Broad spectral photonic crystal fiber surface enhanced Raman scattering probe

A broad spectral surface enhanced Raman scattering sensor is developed using the solid core holey photonic crystal fiber with silver nanoparticles cluster. This SERS probe offers an operational excitation wavelength range overlaying visible light and near infrared light. The PCF SERS sensing is demonstrated in the detection of the 4-Mercaptobenzoic acid (10⁻⁶ M) solution with 514.5 and 785 nm excitation. In this structure of PCF sensor, the related analysis shows that leakage modes also make an important contribution in the SERS activity not only by the evanescent field way.     

Fiber‐optic SERS sensor with optimized geometry: testing and optimization

A unique, geometry‐optimized, surface‐enhanced Raman scattering (SERS) fiber‐optic sensor has been recently developed and built. Though this class of sensors can be very useful in many applications, their use is greatly hindered by the fact that their reusability can hardly be achieved because of the irreversible adsorption of the analyte molecules on the SERS‐active substrate. Different substrates have been tested on our sensor with the purpose of increasing its reusability by means of cleaning procedures or good reproducibility in manufacturing the sensor, keeping, however, the same enhancement. We show that a partial reusability of the sensor is possible using SERS‐active substrates prepared by a standard process of immobilization of silver nanoparticles with 3‐aminopropyltrimethoxysilane. We also show that a fairly good reproducibility can be achieved with a low‐cost substrate realized in a short time by depositing a layer of polyvinyl alcohol (PVA) containing silver nanoparticles on the etched fiber tip. We prove as well that measurements are possible even with nanoparticles dispersed in the analyte solution instead of using a substrate directly made on the sensor tip. Finally, we have successfully tested our sensor with some molecules cited in EFSA (European Food Safety Authority) and FDA (Food and Drug Administration) reports as molecules for which new detection methods are necessary. Copyright © 2009 John Wiley & Sons, Ltd.     

AAO模板法制备CdS纳米微粒的SERS光谱研究

在自制的孔径约15nm多孔氧化铝模板上沉积银纳米粒子,然后用电化学方法在此衬底上沉积CdS纳米微粒。研究了CdS纳米阵列在457.5nm波长激光激发下的表面增强拉曼散射(SERS)性质。实验结果显示CdS的SERS信号有三个振动模式,分别对应1LO、2LO和3LO纵光学声子模,它们的强度随着作为SERS衬底的银纳米粒子高度的增加而增强,当银纳米粒子的长/径比(长度与直径的比值)达到4时,这种增强趋近饱和。最后对CdS纳米微粒光学声子模的增强机理进行了分析和讨论。     

Effects of solid substrate on the SERS‐based immunoassay: a comparative study

A comparative study of the solid substrates used in surface‐enhanced Raman scattering (SERS) based immunoassay is made in this paper. Five different substrates were prepared and divided into two groups with and without SERS activity. They are (1) a poly‐L ‐lysine slide, (2) a glutaraldehyde (GA)‐aminosilane slide, (3) a substrate assembled with silver nanoparticles, (4) a substrate assembled with silver nanoparticles and functionalized with GA–aminosilane and (5) a substrate assembled with gold nanoparticles, of which the first two are substrates are without SERS activity and the latter three are with SERS activity because of the existence of the metallic nanoparticles. The SERS experimental results show that the immunoassay performed on an SERS‐active substrate is more effective than that employing the inactive substrate. Among the inactive substrates, the GA–aminosilane slide with a better ability for antibody immobilization leads to a more sensitive immunoassay than the poly‐L ‐lysine slide. Moreover, for SERS‐based immunoassay, the substrate with assembled silver nanoparticles has an advantage of higher SERS enhancement capacity over the substrate assembled with gold nanoparticles. This work indicates that SERS‐active substrates play important and positive roles in sensitive SERS‐based immunoassay. Copyright © 2010 John Wiley & Sons, Ltd.     

Fabrication and characterization of a granular film consisting of size-selected silver nanoparticles: application to a SERS substrate

Uniform-sized silver nanoparticles with average diameter of 13.7 nm have been prepared in the gas-phase by combining a pulsed laser ablation method with a low pressure-differential mobility analyzer (LP-DMA). By depositing the silver nanoparticles onto a silicon substrate, a granular film consisting of size-selected silver nanoparticles has been fabricated and its morphology and electronic properties have been examined using transmission electron microscopy (TEM) and UV-visible absorption spectroscopy. This granular silver film serves as a highly active substrate for surface-enhanced Raman scattering (SERS).     

