Effect of nitrogen partial pressure on Al–Ti–N films deposited by arc ion plating

AlTiN films with different nitrogen partial pressures were deposited using arc ion plating (AIP) technique. In this study, we systematically investigated the effect of the nitrogen partial pressure on composition, deposition efficiency, microstructure, macroparticles (MPs), hardness and adhesion strength of the AlTiN films. The results showed that with increasing the nitrogen partial pressure, the deposition rate exhibited a maximum at 1.2 Pa. Results of X-ray photoelectron spectroscopy (XPS) analysis revealed that AlTiN films were comprised of Ti–N and Al–N bonds. XRD results showed that the films exhibited a (1 1 1) preferred growth, and AlTi₃N and TiAl_x phases were observed in the film deposited at 1.7 Pa. Analysis of MPs statistics showed MPs decreased with the increase in the nitrogen partial pressure. In addition, the film deposited at 1.2 Pa possessed the maximum hardness of 38 GPa and the better adhesion strength.     

Comparative study on structural and optical properties of ZnO thin films prepared by PLD using ZnO powder target and ceramic target

Zinc oxide thin films have been obtained in O₂ ambient at a pressure of 1.3 Pa by pulsed laser deposition (PLD) using ZnO powder target and ceramic target. The effect of temperature on structural and optical properties of ZnO thin films was investigated systematically by XRD, SEM, FTIR and PL spectra. The results show that the best structural and optical properties can be achieved for ZnO thin film fabricated at 700 °C using powder target and at 400 °C using ceramic target, respectively. The PL spectrum reveals that the efficiency of UV emission of ZnO thin film fabricated by using powder target is low, and the defect emission of ZnO thin film derived from Zn_i and O_i is high.     

Electrochemical evaluation of Ta2O5 thin film for all-solid-state switchable mirror glass

We investigated the electrochemical property of Ta₂O₅ thin film for all-solid-state switchable mirror glass. The film was deposited by reactive dc magnetron sputtering in a mixture gas of argon and oxygen. The current density of the film covered WO₃/ITO/glass was decreased with decreasing argon/oxygen ratio and working pressure measured by cyclic voltammetry. The film deposited at argon/oxygen ratio of 4.7 and working pressure of 1.0 Pa had better electrochemical property than that of other deposition condition. Its estimated proton conductivity was 2.1 × 10^? 9 S/cm by conventional ac impedance method. However, the device using the film showed poor optical switching property. The transmittance change of the device at a wavelength of 670 nm was only 16% by applying voltage. On the other hand, the device using the film deposited at working pressure of 0.7 Pa was able to switch its optical switching property from reflective of 0.1% to transparent states of 44% within 15 s. These results indicate that the suitable deposition condition of the Ta₂O₅ thin film existed to be used for all-solid-state switchable mirror glass.     

Factors affecting the electro-optical and structural characteristics of nano crystalline Cu doped (Cd–Zn)S films

This work investigates the effects of the temperature, deposition time and annealing ambient on the electro-optical and structural properties of nano crystalline (Cd–Zn)S films prepared by chemical bath deposition (CBD). The deposited films being uniform and adherent to the glass substrates are amorphous in nature and the crystallinity as well as the grain size is found to increase on post-deposition annealing. The obtained specimens are thoroughly characterized before and after annealing paying particular attention to their structure, composition and morphology. Annealing in air reduces the extent of disorder in grain boundaries and energy band-gap. A correlation between the structural and optical properties is investigated in detail. The surface morphology and structural properties of the as-deposited and annealed (Cd–Zn)S thin films are studied using X-ray diffraction (XRD), scanning electron microscope (SEM) and optical transmission spectra. The optical transmission spectra are recorded within the range of 300–800 nm and 300–900 nm. The electroluminescent (EL) intensity is found to be maximum at a particular temperature, which decreases with further increase in temperature and peaks of photoluminescent (PL) and EL spectra are centered at 546 nm and 592 nm. The emission intensity also increases with increasing thickness of the film.     

