Effectiveness of T-shaped acoustic resonators in low-frequency sound transmission control of a finite double-panel partition

Double-panel partitions are widely used for sound insulation purposes. Their insulation efficiency is, however, deteriorated at low frequencies due to the structural and acoustic resonances. To tackle this problem, this paper proposes the use of long T-shaped acoustic resonators in a double-panel partition embedded along the edges. In order to facilitate the design and assess the performance of the structure, a general vibro-acoustic model, characterizing the interaction between the panels, air cavity, and integrated acoustic resonators, is developed. The effectiveness of the technique as well as the optimal locations of the acoustic resonators is examined at various frequencies where the system exhibits different coupling characteristics. The measured optimal locations are also compared with the predicted ones to verify the developed theory. Finally, the performance of the acoustic resonators in broadband sound transmission control is demonstrated.     

QCM based sensor for detecting volumetric properties of liquids

We introduce a microacoustic sensor, which combines the quartz crystal microbalance, a liquid-filled cavity and an intermediate artificial layer with effective acoustic properties. Each of the three components fulfils a specific task. The quartz vibrates in its thickness shear mode and acts as source and detector of shear waves, which penetrate the intermediate artificial layer and excite a resonance in the liquid-filled cavity. Both the piezoelectric transducer and the liquid-filled cavity are high-Q resonators with well-adjusted resonance frequencies very close to each other. The intermediate artificial layer couples the two resonators in a distinct manner via control of the propagation of acoustic waves between the quartz crystal and the liquid-filled cavity layer. The origin of the sensor signal is a change of the resonance frequency of the liquid-filled cavity caused by variations of acoustic properties of the liquid analyte inside the cavity, first of all speed of sound. This resonance appears as second resonance peak in the admittance spectrum of the quartz crystal.     

A new model for film bulk acoustic wave resonators

Based on cavity resonance and sandwich composite plate （3D） theoretical model for frequency dispersion characterization theory, this paper presents a universal three-dimensional and displacement profile shapes of the film bulk acoustic resonator （FBARs）. This model provides results of FBAR excited thickness-extensional and flexure modes, and the result of frequency dispersion is proposed in which the thicknesses and impedance of the electrodes and the piezoelectric material are taken into consideration; its further simplification shows good agreement with the modified Butterworth-Van-Dyke （MBVD） model. The displacement profile reflects the vibration stress distribution of electrode shapes and the lateral resonance effect, which depends on the axis ratio of the electrode shapes a/b. The results are consistent with the 3D finite element method modeling and laser interferometry measurement in general.     

Reduction of sound transmission into a circular cylindrical shell using distributed vibration absorbers and Helmholtz resonators

A modal expansion method is used to model a cylindrical enclosure excited by an external plane wave. A set of distributed vibration absorbers (DVAs) and Helmholtz resonators (HRs) are applied to the structure to control the interior acoustic levels. Using an impedance matching method, the structure, the acoustic cavity, and the noise reduction devices are fully coupled to yield an analytical formulation of the structural kinetic energy and acoustic potential energy of a treated cylindrical cavity. Lightweight DVAs and small HRs tuned to the natural frequencies of the targeted structural and acoustic modes, respectively, result in significant acoustic and structural attenuation when the devices are optimally damped. Simulations show that significant interior noise reduction can only be achieved by adding damping to both structural and acoustic modes, which are resonant in the frequency bandwidth of interest. In order to be independent of the azimuth angle of the excitation and to avoid unwanted modal interactions, the devices are distributed evenly around the cylinder in rings. This treatment can only achieve good performance if the structure and the acoustic cavity are lightly damped.     

Propagation of acoustic waves in a fluid-filled pipe with periodic elastic Helmholtz resonators

Helmholtz resonators are widely used to reduce noise in a fluid-filled pipe system. It is a challenge to obtain lowfrequency and broadband attenuation with a small sized cavity. In this paper, the propagation of acoustic waves in a fluid-filled pipe system with periodic elastic Helmholtz resonators is studied theoretically. The resonance frequency and sound transmission loss of one unit are analyzed to validate the correctness of simplified acoustic impedance. The band structure of infinite periodic cells and sound transmission loss of finite periodic cells are calculated by the transfer matrix method and finite element software. The effects of several parameters on band gap and sound transmission loss are probed.Further, the negative bulk modulus of periodic cells with elastic Helmholtz resonators is analyzed. Numerical results show that the acoustic propagation properties in the periodic pipe, such as low frequency, broadband sound transmission, can be improved.     

