Photoluminescence from amorphous silica nanowires synthesized using TiN/Ni/SiO2/Si and TiN/Ni/Si substrates

Photoluminescence characteristics of amorphous silica nanowires (a-SiONWs) grown on TiN/Ni/Si and TiN/Ni/SiO₂ substrates have been studied. A-SiONWs grown on TiN/Ni/Si substrates show a Si-rich composition compared to those grown from TiN/Ni/SiO₂/Si. The emission characteristics of the nanowires were found to depend on the type of substrate. By annealing the a-SiONWs grown on TiN/Ni/Si in air, emission bands shift from blue to green bands. It is likely that silicon to oxygen ratio is an important factor in deciding the types of defects and emission bands of amorphous silica nanowires.     

The structure of ordered Au films on TiOx

The growth of Au on an ultra-thin, ordered Mo(1 1 2)-(8 × 2)-TiO_x, was investigated using scanning tunneling microscopy (STM), low energy ion scattering spectroscopy (LEISS), X-ray photoelectron spectroscopy (XPS), and temperature programmed desorption (TPD). Wetting of the TiO_x surface by Au was observed with STM and LEISS, and the ordering of the Au films was atomically resolved with STM. TPD showed that Au binds more strongly to the reduced TiO_x film than to bulk TiO₂, but more weakly than to the Mo substrate. The Au-TiO_x binding energy is greater than Au-Au in bulk Au. The oxidation state of Ti in the TiO_x film was deduced by XPS and from the Ti-O phonon shifts relative to bulk TiO₂. The TiO_x/Mo(1 1 2) film structure and those for the (1 × 1)- and (1 × 3)-Au/TiO_x/Mo(1 1 2) surfaces are discussed.     

Structural properties of Al2O3 dielectrics grown on TiN metal substrates by atomic layer deposition

We investigated on the structural properties of Al₂O₃ dielectrics grown on TiN metal substrates using an atomic layer deposition technique with tri-methyl-aluminum and either O₃ or H₂O as the precursor and oxidant, respectively. The structural and morphological features of these films were examined by atomic force microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy measurements. We find that Al₂O₃ dielectric films with the O₃ oxidant exhibit a rough morphology, a thick TiO₂ film, and a small amount of contaminants such as carbon and hydrogen. The reason for the rapid diffusion of oxygen atoms into the TiN lattice leads to the formation of TiO₂ layer on the TiN substrate. This is due to the higher oxidation potential of the O₃ compared to the H₂O.     

Bilayer period effect on corrosion-erosion resistance for [TiN/AlTiN]n multilayered growth on AISI 1045 steel

The aim of this work is to study the electrochemical behavior, under a corrosion-erosion condition, of [TiN/AlTiN]_n multilayer coatings with bilayers periods of 1, 6, 12 and 24, deposited by a magnetron sputtering technique on Si (1 0 0) and AISI 1045 steel substrates.The TiN and AlTiN structure for multilayer coatings were evaluated via X-ray diffraction (XRD) analysis. Silica particles were used as an abrasive in the corrosion-erosion test within a 0.5 M H₂SO₄ solution at an impact angle of 30° over the surface. The electrochemical characterization was carried out using a polarization resistance technique (Tafel), in order to observe changes in the corrosion rate as a function of the bilayers number (n) or bilayer period (Λ). Corrosion rate values of 359 mpy in uncoated steel substrate and 1.016×10⁻⁶ mpy for substrate coated with [TiN/AlTiN]₂₄ under impact angle of 30° were found. This behavior was related with the mass loss curve for all coatings and the surface damage was analyzed using SEM images. These results indicate that TiN/AlTiN multilayer coatings deposited on AISI 1045 steel provide a practical solution for applications in erosive-corrosive environments.     

Substrate effects on the oxygen gas sensing properties of SnO2/TiO2 thin films

In this study, SnO₂/TiO₂ thin films are fabricated on SiO₂/Si and Corning glass 1737 substrates using a R.F. magnetron sputtering process. The gas sensing properties of these films under an oxygen atmosphere with and without UV irradiation are carefully examined. The surface structure, morphology, optical transmission characteristics, and chemical compositions of the films are analyzed by atomic force microscopy, scanning electron microscopy and PL spectrometry. It is found that the oxygen sensitivity of the films deposited on Corning glass 1737 substrates is significantly lower than that of the films grown on SiO₂/Si substrates. Therefore, the results suggest that SiO₂/Si is an appropriate substrate material for oxygen gas sensors fabricated using thin SnO₂/TiO₂ films.     

