Sr0.6Ba0.2Ca0.2Al2O4 ∶Eu,Dy的制备与长余辉发光性能研究

采用高温固相法制备了Ca,Ba共掺的Sr_0.6Ba_0.2Ca_0.2Al₂O₄ ∶Eu²⁺_0.01, Dy³⁺_0.02和单掺Ba的Sr_0.6Ba_0.4Al₂O₄ ∶Eu²⁺_0.01, 关键词： 长余辉 铝酸锶 稀土掺杂 陷阱能级     

蓝色长余辉材料Sr2MgSi2O7：Eu2+,Dy3+及其基质的VUV-UV激发特性

Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺是一种有效的蓝色长余辉材料,采用高温固相法合成了Sr₂MgSi₂O₇,Sr₂MgSi₂O₇:Dy³⁺,Sr₂MgSi₂O₇:Eu²⁺及Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺,利用同步辐射研究了它们的VUV-UV激发特性.在真空紫外光激发下,在基质中发现了稍弱的位于385nm的发射带,在双掺杂的样品中,除了Eu²⁺的4f5d→4f发射带(465nm)外,还观察到了575nm处的发射峰;通过和Dy³⁺单掺杂样品的发射谱比较,发现它是来自于Dy³⁺的4f-4f(⁴F_9/2→6H_13/2)跃迁.在它们的激发谱上可以看出Dy³⁺与基质发射的有效激发均处于真空紫外区,在近紫外及可见区激发下未见到它们发光.另外在Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺中观察到Dy³⁺的发射也说明了Dy³⁺在该类长余辉材料中不仅作为陷阱用来延长余辉,而且也以发光中心形式存在于基质中.     

SrAl2O4∶Eu2+,Dy3+长余辉发光材料的喷雾热解制备及其表征

采用喷雾热解两段法制备了SrAl₂O₄∶Eu²⁺ ,Dy³⁺长余辉发光材料,并利用XRD、SEM、荧光长余辉亮度测试等方法分析了不同制备工艺条件下SrAl₂O₄∶Eu²⁺ ,Dy³⁺发光材料的结构、形貌以及发光性能的变化。结果表明:采用喷雾热解两段法可制备出球形SrAl₂O₄∶Eu²⁺ ,Dy³⁺长余辉发光材料,SrAl₂O₄∶Eu²⁺ ,Dy³⁺的晶体结构与α-SrAl₂O₄磷石英晶体结构相同。热解温度、还原温度、添加剂对产物的形貌、粒度分布、发光性能有较大影响。较之高温固相法,喷雾热解法制备的SrAl₂O₄∶Eu²⁺ ,Dy³⁺具有发光性能好、形貌好、粒度分布窄等优点。     

共沉淀法制备Y2O2S：Eu3+,Mg2+,Ti4+红色长余辉材料

用共沉淀法制备了Y₂O₂S:Eu³⁺,Mg²⁺,Ti⁴⁺红色长余辉材料。测量了材料的电子显微形貌、晶体结构和发射光谱。通过与固相法制备的Y₂O₂S:Eu³⁺,Mg²⁺,Ti⁴⁺长余辉材料比较,发现两种方法都可以制备粒度基本相同的纯相Y₂O₂S基质晶体,但共沉淀法样品的颗粒结构更松散。研究了Eu³⁺浓度对两种方法制备样品的谱线发射强度的影响,通过比较共沉淀法和高温固相法制备的样品中Eu³⁺的⁵D₁→⁷F₃较高能级跃迁的587.6nm谱线强度随Eu³⁺浓度的变化,发现共沉淀法更有利于Eu³⁺均匀进入Y₂O₂S基质晶格而形成有效的发光中心。     