银和去合金银-金纳米粒子的SERS活性研究

用乙二醇还原硝酸银,聚乙烯吡咯烷酮作表面活性剂合成了大量的银纳米颗粒。银纳米颗粒和HAuCl4发生置换反应后形成去合金银-金纳米粒子。以吡啶和SCN-作为探针分子研究了它们的SERS活性。结果表明,当探针分子吸附于银纳米颗粒和去合金银-金纳米粒子上时,探针分子的特征振动峰强度增强、频率发生位移。SERS可表征纳米粒子物理和化学性质的变化。     

Fabrication and characterization of SERS‐active silver clusters on glassy carbon

In this article, a novel technique for the fabrication of surface enhanced Raman scattering (SERS) active silver clusters on glassy carbon (GC) has been proposed. It was found that silver clusters could be formed on a layer of positively charged poly(diallyldimethylammonium) (PDDA) anchored to a carbon surface by 4‐aminobenzoic acid when a drop containing silver nanoparticles was deposited on it. The characteristics of the obtained silver clusters have been investigated by atomic force microscopy (AFM), SERS and an SERS‐based Raman mapping technique in the form of line scanning. The AFM image shows that the silver clusters consist of several silver nanoparticles and the size of the clusters is in the range 80–100 nm. The SERS spectra of different concentrations of rhodamine 6G (R6G) on the silver clusters were obtained and compared with those from a silver colloid. The apparent enhancement factor (AEF) was estimated to be as large as 3.1 × 10⁴ relative to silver colloid, which might have resulted from the presence of ‘hot‐spots’ at the silver clusters, providing a highly localized electromagnetic field for the large enhancement of the SERS spectra of R6G. The minimum electromagnetic enhancement factor (EEF) is estimated to be 5.4 × 10⁷ by comparison with the SERS spectra of R6G on the silver clusters and on the bare GC surface. SERS‐based Raman mapping technique in the form of line scanning further illustrates the good SERS activity and reproducibility on the silver clusters. Finally, 4‐mercaptopyridine (4‐Mpy) was chosen as an analyte and the lowest detected concentration was investigated by the SERS‐active silver clusters. A concentration of 1.6 × 10⁻¹⁰ M 4‐Mpy could be detected with the SERS‐active silver clusters, showing the great potential of the technique in practical applications of microanalysis with high sensitivity. Copyright © 2006 John Wiley & Sons, Ltd.     

Self‐assembled silver nanoparticle monolayer on glassy carbon: an approach to SERS substrate

In this paper, the fabrication of an active surface‐enhanced Raman scattering (SERS) substrate by self‐assembled silver nanoparticles on a monolayer of 4‐aminophenyl‐group‐modified glassy carbon (GC) is reported. Silver nanoparticles are attached to the substrate through the electrostatic force between the negatively charged silver nanoparticles and the positively charged 4‐aminophenyl groups on GC. The active SERS substrate has been characterized by means of tapping‐mode atomic force microscopy (AFM), indicating that large quantities of silver nanoparticles are uniformly coated on the substrate. Rhodamine 6G (R6G) and p‐aminothiophenol (p‐ATP) are used as the probe molecules for SERS, resulting in high sensitivity to the SERS response, with the detection limit reaching as low as 10⁻⁹ M . This approach is easily controlled and reproducible, and more importantly, can extend the range of usable substrates to carbon‐based materials for SERS with high sensitivity. Copyright © 2007 John Wiley & Sons, Ltd.     

785 nm激光诱导银纳米三角片聚集表面增强拉曼散射效应

为实现表面增强拉曼散射（SERS）光谱的强信号快速检测分析,报道了通过785 nm激光诱导银纳米三角片（AgNPRs）聚集的方法。采用配体辅助化学还原法制备了AgNPRs,其边长约为80 nm,表面等离子体吸收峰出现在约774 nm处,对785 nm光产生有效吸收。在785 nm光辐照下,AgNPRs逐渐聚集,对巯基苯甲酸的SERS信号逐渐增强,其源于AgNPRs吸收的光转化为热而引起的AgNPRs聚集。其增强因子高达10⁹。为快速获得强SERS信号,激发光功率需大于250 mW。     

巯基苯甲酸在电化学沉积的金/银薄膜表面的吸附行为

通过表面增强拉曼散射(SERS)技术和密度泛函理论(DFT)研究对巯基苯甲酸自组装在电化学沉积的金和银薄膜表面的吸附行为.结果表明电化学沉积的金和银薄膜是良好的SERS活性基底. 通过对巯基苯甲酸的SERS光谱分析和DFT理论计算,以及表面选择定则,得到了对巯基苯甲酸主要通过羧基自组装在电化学沉积银膜表面,并且苯环表面可能和银表面有一倾角,对巯基苯甲酸主要通过硫原子和金表面相互作用,并且苯环平面可能和金膜表面有一个倾角     

