Annealing effects on the properties of Ga2O3 thin films grown on sapphire by the metal organic chemical vapor deposition

We have prepared the gallium oxide (Ga₂O₃) thin films on sapphire substrates by the metal organic chemical vapor deposition (MOCVD) technique. We have compared the two films with and without the thermal annealing by using the X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and the photoluminescence (PL) spectra. Postdeposition annealing of amorphous Ga₂O₃ films was found to increase the degree of crystallization and the surface roughness. The PL emission intensities of bands in the blue–green and the ultraviolet regions increased by the thermal annealing.     

Characterization of hetero-interfaces between group III nitrides formed by PLD and various substrates

We have grown group III nitride epitaxial films on various substrates by pulsed laser deposition and investigated structural properties of the surfaces and the hetero-interfaces using grazing incidence angle X-ray reflectivity (GIXR) and atomic force microscopy (AFM). It has been found that hetero-interfaces between PLD AlN and conventional substrates such as Al₂O₃ and Si are quite abrupt (about 0.5 nm) probably due to a less reactive growth ambience. However, we observed a thin interfacial layer (less than 10 nm) at the hetero-interface between AlN and (Mn,Zn)Fe₂O₄. The surface roughness of AlN is mainly determined by the extent of the lattice mismatch. It has been also found that the roughness at the hetero-interface between GaN and AlN formed by PLD coincides with the surface roughness of the AlN layer.     

Synthesis and optical characterization of c-axis oriented GaN thin films on amorphous quartz glass via sol–gel process

c-Axis oriented GaN nanocrystalline thin films were fabricated by nitridation of three different thin films of -GaO(OH), -Ga₂O₃ or β-Ga₂O₃ obtained by sol–gel technique on amorphous quartz glass substrates. All these GaN thin films showed near band edge emission at 390 nm and yellow luminescence at 570 nm. The crystalline nature and c-axis orientation as well as luminescence properties of the GaN thin films increased by several times by using a buffer layer of GaN on the substrate.     

等离子增强原子层沉积低温生长GaN薄膜

采用等离子增强原子层沉积技术在低温下于单晶硅衬底上成功生长了Ga N多晶薄膜,利用椭圆偏振仪、低角度掠入射X射线衍射仪、X射线光电子能谱仪对薄膜样品的生长速率、晶体结构及薄膜成分进行了表征和分析.结果表明,等离子增强原子层沉积技术生长Ga N的温度窗口为210—270?C,薄膜在较高生长温度下呈多晶态,在较低温度下呈非晶态;薄膜中N元素与大部分Ga元素结合成N—Ga键生成Ga N,有少量的Ga元素以Ga—O键存在,多晶Ga N薄膜含有少量非晶态Ga_2O_3.     

常压MOCVD生长Ga2O3薄膜及其分析

以去离子水(H₂O)和三甲基镓(TMGa)为源材料,用常压MOCVD方法在蓝宝石(0001)面上生长出β-Ga₂O₃薄膜.用原子力显微镜(AFM)、X射线衍射(XRD)以及二次离子质谱(SIMS)实验表征Ga₂O₃外延膜的质量.在X射线衍射谱中有一个强的Ga₂O₃(102)面衍射峰,其半峰全宽(FWHM)为0.25°,表明该Ga₂O₃外延膜是(102)择优取向.在二次离子质谱中除了C、H、O和Ga原子外,没有观测到其他原子.     

The effect of hydrogen on copper nitride thin films deposited by magnetron sputtering

Copper nitride thin films were deposited on Si (1 0 0) wafers by reactive magnetron sputtering at various H₂/N₂ ratios. X-ray diffraction measurements show that the films are composed of Cu₃N crystallites with anti-ReO₃ structure and exhibit preferred orientation of [1 0 0] direction. Although the relative composition of the films has obviously changes with the H₂/N₂ ratios, the orientations of the films keep almost no changes. However, the grain size, lattice parameter and composition of the films are strongly dependent on the H₂/N₂ ratios. The copper nitride films prepared at 10% H₂/N₂ ratios show poor stability and large weight gain compared to the copper nitride films prepared at 0% H₂/N₂ ratios.     

Enhanced luminescence from transparent Ni-doped MgO–Al2O3–SiO2 glass ceramics by Ga2O3 addition

Transparent Ni²⁺-doped MgO–Al₂O₃–SiO₂ glass ceramics without and with Ga₂O₃ were synthetized. The precipitation of spinel nanocrystals, which was identified as solid solutions in the glass ceramics, could be favored by Ga₂O₃ addition and their sizes were about 7.6 nm in diameter. The luminescent intensity of the Ni²⁺-doped glass ceramics was largely enhanced by Ga₂O₃ addition which could mainly be caused by increasing of Ni²⁺ in the octahedral sites and the reduction of the mean frequency of phonon density of states in the spinel nanocrystals of solid solutions. The full width at half maximum (FWHM) of emissions for the glass ceramics with different Ga₂O₃ content was all more than 200 nm. The emission lifetime increased with the Ga₂O₃ content and the longest lifetime is about 250 μs. The Ni²⁺-doped transparent glass ceramics with Ga₂O₃ addition have potential application as broadband optical amplifier and laser materials.     