激发波长和Eu2+的掺杂量对Sr4Al14O25 ∶ Eu2+ , Dy3+发光性能的影响

采用溶胶-凝胶法在低温、还原气氛下制备了长余辉发光材料Sr₄Al₁₄O₂₅ ∶ Eu²⁺,Dy³⁺。用X射线粉末晶衍射对其进行了物相鉴定,表明在1 200 ℃已经得到纯相的Sr₄Al₁₄O₂₅ 产物。研究了铕和锶的比值、激发光波长对所制备的Sr₄Al₁₄O₂₅ ∶ Eu²⁺, Dy³⁺发光性能的影响并对其影响机理进行了探讨。样品的发光性能测试结果表明:采用溶胶-凝胶法制备长余辉发光材料Sr₄Al₁₄O₂₅ ∶ Eu²⁺, Dy³⁺,其灼烧温度比高温固相法灼烧温度低;激发光谱向长波方向延伸时,在488 nm处发射峰增强,在410 nm处发射峰减弱;在一定范围内发光强度随着Eu²⁺量的增加而增强,Eu²⁺的最佳掺杂量为0.007, Eu²⁺的掺杂量超过0.007时会发生浓度猝灭。     

长余辉材料Sr2MgSi2O7：Eu2+,Dy3+中稀土离子的发光特性

利用同步辐射光源(德国HASYLAB实验室的SUPERLUMI实验站)和真空紫外激光(157.6nm)对新型蓝光发射长余辉材料Sr₂MgSi₂O₇:Eu²⁺(0.2%),Dy³⁺(8%)进行了光谱研究。在170nm同步辐射光源激发下,观察到对应Eu²⁺:5d-4f跃迁的477nm发射带和对应Dy³⁺:4f-4f跃迁的两组线谱发射,其中只有来自Eu²⁺的5d-4f发射对长余辉光谱有贡献。在157.6nm激光激发下,除了上述发射外,还明显观察到对应Eu³⁺的红色线谱(590,614,626nm)。结合这些光谱特性,对Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺中稀土离子的发光特性以及长余辉发光机理进行了讨论,并提出了Eu²⁺充当空穴陷阱的可能性。     

氧空位对Eu2+, Dy3+掺杂的Ca5MgSi3O12发光及余辉性能的影响

利用高温固相法合成了稀土离子Eu²⁺, Dy³⁺掺杂的Ca₅MgSi₃O₁₂长余辉发光材料. 利用光谱学证明了在材料内部存在与氧空位有关的缺陷发光. 通过对比不同条件下合成样品的发光及余辉性能, 发现氧空位对材料的发光及余辉均起到促进作用. 同时发现氧空位发光可以向发光中心传递能量. 利用热释光曲线系统的分析了氧空位对余辉性能的影响. Ca₅MgSi₃O₁₂:Eu²⁺,Dy³⁺是一种潜在的长余辉发光材料. 关键词： 长余辉 氧空位 能量传递 热释光     

Mg5SnB2O10:Eu3+,Bi3+—一种用于发光二极管的红色荧光粉的制备及其发光性能的研究

采用高温固相法成功合成了单一相的Eu³⁺,Bi³⁺共掺的Mg₅SnB₂O₁₀红色荧光粉,并通过X射线衍射、漫反射光谱、光致发光光谱等手段对该体系的结构及其发光特性进行了测试和研究.激发光谱表明,该荧光粉在393 nm呈现Eu³⁺的⁷Fo—⁵L₆特征激发,可以与用于发光二极管的近紫外芯片很好地匹配.在393 nm激发下,其发射光谱在591,612,701 nm处呈现Eu³⁺的⁵Do—⁷F₁,⁵Do—⁷F₂,⁵D₀—⁷F₄的特征发射.并且当固定Eu³⁺的浓度时,随着Bi³⁺含量的增加,发现Bi³⁺,Eu³⁺在这一体系中存在能量传递现象,系列样品发光强度大幅度提高.通过研究系列样品在不同Bi³⁺,Eu³⁺掺杂浓度下的发光性能,得出最佳样品为Mg_4.89Eu_0.1Bi_0.01SnB₂O₁₀,其积分强度达到了商用Y₂O₂S:Eu³⁺的1.1倍.     

