Reduction of acoustic radiation by impedance control with a perforated absorber system

A model of sound radiation from an infinite plate with an absorptive facing is proposed and investigated theoretically from the viewpoint of acoustic power. Acoustic characteristics on the plate surface are represented by impedance derived from iso-absorption curves. A parametric study is carried out to clarify the effect of the impedance on the acoustic power. Results derived from this model show that acoustic radiation depends on change in impedance as well as the absorption coefficient, and there is a possibility of reducing the radiation from vibrating surface by introducing an appropriate impedance surface. In order to realize this effect, a model using a perforated board with a back cavity attached to the vibrating surface is proposed, in which the motion of the perforated board is made equal to that of the vibrating surface. To obtain fundamental data, a theoretical study is performed under a simplified condition, assuming an infinite plane piston. The calculated results are compared to experimental data measured by using an acoustic tube. The results, which are in good agreement in the reduction effect, show that this system can achieve the reduction of radiated sound power at arbitrary frequencies.     

介质窗横向电磁场分布下的次级电子倍增效应

本文利用自编P3D3V PIC程序, 数值研究了BJ32矩波导传输TE₁₀模式高功率微波在介质窗内、 外表面引发的次级电子倍增过程, 给出了次级电子3维空间位置分布特征、介质窗表面法向静电场分布规律以及电子数密度分布特性. 模拟结果表明: 对于介质窗内侧, 微波强场区域率先进入次级电子倍增过程; 而对于介质窗外侧, 则是微波弱场区域优先进入次级电子倍增过程. 形成机理可以解释为: 微波坡印廷矢量方向与介质窗外表面法向相同而与内表面法向相反, 内侧漂移运动导致强场区域电子易于被推回表面, 有利于次级电子倍增优先形成; 外侧漂移运动导致强场区域电子易于被推离表面, 不利于次级电子倍增形成. 准3维模型相对1维模型: 介质窗内侧次级电子倍增过程中, 次级电子倍增进入饱和时间长、饱和次级电子数目少、平均电子能量高、 入射微波功率低、沉积功率低; 介质窗外侧次级电子倍增过程中, 次级电子倍增进入饱和时间短、饱和次级电子数目少、平均电子能量低、 入射微波功率低、沉积功率低. 沉积功率与入射微波功率比值与微波模式、强度及介质窗内外侧表面关系不大, 准3维和1维模型计算结果均在1%–2%左右水平. 关键词： 高功率微波 介质表面次级电子倍增 粒子模拟 横向电磁场分布     

An experimental method for making spectral emittance and surface temperature measurements of opaque surfaces

An experimental procedure has been developed to make spectral emittance and temperature measurements. The spectral emittance of an object is calculated using measurements of the spectral emissive power and of the surface temperature of the object obtained using a Fourier transform infrared (FTIR) spectrometer. A calibration procedure is described in detail which accounts for the temperature dependence of the detector. The methods used to extract the spectral emissive power and surface temperature from measured infrared spectra were validated using a blackbody radiator at known temperatures. The average error in the measured spectral emittance was 2.1% and the average difference between the temperature inferred from the recorded spectra and the temperature indicated on the blackbody radiator was 1.2%. The method was used to measure the spectral emittance of oxidized copper at various temperatures.     

Investigations on the effect of process parameters on the growth of vertically oriented graphene sheet in plasma-enhanced chemical vapour deposition system

A multistage numerical model comprising the plasma kinetics and surface deposition sub-models is developed to study the influence of process parameters, namely, total gas pressure and input plasma power on the plasma chemistry and growth characteristics of vertically oriented graphene sheets (VOGS) grown in the plasma-enhanced chemical vapour deposition system containing the Ar + H₂ + C₂H₂ reactive gas mixture. The spectral and spatial distributions of temperature and number densities, respectively, of plasma species, that is, charged and neutral species in the plasma reactor, are examined using inductively coupled plasma module of COMSOL Multiphysics 5.2 modelling suite. The numerical data from the computational plasma model are fed as the input parameters for the surface deposition model, and from the simulation results, it is found that there is a significant drop in the densities of various plasma species as one goes from the bulk plasma region to the substrate surface. The significant loss of the energetic electrons is observed in the plasma region at high pressure (for constant input power) and low input power (for constant gas pressure). At low pressure, the carbon species generate at higher rates on the catalyst nanoislands surface, thus enhancing the growth and surface density of VOGS. However, it is found that VOGS growth rate increases when input plasma power is raised from 100 to 300 W and decreases with further increase in the plasma power. A good comparison of the model outcomes with the available experimental results confirms the adequacy of the present model.     