Absorption spectra response of XRQA radiochromic film to x-ray radiation

Gafchromic XRQA, radiochromic film is a high sensitivity auto developing x-ray analysis films designed and available for kilovoltage x-ray, dose and QA assessment applications. The film is designed for reflective analysis with a yellow transparent top filter and white opaque backing materials. This allows the film to be visually inspected for colour changes with a higher level of contrast than clear coated radiochromic films such as Gafchromic EBT version 1. The spectral absorption properties in the visible wavelengths have been investigated and results show two main peaks in absorption located at 636 nm and 585 nm. These peaks are located in the same position as EBT Gafchromic film highlighting a similar chemical monomer/polymer for radiation sensitivity. A much higher sensitivity however is found at kilovoltage energies with an average 1.55 OD units per 20 cGy irradiation variation measured at 636 nm using 150 kVp x-rays. This is compared to approximately 0.12 OD units per 20 cGy measured at 636 nm for EBT film at 6 MV x-ray energy. That is, the XRQA film is more than 10 times more sensitive than EBT1 film. The visual colour change is enhanced by the yellow polyester coating. However this does not affect the absorption spectra properties in the red region of analysis which is the main area for use using desktop scanners in reflection mode.     

Exciton-polariton state in nanocrystalline SiC films

We studied the features of optical absorption in the films of nanocrystalline SiC (nc-SiC) obtained on the sapphire substrates by the method of direct ion deposition. The optical absorption spectra of the films with a thickness less than ~500 nm contain a maximum which position and intensity depend on the structure and thickness of the nc-SiC films. The most intense peak at 2.36 eV is observed in the nc-SiC film with predominant 3C-SiC polytype structure and a thickness of 392 nm. Proposed is a resonance absorption model based on excitation of exciton polaritons in a microcavity. In the latter, under the conditions of resonance, there occurs strong interaction between photon modes of light with λ_ph=521 nm and exciton of the 3С polytype with an excitation energy of 2.36 eV that results in the formation of polariton. A mismatch of the frequencies of photon modes of the cavity and exciton explains the dependence of the maximum of the optical absorption on the film thickness.     

Influence of growth temperature and deposition duration on the structure,surface morphology and optical properties of InN/YSZ (1 0 0)

InN films with the wurtzite structure have been grown directly on YSZ (1 0 0) substrate by the RF-magnetron sputtering technique. Strongly (0 0 2) oriented films with smooth surfaces (0.7–2.9 nm surface roughness depending on substrate temperature), were grown within 30 min. Films deposited for 60 min developed three-dimensional (3D) pyramidal islands on top of their surfaces, which diminished the residual elastic strain. The optical absorption edge and PL peak energy around 1.7 eV were found to redshift with increasing film thickness and substrate temperature.     

The preparation and characterization of nanoparticle TiO2/Ti films and their photocatalytic activity