Noise control in enclosures: modeling and experiments with T-shaped acoustic resonators

This paper presents a theoretical and experimental study of noise control in enclosures using a T-shaped acoustic resonator array. A general model with multiple resonators is developed to predict the acoustic performance of small resonators placed in an acoustic enclosure. Analytical solutions for the sound pressure inside the enclosure and the volume velocity source strength out of the resonator aperture are derived when a single resonator is installed, which provides insight into the physics of acoustic interaction between the enclosure and the resonator. Based on the understanding of the coupling between the individual resonators and enclosure modes, both targeted and nontargeted, a sequential design methodology is proposed for noise control in the enclosure using an array of acoustic resonators. Design examples are given to illustrate the control performance at a specific or at several resonance peaks within a frequency band of interest. Experiments are conducted to systematically validate the theory and the design method. The agreement between the theoretical and experimental results shows that, with the help of the presented theory and design methodology, either single or multiple resonance peaks of the enclosure can be successfully controlled using an optimally located acoustic resonator array.     

弯曲圆盘驱动的双Helmholtz共振腔换能器

使用双面同相振动的弯曲圆盘换能器驱动双Helmholtz共振腔,既放大了弯曲圆盘换能器弯曲共振频率以下频段的声输出,又利用两个Helmholtz共振腔的同相声源辐射模型实现了在Helmholtz共振频率处的"∞"字形垂直指向性,实现了低频指向性声发射。阐述了换能器实现"∞"字形低频指向性发射的机理,研究了腔体长度、金属圆片厚度及弯曲圆盘边缘简支厚度等关键结构参数对Helmholtz共振频率的影响,求解了换能器的发送电压响应、指向性等参数。依据仿真结果制作了实验样机,在消声水池中进行了电声性能测试。测试结果显示,指向性形状及液腔共振频率与仿真结果基本相符。这种由弯曲圆盘驱动的双Helmholtz共振腔水声换能器为实现水声换能器小尺寸、低频指向性发射提供了一种技术手段。      

水下圆柱形Helmholtz共振器的声学特性分析

理论分析了水下圆柱形Helmholtz共振器的声学特性. 综合考虑壁面弹性和辐射阻抗的影响,基于电-声类比的基本原理,建立了较为完善的水下圆柱形Helmholtz共振器的低频集中参量模型. 利用电路分析的基本方法,得到了系统的输入阻抗和声压传递函数表达式. 仿真分析了主要结构参数对共振器声学特性的影响,得出了一些有意义的结论. 在充水驻波罐中对自制的Helmholtz共振器进行了测量,并对实验结果进行了详细地误差分析. 去除压电水听器对测量结果的影响后,实验与仿真结果基本一致,从而验证了理论分析的正确性. 关键词： Helmholtz共振器 共振频率 传递函数 辐射阻抗     

On optimal design of half-wave resonators for acoustic damping in an enclosure

Acoustic design parameters of a half-wave resonator are studied experimentally for purely acoustic tuning of the resonator. According to the standard acoustic-test procedures, acoustic-pressure signals in the model enclosure with the resonators are measured. Based on the signals, quantitative acoustic properties of damping factor and sound absorption coefficient are evaluated and thereby, the acoustic-damping capacity of the resonator is characterized. Sound absorption coefficient has the advantages of the damping factor in various aspects. The coefficient indicates clearly the tuning frequency of the resonator, absorption effectiveness as a function of frequency, and overall damping capacity. The diameter and the number of a half-wave resonator, its distribution, and the blockage ratio at its inlet are selected as design parameters for optimal tuning of the resonator in the model enclosure. The resonators with larger diameter have the advantage of those with smaller one with respect to purely acoustic damping at the tuning frequency. The optimum number of resonators or the optimum open-area ratio decreases as boundary absorption decreases. When the open-area ratio exceeds the optimum value, over-damping appears, leading to a decrease in peak absorption coefficient and a broadening of absorption bandwidth. Blockage at the resonator inlet controls both peak absorption coefficient and its absorption bandwidth and it can be considered one of design factors for acoustic tuning.     