The effect of discharge power density on polyethylene terephthalate film surface modification by dielectric barrier discharge in atmospheric air

Polyethylene terephthalate (PET) films are modified using non-equilibrium plasma generated by DBD in atmospheric air, and the effects of discharge power density on the surface modification are studied. It is found that increasing discharge power density can induce more effective treatment of PET films, because this leads to a faster decrease in water contact angle and a faster increase in surface energy due to more creation of polar groups and more obvious etching occurring on the PET surface. So the treatment time needed to achieve the same level of surface treatment can be reduced by increasing the discharge power density.     

Simulation for light power distribution of 3D InGaN/GaN MQW LED with textured surface

In this paper, we introduce a full 3D simulation for light power distribution of an InGaN/GaN MQW LED with a textured surface. Device simulation was performed with the APSYS software to get power distribution of light sources inside the LED. Based on this, ray tracing simulation was carried out to get light power distribution outside the LED. During the process of ray tracing, the textured surface was treated as a special material interface whose reflectivity, transmittance and refraction angle are obtained with a Finite-Difference Time-Domain (FDTD) method instead of using the usual Fresnel formulas for normal material interfaces. By comparing the ray tracing results with and without the textured surface, we found that the textured surface yields a smoother transmitted power distribution and greatly improved power extraction efficiency, which are comparable to experiment. These effects may be further improved by optimizing the texture geometry.     

Structural changes in tin oxide thin film with laser exposure

The effects of laser irradiation on the surface, structure and optical properties of SnO thin films deposited on glass substrates using electron beam evaporation, are investigated. The thin film samples are irradiated using fundamental beam at 1064 nm from Q-switched Nd:YAG pulsed laser with different power densities. Structural morphology of the film is investigated using XRD patterns and AFM image. Both XRD pattern and AFM image show increase in grain size of the film with increasing laser power density. Other optical phenomena, photoluminescence emission, transmission, refractive index determination and optical band gaps calculations are also carried out at various laser power densities. Results from all these investigations reveal expansion in grain size of the crystalline SnO thin film with increasing laser power density.     

高频调制大功率窄线宽分布反馈光纤激光器

研制了一种窄线宽光纤激光器.在有源相移光栅后加一段掺铒光纤,当用980 nm抽运光注入时,首先形成了分布反馈(DFB)光纤激光器,而残余抽运光将铒纤中铒离子从基态抽运到了激发态,对DFB激光实现了有效放大,实现了对残余抽运光的充分利用,节省了功耗、降低了成本;同时利用温控技术克服了DFB光纤激光器的温度敏感问题;将相移光栅黏贴于片状压电陶瓷(PZT)的表面实现了高频调制.实验研制的激光器的最高调制频率为2 kHz、输出功率为15.6 dBm,线宽为300 kHz. 关键词： 分布反馈光纤激光器 窄线宽 大功率 高频调制     

Depth-resolved profile of the magnetic field beneath the surface of a superconductor with a few nm resolution

The variation of a magnetic field as a function of depth beneath the surface of an YBa(2)Cu(3)O(7-delta) thin film in the Meissner state has been measured using low energy muons. The depth of implantation was varied from 20-150 nm by tuning the energy of the implanted muons from 3-30 keV. These are direct measurements of the penetration of a magnetic field beneath a superconducting surface which illustrate the power of low energy muons for near surface studies in superconductivity and magnetism.     

Electromagnetic effects on a molecule at a metal surface: I. Effects of nonlocality and finite molecular size

The electromagnetic effects on a molecule near a metal surface are considered with the view to understanding the surface-enhanced-Raman-scattering (SERS) effect. The image enhancement effect is calculated including the nonlocal response of the metal and finite molecular size. The effect is much reduced (× 10^?5) from that for a point molecule above a local metal but can still give a gain ≈ 10³. The power emitted by a dipole above a smooth surface is also calculated. For an Ag surface the power emitted in the form of photons, surface plasmons, and electron-hole excitations are found to be in the ratio 1 : 3 : 10⁶. The numerical results are calculated using the semi-classical infinite-barrier model of the metal surface with a Lindhard dielectric function modified to take into account finite electron lifetime and core polarization.     

