕线盘整合延迟单元传输光纤会产生一定损耗,因此对弯曲损耗进行仿真分析,结果表明：弯曲半径相同时,损耗与工作波长成正比;工作波长相同时,弯曲损耗与弯曲半径成反比。当弯曲半径大于2.9 cm时,弯曲损耗曲线变化平缓并趋于0,因此当光纤绕线盘内半径为3 cm时保证了在减小延迟模块体积的同时又不会有过大的损耗。通过TDS784D型示波器对频率为2 000 Hz的信号经不同传输距离后的波形进行测试,结果显示经3 m和5 km传输线后信号的各项参数基本保持不变,经过长距离传输后,依然能保持原信号特性,因此使用103 m传输线可达到延迟目的。使用W-GGL型光功率计对不同频率下的输出功率进行测量,与直光纤的输出功率相比,当弯曲半径为2~3 cm时偏差较大,等于3 cm时偏差为0.18 dBm,大于3 cm时则无限趋近,因此设置绕线盘内半径为3 cm符合光纤延迟线的损耗范围。     

Optically controlled tunable dispersion compensators based on pumped fiber gratings

We demonstrate optically tunable dispersion compensators based on pumping fiber Bragg gratings made in Er/Yb codoped fiber. The tunable dispersion for a chirped grating and also a uniform-period grating was successfully demonstrated in the experiment. The dispersion of the chirped grating was tuned from 900 to 1990 ps/nm and also from -600 to -950 ps/nm in the experiment.     

40Gb/s光时分复用传输光纤光栅补偿色散研究

用精密扫描掩模法写入宽阻带啁啾光纤光栅,掩模板背面两端各10％长度处镀有按4阶高斯函数透过率的膜,写入的啁啾光栅的时延纹波最大值为20ps。为减少写入光纤光栅的偏振模色散,研制了新的低偏振模色散光纤光栅补偿写入法。采用补偿写入法前的平均微分群时延为9．1406 ps;采用补偿写入法后的平均微分群时延为0．1521 ps。并利用低偏振模色散光纤光栅对40Gb／s光时分复用系统在普通G．652光纤传输122km的色散进行了补偿实验,功率代价为1．5dB。     

Experimental demonstration and cascadability analysis of a tunable optical buffer based on a re-circulating loop consisting of optical SSB modulator and FBG filter

We demonstrate a tunable optical buffer with variable time delays for label switching applications using an optical single sideband modulator in a fiber Bragg grating-filter loop. This optical buffer realizes payload storage with optional wavelength conversion function, providing flexibility in packet router design. Small sensitivity penalty is observed in our experiment after the payload circulating in the buffer loop three times. The cascadability of the tunable optical buffer is investigated. We provide analysis of the optical signal to noise ratio degradation due to accumulated amplified spontaneous emission noise, and the penalty caused by loss ripple and group delay ripple of the fiber Bragg grating.     

光纤光栅传感信号解调技术研究进展

光纤光栅传感器是一种新型传感器,有着非常广泛的应用前景。限制光纤光栅传感器大量实际应用的主要障碍是传感信号解调,因而,光纤光栅传感信号解调是光纤光栅传感器应用的关键技术之一。本文对现有已报道的光纤光栅传感信号的解调方法进行综述,并归类为:边缘滤波法、匹配滤波法、可调谐滤波法、光源波长可调谐扫描法、射频探测法、光栅啁啾法、CCD分光仪法、干涉法。对各种方法的原理及相关改进方法进行了阐述,并对其优缺点做了比较分析,最后,对光纤光栅传感信号的解调技术发展进行了展望。     

Magneto-Optic Fiber Gratings Useful for Dynamic Dispersion Management and Tunable Comb Filtering

Intelligent control of dispersion management and tunable comb filtering in optical network appfications can be performed by using magneto-optic fiber Bragg gratings （MFBGs）. When a nonuniform magnetic field is applied to the MFBG with a constant grating period, the resulting grating response is equivalent to that of a conventional chirped grating. Under a linearly nonuniform magnetic field along the grating, a linear dispersion is achieved in the grating bandgap and the maximal dispersion slope can come to 1260ps/nm2 for a l0-mm-long fiber grating at 1550nm window. Similarly, a Gaussian-apodizing sarnpled MFBG is also useful for magnetically tunable comb filtering, with potential application to clock recovery from return-to-zero optical signals and optical carrier tracking.     