Nanoparticle TiO₂/Ti films were prepared by a sol–gel process using Ti(OBu)₄ as raw material, the as-prepared film samples were also characterized by TG-DTA, XRD, TEM, SEM, XPS, DRS, PL, SPS and EFISPS testing techniques. TiO₂ nanoparticles experienced two processes of phase transition, i.e. amorphous to anatase and anatase to rutile at the calcining temperature range from 450 to 700 °C. TiO₂ nanoparticles calcined at 600 °C had similar composition, structure, morphology and particle size with the internationally commercial P-25 TiO₂ particles. Thus, the conclusion that 600 °C might be the most appropriate calcining temperature during the preparation process of nanoparticle TiO₂/Ti film photocatalysts could be made by considering the main factors such as the properties of TiO₂ nanoparticles, the adhesion of nanoparticle TiO₂ film to Ti substrate, the effects of calcining temperature on Ti substrate and the surface characteristics and morphology of nanoparticle TiO₂/Ti film for the practice view. The Ti element mainly existed on the nanoparticle TiO₂/Ti(3) film calcined at 600 °C as the chemical state of Ti⁴⁺, while O element mainly existed as three kinds of chemical states, i.e. crystal lattice oxygen, hydroxyl oxygen and adsorbed oxygen with increasing band energy. Its photoluminescence (PL) spectra with a peak at about 380 nm could be observed using 260 nm excitation, possibly resulting from the electron transition from the bottom of conduction band to the top of valence band. The PL peak position was nearly the same as the onset of its diffuse reflection spectra (DRS) and surface photovoltage spectroscopy (SPS), demonstrating that the effects of the quantum size on optical property were greater than that of the Coulomb and surface polarization. The PL spectra with two peaks related to the anatase and rutile, respectively, could be observed using the excited wavelength of 310 nm. Weak PL spectra could be observed using the excited wavelength of 450 nm, resulting from surface states. In addition, during the experimental process of the photocatalytic degradation phenol, the photocatalytic activity of nanoparticle TiO₂/Ti film with three layers calcined at 600 °C was the highest.     

Acceptors related to group I elements in ZnO ceramics

ZnO ceramics doped with Li, Na or K were sintered in air for 4 h at 1000 °C. Electrical conductivity as well as photoluminescence (PL), PL excitation and photoconductivity spectra were measured and compared with those in undoped samples. The influence of both fast and slow cooling of the samples from 1000 °C on measured characteristics was investigated. The yellow–orange PL bands associated with the deep acceptors Li_Zn, Na_Zn and K_Zn were observed and the corresponding PL excitation spectra were determined. These acceptors were found to form some complexes with other lattice defects.     

Growth of SnO2 nanoparticles via thermal evaporation method

Tin oxide (SnO₂) nanoparticles were fabricated by evaporation of Sn powers at 1000 °C in air pressure. The as-deposited SnO₂ particles were single crystal structure, which were mostly spherical shape, the diameter of particles was ranging from 200 to 600 nm. The photoluminescence (PL) spectrum showed that a sharp emission peak at around 393 nm with the excitation wavelength at 325 nm, which suggested possible applications in nanoscaled optoelectronic devices. It was also found that the holding time affects the morphology of the products. The formation mechanism of SnO₂ particles was discussed.     

Transition of magnetic anisotropy in Ni/GaAs (0 0 1) observed by magnetization and ferromagnetic resonance

Polycrystalline thin Ni films deposited onto GaAs (0 0 1) show a transition of the magnetic anisotropy depending on its thickness. The anisotropy is perpendicular to the film plane for the thicknesses of the film ⩽12 nm. This becomes in-plane in the films having thicknesses ⩾15 nm. The films are deposited onto the n-type GaAs (0 0 1) substrate by the usual thermal evaporation method and also by the electron beam evaporation in ultra high vacuum onto a GaAs epilayer in the standard molecular beam epitaxy system. The magnetization and ferromagnetic resonance (FMR) are observed in the temperature range from 4.2 to 300 K. For the discussion of the microscopic origin of the anomalous properties in magnetization and FMR experiments, the experimental results are reviewed by introducing a uniaxial anisotropy, which is calculated from the easy-axis and hard-axis magnetization data. This calculated anisotropy is able to explain the temperature and angle dependency of the FMR spectra of the Ni films. Hence the magnetization and FMR spectra are in agreement with the type of the anisotropy and its temperature dependency. In addition to these, the temperature dependence of the in-plane magnetic anisotropy is able to explain the previously reported anomalous effect of reducing the squareness at low temperatures in Ni/GaAs.     