液体火箭发动机中声腔抑制不稳定燃烧的声学分析

发展了声腔的分析和数值模型,对液体火箭发动机不稳定燃烧的抑制作用进行了评定,通过迭代计算研究了二维流动和温度分布变化对声腔调 谐和稳定性能的影响,对不同的声腔几何尺寸和温度梯度的稳定性计算结果表明,燃烧带有较大开口面积的声腔会更大程度地改变振荡的空间分布,这种改变而且影响了驱动和抑制燃烧的机理,讨论了在声腔设计安排中正确选择声腔的几何尺寸,且比较了不同长度和不同直径声腔的阻尼特性,通过考察声吸收系统的方法来最优化系统的阻尼,得到了可供设计参考的结论。     

Development of two-port surface acoustic wave resonator with Al/Au electrodes for gas sensing

Simple and efficient surface acoustic wave(SAW)two-port resonators with low insertion loss and high Q-values on ST-X quartz substrate using a corrosion-proof A1/Au-stripe electrode structure are developed for gas sensing.It was composed of two shorted grating reflectors and adjacent intedigital transducers(IDT),and an active metal film in the cavity between the IDTs for the sensitive film coating.The devices are expected to provide good protection towards metal electrode for gas sensors application in chemically reactive environments.Excellent device performance as low insertion loss,high Q factor and single-mode are achieved by carefully selecting the metallic electrode thickness,cavity length and acoustic aperture.Prior to fabrication,the coupling of modes(COM)model was performed for device simulation to determine the optimal design parameters.The fabricated single-mode SAW resonator at operation frequency of 300 MHz range exhibits matched insertion loss of~6.5 dB and loaded Q factor in the 3000 range.Using the fabricated resonator as the feedback element,a dualresonator-oscillator with excellent frequency stability(0.1 ppm)was developed and evaluated experimentally,and it is significant for performance improvement of SAW gas sensor.     

应用于气体传感器的具有铝/金电极的单模式两端对声表面波谐振器

为改善气体传感器性能,通过器件优化设计获得了一种应用于气体传感器的具有低损耗、高品质因子(Q)的单模式两端对声表面波(SAW)谐振器。该谐振器由两个换能器、分置于换能器两边的短路栅反射器以及在换能器之间分布的用于敏感膜镀膜的约2.5mm金属薄层构成。谐振器采用铝/金双层电极以降低测试气体环境的腐蚀影响。利用经典耦合模(COM)理论对器件性能进行了仿真以提取优化的结构设计参数。基于仿真结果,实验研制了基于300MHz频率的新型铝/金电极SAW两端对谐振器,测试结果显示所研制器件具有较低损耗(〈7dB),较高Q值(-3000)以及单一谐振模式的特点,并且,以所研制的新型谐振器为频率控制单元的谐振器型振荡器表现出良好的频率稳定度(t15Hz/h),这对于改善气体传感器的检测下限及稳定性等性能指标具有重要意义。      

Experimental and computational investigation of coupled resonator–cavity systems

Launch vehicle noise is broadband in nature and the noise transmitted into the payload fairing is reduced by treating its interior with an acoustic absorption layer. The latest generation payload fairings are made from composite material which offer poor noise attenuation at low frequencies. One possible solution for reducing the low frequency noise is to use Helmholtz resonators tuned to a few of the dominant low frequency components, such as shell ring frequency or the first few cavity modes of the fairing. The paper presents a simplified modelling approach for numerical simulation of a coupled cavity–resonator system which is validated by experiments. The influence of damping and resonator volume fraction on the coupled system performance, to suppress the first axial mode in a cylindrical cavity, is shown and the resonator volume fraction required for significantly (more than 5 dB) suppressing the cavity axial mode is established.     

谐振式检测器谐振腔对声表面波气相色谱仪灵敏度的影响

研究了谐振式检测器谐振腔对声表面波气相色谱仪灵敏度的影响。构建无液膜负载和有液膜负载下压电基片和金属指条结构的三维有限元模型,利用有限元方法提取不同周期结构的耦合模参量,结合P矩阵级联技术,推导出传感器灵敏度随检测器腔体结构改变的变化关系。实验制备了两种三换能器结构的声表面波谐振器,其输入换能器与输出换能器间距离分别为22.25倍波长和1.25倍波长,通过测试甲基膦酸二甲酯气体,验证理论计算结果。结果表明:缩短谐振器的谐振腔长度使器件中心处能量更为集中,有效地提高了声表面波气相色谱仪灵敏度。      

腔壁弹性对水下小型圆柱形亥姆霍兹共振器共振频率的影响

理论和实验研究了腔壁弹性对水下小型圆柱形亥姆霍兹共振器共振频率的影响.基于电-声类比理论,建立了小型共振器的简化模型,利用电路分析方法得到了便于计算的共振频率一般表达式.分别仿真分析了共振器壁面厚度和材料对共振频率的影响,得到了不同尺寸的小型共振器的近似刚性条件.在充水驻波罐中对不同壁厚、不同材料的小型圆柱形亥姆霍兹共振器的共振频率进行了测量,实验结果较好地验证了理论分析和近似刚性条件的正确性.所得结果对小型圆柱形亥姆霍兹共振器的设计和水下应用具有较好的参考价值. 关键词： 亥姆霍兹共振器 共振频率 传递函数 辐射阻抗     