Large scale synthesis of pinhole‐free shell‐isolated nanoparticles (SHINs) using improved atomic layer deposition (ALD) method for practical applications

Shell‐isolated nanoparticle‐enhanced Raman spectroscopy (SHINERS) as a new member of Raman technique garnered great attention among scientific community. In this work, we used an improved experimental setup to float the bare silver nanoparticles in air with the help of extraneous airflow, and used atomic layer deposition (ALD) method to coat ultra‐thin inert shell without pinholes. Under optimal conditions, we successfully prepared three kinds of SHINERS NPs (Ag@Al₂O₃, Ag@SiO₂ and Ag@TiO₂) in large quantity without pinholes. The ultra‐thin inert shell maintains the SERS activity of silver nanoparticles for long period of time. Transmission electron microscopy (TEM) images confirm the uniform coating of shell material on silver nanoparticles. Finally, the as‐prepared SHINs have been applied to detect various samples to demonstrate the applications. The presented ALD method offers a unique way to coat ultrathin shell (1–10 nm) on metal nanoparticles in large quantity (1–10 g) for practical applications. Copyright © 2015 John Wiley & Sons, Ltd.     

Surface enhanced Raman scattering of molecules related to highly ordered gold cavities

We presented a controlled particles‐in‐cavity (PIC) pattern for surface‐enhanced Raman scattering (SERS) detection. The periodic gold cavity array was fabricated by electrodeposition using highly ordered polystyrene spheres as a template. The as‐prepared gold cavities can be used as a SERS active substrate with significant spectral enhancement and reproducibility, which was evaluated by SERS signals using 4‐mercaptobenzoic acid (4‐MBA) as probe molecules. The surface of these gold cavities was further functionalized with cetyltrimethylammonium bromide molecules, which may immobilize the 4‐MBA‐modified silver nanoparticles in the gold cavity to form a PIC structure via the electrostatic interaction. We have demonstrated that there exists a pH window for the immobilization of the nanoparticles inside cavities. Therefore, the silver nanoparticles can be selectively immobilized into the functionalized gold cavities under the optimized pH value of the media. Further enhancement of the Raman scattering of the labeled molecules can be achieved due to the interconnection between the silver nanoparticles and gold cavity. Copyright © 2013 John Wiley & Sons, Ltd.     

银纳米粒子的SERS效应和SEF效应在微流控芯片光学检测中的应用

银纳米离子的SERS技术和SEF技术的信号检测灵敏度非常高,可以用在微流控芯片的定量分析中。为了提高微流控芯片光学检测技术的检测精度,提出一种在微通道中添加银纳米粒子来增强SYBR GreenⅠ拉曼和荧光信号的方法,并对该方法的原理和增强效果进行了研究。首先,利用准分子激光器在PMMA基板上直写刻蚀出宽200 μm、深68 μm的微通道,接着将制备的银前体溶液加入微通道,通过加热制备出表面增强拉曼（SERS）和表面增强荧光（SEF）基板,接下来对添加银纳米粒子前后的拉曼和荧光信号分别进行对比,进一步研究了微通道中不同浓度银纳米粒子对SYBR GREEN I的拉曼和荧光信号增强效果。添加银纳米粒子后,表面增强拉曼（SERS）实验的增强因子为3.5×10³,添加银纳米粒子的样品的荧光信号强度与不含银纳米粒子样品的荧光信号强度相比,约增加了1倍。结果表明,在微通道中检测SYBR Green I时通过增加银纳米粒子显著地增强了拉曼和荧光信号,这种方法可以用在以SYBR GreenⅠ做染料的微流控芯片检测技术中。     

Piperidine adsorption on two different silver electrodes: A combined surface enhanced Raman spectroscopy and density functional theory study

The surface enhanced Raman scattering (SERS) spectra of piperidine in silver colloid solution, on roughened silver electrode and on roughened silver electrode modified with silver nanoparticles were studied, and the high-quality SERS spectra of piperidine on roughened silver electrode modified with silver nanoparticles were obtained for the first time. Surface selection rules derived from the EM enhancement model were employed to deduce piperidine orientations on the different surfaces. On the basis of this, two models of piperidine adsorbed on the surface of the silver nanoparticles were built, and DFT-B3PW91/LanL2dz was applied to calculate the Raman frequencies. It proves that, at higher potential values, the piperidine is perpendicularly standing on the roughened silver electrode surface though its lone-electron pair, but in silver colloid solution and on the silver nanoparticles modified silver electrode the piperidine molecular lies flat on the silver surface. In the meantime, the potential dependent SERS of piperidine on the modified electrode were studied.     