Formation of silicon nanodots from dysprosium-doped amorphous SiCxOy films grown by hot-filament assisted chemical vapor deposition of CH3SiH3 and Dy(DPM)3 gas jets

We report on Si nanodot formation by chemical vapor deposition (CVD) of ultrathin films and following oxidation. The film growth was carried out by hot-filament assisted CVD of CH₃SiH₃ and Dy(DPM)₃ gas jets at the substrate temperature of 600 °C. The transmission electron microscopy observation and X-ray photoelectron spectroscopy analysis indicated that ∼35 nm Dy-doped amorphous silicon oxycarbide (SiC_xO_y) films were grown on Si(1 0 0). The Dy concentration was 10-20% throughout the film. By further oxidation at 860 °C, the smooth amorphous film was changed to a rough structure composed of crystalline Si nanodots surrounded by heavily Dy-doped SiO₂.     

Properties of CuIn(SxSe1−x)2 polycrystalline thin films prepared by chemical spray pyrolysis

CuIn(S_xSe_1−x)₂ thin polycrystalline films were grown by the chemical spray pyrolysis method on the glass substrate at 280-400°C. The alloy composition in the film was studied with relation to that in the splay solution. Films were characterized by X-ray diffraction, optical absorption, Raman spectroscopy, resistivity and surface morphology. The CuInSe₂-rich alloy films grown at high substrate temperature had chalcopyrite structure, while, the CuInS₂-rich films grown at low substrate temperature exhibited sphalerite structure. Optical-gap energies were smaller than that of the bulk crystal by 0.1-0.2 eV for CuInS₂-rich films. Raman spectra exhibited both CuInSe₂-like and CuInS₂-like A₁ modes, and their relative changed systematically with alloy composition.     

Helical nanostructures of SiOx synthesized through the heating of Co-coated substrates

This paper presents the use of the simple annealing technique at 1000 °C to produce the helical nanostructures of SiO_x. We have employed the Co-coated Si substrates, with Co layer and Si substrate utilized as catalyst and Si source, respectively. Beside the ordinary straight nanowires, the helical nanowires such as nanosprings and nanorings were observed. The product was an amorphous structure of SiO_x. We have discussed the possible growth mechanism. Photoluminescence spectrum of the SiO_x nanostructures showed a blue emission at 428 nm and a green emission at 534 nm, respectively.     

The influence of Co doping on the dielectric, ferroelectric and ferromagnetic properties of Ba0.70Sr0.30TiO3 thin films

Ba_0.70Sr_0.30TiO₃ (BST) thin films doped by Co (BSTC) are fabricated by sol-gel method on a Pt/Ti/SiO₂/Si substrate. A strong correlation is observed among the microstructure, dielectric, ferroelectric, ferromagnetic properties and Co concentration. The dielectric constant of BST thin films can be tailored from 343 to 119 by manipulating the Co concentration. The dielectric loss of BSTC thin films are still kept below 0.020 and the tunability is above 30% at a dc-applied electric field of 500 kV/cm. With increasing Co doping up to 10 mol%, the coexistence of ferromagnetism and ferroelectrics is found. Suitable dielectric constant, low-dielectric loss, and high tunability of this kind of thin films can be useful for potential tunable applications.     

Bipolar switching properties of amorphous TiO2 thin film grown on TiN/Si substrate

Pt/TiO₂/TiN device with the amorphous TiO₂ film grown at room temperature under an oxygen partial pressure of 1.0 mTorr showed reliable bipolar switching behavior. During the electroforming process, a large number of oxygen vacancies formed in the TiO₂ film and accumulated at the Pt/TiO₂ interface. The barrier height of the Schottky contact of the Pt/TiO₂ interface was reduced owing to the presence of these oxygen vacancies, resulting in the low-resistance state (LRS). Moreover, oxygen ions diffused into the TiN electrode during the electroforming and set processes. On the other hand, the oxygen ions in the TiN electrode diffused out and reacted with oxygen vacancies in the TiO₂ film during the reset process, and the device changed from the LRS to the high-resistance state (HRS). Conduction in the LRS and HRS can be attributed to Ohmic conduction and the trap controlled space charged limited mechanism, respectively.     

Thermal stability and chemical bonding states of AlOxNy/Si gate stacks revealed by synchrotron radiation photoemission spectroscopy

Annealing-temperature dependence of the thermal stability and chemical bonding states of AlO_xN_y/SiO₂/Si gate stacks grown by metalorganic chemical vapor deposition (MOCVD) using new chemistry was investigated by synchrotron radiation photoemission spectroscopy (SRPES). Results have confirmed the formation of the AlN and AlNO compounds in the as-deposited samples. Annealing the AlO_xN_y samples in N₂ ambient in 600-800 °C promotes the formation of SiO₂ component. Meanwhile, there is no formation of Al-O-Si and Al-Si binding states, suggesting no interdiffusion of Al with the Si substrate. A thermally induced reaction between Si and AlO_xN_y to form volatile SiO and Al₂O is suggested to be responsible for the full disappearance of the Al component that accompanies annealing at annealing temperature of 1000 °C. The released N due to the breakage of the Al-N bonding will react with the SiO₂ interfacial layer and lead to the formation of the Si₃-N-O/Si₂-N-O components at the top of Si substrate. These results indicate high temperature processing induced evolution of the interfacial chemistry and application range of AlO_xN_y/Si gate stacks in future CMOS devices.     