Generation of an arbitrary chirped microwave waveform with high time-bandwidth product for increasing range resolution of RADAR by using photonic technique

An approach for photonic generation of an arbitrary chirped microwave waveform with an increased time-bandwidth product (TBWP) is proposed and experimentally demonstrated. In the proposed model, light from the mode locked laser is splitted into two parts by using 1 × 2 power splitter: one is sent to linearly chirped fiber Bragg grating (LCFBG) through circulator and the other is time delayed by fiber delay line. The optical pulse in upper arm is time stretched by the LCFBG. Meanwhile, the optical pulse in lower arm experiences a time delay and then stretched by the dispersive single mode fiber. Temporal interference pattern is generated with an increasing or decreasing free spectral range by combination of two time-stretched optical pulses. Finally, the temporal interference pattern which is obtained at the output of optical coupler is transformed into an arbitrary chirped microwave waveform by using a photo-detector. The main advantage of this proposed model is high TBWP in the range of 750–1000 which ultimately results in an increased range resolution of radio detection and ranging.     

Fiber Bragg gratings for dispersion compensation in optical communication systems

This paper presents an overview of fiber Bragg gratings (FBGs) fabrication principles and applications with emphasis on the chirped FBG used for dispersion compensation in high-speed optical communication systems. We discuss the range of FBG parameters enabled by current fabrication methods, as well as the relation between the accuracy of FBG parameters and the performance of FBG-based dispersion compensators. We describe the theory of the group delay ripple (GDR) generated by apodized chirped fiber gratings using the analogy between noisy gratings and superstructure Bragg gratings. This analysis predicts the fundamental cutoff of the high frequency spatial noise of grating parameters in excellent agreement with the experimental data. We review the iterative GDR correction technique, which further improves the FBG quality and potentially enables consistent fabrication of FBG-based dispersion compensators and tunable dispersion compensators with unprecedented performance.     

Analytical performance evaluation of an adjustable PMD compensator using high-birefringence linearly chirped FBG

System performance of a high-speed WDM transmission system in the presence of PMD can be improved significantly by using an adjustable PMD compensator. We have analytically evaluated the performance of a tunable PMD compensator based on high-birefringence linearly chirped fiber Bragg grating. The device can adjust differential group delay in a linearly continuous way without affecting the wavelength outside the bandwidth. Various properties of the device such as relative group delay, differential group delay, reflectivity, etc. are investigated in terms of wavelength and grating length. Results show that under stretched condition the device generates a time delay between fast and slow polarization axes, which is adjustable from 0 to 55 ps and is tunable within 2.4 nm wavelength range.     

Tunable microwave photonic notch filter using a dual-wavelength fiber laser with phase modulation

A novel tunable microwave photonic notch filter using a phase-modulated dual-wavelength fiber laser is presented. A stable dual-wavelength erbium-doped fiber laser with a linear cavity is formed by a polarization-maintaining uniform fiber Bragg grating (PM-FBG) and a polarization maintaining linearly chirped fiber Bragg grating (PM-LCFBG), both of which were fabricated on a high-birefringence (Hi-Bi) fiber. It is found that a stable room-temperature dual-wavelength operation can be achieved due to the presence of two reflection peaks arising from the orthogonal states of polarization (SOP) of the PM-FBG. Experimental results show stable dual-wavelength lasing operation with a wavelength separation of ∼0.36 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. The dual-wavelength fiber laser is combined with a phase modulator and a segment of single-mode fiber (SMF) as a dispersive device to form a tunable microwave photonic notch filter. By stretching the PM-FBG to tune the wavelength separation of the dual-wavelength fiber laser, a tunable microwave photonic notch filter with various free spectral ranges (FSRs) and a rejection ratio greater than 35 dB was developed.     