Laser-Induced Silver Nanoparticles Deposited on Optical Fiber Core for Surface-Enhanced Raman Scattering

We report on surface-enhanced Raman scattering （SERS） probes based on silver nanopaxtieles which axe deposited on the core of the distal end of standard single mode fibers, by means of the very simple, versatile, and lowcost laser-induced nanoparticle technique. The morphological features of the Ag nanoparticles vary according to the experimental conditions such as laser power, illumination time, and concentration of the reaction solution. The SERS activity of the probes is demonstrated with the detections of rhodamine 6G aqueous solutions. The detections are made from both ends of the probes, i.e., in direct detection mode from the end with nanoparticles and in remote detection mode from the distal end, respectively.     

Surface-enhanced Raman scattering active substrates by liquid flame spray deposited and inkjet printed silver nanoparticles

Surface-enhanced Raman scattering (SERS) active substrates were made via liquid flame spray deposition and inkjet printing of silver nanoparticles. Both processes are suitable for cost-effective fabrication of large-area SERS substrates. Crystal violet (CV) solutions were used as target molecules and in both samples the detection limit was approximately 10 nM. In addition, sintering temperature of the inkjet printed silver nanoparticles was found to have a large effect on the SERS activity with the higher curing temperature of 200 °C resulting in contamination layer on silver and cancelation of the SERS signal. This layer was characterized using an X-ray photoelectron spectroscopy (XPS).     

质子酸功能化离子液体中银纳米颗粒的制备及其光学性能研究

以质子酸功能化离子液体1-丁基-3-甲基咪唑磷酸二氢盐([Bmim]H₂PO₄)为反应介质和表面活性剂,采用简单的化学还原法制备了具有形状各向异性的块状银纳米颗粒。通过X射线衍射(XRD)、扫描电镜(SEM)、紫外-可见(UV-Vis)吸收光谱等一系列手段对其结构、形貌及光吸收特性进行了表征。结果表明,所制备的银纳米块具有立方结构,其平均横向尺寸约为30 nm,在硅片上自组装形成密堆积结构的多层膜。以1,2-二(4-吡啶基)乙烯(BPE)作为探针分子,研究所制备银纳米颗粒的表面增强拉曼散射(SERS)活性。结果表明所制的银纳米颗粒是较好的SERS基底,具有良好的增强效果,痕检能力及稳定性。对BPE分子的最低检测浓度可低至10-9mol·L-1,而且保存了90天后,其检测灵敏度没有显著的降低。     

Facile synthesis of gelatin‐protected silver nanoparticles for SERS applications

Gelatin‐protected silver nanoparticles have been synthesized by a one‐pot, green method for surface‐enhanced Raman scattering (SERS) applications using gelatin as the reducing and stabilizing agent. The gelatin protection on silver nanoparticle surface helps improve its stability greatly and water dispersibility, while retaining high SERS activity of silver nanoparticles. The gelatin‐protected silver nanoparticles showed SERS signals as low as 100 nM of the typical Raman reporter molecules, RuBPY and R6G and 10 μM of other molecules of interest, melamine and folic acid. Copyright © 2013 John Wiley & Sons, Ltd.     

Strategy for improved analysis of peptides by surface‐enhanced Raman spectroscopy (SERS) involving positively charged nanoparticles

A strategy for improved surface‐enhanced Raman spectroscopy (SERS) measurements that extends the variety of analytes accessible to SERS analysis is developed. The strategy involves inducing aggregation by mixing positively charged nanoparticles which form SERS‐active clusters when mixed with negatively charged silver nanoparticles fabricated using the Lee–Meisel process. To make positively charged nanoparticles, silver nanoparticles using the traditional Lee–Meisel process are fabricated and coated with a thin layer of silica and the silica modified with silane chemistry. Analytes with a significant amount of negative charge exhibit strong Raman bands when the strategy using these fabricated, positively charged nanoparticles for inducing cluster formation is used, enabling their detection and analysis. We envision the use of positively charged nanoparticles in cluster formation for expanding the range of analytes that can be detected using SERS and hence the range of applications SERS can play a role in. Copyright © 2008 John Wiley & Sons, Ltd.     

哌啶分子在两种不同银电极上吸附行为的实验和理论研究

分别在粗糙银电极和银纳米颗粒修饰银电极上得到了哌啶分子的表面增强拉曼（SERS）光谱。哌啶在银电极与银纳米颗粒修饰的银电极上的SERS谱有很大的区别,分析认为是由于哌啶在不同基底上的吸附方式不同所引起的,据此建立了哌啶吸附在银颗粒表面的两种模型,用DFT-B3PW91-lanl2dz方法计算了两种模型的拉曼频移,通过与实验结果比较说明了哌啶分子主要通过N原子的孤对电子竖直吸附在粗糙银电极表面,而在银纳米颗粒修饰的银电极上则以平行吸附方式为主。