Photoluminescence due to exciton–exciton scattering in a GaAs/AlAs multiple quantum well

We have investigated photoluminescence (PL) properties of a GaAs (20 nm)/AlAs (20 nm) multiple quantum well at 10 K under intense excitation conditions. It has been found that a PL band due to exciton–exciton scattering, the so-called P emission, is observed in addition to the biexciton PL under an excitation energy higher than the fundamental heavy-hole exciton by the energy of the longitudinal optical phonon. On the other hand, the P band could never be observed at an excitation energy much higher than the exciton energy, where a band-filling phenomenon appears in the PL spectrum. Furthermore, we confirmed the existence of optical gain leading to stimulated emission in the energy region of the P band using a variable-stripe-length method.     

Luminescence properties of co-doped ZnS:Ni,Mn and ZnS:Cu,Cd nanoparticles

Transition metal doped ZnS:Ni and ZnS:Cu and co-doped ZnS:Ni, Mn and ZnS:Cu, Cd nanoparticles were synthesized through the chemical precipitation method in an air atmosphere. The XRD analysis of co-doped samples shows the formation of cubic phase. The average size of nanoparticles ranges from 3.6 to 5.5 nm. The formation of co-doped nanoparticles was confirmed by XRD and PL analysis. The PL spectra show that the obtained nanoparticles have good crystal quality. An optimum concentration of transition metals was selected in co-doped ZnS nanoparticles.     

Emission characteristics of SPAN-80 activated ZnS nanocolloids

Quantum surface effects (new emission bands, blueshifts, intensity enhancement) were observed in SPAN-80 activated ZnS nanocolloids and explained in terms of time-dependent density functional theory. The experimental evidences were demonstrated for both undoped and Cu, Mn-doped colloidal phases. The photoluminescence spectra of these materials showed a new green band at 520 nm (ZnS:Cu) and a yellow-orange band at 576 nm (ZnS:Mn) besides a blue band at 465 nm. All bands lie in the visible region and are blueshifted, show sharp emissions with narrow widths and have approximately 20-times stronger intensities in comparison with those of the bulk samples. The time-resolved luminescence spectra showed that the life-times of free electrons were 0.12 μs and 1.9 ms in ZnS:Cu and ZnS:Mn correspondingly.     

Hydrogen permeation of tungsten phosphate glass thin films

Thin films of tungsten phosphate glasses were deposited on a Pd substrate by a pulsed laser deposition method and the flux of hydrogen passed thorough the glass film was measured with a conventional gas permeation technique in the temperature range 300–500 °C. The glass film deposited at low oxygen pressure was inappropriate for hydrogen permeation because of reduction of W ions due to oxygen deficiency. The membrane used in the hydrogen permeation experiment was a 3-layered membrane and consisted of Pd film (~ 20 nm), the glass film (≤ 300 nm) and the Pd substrate (250 µm). When the pressure difference of hydrogen and thickness of the glass layer were respectively 0.2 MPa and ~ 100 nm, the permeation rate through the membrane was 2.0 × 10^? 6 mol cm^? 2 s^? 1 at 500 °C. It was confirmed that the protonic and electronic mixed conducting glass thin film show high hydrogen permeation rate.     

Effect of thickness on the structural,optical and electrical properties of thermally evaporated PbI2 thin films

This work describes the physical properties of lead iodide (PbI₂) thin films with different thicknesses that were deposited on ultrasonically cleaned glass substrates using a thermal evaporation technique at 5×10^-6 torr. The initial material was purified by the zone refining technique under an atmosphere of argon gas. XRD analysis of the material demonstrates that the thin films were preferably oriented along the (001) direction. The size of the crystallites was calculated from the Scherer relation and found to be in the range of ～5–10 nm, with higher values being observed for increasing film thicknesses. The optical energy band gaps were evaluated and determined to belong to direct transitions. Because the band gap increased with decreasing film thickness, a systematic blue shift was observed. The surface morphologies of PbI₂ films exhibited a clear increase in grain size with increasing film thickness. The photoluminescence and dc conductivity of the thin films are also discussed.     