Multiple-bipolar-tap tunable spectrum sliced microwave photonic filter

A spectrum sliced microwave photonic signal processor structure, which is all-fiber based and features simplicity, together with the ability to realize tunability, reconfigurability, bipolar taps, and multiple-tap rf filtering, is presented. It is based on thermally controlled optical slicing filters induced into two linearly chirped fiber Bragg gratings. Experimental results demonstrate the realization of versatile microwave photonic filters with frequency tunable, reconfiguration, and bipolar-tap generation capabilities.     

Millimeter-wave pulse generation based on pulse reshaping using superstructure fiber Bragg grating

A novel optical approach is proposed to generate millimeter wave (MMW) pulse signal based on the pulse reshaping of superstructure fiber Bragg grating (SSFBG). In our scheme, one input pico-second Gaussian pulse is transformed into n Gaussian pulses by the SSFBG reshaping firstly, and then the pulse train is replicated to form a required frequency modulation MMW optical pulse envelope by the linear chirped fiber Bragg grating (LCFBG) or other highly dispersive element. The high-speed photodetector (PD) and band-pass filter can transform the MMW optical pulse into an MMW pulse signal ultimately. Depending on this scheme, MMW signals with frequency up to 10 GHz can be easily generated by the completed fiber components.     

Highly efficient tunable fiber Bragg grating filters using multilayer piezoelectric transducers

We realized a wavelength tunable optical filter based on a fiber Bragg grating using multilayer piezoelectric transducers (MLP). The Bragg wavelength of the filter can be easily tuned in proportion to an applied low DC voltage. The tuning range efficiency was as high as 0.2 nm/V. We realized a 10 nm Bragg wavelength shift by applying as low as 50 V to the MLP. The MLP was also used in a higher order dispersion equalizer which consists of a pair of nonlinearly chirped gratings. A zero dispersion wavelength shift of 7 nm was successfully realized for the equalizer.     

Amplification of optical delay by use of matched linearly chirped fiber Bragg gratings

We describe the use of a matched linearly chirped fiber Bragg grating (FBG) pair as a key element in an adjustable optical delay line. This delay line has the unique property that the achievable optical group delay is orders of magnitude greater (factor of 10(2) in our experiment) than the actual physical displacement. We demonstrate operation of such an optical delay line over a delay range of 3.5 mm using a pair of matched 1300-nm chirped FBGs with a bandwidth of 20 nm each.     

基于半导体光放大器和受激布里渊散射的全光非归零码时钟提取

利用半导体光放大器(SOA)的增益饱和特性、自相位调制(SPM)效应和啁啾光纤光栅(CFBG)的滤波和啁啾特性共同作用实现了10 Gbit/s非归零码(NRZ)信号的时钟分量增强。经过该结构的非归零光谱的时钟分量增强后,其时钟数据抑制比提高了12.9 dB。时钟分量增强后的信号经基于受激布里渊效应(SBS)的时钟提取结构后实现了对非归零信号的全光时钟提取。这种新型非归零全光时钟提取结构具有对数据速率及数据格式透明,低抖动,不受码型效应的影响等优点。     

Photonic generation of tunable microwave signals by beating a dual-wavelength single longitudinal mode fiber ring laser

A novel method of generating tunable microwave signals in the photonic domain is proposed. Eighteen pairs of stable dual-wavelength single longitudinal mode lasings are achieved by incorporating a fiber Bragg grating based Fabry–Pérot filter and a tunable fiber grating into a fiber ring cavity. The frequency of the generated microwave signal obtained by beating the dual-wavelength laser with a photodetector can be tuned simply through configuring the working wavelength of the laser. A series of microwave frequencies of 9.4885, 9.572, 9.7111, 9.8498, 9.9598 and 10.0712 GHz are generated experimentally. The proposed method is useful in applications such as wireless access networks, sensor networks, radio-over-fiber systems and software-defined radio. PACS 41.20.-q; 42.55.Wd; 41.81.-i