水蒸气在垂直钛板表面的冷凝传热特性

对水蒸气在垂直钛板表面的冷凝传热特性进行了可视化实验研究。实验结果表明,蒸汽在钛表面为液滴和沟流状液膜共存的混合冷凝形式。随着表面过冷度的增大,滴状区所占的面积比η逐渐减小,且液滴的脱落直径逐渐增大,导致表面的冷凝传热系数随之下降。η值大于50%时,冷凝传热系数随滴状区所占面积比的减小而陡降,滴状区面积小于膜状区后,η值对冷凝表面传热性能的影响较小。     

含有不凝气体的蒸汽滴状冷凝传热实验研究

本文对饱和水蒸气和空气的混合物在垂直表面上滴状冷凝传热特性进行了实验研究。考察了不同的压力条件下不凝气对冷凝传热的影响。与膜状冷凝实验结果对比表明,滴状冷凝对含有不凝气的蒸汽冷凝传热有强化作用;在较高的冷凝压力下不凝气体对传热的影响相对较小。     

低压蒸汽滴状冷凝过程中液滴生长特性

研究了低压条件对滴状冷凝过程液滴生长特性的影响。首先,研究了超疏水表面上空气环境和蒸汽环境中附着液滴的接触角,发现蒸汽环境中的接触角比空气环境中的小,而蒸汽压力对接触角没有显著影响。第二,实验研究了冷凝过程中的液滴的生长周期和脱落尺寸,液滴的脱落半径随压力的降低而增大,生长周期也随之延长。第三,实验研究了液滴合并生长速率,并结合理论分析直接冷凝长大的生长速率,直接冷凝生长速率随压力的减小而减小,并随过冷度的减小而下降,而实验范围内合并生长速率不受压力影响。第四,根据滴状冷凝液滴分布的时间序列模型,分析了不同压力下液滴生长的临界尺寸,随着压力的降低,液滴生长方式的临界尺寸增大。     

聚四氟乙烯表面滴状冷凝的实验研究

根据递推法测定滴状冷凝传热系数原理,搭建了滴状冷凝传热系数测定试验台,并对聚四氟乙烯材料表面的传热特性进行了试验测定,分析了影响滴状冷凝传热系数的因素。     

蒸汽剪切驱动液滴行为的格子Boltzmann模拟

滴状冷凝过程中,存在蒸汽流动对液滴的吹扫作用,液滴在蒸汽剪切作用下克服壁面黏附变形和运动,液滴运动速度越大,冷凝传热性能越高。但是液滴在蒸汽作用下变形和运动的细节还不清晰,蒸汽速度对液滴变形和运动的影响机理还不明确。本文采用自由能格子Boltzmann方法研究了在不同蒸汽速度剪切作用下,液滴在具有不同润湿性固体表面上的变形和运动过程,分析了蒸汽速度和接触角对液滴变形和运动的影响机制,结果显示随着蒸汽速度的增加,液滴变形越大,液滴在固体表面的运动速度越大,停留时间越短,有利于液滴的移除和表面更新,相同蒸汽速度的作用下,液滴在接触角大的固体表面上变形和运动速度越大,也有利于液滴的移除和表面更新。从而定性或半定量地揭示了蒸汽速度影响蒸汽滴状冷凝传热的物理机制。     

滴状冷凝传热的多尺度规划与最佳接触角

滴状冷凝传热过程具有典型的多尺度特征,一方面体现于壁面上液滴尺寸分布的空间多尺度特征以及液滴生长过程的时间多尺度分布,另一方面体现于冷凝壁面物理化学特性以及液固相互作用特性的描述和量度上的多尺度特征.本文基于包含界面效应影响的滴状冷凝传热模型,分析了液滴尺寸分布的多尺度特征及其对滴状冷凝传热性能的影响,并通过分析液滴尺...     

电场下液滴合并自弹跳行为的分子动力学研究

在工程上通常利用滴状冷凝提高冷凝换热效率、进而强化传热。而当冷凝液滴发生合并自弹跳时,冷凝换热系数是传统滴状冷凝的1.3至1.5倍,因此液滴合并自弹跳现象对冷凝传热强化的贡献是非常大的。一些宏观实验和理论研究表明,加入外电场能进一步促进冷凝液滴合并自弹跳的频率和高度,但在纳米尺度下是否仍遵守这一规律还未可知,因此本文使用分子动力学模拟方法,探究了在超疏水表面上电场的方向和强度对纳米纯水液滴合并自弹跳行为的影响,模拟结果表明垂直向上方向电场会抑制液滴合并自弹跳,垂直向下方向存在一个电场促进弹跳的区间,在此区间内电场强度越大,弹跳速度越大.     