Characterization of high-k gate dielectric/silicon interfaces

We have shown that, for thermally evaporated Ta₂O₅ or ZrO₂ thin films on Si(1 0 0), O₂ annealing at 300–500 °C causes the formation of an interfacial silicon oxide layer as thin as 1–2 nm which can be interpreted in terms of their high permeability to oxygen. And we have demonstrated how useful the energy loss spectra of photoexcited electrons from core levels such as O 1s are to measure the energy bandgaps of very thin insulators. With the combination of measured bandgaps and valence band lineups determined for X-ray photoelectron spectroscopy valence band spectra, we have determined the energy band alignments of Ta₂O₅ and ZrO₂ with Si(1 0 0) before and after the O₂ annealing at 500 °C. In addition, we have demonstrated that total photoelectron yield spectroscopy provides us direct information to quantify the energy distributions of both the defect states in the high-k dielectrics and the dielectric/Si(1 0 0) interface states over nearly entire Si bandgap.     

In situ X-ray photoelectron spectroscopy study of the oxidation of CuGaSe2

The thermal and native oxidation of CuGaSe₂ thin films was studied by in situ X-ray photoelectron spectroscopy (XPS). The special design of the XPS chamber allowed to measure XP-spectra under oxidizing gas atmospheres at pressures of up to 5 mbar (in situ) or in ultra high vacuum (UHV). During thermal oxidation, the formation of predominantly Ga₂O₃ and some amount of SeO₂ were observed, but no copper oxides could be detected in the near surface region of the thin films. The same oxides were found after native oxidation in air under ambient conditions. Only after long term native oxidation for longer than 4 months Cu(OH)₂ was detected. An additional sodium oxide compound formed at the thin film surface, Na_xO and Na₂CO₃ after thermal and native oxidation, respectively. The amount of these sodium oxide compounds depends on the Na content on the as prepared surface. The formation of SeO₂ under humid conditions at 100 °C was found to depend on the surface composition of the thin film.     

Atomic layer deposition of Cr2O3 thin films: Effect of crystallization on growth and properties

Atomic layer deposition of Cr₂O₃ thin films from CrO₂Cl₂ and CH₃OH on amorphous SiO₂ and crystalline Si(1 0 0) and -Al₂O₃() substrates was investigated, and properties of the films were ascertained. Self-limited growth with a rate of 0.05–0.1 nm/cycle was obtained at substrate temperatures of 330–420 °C. In this temperature range epitaxial eskolaite was formed on the -Al₂O₃() substrates. The predominant crystallographic orientation in the epitaxial films depended, however, on the growth temperature and film thickness. Sufficiently thick films grown on the SiO₂ and Si(1 0 0) substrates contained also the eskolaite phase, but thinner films deposited at 330–375 °C on these substrates were amorphous. The growth rate data of films with different phase composition allowed a conclusion that the crystalline phase grew markedly faster than the amorphous phase did. The amorphous, polycrystalline and epitaxial films had densities of 4.9, 5.1 and 5.1–5.3 g/cm³, respectively.     

氧化镓薄膜的制备及其日盲紫外探测性能研究

采用射频磁控溅射方法在蓝宝石单晶衬底上沉积氧化镓(Ga2O3)薄膜,并通过光刻剥离工艺(Lift-off)制备了金属-半导体-金属结构的Ga2O3日盲紫外探测器。对不同温度下沉积的Ga2O3薄膜分析表明,在800℃下获得的薄膜结晶质量最好,薄膜的导电性则随着沉积温度的上升先增大后减小。在800℃制备的β-Ga2O3薄膜的可见光透光率大于90%,光学吸收边在255 nm附近。在10 V偏压下,探测器的暗电流约为1n A,光电流达800 n A,对紫外光响应迅速。器件的响应度达到0.3 A/W,260 nm波长处的响应度是290 nm波长对应响应度的40倍,可实现日盲紫外波段的探测。     

Structural and electrical properties of crystalline (1−x)Ta2O5−xTiO2 thin films fabricated by metalorganic decomposition

