对撞脉冲锁模环形染料激光器的运转特性(英文)

研究了用DODCI和DQOCI染料作为可饱和吸收体的对撞脉冲锁模环形染料激光器的运转特性。提供锁模脉冲宽度、激光器以稳定单脉冲工作的稳定性范围和阈值泵浦功率等,对吸收体染料浓度依赖关系的测试结果。表明了用此激光器,在低的泵浦功率(约2W)下,日常能产生脉宽为0.12ps、峰值功率为1kW的稳定脉冲。给出用光谱分辨的二次谐波自相关法测量输出脉冲的结果,证实在锁模脉冲中已发生频率调制。实验中发现用DQOCI染料作为可饱和吸收体时,激光输出光谱由黄光和红光两个分立部分构成。当黄光的振荡被抑制时,锁模稳定性改善且输出脉冲形状整齐、前后沿包含很小的能量。     

一种基于增益调制技术的全光纤化脉冲Yb光纤激光器

以波长为975 nm的半导体激光器作为泵浦源,周期性地脉冲泵浦一个包含Yb掺杂光纤和光纤光栅对的Yb光纤激光器,实现了基于增益调制技术的全光纤化高功率Yb光纤激光器的稳定脉冲输出.在50 kHz重频下,采用20 W的泵浦功率和2.4 μs的泵浦脉冲宽度,获得了1 060 nm波长脉冲宽度仅100 ns的稳定脉冲激光输出,单脉冲激光能量约为20 μJ.以此作为脉冲激光种子进行功率放大,获得了性能稳定的全光纤结构高功率脉冲激光输出,放大后单脉冲能量超过200 μJ,激光放大器斜率效率达到60%.     

分布反馈激光特性的实验研究

研究了以脉冲YAG倍频激光泵浦Rh6G染料,产生分布反馈激光振荡的辐射光谱、转换效率、时间过程以及可调谐特性;发现在大于泵浦阈值下的分布反馈激光输出的多谱线结构与双脉冲辐射现象,以及分布反馈激光脉冲变窄的自开关效应.作为详细的实验观察和分析.     

基于全保偏光纤利用脉冲同步技术差频产生中红外皮秒激光

搭建了主-从结构的全光被动同步激光器,将主激光器输出脉冲功率放大后注入从激光器,利用注入脉冲在从激光器中的交叉相位调制效应,实现了1029.9 nm泵浦光与1585.5 nm信号光的脉冲同步。采用声光调制器进行选频并配合级联光纤放大,提高了泵浦光脉冲的峰值功率,并通过优化光纤链路长度有效控制了泵浦光光谱展宽。该双色同步脉冲在PPLN晶体中进行非线性差频处理,当重复频率为100 kHz时,获得了3 dB光谱带宽为0.77 nm、中心波长为2940 nm的线偏振皮秒脉冲,最大单脉冲能量为1.8μJ,泵浦光转化效率为49.6%。     

紫外超短脉冲激光的单次测量

 利用瞬态光栅衍射法研制了一台单次频率分辨光学开关激光参数测量仪,可以对脉宽范围在10 ps以内的紫外超短脉冲激光进行单次测量。利用该仪器对重复频率为10 Hz的放电泵浦和单次运行的电子束泵浦KrF准分子激光器的输出脉冲分别进行了单次测量,结果表明：对于放电泵浦,当系统工作在零啁啾附近时,脉冲波形和光谱分布较规则,相位分布起伏较小,当系统偏离零啁啾状态时,脉冲波形和光谱分布不再规则,并且相位分布为抛物线结构;对于单次运行的电子束泵浦,脉冲波形具有多峰结构,光谱具有复杂的调制,脉宽约为2 ps,带宽约为1.3 nm,相位分布为抛物线结构。     

同步泵浦染料激光中的频率啁啾计算

利用光场的自洽模型，将同步泵浦染料激光器的输出光脉冲的频率啁啾β作为光波场的位相参数，推导出适合于同步泵浦染料激光器的锁模方程．由此方程出发，求出输出光脉冲频率啁啾β的解析表达式，为实验上减小脉冲的频率啁啾，获得符合变换极限的短脉冲提供依据．     

宽光谱全正色散锁模掺镱光纤激光器

介绍了一种全正色散宽光谱被动锁模掺镱光纤激光器,利用非线性偏振旋转技术实现全正色散掺镱光纤激光器的被动锁模.当泵浦功率输出为500mW时,激光脉冲输出功率大于139mW,重复频率约为28.1MHz,脉冲宽度为3.8ps.为了进一步研究全正色散光纤激光器的宽光谱输出特性,在腔内熔接50m单模光纤,同时去除双折射滤波片,在泵浦功率为500mW时,观察到稳定锁模单脉冲耗散孤子,光谱范围为1 005~1 140nm,输出激光脉冲最大平均功率为90mW,重复频率为3.58MHz,脉冲宽度为519ps.     