Y2O3:Eu纳米晶中能量传递相互作用的研究

通过浓度猝灭曲线确定了引起Y₂O₃纳米晶中Eu³⁺发光浓度猝灭的是交换相互作用.测量了两种颗粒尺寸下Eu³⁺的⁵D₀—⁷F₂跃迁发光衰减曲线随掺杂浓度的变化,利用交换相互作用的理论衰减曲线对实验衰减曲线进行拟合.计算Eu³⁺离子的交换相互作用能量传递的效率,分析了Y₂O_{3关键词： 能量传递 2}O₃Eu纳米晶')" href="#">Y₂O₃Eu纳米晶 发光衰减     

Sr2+掺杂荧光粉Ca2Nb2O7：Eu3+的发光特性

采用高温固相法制备出Ca_1.97-xSr_xNb₂O₇：3%Eu³⁺（x=0.10,0.50,1.0,1.5,1.97）红色荧光粉,研究了Ca_1.97-xSr_xNb₂O₇：3%Eu³⁺的发光特性及Sr²⁺的浓度对该荧光粉发光性质的影响。随着Sr²⁺浓度的改变,Ca_2-xSr_xNb₂O₇：Eu³⁺的XRD呈现不同的相。Ca_1.97Nb₂O₇：3%Eu³⁺（x=0）的激发光谱中,302 nm附近的强宽带来自于O^2-→Eu³⁺电荷转移跃迁,272 nm附近的肩峰来自于NbO^7-₆基团的电荷转移跃迁,350~600 nm范围内的锐锋属于Eu³⁺的特征4f-4f组内跃迁。在398 nm激发下,发射光谱的最强峰位于616 nm,属于Eu³⁺的⁵D₀→⁷F₂电偶极跃迁,发射出强烈的红光。当Ca²⁺逐渐被Sr²⁺取代时,Ca_2-xSr_xNb₂O₇：Eu³⁺的各激发峰的强度先提高后降低,且O^2-→Eu³⁺电荷转移跃迁发生明显红移。少量Sr²⁺的掺杂可以有效提高Ca_2-xSr_xNb₂O₇：Eu³⁺ 的红光发射强度,当x=0.01时该荧光粉的红光发射达到最强,可以被紫外LED芯片激发。     

H_3BO_3对Y_(1.98)O_3:Eu_(0.01),Dy_(0.01)红色长余辉发光材料结构和余辉性能的影响

采用高温固相法制备了发光样品Y1.98O3:Eu3+0.01,Dy3+0.01.采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、荧光光谱仪、单光子计数器测试了不同含量的H3BO3对Y1.98O3:Eu3+0.01,Dy3+0.01物相结构、颗粒形貌、发光性能、余辉性能的影响.结果表明当H3BO3含量低于8%(mol)时,样品可保持Y2O3晶格结构,且样品颗粒随H3BO3的含量增加逐渐增大.样品光致发光由Eu3+离子电子的5D0→7FJ跃迁所致,主峰位于612 nm,且发光强度随H3BO3含量的增加呈线性增强.随着H3BO3含量的增加,样品余辉衰减时间逐渐增加,热释光谱分析表明H3BO3的加入增加了基质陷阱能级的深度与浓度,故而导致样品长余辉性能的变化.     

Phosphorescent and thermoluminescent properties of SrAl2O4:Eu,Dy phosphors prepared by solid state reaction method

Long persistent SrAl₂O₄:Eu²⁺ phosphors co-doped with Dy³⁺ were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl₂O₄ were observed in all the samples. The broad band emission spectra at 497 nm for SrAl₂O₄:Eu²⁺, Dy³⁺ were observed and the emission is attributed to the 4f⁶5d¹ to 4f⁷ transition of Eu²⁺ ions. The samples annealed at 1100–1200 °C showed similar broad TL glow curves centered at 120 °C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy³⁺ ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.     