Photoluminescence characterization of beryllium-implanted 6H–silicon carbide

Beryllium has been implanted into both n- and p-type 6H–SiC with post-implantation annealing at 1600 °C. Photoluminescence (PL) measurements have been performed, and PL lines at 420.5, 431 nm, and a broad band at around 505 nm have been observed. The line at 420.5 nm is attributed to an intrinsic defect D_II-center induced by beryllium implantation. The effects of excitation intensity and temperature during the PL experiments are investigated. Based on the excitation laser dependence PL result, the new doublet lines at around 431 nm are thought to be associated with beryllium related bound excitons. The broad band corresponding to the green luminescence at room temperature has been attributed to the recombination of free carriers to beryllium bound levels.     

Re-charging the luminescence states in CdSe/ZnS quantum dots at the conjugation to Osteopontin antibodies

The paper presents the original study of photoluminescence (PL) and Raman scattering spectra of core–shell CdSe/ZnS quantum dots (QDs) covered by the amine-derivatized polyethylene glycol (PEG) with luminescence interface states. First commercially available CdSe/ZnS QDs with emission at 640 nm (1.94 eV) covered by PEG polymer have been studied in nonconjugated states. PL spectra of nonconjugated QDs are characterized by a superposition of PL bands related to exciton emission in a CdSe core and to the hot electron–hole recombination via high energy luminescence states. The study of high energy PL bands in QDs at different temperatures has shown that these PL bands are related to luminescence interface states at the CdSe/ZnS or ZnS/polymer interface. Then CdSe/ZnS QDs have been conjugated with biomolecules—the Osteopontin antibodies. It is revealed that the PL spectrum of bioconjugated QDs changed essentially with decreasing hot electron–hole recombination flow via luminescence interface states. It is shown that the QD bioconjugation process to Osteopontin antibodies is complex and includes the covalent and electrostatic interactions between them. The variation of PL spectra due to the bioconjugation is explained on the basis of electrostatic interaction between the QDs and biomolecule dipoles that stimulates re-charging QD interface states. The study of Raman scattering of bioconjugated CdSe/ZnS QDs has confirmed that the antibody molecules have the electric dipoles. It is shown that CdSe/ZnS QDs with luminescence interface states are promising for the study of bioconjugation effects with specific antibodies and can be a powerful technique in biology and medicine.     

Nonlinear optical properties of a series of azobenzene liquid-crystalline materials

The nonlinear optical properties of a series of azobenzene liquid-crystalline materials, which have different side-chain lengths in their molecular structure from one to another, were investigated using Z-scan method under picosecond pulse laser at 532 nm, 1064 nm and CW 488 nm excitation. The mechanism accounting for the process of nonlinear refraction was discussed under different laser excitations. The polymer films possess very large nonlinear refraction at all the three different laser excitations. Especially, the nonlinear refractive index becomes larger as the length of side-chain, where azobenzene group is contained, increases under pulse excitation at 1064 nm.     

Absorption,luminescence, and electron paramagnetic resonance of molybdenum ions in CdWO4

A single crystal of cadmium tungstate (CdWO₄) containing approximately 200 ppm of molybdenum was grown by the Czochralski method and then characterized in a series of optical absorption, photoluminescence (PL), photoluminescence excitation (PLE), and electron paramagnetic resonance (EPR) experiments. The Mo⁶⁺ ions substitute for W⁶⁺ ions and serve as recombination sites for electrons and holes when the crystal is exposed to ionizing radiation. A charge-transfer absorption band for the Mo⁶⁺ ions was observed near 320 nm at 10 K. The PL experiments, performed at low temperature with 325 nm excitation, showed a Mo-associated emission peaking near 680 nm. A direct correlation of the 680 nm emission and the 320 nm absorption band was established by the PLE data. When these doped CdWO₄ crystals are exposed at low temperature either to light that is near or above the band gap or to X-rays, the Mo⁶⁺ ions can trap an electron and form stable Mo⁵⁺ ions. The EPR spectrum of the Mo⁵⁺ ions was observed at temperatures near 15 K, and a complete set of parameters describing the g matrix was obtained from an angular dependence study.