Polycrystalline (1−x)Ta₂O₅−xTiO₂ thin films were formed on Si by metalorganic decomposition (MOD) and annealed at various temperatures. As-deposited films were in the amorphous state and were completely transformed to crystalline after annealing above 600 °C. During crystallization, a thin interfacial SiO₂ layer was formed at the (1−x)Ta₂O₅−xTiO₂/Si interface. Thin films with 0.92Ta₂O₅–0.08TiO₂ composition exhibited superior insulating properties. The measured dielectric constant and dissipation factor at 1 MHz were 9 and 0.015, respectively, for films annealed at 900 °C. The interface trap density was 2.5×10¹¹ cm⁻² eV⁻¹, and flatband voltage was −0.38 V. A charge storage density of 22.8 fC/μm² was obtained at an applied electric field of 3 MV/cm. The leakage current density was lower than 4×10⁻⁹ A/cm² up to an applied electric field of 6 MV/cm.     

Effect of annealing temperature on the structural and electrical properties of SrBi2Ta2O9 thin films for memory-based applications

Ferroelectric SrBi₂Ta₂O₉ (SBT) thin films were grown on p-type (1 0 0) Si substrates by radio frequency sputtering technique. The crystallinity of the films was studied using grazing incidence X-ray diffraction pattern. The spectra showed the films were polycrystalline with dominant orientation along (1 1 5) plane. The surface morphology was investigated by atomic force microscope. The chemical composition was studied by Rutherford back-scattering, which yielded a near stoichiometric composition of SBT. The capacitance–voltage characteristics of Al/SBT/Si capacitors measured at 100 kHz showed a hysteresis nature with a clockwise rotation and the memory window of the hysteresis loop was 0.88 V with the gate voltage ±5 V. The interface trap density was calculated by using Hills method at room temperature and a value in the order of 10¹¹–10¹² eV⁻¹ cm⁻² was found depending on the crystallization temperature at midgap region.     

X-ray diffraction studies of epitaxy in orthorhombic- DyMnO3/Er1Ba2Cu3O7-δ thin film heterostructures on LaAlO3 (100) substrates

The heteroepitaxy in DyMnO₃/Er₁Ba₂Cu₃O_7-δ bilayer thin films on LaAlO₃ (100) substates was characterized by four-circle X-ray diffractometry. The Er₁Ba₂Cu₃O_7-δ thin films on LaAlO₃ (100) substrates were prepared by molecular-beam deposition (MBD) and post-growth annealing in wet and dry O₂ at 880°C, whereas the DyMnO₃ thin films on the Er₁Ba₂Cu₃O_7-δ/LaAlO₃ (100) heterostructure were deposited by MBD and post-growth annealing in dry O₂ at 750°C. The conventional X-ray diffraction (XRD) patterns as well as pole figures (φ-scans) for specific (hkl) reflections were acquired. The Er₁Ba₂Cu₃O_7-δ thin film in the DyMnO₃/Er₁Ba₂Cu₃O_7-δ/LaAlO₃ (100) heterostructure showed [001] oriented epitaxial growth, as expected. The DyMnO₃ thin film on the Er₁Ba₂Cu₃O_7-δ epilayer in the heterostructure grew with (110) epitaxy in its metastable orthorhombic phase (lattice constants: a_o=5.272 Å, b_o=5.795 Å and c_o=7.38 Å). The heteroepitaxial relationships at the orthorhombic-DyMnO O₃ (110) /Er₁Ba₂Cu₃O_7-δ (001) interface was determined as the following: DyMnO₃ (110) Er₁Ba₂Cu₃O_7-δ (001), DyMnO₃ [1 0] ¶r; Er₁Ba₂Cu₃O_7-δ[100] or Er₁Ba₂Cu₃O_7-δ[010], and DyMnO₃ [001] ¶r; Er₁Ba₂Cu₃O _7-δ[010] or Er₁Ba₂Cu₃O_7-δ [100].     

Deposition and characterization of carbon nitride films from hexamethylenetetramine/N2 by microwave plasma-enhanced chemical vapor deposition

Carbon nitride thin films were deposited on Si(1 0 0) substrate by microwave plasma-enhanced chemical vapor deposition (PECVD). Hexamethylenetetramine (HMTA) was used as carbon and nitrogen source while N₂ gas was used as both nitrogen source and carrier gas. The sp³-bonded C---N structure in HMTA was considered significantly in the precursor selection. X-ray diffraction analysis indicated that the film was a mixture of crystalline - and β-C₃N₄ as well as graphitic-C₃N₄ and β-Si₃N₄ which were not easily distinguished. Raman spectroscopy also suggested the existence of - and β-C₃N₄ in the films. X-ray photoelectron spectroscopy study indicated the presence of sp²- and sp³-bonded C---N structures in the films while sp³C---N bonding structure predominated to the sp² C---N bonding structure in the bulk composition of the films. N was also found to be bound to Si atoms in the films. The product was, therefore, described as CN_x:Si, where x depends on the film depth, with some evidences of crystalline C₃N₄ formation.     