Effect of RF power on the optical and morphological properties of RF plasma polymerised linalyl acetate thin films

Thin films derived from linalyl acetate were fabricated using the Radio Frequency (RF) plasma polymerisation technique between RF power levels of 10 and 75 W. The optical properties of the films were investigated using spectroscopic ellipsometry and UV-vis spectroscopy between 200 and 1000 nm. An optical band gap of approximately 3 eV for all power levels was determined from Tauc plots. The surface morphology and hardness of the material were studied using AFM and nano-indentation respectively to determine the effect of RF power on the thin film properties. Smooth surfaces with an average roughness of approximately 0.2 nm with consistent morphology were obtained across all power levels, while hardness demonstrated a linearly increasing dependence on RF deposition power, with values ranging between 0.29 and 0.44 GPa. These studies indicate the ability to tailor film characteristics by varying the RF deposition power, and the potential for the films to be used within electronic devices as encapsulation layers, insulating layers, or as semiconducting layers with the introduction of charge carriers to the chemical structure of the material.     

Quantification of high-power ultrasound induced damage on potato starch granules using light microscopy

A simple light microscopic technique was developed in order to quantify the damage inflicted by high-power low-frequency ultrasound (0-160 W, 20 kHz) treatment on potato starch granules in aqueous dispersions. The surface properties of the starch granules were modified using ethanol and SDS washing methods, which are known to displace proteins and lipids from the surface of the starch granules. The study showed that in the case of normal and ethanol-washed potato starch dispersions, two linear regions were observed. The number of defects first increased linearly with an increase in ultrasound power up to a threshold level. This was then followed by another linear dependence of the number of defects on the ultrasound power. The power threshold where the change-over occurred was higher for the ethanol-washed potato dispersions compared to non-washed potato dispersions. In the case of SDS-washed potato starch, although the increase in defects was linear with the ultrasound power, the power threshold for a second linear region was not observed. These results are discussed in terms of the different possible mechanisms of cavitation induced-damage (hydrodynamic shear stresses and micro-jetting) and by taking into account the hydrophobicity of the starch granule surface.     

Mechanisms of anode power deposition in a low pressure free burningarc

Anode power deposition is a dominant power loss mechanism for arcjets and magnetoplasmadynamic (MPD) thrusters. In this study, a free burning arc experiment was operated at pressures and current densities similar to those in arcjets and MPD thrusters in an attempt to identify the physics controlling this loss mechanism. Use of a free burning arc allowed for the isolation of independent variables controlling anode power deposition and provided a convenient and flexible way to cover a broad range of currents, anode surface pressures, and applied magnetic field strengths and orientations using an argon gas. Test results showed that anode power deposition decreased with increasing anode surface pressure up to 6.7 Pa and then became insensitive to pressure. Anode power increased with increasing arc current, while the electron number density near the anode surface increased linearly. Anode power also increased with increasing applied magnetic field strength due to an increasing anode fall voltage. Applied magnetic field orientation had an effect only at high currents and low anode surface pressures, where anode power decreased when applied-field lines intercepted the anode surface. The results demonstrated that anode power deposition was dominated by the kinetic energy of the current-carrying electrons acquired over the anode fall region. Furthermore, the results showed that anode power deposition can be reduced by operating at increased anode pressures, reduced arc currents, anode current densities, and applied magnetic field strengths, and with magnetic field lines intercepting the anode     

高功率微波沿面闪络击穿机制粒子模拟

针对高功率微波介质沿面闪络击穿物理过程,首先建立了理论模型,包括:动力学方程、粒子模拟算法、二次电子发射, 以及电子与气体分子蒙特卡罗碰撞模型、电子碰撞介质表面退吸附气体分子机制;其次,基于理论模型,编制了1D3V PIC-MCC程序,分别针对真空二次电子倍增、高气压体电离击穿和低气压面电离击穿过程,运用该程序仔细研究了电子和离子随时间演化关系、电子运动轨迹、电子及离子密度分布、空间电荷场时空分布、电子平均能量、碰撞电子平均能量、碰撞电子数目随时间演化关系、电子能量分布函数、平均二次电子发射率以及能量转换关系。研究结果表明:真空二次电子倍增引发的介质表面沉积功率只能达到入射微波功率1%左右的水平,不足以击穿;气体碰撞电离主导的高气压体电离击穿,是由低能电子（eV量级）数目指数增长到一定程度导致的,形成位置远离介质表面,形成时间为s量级;低气压下的介质沿面闪络击穿,是在二次电子倍增和气体碰撞电离共同作用下,由于数目持续增长的高能电子（keV量级）碰撞介质沿面导致沉积功率激增而引发的,形成位置贴近介质沿面,形成时间在ns量级。     