全光纤主动锁模2 μm掺铥脉冲激光器

报道了全光纤结构主动锁模掺铥脉冲激光器,中心波长为1950 nm。利用电光相位调制器对光纤激光器进行腔内相位调制,获得了重复频率为11.884 MHz的主动锁模脉冲输出,脉宽为816 ps。改变泵浦功率、调制信号的频率和幅度,获得了重复频率为4~18 kHz的弛豫振荡调制稳定脉冲输出。锁模和弛豫振荡调制获得的输出脉冲能量波动低于7%。     

高温LDAs泵浦紧凑型Nd:YAG激光器

设计了一套紧凑型高温激光二极管阵列端面泵浦电光调Q Nd∶YAG激光器。为使激光器整体结构紧凑,以高温激光二极管阵列作为泵源以有效地降低Nd∶YAG激光器散热压力。利用Ansys软件对高温激光二极管阵列工作时的温度场进行模拟。使用基于K9玻璃材质的导光锥将泵浦光耦合进Nd∶YAG晶体内。利用Traceproc软件模拟了导光锥前后端面的光场分布。采用5mm×5mm×40mm、掺杂浓度为1.0at。%的Nd∶YAG晶体作为增益介质,利用Ansys软件对200μs,250μs泵浦脉宽条件下的晶体内部温度场分布进行模拟并计算了激光器工作时的热透镜焦距。结果表明,本文设计的紧凑型激光器可以实现稳定的脉冲激光输出。在重复频率20Hz,泵浦源电压脉冲宽度250μs、300μs条件下,获得了单脉冲能量44.1mJ和50.2mJ的单脉冲输出,对应脉冲宽度分别为18.3ns和21.3ns,斜效率为12.35%和12.24%.     

光源稳定性对简并四波混频信噪比影响的实验研究

在碘蒸气中研究了染料激光稳定性对简并四波混频(DFWM)信噪比的影响。实验中采用多模Nd∶YAG激光器倍频的输出泵浦染料激光器(染料PM580溶于酒精)。在具有前向补偿分光系统和图像探测系统的帮助下,在常温常压条件下测得泵浦光在波长为554.013 nm时达到饱和光强为290 μJ。同时发现染料激光器的光稳定性(输出波长范围,光束质量和能量转换效率等)随使用时间,泵浦激光脉冲次数和能量的增加而逐渐减弱。另外通过对比发现在染料激光器输出不稳定时,光源单色性和指向性等指标的变化导致在同一泵浦强度不同时刻获得的DFWM信号强度相差很大,且DFWM信号信噪比低。染料激光器光源稳定性对DFWM信号影响的研究结果对物质的痕迹量探测以及无荧光物质光谱定标等方面的应用具有重要意义。     

10 ps High Power Laser System at 248 nm

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｉｎｒｅｃｅｎｔｙｅａｒｓｔｈｅｒｅｈａｓｂｅｅｎａｎｉｎｔｅｎｓｉｖｅｅｆｆｏｒｔｄｉｒｅｃｔｅｄｔｏｗａｒｄｔｈｅｐｒｏｄｕｃｔｉｏｎｏｆｓｈｏｒｔｐｕｌｓｅ,ｈｉｇｈ ｐｏｗｅｒＵＶｌａｓｅｒｓｙｓｔｅｍｓ .ＫｒＦｌａｓｅｒ,ｗｉｔｈｉｔｓ～ 2ｎｍｂａｎｄｗｉｄｔｈ ,ｈｉｇｈｅｌｅｃｔｒｉｃａｌ ｔｏ ｏｐｔｉｃａｌｃｏｎｖｅｒｓｉｏｎｅｆｆｉｃｉｅｎｃｙａｎｄｉｔｓｕｎｂｏｕｎｄ ｇｒｏｕｎｄｓｔａｔｅ ,ｉｓａｎａｔｔｒａｃｔｉｖｅｃａｎｄｉｄａｔｅｆｏｒｔｈｅ…     

10 ps High Power Laser System at 248 nm

A simple 10 ps KrF laser system consisting of quenched dye laser oscillator pumped by a XeCl laser, a distributed feedback dye laser (DFDL), a three-stage dye amplifier and a two-stage KrF amplifier are described. The output of the laser system is 140 mJ with 10 ps pulse width by using polarization-multiplexing amplification. A focused output laser intensity of about 4×1015 W/cm2 is obtained. The saturation fluence for KrF laser is obtained with this laser.     

20 ps pulse generation by an excimer laser pumped double self-Q-switched distributed feedback dye laser

The behaviour of an excimer-laser-pumped distributed feedback dye laser (ELP DFDL) using a mixture of saturable absorber and laser dye as an active medium was studied. In a DFDL self-Q-switching occurs because of the population inversion dependence of the feedback. If the DFDL contains absorber saturation of the absorption by the leading edge of the created laser pulse also causes Q-switching. As a result of this double self-Q-switching, mixing a saturable absorber into the laser dye, the laser pulses become shorter and more stable. This was demonstrated experimentally. Mixing Rhodamine B into the dye solution of a Coumarin 153 ELP DFDL, a six-fold reduction in the pulse duration and a more than two-fold reduction in the pulse energy instability were observed. The experimental results were in good qualitative agreement with the predictions of a simple rate equation model.     