Elemental steps in the growth of thin β-Ga2O3 films on CoGa(1 0 0)

The oxidation of CoGa(1 0 0) at 700 K was studied by means of high resolution electron energy loss spectroscopy (EELS), scanning tunneling microscopy, low energy electron diffraction and Auger electron spectroscopy (AES). At 700 K, thin well-ordered β-Ga₂O₃ films grow on CoGa(1 0 0). The EEL spectrum of the Ga-oxide films exhibit Fuchs–Kliewer phonons at 305, 455, 645, and 785 cm⁻¹. For low oxygen exposure (<0.2 L), the growth of oxide-islands starts at step edges and on defects. The oxide films have the shape of long, rectangular islands and are oriented in the [1 0 0] and [0 1 0] directions of the substrate. For higher oxygen exposure, islands of β-Ga₂O₃ are found also on the terraces. After an exposure of 200 L O₂ at 700 K, the CoGa(1 0 0) surface is homogeneously covered with a thin film of β-Ga₂O₃.     

Thickness dependence of microstructures in La0.9Sr0.1MnO3 thin films grown on exact-cut and miscut SrTiO3 substrates

The thickness dependence of microstructures of La_0.9Sr_0.1MnO₃ (LSMO) thin films grown on exact-cut and miscut SrTiO₃ (STO) substrates, respectively, was investigated by high-angle X-ray diffraction (HXRD), X-ray small-angle reflection (XSAR), X-ray reciprocal space mapping and atomic force microscopy (AFM). Results show that the LSMO films are in pseudocubic structure and are highly epitaxial [0 0 1]-oriented growth on the (0 0 1) STO substrates. The crystalline quality of the LSMO film is improved with thickness. The epitaxial relationship between the LSMO films and the STO substrates is [0 0 1]_LSMO[0 0 1]_EXACT-STO, and the LSMO films have a slight mosaic structure along the q_x direction for the samples grown on the exact-cut STO substrates. However, an oriented angle of about 0.24° exists between [0 0 1]_LSMO and [0 0 1]_MISCUT-STO, and the LSMO films have a mosaic structure along the q_z direction for that grown on the miscut STO substrates. The mosaic structure of both groups of the samples tends to reduce with thickness. The diffraction intensity of the (0 0 4) peaks increases with thickness of the LSMO film. The XSAR and AFM observations show that for both groups, the interface is sharp and the surface is rather smooth. The mechanism was discussed briefly.     

Direct growth of graphene on gallium nitride using C2H2 as carbon source

Growing graphene on gallium nitride (GaN) at temperatures greater than 900°C is a challenge that must be overcome to obtain high quality of GaN epi-layers. We successfully met this challenge using C₂H₂ as the carbon source. We demonstrated that graphene can be grown both on copper and directly on GaN epi-layers. The Raman spectra indicated that the graphene films were about 4–5 layers thick. Meanwhile, the effects of the growth temperature on the growth of the graphene films were systematically studied, and 830°C was found to be the optimum growth temperature. We successfully grew high-quality graphene films directly on gallium nitride.     

Structural and electrical characterisation of La0.5Ca0.5MnO3 thin films grown by pulsed laser deposition

Thin films of perovskite manganite, with nominal composition La_0.5Ca_0.5MnO₃, have been prepared by pulsed laser deposition on (1 0 0) SrTiO₃, (1 0 0) LaAlO₃, (1 0 0) Si and YSZ/CeO₂-buffered (1 0 0) Si substrates. Structural and electrical characterisation was performed on the films. The magneto-transport properties of all the thin films depart from the bulk behaviour. The LCMO film grown on buffered Si shows an insulator–metallic transition around 130–150 K while the one deposited directly on Si displayed a similar behaviour under a melting field of 1 T. However, that transition is absent in the films grown on LAO and STO. We suggest that appropriate stress values induced by the substrate favour the formation of metallic percolative paths.     

Superconducting Nd1.85Ce0.15CuO4 films grown by the pulsed electron deposition technique

Nd_1.85Ce_0.15CuO_4−δ superconducting thin films were prepared on (1 0 0) SrTiO₃ substrates by pulsed electron deposition technique without reducing atmosphere. Oxygen content is finely controlled by high temperature vacuum annealing, and optimal superconductivity has been obtained. The deposition conditions of the film are discussed in details. Higher deposition temperature and lower gas pressure result in the loss of copper and the appearance of the foreign phase Ce_0.5Nd_0.5O_1.75. High quality Nd_1.85Ce_0.15CuO_4−δ epitaxial films are deposited at 840–870 °C in the mixed gas with a ratio of O₂:Ar = 1:3.