ANALYSIS OF THE PERIODIC PRESSURE FLUCTUATIONS INDUCED BY FLOW OVER A CAVITY

Subsonic flows over Helmholtz resonators often cause strong periodic pressure fluctuations inside the resonators over a range of outer flow velocities. The flow-excitation mechanism is known to be governed by both the shedding of discrete vortices within the shear layer over the orifice and the acoustic response of the cavity. This self-sustained oscillation phenomenon is often analyzed by using a feedback loop model where the flow excitation and the acoustic response of the resonator are approximately modelled as a forward gain function and as a backward gain function respectively. In the present work, a similar approach was followed and a new forward gain function was derived based on the concept of “vortex sound” to model the flow excitation. The formulation combined this forward gain function with a backward gain function from previous work, within the framework of the feedback loop analysis. The approximate method allowed the frequency and the relative amplitude of the cavity pressure fluctuations to be predicted for a range of flow velocities. In addition, the extended Nyquist stability criterion was used to estimate the onset and the termination velocities of the first two modes of the shear layer flow oscillations. Experimental data were obtained using a rigid-walled cavity in a low-speed wind tunnel. The results showed that the model predictions were in reasonably good agreement with the experimental data.     

声腔对电动式换能器工作特性的影响

传统的电动式换能器设计理论中,未考虑压力补偿系统等声腔结构对声学性能的影响,声源级理论设计结果与实测结果存在较大差别.研究中将电动式换能器内部的三段气腔视为突变截面声腔结构,给出了声腔的四端网络等效电路,将其作为辐射面的负载添加到电动式换能器的传统等效电路中,获得了电动式换能器改进的等效电路.基于改进的等效电路求解了带...     

A novel matching network employing surface acoustic wave devices for W-CDMA power amplifiers

This paper describes a new approach of designing high Q surface acoustic wave (SAW) resonators as an inductive element in the matching network for W-CDMA power amplifiers (PAs). Spiral inductors based on CMOS/BiCMOS technologies presently possess relatively low Q (typically <10) and occupy a considerably large area. In order to break through the limitations of the spiral inductors, the authors attempt to apply higher Q and wideband SAW resonators employing Cu-grating/15 degrees YX-LiNbO(3)-substrate structure to the matching network for improved PA performance. An analysis was made on SAW resonators in detail, and an SAW resonator having a very small capacitance ratio of 3.28 and moderate Q of 147.8 was developed. After discussing the frequency dependence of the effective inductances, SAW resonators, which are used to be as inductive elements in the matching networks of PAs, were designed and fabricated. The PA including the matching circuit was simulated using the characteristics of the fabricated SAW resonators. The result showed that with better shape factor and good out-of-rejection, the SAW resonators definitely work as an inductive element and could replace widely used spiral inductors.     

Helmholtz水声换能器弹性壁液腔谐振频率研究

针对传统Helmholtz水声换能器设计中刚性壁假设的局限性,将Helmholtz腔体的弹性计入到液腔谐振频率计算中,实现低频弹性Helmholtz水声换能器液腔谐振频率精确设计.基于细长圆柱壳腔体的低频集中参数模型,导出了腔体弹性引入的附加声阻抗表达式,得到了弹性壁条件下Helmholtz水声换能器等效电路图,给出了考虑了末端修正的弹性壁Helmholtz共振腔液腔谐振频率计算公式.利用ANSYS软件建立了算例模型,仿真分析了不同材质、半径、长度时的Helmholtz共振腔液腔谐振频率.结果对比表明弹性理论值与仿真值符合得很好,相比起传统的刚性壁理论计算结果,本文的弹性壁理论得出的液腔谐振频率值有所降低,与真实情况更加接近.本文的结论可以为精确设计低频弹性Helmholtz水声换能器提供理论支持.     

Broadband acoustic focusing by symmetric Airy beams with phased arrays comprised of different numbers of cavity structures

We realize broadband acoustic focusing effect by employing two symmetric Airy beams generated from phased arrays,in which the units of the phased arrays consist of different numbers of cavity structures, each of which is composed of a square cavity and two inclined channels in air. The exotic phenomenon arises from the energy overlapping of the two symmetric Airy beams. Besides, we demonstrate the focusing performance with high self-healing property, and discuss the effects of structure parameters on focusing performance, and present the characteristics of the cavity structure with straight channels. Compared with other acoustic lenses, the proposed acoustic lens has advantages of broad bandwidth(about 1.4 kHz), high self-healing property of focusing performance, and free adjustment of focal length. Our finding should have great potential applications in ultrasound imaging and medical diagnosis.