Tunable energy transfer distributed feedback dye laser using pyronin B and crystal violet dye mixture

Using pyronin B and crystal violet dye mixture, the characteristics of energy transfer distributed feedback dye laser (ETDFDL) pumped by 532 nm Nd:YAG laser were investigated. The characteristics of donor DFDL and acceptor DFDL as well as the dependence of their pulse widths and output powers on pump power and acceptor concentrations were studied. The output energy of DFDL was measured at the emission peaks of donor and acceptor dyes for different pump powers and acceptor concentrations, and tunability was observed from 570 to 645 nm using prism dye cell arrangement.     

New single-pulse generation technique for distributed feedback dye lasers

The distributed feedback dye laser (DFDL) generates a train of picosecond pulses when pumped well above threshold. This DFDL emission can be quenched by injecting a laser pulse into DFDL. By proper timing of the quencher laser pulse, only the first DFDL pulse is generated while the successive pulses are suppressed. Operational characteristics and practical design considerations of such a quenched DFDL are given. With 2.5 ns long pump pulses from a N₂ laser, a shortest DFDL pulse of 17 ps was obtained at 380 nm.     

Mathematical modeling of ruby laser as a pumping source of a “self Q-switched” distributed feedback dye laser

A mathematical model describing the dynamic emission of the ruby laser as a pumping source of a distributed feedback dye laser (DFDL) has been adapted. The suggested model allows the temporal behavior investigation of the ruby laser and the DFDL on mode characteristics and, moreover, investigating the affect of laser input parameters on the output laser pulses in the ruby laser and in the DFDL.The numerical solutions of a coupled nonlinear rate equations system of the adapted model that predict the generation of picoseconds pulses, with neglecting the effect of refractive index variation, are discussed (feedback process is achieved only by optical gain). The model estimates the density of the emitted radiation, energy density of the first excited state, and the output power of the DFDL. The adapted mathematical model is in good agreement with the available experimental data.     

Tunable picosecond energy transfer distributed feedback dye laser using Rhodamine 6G and Thionine dye mixture

The characteristics of Nd:YAG laser pumped energy transfer distributed feedback dye laser (ETDFDL) is studied both theoretically and experimentally. Using theoretical model proposed the behaviour of ETDFDL for dye mixture Rhodamine 6G and Thionine is studied in detail. The characteristics of donor DFDL, the acceptor DFDL, the dependence of their pulse widths and output powers on donor–acceptor concentration and pump power are studied. The output energy of DFDL is measured experimentally at the emission peaks of donor and acceptor dyes for different pump powers and donor–acceptor concentrations. In addition, the tunability of DFDL emission is measured both in donor and acceptor emission ranges.     

Properties of a distributed feedback dye laser with integrated amplifier

Several properties of a compact laser light source built up by a distributed feedback dye laser (DFDL) and an amplifier realized with only one dye solution cuvette are discussed. It is shown that in this arrangement the region of single pulse generation with respect to the pump energy applied to the DFDL is extended in comparison with a pure DFDL oscillator set-up. This effect is mainly caused by the radiation coupled back from the amplifier into the DFDL oscillator. The results of numerical simulations are discussed and compared with some experimental facts published in a previous paper.     

Studies on widely tunable ultra-short laser pulses using energy transfer distributed feedback dye laser

This paper presents both theoretical and experimental study of the characteristics of Nd: YAG laser pumped energy transfer distributed feedback dye laser (ETDFDL). Using theoretical model proposed, the behavior of ETDFDL such as the characteristics of donor DFDL, the acceptor DFDL, the dependence of their pulse width and output power on donor-acceptor concentrations and pump power are studied for dye mixture Rhodamine 6G and Cresyl Violet in detail. Experimentally using prism-dye cell configuration, the ETDFDL output is obtained and the output energy of DFDL is measured at the emission peaks of donor and acceptor dyes for different pump powers and donor-acceptor concentrations. In addition, the DFDL linewidth measurement has been carried out at the lasing wavelengths of the donor and acceptor dyes using Fabry-Perot etalon and the tunability of DFDL is measured to be in the wavelength range of 545-.     

Modeling a distributed feedback dye laser pumped by a Nd-glass laser

A mathematical model has been developed to describe the dynamic emission of a distributed feedback dye laser (DFDL) pumped by a Nd-glass laser. The model is based on the coupled-wave theory. It allows the investigation of the temporal behavior of the Nd-glass pumping laser source and the DFDL pulses. The model allows studying the effect of the variation of the laser input parameters of the Nd-glass laser, such as maximum amplification coefficient, loss coefficient and pumping rate on the characteristics of DFDL pulses regarding the pulse width, delay time and separation time. The feedback process of the DFDL is provided either by changes of the refractive index or by optical gain or by both together. The model estimates the following: temporal behavior of the density of emitted radiation, energy densities of the first excited singlet and triplet states, DFDL output power, cavity decay time and the temperature of the produced grating. The numerical solution of the nonlinear coupled rate equation system predicts the generation of DFDL picosecond pulses. The calculated results are in good agreement with the available experimental data. The calculations were done using rhodamine 6G dissolved in ethanol as the investigated matrix.