Preparation of Zn2+–Ni2+–Fe3+–CO32−LDHs and study of photocatalytic activities for decomposition of Methyl Orange solution

New type photocatalytic materials of Zn²⁺–Ni²⁺–Fe³⁺–CO₃^2?LDHs were prepared by complexing agent-assisted homogeneous precipitation technique and Zn(NO₃)₂·6H₂O, Ni(NO₃)·6H₂O, Fe(NO₃)₃·9H₂O used as raw materials in the case of molar ratio of Zn²⁺/Ni²⁺/Fe³⁺ = 1:6:2. Zn²⁺–Ni²⁺–Fe³⁺–CO₃^2?LDHs having a specific surface area of 96.5 m²/g. The structure and catalytic properties of the material were systematically studied. The experimental results show that the Zn²⁺–Ni²⁺–Fe³⁺–CO₃^2?LDHs has a higher adsorption performance and lower band gap which make it an excellent catalyst for reducing the degradation of the methyl orange. Study on the process of photocatalytic reaction shows that Methyl Orange was adsorbed to the layer of Zn²⁺–Ni²⁺–Fe³⁺–CO₃^2?LDHs, and then it was photodecomposed to inorganic molecules and ions by Zn²⁺, Ni²⁺, and Fe³⁺ on the surface of Zn²⁺–Ni²⁺–Fe³⁺–CO₃^2?LDHs.     

The effect of different gas atmospheres on luminescent properties of pulsed laser ablated SrAl2O4:Eu,Dy thinfilms

SrAl₂O₄:Eu²⁺,Dy³⁺ thin films were grown on Si (1 0 0) substrates using the pulsed laser deposition (PLD) technique to investigate the effect of vacuum, oxygen (O₂) and argon (Ar) deposition atmospheres on the structural, morphological, photoluminescence (PL) and cathodoluminescence (CL) properties of the films. The films were ablated using a 248 nm KrF excimer laser. Atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS) and fluorescence spectrophotometry were used to characterize the thin films. Auger electron spectroscopy (AES) combined with CL spectroscopy were employed for the surface characterization and electron-beam induced degradation of the films. Better PL intensities were obtained from the unannealed films prepared in Ar and O₂ atmospheres with respect to those prepared in vacuum. A stable green emission peak at 515 nm, attributed to 4f⁶5d¹→4f⁷ Eu²⁺ transitions were obtained with less intense peaks at 619 nm, which were attributed to transitions in Eu³⁺. After annealing the films prepared in vacuum at 800 °C for 2 h, the intensity of the green emission (520 nm) of the thin film increased considerably. The amorphous thin film was crystalline after the annealing process. The CL intensity increased under prolonged electron bombardment during the removal of C due to electron stimulated surface chemical reactions (ESSCRs) on the surface of the SrAl₂O₄:Eu²⁺, Dy³⁺ thin films. The CL stabilized and stayed constant thereafter.     

Surface characterization and luminescent properties of SrAl2O4:Eu,Dy nano thin films

SrAl₂O₄:Eu²⁺, Dy³⁺ thin films were grown on Si (1 0 0) substrates in different atmospheres using the pulsed laser deposition (PLD) technique. The effects of vacuum, oxygen (O₂) and argon (Ar) deposition atmospheres on the structural, morphological and photoluminescence (PL) properties of the films were investigated. The films were ablated using a 248 nm KrF excimer laser. Improved PL intensities were obtained from the unannealed films prepared in Ar and O₂ atmospheres compared to those prepared in vacuum. A stable green emission peak at 520 nm, attributed to 4f⁶5d¹→4f⁷ Eu²⁺ transitions was obtained. After annealing the films prepared in vacuum at 800 °C for 2 h, the intensity of the green emission (520 nm) of the thin film increased considerably. The amorphous thin film was crystalline after the annealing process. The diffusion of adventitious C into the nanostructured layers deposited in the Ar and O₂ atmospheres was most probably responsible for the quenching of the PL intensity after annealing.     