Formations and morphological stabilities of ultrathin CoSi2 films

In this paper we investigate the formations and morphological stabilities of Co-silicide fihns using 1-8-nm thick Co layers sputter-deposited on silicon （100） substrates. These ultrathin Co-silicide films are formed via solid-state reaction of the deposited Co films with Si substrate at annealing temperatures from 450 ℃ to 850 ℃. For a Co layer with a thickness no larger than i nm, epitaxially aligned CoSi2 films readily grow on silicon （100） substrate and exhibit good morphological stabilities up to 600 ℃. For a Co layer thicker than 1 nm, polycrystalline CoSi and CoSi2 films are observed. The critical thickness below which epitaxially aligned CoSi2 film prevails is smaller than the reported critical thickness of the Ni layer for epitaxial alignment of NiSi2 on silicon （100） substrate. The larger lattice mismatch between the CoSi2 film and the silicon substrate is the root cause for the smaller critical thickness of the Co layer.     

New fabrication of a strained Si/Si1−yGey dual channel on a relaxed Si1−xGex virtual substrate using a Ge-rich layer formed by oxidation

This paper presents a new method of forming a Si/SiGe dual channel on a Si_0.8Ge_0.2 virtual substrate. Generally, in a CMOS process using a Si/SiGe dual channel, due to several processes involving ion-implantation, annealing and dry-etching after the deposition of the Si/SiGe dual channel, the surface can be damaged, leading to reduced electrical properties. However, if the dual channel is formed during a specific stage of the CMOS process, the defects of the dual channel can be reduced and the thermal stability will be excellent. Therefore, in this paper, a method for minimizing the defects of the dual channel is presented. This method uses the segregation of the Ge in the oxidation process of a SiGe. A Si/SiGe dual channel formed using this method achieved results that were identical to a dual channel deposited using the chemical vapor deposition (CVD) method.     

Superhydrophilic stability enhancement of RF co-sputtered TixSi1−xO2 thin films in dark

Ti_xSi_1−xO₂ compound thin-film systems were deposited by reactive RF magnetron co-sputtering technique. The effect of Ti concentration on the hydrophilicity of Ti_xSi_1−xO₂ compound thin films was studied and it was shown that the films with Ti_0.6Si_0.4O₂ composition possess the best hydrophilic property among all the grown samples. Surface ratio and average roughness of the thin films were measured by atomic force microscopy (AFM). Surface chemical states and stoichiometry of the films were determined by X-ray photoelectron spectroscopy (XPS). In addition, XPS revealed that the amount of Ti-O-Si bonds in nanometer depth from the surface of the Ti_0.6Si_0.4O₂ films was the maximum, which resulted in the most stable superhydrophilic property. According to XRD data analysis for the pure TiO₂ films, the polycrystalline anatase phase was formed with an average grain size of about 15 nm. Moreover, amorphous phase was also formed for the Ti_xSi_1−xO₂ compound systems due to presence of silicon in the films. Finally, optical properties of the films such as transmission, reflection and band gap energy were investigated using UV-vis spectrophotometry. It was found that the transmittance of the films was decreased with increasing Ti concentration in the films.     

Fabrication of multilayered Ge nanocrystals embedded in SiOxGeNy films

Multilayered Ge nanocrystals embedded in SiO_xGeN_y films have been fabricated on Si substrate by a (Ge + SiO₂)/SiO_xGeN_y superlattice approach, using a rf magnetron sputtering technique with a Ge + SiO₂ composite target and subsequent thermal annealing in N₂ ambient at 750 °C for 30 min. X-ray diffraction (XRD) measurement indicated the formation of Ge nanocrystals with an average size estimated to be 5.4 nm. Raman scattering spectra showed a peak of the Ge-Ge vibrational mode downward shifted to 299.4 cm⁻¹, which was caused by quantum confinement of phonons in the Ge nanocrystals. Transmission electron microscopy (TEM) revealed that Ge nanocrystals were confined in (Ge + SiO₂) layers. This superlattice approach significantly improved both the size uniformity of Ge nanocrystals and their uniformity of spacing on the ‘Z’ growth direction.     