Luminescent characteristics of LiCaBo3:M (M=Eu, Sm, Tb, Ce, Dy) phosphor for white LED

LiCaBO₃:M (M=Eu³⁺, Sm³⁺, Tb³⁺, Ce³⁺, Dy³⁺) phosphors were synthesized by a normal solid-state reaction using CaCO₃, H₃BO₃, Li₂CO₃, Na₂CO₃, K₂CO₃, Eu₂O₃, Sm₂O₃, Tb₄O₇, CeO₂ and Dy₂O₃ as starting materials. The emission and excitation spectra were measured by a SHIMADZU RF-540 UV spectrophotometer. And the results show that these phosphors can be excited effectively by near-ultraviolet light-emitting diodes (UVLED), and emit red, green and blue light. Consequently, these phosphors are promising phosphors for white light-emitting diodes (LEDs). Under the condition of doping charge compensation Li⁺, Na⁺ and K⁺, the luminescence intensities of these phosphors were increased.     

Dy含量对红色长余辉发光材料Sr3Al2Ｏ6:Eu2＋,Dy3＋性能的影响

采用溶胶凝胶法制备了Sr₃Al₂Ｏ₆:Eu^2＋,Dy^3＋红色长余辉发光材料,利用X射线衍射仪对材料的物相进行了分析,结果表明,1200℃下制备的样品的物相为Sr₃Al₂Ｏ₆,少量的Eu和Dy掺杂没有影响样品的相组成.采用荧光分光光度计、照度计测定了样品的发光特性.结果表明Sr₃Al₂Ｏ关键词： 红色长余辉 3Al₂Ｏ₆')" href="#">Sr₃Al₂Ｏ₆ 溶胶凝胶法     

Enhanced luminescent properties of long-persistent Sr2MgSi2O7:Eu, Dy phosphor prepared by the co-precipitation method

Sr₂MgSi₂O₇:Eu²⁺, Dy³⁺ phosphors were prepared by the (aminopropyl)-triethoxysilane (APTES) co-precipitation method. Effects of synthesis temperature on the crystal characteristics, luminescent properties and afterglow performance of Sr₂MgSi₂O₇:Eu²⁺, Dy³⁺ phosphors have been discussed in detail and compared with the corresponding commercial product. The experimental results indicated that the sample could be synthesized at a relatively lower temperature and had better performance on the above-mentioned properties using the co-precipitation method.     

The effect of flux materials on the physical and optical properties of Eu-activated yttrium oxide phosphors

A flux fusion method was used to obtain the various sizes of Eu³⁺-activated Y₂O₃ red phosphors. The flux material was selected as an independent variable to control the physical properties of phosphor particles and their effects on the morphology and size distribution of phosphors were examined by scanning electron microscopy. The concentration of the flux materials and synthetic temperature were optimized for maximal photoluminescence intensity. Fluoride-based flux materials were found to work for the crystal formation of Eu³⁺-activated Y₂O₃. In particular, when a BaF₂ flux was used during the reaction at 1450 °C for 3 h, the photoluminescence (PL) intensity of Eu³⁺-activated Y₂O₃ was 25% higher than that without a flux and spherical phosphors had a mean particle size of 4-5 μm. The morphology and size distribution of the synthesized Eu³⁺-activated Y₂O₃ phosphor were predominantly dependent upon the type and concentration of flux material and synthetic temperature.     