掺铒高硅氧玻璃光谱性质的研究

应用Judd-Oflet理论计算了新型掺铒高硅氧玻璃中铒离子的强度参量Ω_t(t=2,4,6)，Ω₂=8.15×10^-20，Ω₄=1.43×10^-20，Ω₆=1.22×10^-20，相比于其他氧化物玻璃，表现出较大的Ω_2,6值，反映了铒离子周围的近邻结构不对称性和Er-O键的离子键成分较高.利用McCumber理论计算得到了能级^{关键词： 掺铒高硅氧玻璃 Judd-Ofelt理论 量子效率}     

Corelationship between local structure and water purifying ability of iron-containing waste glasses

A relationship between the structure and water purifying ability of waste glass prepared from household garbage and Fe₂O₃ was examined by ⁵⁷Fe-Mössbauer and induced coupled plasma (ICP) measurements. From the Debye temperature of waste glass, Fe^II proved to be loosely bound in the glass network as a network modifier. Dissolution amount of Fe^III into artificial drain can be controlled from 0.14 to 0.35 mg/l by changing the Fe₂O₃ content. It proved that chemical oxygen demand (COD) decreases in proportion to the content of Fe^III, indicating that iron causes decomposition of organic and phosphorus compounds.     

Mechanism of enhanced photocatalysis of TiO2 by Fe in suspensions

In this work, the mechanism of enhanced photocatalysis of TiO₂ with Fe³⁺ was studied using Sulfadiazine (SD) as the model compound. Results indicated that degradation rate of SD was enhanced by the addition of Fe³⁺ in TiO₂ suspension. The crystalline structure of TiO₂ particles was stable in suspensions. The hydroxyl radical generated by TiO₂/Fe³⁺ (both TiO₂ and Fe³⁺) photocatalysis was in a higher yield. Moreover, Fe²⁺ was found not to give an obvious impact on the SD degradation in TiO₂ suspension, whereas Fe³⁺ had a notable effect. The adsorption amount of TiO₂ was greatly enhanced by the addition of Fe³⁺ in suspensions. Finally, an interaction model of SD degradation in TiO₂ suspension containing Fe³⁺ was also proposed by investigating of surface behaviors of TiO₂ particles. It will be beneficial to use Fe³⁺ as the electron acceptors on the surface of TiO₂ particles, which helps to improve the yield of hydroxyl radical.     

Stabilization of the anatase phase in TiO2(Fe, PEG) nanostructured coatings

Multilayered TiO₂(Fe³⁺, PEG) films were deposited on glass and SiO₂/glass substrates by sol-gel dipping method. The influence of Fe³⁺ and PEG(polyethylene glycol) concentrations, the number of layers, the thermal treatment time and the temperature on the optical and microstructural properties of the TiO₂ films were studied.As-deposited TiO₂(Fe³⁺, PEG) films were very porous, but after the thermal treatment at 500 °C, the PEG decomposed and burned out to porosity decreasing. Homogeneous nanostructured films were obtained, where the amorphous and the anatase phases coexist. XRD analysis showed that no rutile phase is observed in the films deposited on SiO₂/glass as compared with those deposited directly on glass and that the presence of the anatase phase in the films without PEG is more evident in the three-layers film. The XRD intensity of the main peak of anatase from 25° decreases with the increase of PEG concentration.The optical gap of the TiO₂(Fe³⁺, PEG) films is found in 2.52-2.56 eV range and does not essentially depend on the PEG content.     

High-frequency magnetic properties of soft magnetic cores based on nanocrystalline alloy powder prepared by thermal oxidation

FeSiBNbCu nanocrystalline alloy powder was thermally oxidized in an air atmosphere to enhance an oxide layer formation on the surface of the powder and subsequently toroidal shape FeSiBNbCu nanocrystalline alloy powder cores were prepared by compaction at room temperature. The phase change on the surface of FeSiBNbCu nanocrystalline alloy powder by thermal oxidation was analyzed and its effect on the high frequency magnetic properties of the compacted cores was investigated. By thermal oxidation, the formation of the oxide layer consisting of Fe₂O₃, CuO, and SiO₂ on the surface of FeSiBNbCu nanocrystalline alloy powder was enhanced and the thickness of oxide layer could be controlled by changing the thermal oxidation time. FeSiBNbCu nanocrystalline alloy powder core prepared from the powder treated by thermal oxidation exhibits a stable permeability up to high frequency range over 10 MHz. The core loss could be reduced remarkably and the dc-bias property could be improved significantly, which were due to the formation of oxide layer consisting of Fe₂O₃, CuO, and SiO₂ on the FeSiBNbCu nanocrystalline alloy powder. The improvement in high-frequency magnetic properties of the FeSiBNbCu nanocrystalline alloy powder cores could be attributed to the effective electrical insulation by oxide layer between the FeSiBNbCu nanocrystalline alloy powders.     