超疏水-疏水组合表面蒸汽冷凝的实验研究

液滴的快速脱落和移除对蒸汽滴状冷凝传热具有重要的影响,超疏水表面由丁二具有接触角大,接触角滞后小的优点而用于驱动冷凝液滴的自发运动,但是,常压蒸汽在超疏水表面冷凝时,液滴的润湿形态还没有定论。本文设计了超疏水疏水条纹间隔排列的超疏水一疏水组合表面,研究了常压蒸汽在组合表面上的冷凝过程,观测了液滴的运动特性,测量了超疏水一疏水组合表面上常压蒸汽冷凝传热性能。实验结果显示疏水区液滴在表面张力差的作用下从疏水区向超疏水区自发迁移,说明超疏水区液滴处于Wenzel润湿形态,超疏水一疏水组合表面蒸汽冷凝传热性能比完全超疏水和完全疏水表面传热性能的面积加权平均值大。说明液滴的自发迁移运动强化了疏水区的传热性能。     

蒸汽滴状冷凝液滴表面温度分布及演化

利用红外热成像技术研究了蒸汽滴状冷凝中液滴合并过程表面温度分布及演化机制,并基于此分析了不同尺寸液滴表面温度随传热通量变化的分布规律。实验结果表明:与蒸汽在微小液滴表面发生连续冷凝不同,液滴合并过程中蒸汽通过四个阶段实现在大液滴表面的周期性冷凝传热;其中,在液滴吸收蒸汽冷凝放热阶段和向壁面传热阶段之间存在一个平衡,高热通量时,蒸汽向液滴表面传热过程占主导,液滴表面温度随尺寸增加而升高;低热通量时,液滴向冷凝壁面传热过程占主导,液滴表面温度随尺寸增加而降低。液滴运动引起的蒸汽在大液滴表面直接冷凝过程为强化低压蒸汽冷凝传热提供了新思路。     

分子自组装膜表面滴膜共存冷凝传热的研究

本文以不同处理工艺制备十八烷基硫醇自组装膜,研究制备的表面上蒸气冷凝传热过程.结果表明不同的成膜温度,可以实现膜表面上水蒸气冷凝形态从膜状到滴状的过渡.并研究了该表面上滴膜共存状态下的冷凝传热特性,表明过渡状冷凝传热随固液自由能差渐进变化的实质是冷凝形态的渐进变化,表面上冷凝液运动形态的不同也将导致传热性能的改变,并对自组装膜表面上的冷凝传热系数可能随操作时间的增加而回升的现象进行了分析.     

滴状冷凝过程液滴自由表面温度场分析

对于滴状冷凝过程及其传热强化机理, 一般通过分析冷凝壁面上液滴分布和运动规律进行研究, 并且将单个液滴视为稳定的个体, 很少涉及液滴内部运动特征. 本文通过红外热像仪观测了纯蒸气滴状冷凝过程中, 液滴运动时自由表面温度场的演化过程. 发现在疏水壁面上, 液滴由于合并或脱落而发生移动过程中, 其自由表面温度先降低, 而后升高并高于移动前温度. 通过分析疏水表面上液滴移动过程的物理模型, 认为液滴移动时表面液膜发生履带式滚动现象, 或者发生液滴内部与自由表面附近的液体间形成对流和掺混现象. 对液滴运动时表面温度演变规律的分析表明: 触发液滴表面发生持续冷凝可能需要克服一个临界过冷度, 当气液间温差超过该临界值时才诱发冷凝; 液滴合并或脱落等整体运动过程, 导致了液滴内部的运动特征, 并促进了较大尺寸液滴表面发生直接冷凝, 这为强化冷凝传热的研究提供新的思路.     

CONDENSATION HEAT TRANSFER OF STEAM ON VERTICAL DROPWISE AND FILMWISE COEXISTING SURFACES WITH A THICK ORGANIC FILM PROMOTING DROPWISE MODE