Synthesis and characterization of Sr3Al2O6：Eu2＋, Dy3＋ phosphors prepared by sol-gel-combustion processing

A type of red luminescent Sr3Al2O6:Eu2+, Dy3+ phosphor powder is synthesised by sol-gel-combustion processing, with metal nitrates used as the source of metal ions and citric acid as a chelating agent of metal ions. By tracing the formation process of the sol-gel, it is found that it is necessary to reduce the amount of NO3- by dropping ethanol into the solution for forming a stable and homogeneous sol-gel. Thermogravimetric and Differential Scanning Calorimeter Analysis, x-ray diffractionmeter, scanning electron microscopy and photoluminescence spectroscopy are used to investigate the luminescent properties of the as-synthesised Sr3Al2O6:Eu2+, Dy3+. The results reveal that the Sr3Al2O6 crystallises completely when the combustion ash is sintered at 1250 C. The excitation and the emission spectra indicate that the excitation broadband lies mainly in a visible range and the phosphors emit a strong light at 618 nm under the excitation of 472 nm. The afterglow of (Sr0.94Eu0.03Dy0.03)3Al2O6 phosphors sintered at 1250 ℃ lasts for over 1000 s when the excited source is cut off.     

Effect of Sr substitution on photoluminescent properties of BaAl2O4:Eu, Dy

Phosphor material BaAl₂O₄:Eu²⁺, Dy³⁺ with varying compositions of Sr substitution were prepared by the solid-state synthesis method. The phosphor compositions were characterized for their phase and crystallinity by XRD, SEM and TEM. Photoluminescence (PL) properties were investigated measuring PL and decay time for varying Ba/Sr compositions. The PL results show the blue shift in the luminescence properties in Sr substituted BaAl₂O₄:Eu²⁺, Dy³⁺ compared to parent BaAl₂O₄:Eu²⁺, Dy³⁺. It is probably due to the influence of 5d electron states of Eu²⁺ in the crystal field because of atomic size variation causing crystal defects. Dy³⁺ ion doping in the phosphor generates deep traps, which results in long afterglow phosphorescence.     

发光二极管用红色荧光粉Sr0.8-xBaxEu0.2WO4的制备和性质研究

采用化学共沉淀法制备了不同Ba²⁺掺杂浓度、 不同煅烧温度的Sr_0.8-xBa_xEu_0.2WO₄红色荧光粉. 研究了样品的晶体取向和晶格 畸变对发光性质的影响, 实验结果表明: 合成的Sr_0.8-xBa_xEu_0.2WO₄红色荧光粉为四方相, 样品中Eu³⁺的⁵D₀–⁷F₂跃迁的红光能被近紫外光和蓝光有效激发. 适量的Ba²⁺离子取代部分的Sr²⁺提高了Sr_0.8Eu_0.2WO₄荧光粉的发光强度, Ba²⁺掺杂浓度的改变对基质的晶格参数、晶体对称性和发光性能影响较大, Ba²⁺的最佳掺杂量为30%.     

Photoluminescence and afterglow behavior of Eu, Dy and Eu, Dy in Sr3Al2O6 matrix

This paper reports the photoluminescence and afterglow behavior of Eu²⁺ and Eu³⁺ in Sr₃Al₂O₆ matrix co-doped with Dy³⁺. The samples containing Eu²⁺ and Eu³⁺ were prepared via solid-state reaction. X-ray diffraction (XRD), photo luminescent spectroscope (PLS) and thermal luminescent spectroscope (TLS) were employed to characterize the phosphors. The comparison between the emission spectra revealed that Sr₃Al₂O₆ phosphors doped with Eu²⁺, Dy³⁺ and Eu³⁺, Dy³⁺ showed different photoluminescence. The phosphor doped with Eu³⁺, Dy³⁺ showed an intrinsic f-f transition generated from Eu³⁺, with two significant emissions at 591 and 610 nm. However, the phosphor doped with Eu²⁺, Dy³⁺ revealed a broad d-f emission centering around 512 nm. After the UV source was turned off, Eu²⁺, Dy³⁺ activated Sr₃Al₂O₆ phosphor showed excellent afterglow while Eu³⁺, Dy³⁺ activated phosphor almost showed no afterglow. Thermal simulated luminescence study indicated that the persistent afterglow of Sr₃Al₂O₆: Eu²⁺, Dy³⁺ phosphor was generated by suitable electron traps formed by the co-doped rare-earth ions (Dy³⁺) within the host.