Microstructure and surface morphology of YSZ thin films deposited by e-beam technique

In present study yttrium-stabilized zirconia (YSZ) thin films were deposited on optical quartz (amorphous SiO₂), porous Ni-YSZ and crystalline Alloy 600 (Fe-Ni-Cr) substrates using e-beam deposition technique and controlling technological parameters: substrate temperature and electron gun power which influence thin-film deposition mechanism. X-ray diffraction, scanning electron microscopy (SEM), and atomic force microscopy (AFM) were used to investigate how thin-film structure and surface morphology depend on these parameters. It was found that the crystallite size, roughness and growth mechanism of YSZ thin films are influenced by electron gun power. To clarify the experimental results, YSZ thin-film formation as well evolution of surface roughness at its initial growing stages were analyzed. The evolution of surface roughness could be explained by the processes of surface mobility of adatoms and coalescence of islands. The analysis of these experimental results explain that surface roughness dependence on substrate temperature and electron gun power non-monotonous which could result from diffusivity of adatoms and the amount of atomic clusters in the gas stream of evaporated material.     

Transmission properties of all-silica fibres for high-power Nd:YAG lasers

The transmission properties of two different types of all-silica fibres, step index and graded-index fibres, are investigated using a multimode high-power cw Nd:YAG rod laser. The reflections from the fibre surface back into the laser cavity affect the laser power and the beam parameters, waist diameter and divergence. A set-up for simultaneously measuring these values in front of and behind a fibre is presented. The maximum laser power transmitted by fibres is dependent upon the beam parameters, the fibre design and the surface conditions. An upper limit for the maximum divergence which can be coupled into a fibre with a certain numerical aperture without loss is given. The beam parameters behind the fibre, related to the input parameters, are presented.     

Perturbation theory results for the diffuse scattering of light from two-dimensional randomly rough metal surfaces

Using the unitarity and reciprocity preserving formulation of Brown et al a perturbation treatment, correct to fourth order in the surface profile function, is given for the scattering of electromagnetic waves from a weakly rough, two-dimensional, random metal surface. In this formulation the boundary conditions on the electromagnetic fields are satisfied using the extinction theorem in conjunction with the Rayleigh hypothesis and the vector equivalent of the Kirchhoff integral. The theory is applied to, and results are presented for, several different types of rough surfaces which are characterized by power spectra that are extensions to two-dimensional random surfaces of the power spectrum of some one-dimensional random surfaces recently fabricated by West and O'Donnell. These surfaces, which can be realized experimentally, favor coherent, interferent, multiple scattering of electromagnetic waves via surface plasmon polaritons in intermediate states, and clearly exhibit enhanced backscattering caused by the surface plasmon polariton mechanism. Theoretical results are presented for silver surfaces at optical wavelengths.     

用小功率He-Ne激光器测量Ga1-xAlxAs外延片表面组份的均匀性

本文描述了一种简便可靠的分析Ga1-xAlxAs外延片表面组份均匀性的光学方法.在300K下,用小功率He-Ne激光器作光源,对x<0.39的n型和p型外延层进行了光致发光测量.依据光谱峰值获得表面的x值与扫描电镜所得结果相符.通过激发表面不同点处测得的光致发光光谱的位移,可以迅速而直观地分析出x值分布的均匀性.     

无工质微波推力器推力测量实验

基于经典的电磁学理论, 本文建立了一套新概念空间推进装置-----无工质微波推力器系统, 这套装置可以直接把微波辐射能转换为推力而不需要任何推进介质. 与传统的空间推进装置不同, 该系统可以避免携带庞大的推进剂储箱并消除羽流对航天飞行器的污染. 该系统由集成在一起的圆台微波谐振腔、 微波源和负载组成, 其中微波源产生的微波辐射能被输入到圆台微波谐振腔内并形成纯驻波与电磁压强梯度, 从而沿圆台微波谐振腔轴线方向形成净推力. 本文根据随遇平衡原理, 通过克服推力器本身的自重和刚性阻力, 成功地测量出无工质微波推力器产生的净推力. 结果表明: 基于经典电磁学理论建立的无工质微波推进系统可以产生净推力; 当微波源输出2.45 GHz, 80---2500 W的微波功率时, 推力器产生的推力分布在70---720 mN范围内, 测量总误差小于12%.