This article describes an experimental investigation of the condensation heat transfer of steam on dropwise and filmwise coexisting (DFC) surfaces, on which dropwise and filmwise exist simultaneously at adjacent positions. A fluor-containing organic film with thickness of more than 1 μm was coated on the dropwise regions of the external surface of a brass tube to promote dropwise condensation. The surfaces were divided horizontally into many regions according to the designed dropwise and filmwise condensation area ratio. The area ratio of dropwise regions and filmwise regions in the present study was fixed at 50%:50% for all the six surfaces, while the numbers of dropwise and filmwise regions ranged from 2 to 16. Experiments were conducted at atmospheric pressure and the treated tube was oriented vertically in the condensing chamber. It was found that the heat transfer performance for DFC surfaces increases with increasing number of dropwise and filmwise regions, and an enhancement ratio of 1.27 to 1.96 is realized compared with the results for bare surface. Visual observation revealed that the appearance of condensation near the boundary region between the dropwise and filmwise regions was dependent on the relative positions of the two condensation regions. The condensate flowed smoothly across the boundary for dropwise condensation in the upper region. With filmwise condensation in the upper region, a condensate ring was formed at the interface and was retained at the interface for a short period of time before collapsing and then continued to flow downward through the dropwise condensation region. The condensate ring made a remarkable contribution to the condensation heat transfer enhancement for DFC surfaces. Finally, the results also showed that the heat transfer enhancement for dropwise and filmwise coexisting surfaces depends not only on the area ratio on DFC surfaces, but also on the surface subcooling degree. An optimal coordinating condition between these two factors might realize a maximum heat transfer enhancement ratio.     

Dropwise Condensation of Steam on a Small Tube Bundle at Turbine Condenser Conditions

Application of dropwise condensation to utility turbine condensers is investigated by comparing the thermal performance of dropwise and filmwise bundles at industrially relevant conditions. Steam and steam-air mixtures were condensed on bundles of in-line, titanium tubes. The row-by-row heat transfer coefficients are presented against bundle position. They show the expected behavior for filmwise condensation but demonstrate a different one for dropwise. In air-free steam, the dropwise heat transfer coefficients are much larger and do not vary significantly with bundle position. In air-steam mixtures the dropwise values decrease similarly to their filmwise equivalents. The findings are in accord with those found for other geometries. The findings indicate that significant reductions in condenser size can be obtained if permanent dropwise condensation can be produced at industrially relevant conditions.     

滴状冷凝过程壁面反射光谱的分子团聚模型分析

根据反射光谱可用于分析固体表面介质凝聚状态的原理,理论分析了不锈钢表面上不同厚度薄液膜对表面反射率的影响,确定了在冷凝过程中该表面上冷凝液形成和更新过程导致相应反射率变化的范围. 通过分析滴状冷凝实验过程反射光谱的文献数据,研究了滴状冷凝过程壁面上蒸气分子凝聚特征,发现在实际的滴状冷凝传热过程中,液滴脱落后形成的裸露表面上存在反射特征介于液膜与体相蒸气分子之间的介质. 结合蒸气冷凝过程的分子团聚模型,得到了在滴状冷凝过程中近壁面附近的蒸气分子形成分子团聚分布的合理性. 此外,分析发现表面微观结构将改变团聚体分布密度,从而影响冷凝核化过程的现象. 这为冷凝传热强化方法的研究提出了新的思路. 关键词： 分子团聚 反射光谱 滴状冷凝     

流速对混合蒸汽Marangoni凝结换热影响的实验研究

本文在蒸汽压力为47.36 kPa的条件下,通过实验研究了不同蒸汽流速(u=2、4、5 m/s)下纯水和不同酒精浓度水-酒精混合蒸汽沿重力方向流过竖直紫铜平板表面上的凝结换热特性,并实现了实验的可视化,同时分析了不同蒸汽流速下造成Marangoni凝结换热特性差异的原因.实验及分析结果表明,在相同蒸汽浓度、蒸汽压力和表面过冷度条件下,高流速下的凝结换热系数比低流速的大.且蒸汽流速对凝结换热的影响因混合蒸汽酒精浓度的不同而不同,低浓度0.5%和高浓度50%时流速的增加对凝结换热特性的影响较小,而在中间浓度2%时凝结换热强度随流速的增加明显.     

ON THE ENHANCEMENT OF FILMWISE CONDENSATION HEAT TRANSFER BY MEANS OF THE COEXISTENCE WITH DROPWISE CONDENSATION SECTIONS

This article describes work aimed at obtaining higher filmwise condensation heat flux by distributing dropwise condensation surfaces of optimal width promoted by an organic coating among filmwise surfaces, and to get higher mean overall heat transfer coefficients in condensing systems. Several different spacings were examined for the horizontal orientation, arranging a dropwise section above a filmwise one, to make clear the effect of the drops falling down to the filmwise section. The heat flux of the filmwise part increased with increasing the height of the dropwise part up to 2 mm, but then decreased above that. The extent of the filmwise part that was augmented by drops was also tested by changing the width of the filmwise section sandwiched between dropwise sections of constant width. The heat flux of the filmwise part increased abruptly at a width between 5 and 3 mm. Consequently, it was shown that there exists an optimum width for each section for enhancing condensation heat transfer in the filmwise sections.