Preparation of five-layered Si/SixGe1−x nano-films by RF helicon magnetron sputtering

Five-layered Si/Si_xGe_1−x films on Si(1 0 0) substrate with single-layer thickness of 30 nm, 10 nm and 5 nm, respectively were prepared by RF helicon magnetron sputtering with dual targets of Si and Ge to investigate the feasibility of an industrial fabrication method on multi-stacked superlattice structure for thin-film thermoelectric applications. The fine periodic structure is confirmed in the samples except for the case of 5 nm in single-layer thickness. Fine crystalline Si_xGe_1−x layer is obtained from 700 °C in substrate temperature, while higher than 700 °C is required for Si good layer. The composition ratio (x) in Si_xGe_1−x is varied depending on the applied power to Si and Ge targets. Typical power ratio to obtain x = 0.83 was 7:3, Hall coefficient, p-type carrier concentration, sheet carrier concentration and mobility measured for the sample composed of five layers of Si (10 nm)/Si_0.82Ge_0.18 (10 nm) are 2.55 × 10⁶ /°C, 2.56 × 10¹² cm⁻³, 1.28 × 10⁷ cm⁻², and 15.8 cm⁻²/(V s), respectively.     

Femtosecond pulsed laser deposition of nanostructured TiO2 films

Nanostructured deposits of TiO₂ were grown on Si (1 0 0) substrates by laser ablating a TiO₂ sintered target in vacuum or in oxygen using a Ti:sapphire laser delivering 80 fs pulses. The effect of the laser irradiation wavelength on the obtained nanostructures, was investigated using 800, 400 and 266 nm at different substrate temperatures and pressures of oxygen. The composition of the deposits was characterized using X-ray photoelectron spectroscopy (XPS) and the surface morphology was studied by environmental scanning electron microscopy (ESEM) and atomic force microscopy (AFM). Deposits are absent of microscopic droplets in all conditions explored. The best deposits, constituted by nanoparticles of an average diameter of 30 nm with a narrow size distribution, were obtained at the shorter laser wavelength of 266 nm under vacuum at substrate room temperature.     

X-ray and AFM studies of polydisperse TiO2 (anatase) particles

Titanium dioxide (TiO₂) materials of a high chemical purity, as-prepared by the thermal hydrolysis, as well as subsequently modified by adsorption of different metal cations (Fe³⁺, Co²⁺, Cu²⁺), have been investigated by the X-ray diffraction, X-ray fluorescence and AFM microscopy methods. All TiO₂ powders have a fine-dispersated anatase structure and consist of grown together nanocrystallites of ∼8-17 nm. TiO₂ particles, usually ranging from 100 to 600 nm, show the ability to form large agglomerates, up to 2 μm in size. Contrary to the pure anatase, metal-modified TiO₂ particles possess a positive charge on their surface and can be lifted away by the AFM tip from the substrate surface during the scanning. This effect is mostly pronounced for the Fe-modified TiO₂ sample, where particles up to 250 nm are removed. The possible interaction mechanisms between different TiO₂ particles and the silicon tip are discussed. The electrostatic force has been found to play an essential role in the sample-tip interaction processes, and its value depends on the type of metal cation used.     

X-ray multiple diffraction in the characterization of TiNO and TiO2 thin films grown on Si(0 0 1)

TiO₂ and TiN_xO_y thin films grown by low pressure metal-organic chemical vapor deposition (LP-MOCVD) on top of Si(0 0 1) substrate were characterized by X-ray multiple diffraction. X-ray reflectivity analysis of TiO₂[1 1 0] and TiNO[1 0 0] polycrystalline layers allowed to determine the growth rate (−80 Å/min) of TiO₂ and (−40 Å/min) of TiNO films. X-ray multiple diffraction through the Renninger scans, i.e., ?-scans for (0 0 2)Si substrate primary reflection is used as a non-conventional method to obtain the substrate lattice parameter distortion due to the thin film conventional deposition, from where the information on film strain type is obtained.     

Polarized neutron reflectometry of the influence of Fe/Si,Fe/FeSi2 and Au/Fe interfaces on the magnetic properties of epitaxial Fe films

The magnetic and structural properties of epitaxial Fe films grown on Si(1 1 1) are investigated by polarized neutron reflectometry (PNR) at room temperature. The influence of different types of interfaces, Fe/Si, Fe/FeSi₂ and Au/Fe on the magnetic properties of Fe films deposited by molecular beam epitaxy onto Si(1 1 1) are characterized. We observe a drastic reduction of the magnetic moment in the entire Fe film deposited directly on the silicon substrate essentially due to strong Si interdiffusion throughout the whole Fe layer thickness. The use of a silicide FeSi₂ template layer stops the interdiffusion and the value of the magnetic moment of the deposited Fe layer is close to its bulk value. We also evidence the asymmetric nature of the interfaces, Si/Fe and Fe/Si interfaces are magnetically very different. Finally, we show that the use of Au leads to an enhancement of the magnetization at the interface.