Surface oxidation in a van der Waals ferromagnet Fe3-xGeTe2

We investigate the surface oxidation in a van der Waals ferromagnet Fe_3-xGeTe₂, a material widely utilized for spintronic applications. While known for its relative air-insensitivity, exposure to air during the handling process (e.g. device or heterostructure fabrication) can lead to reduction or disappearance of its magnetic signal. Comparison of x-ray absorption and x-ray magnetic circular dichroism spectra between pristine and air-exposed Fe_3-xGeTe₂ confirm a naturally oxidized surface layer on the material. The surface oxide layer has predominantly Fe³⁺ content. X-ray absorption spectroscopy done on micron-sized exfoliated Fe_3-xGeTe₂ flakes reveal that the change in the surface chemical properties can be quite significant for thin flakes. The surface modulation of Fe_3-xGeTe₂ can lead to inaccuracies in characterizing its interfacial magnetic and spin transport properties, and complicate device and heterostructure fabrication processes.     

The transformation of mackinawite into greigite studied by Raman spectroscopy

In this study, Raman spectroscopy was used to precisely understand the mechanisms of oxidation of mackinawite (FeS). Two experimental conditions were considered: (1) oxidation in air at room temperature and (2) oxidation in acidic anoxic solutions at 80 °C. In both cases, the oxidation process began by the in situ oxidation of Fe(II) cations inside the crystal structure of mackinawite and led to Fe(III)‐containing mackinawite, Fe^II_1−3xFe^III_2xS. The oxidation in air finally led to Fe(III) oxyhydroxides and elemental sulfur α‐S₈, but greigite (Fe₃S₄) was observed as an intermediate compound. In anoxic acidic solutions, the product of the oxidation was proved to depend on the Fe/S concentration ratio. For Fe/S = 3/4, greigite was the only product obtained, and this allowed us to determine unambiguously the Raman spectrum of this compound. Copyright © 2010 John Wiley & Sons, Ltd.     

Iron ions in ZSM-5 zeolite: Fe3+ in framework, Fe2+ in extra-framework positions in catalytic N2O decomposition

Fe-ZSM-5 samples containing a combination of ⁵⁷Fe³⁺ in framework (FW) and regular iron in extra-framework (EFW) sites were prepared by introducing ⁵⁷Fe in hydrothermal synthesis, then exchanging Fe²⁺ of natural isotope composition into the lattice. The stability for one part of Fe²⁺ and Fe²⁺ ? Fe³⁺ reversibility for the other part in catalytic decomposition of N₂O is demonstrated by in situ Mössbaer measurements. Formation of dinuclear Fe_FW–O–Fe_EFW pairs is not prevailing.     

注入Ar+的蓝宝石晶体退火前后光致发光谱的分析

对注入Ar⁺后不同晶面取向的蓝宝石晶体在不同退火条件下的光致发光谱进行了分析.分析结果表明:三种晶面取向的蓝宝石样品经Ar⁺注入后,其光致发光谱中均出现了新的位于506nm处的发光峰;真空和空气气氛下的退火均对样品在506nm处的发光有增强作用,不同晶面取向的样品发光增强程度不同,且发光增强至最大时的退火温度也不同,空气气氛下的退火使样品发光增强程度更为显著.由此可以看出,退火气氛、退火温度和晶面取向均对样品发光峰强度有影响. 关键词： 2O₃')" href="#">Al₂O₃ 离子注入 退火 光致发光谱     

Surface properties of Fe76Mo8Cu1B15 alloy after annealing

NANOPERM-type alloy Fe₇₆Mo₈Cu₁B₁₅ is investigated in amorphous and in partially crystallized state. Samples were prepared by 1 h isothermal annealing in vacuum at temperatures ranging from 330°C up to 700°C. Bulk and surface microstructural characteristics were studied using transmission and conversion electron Mössbauer effect techniques, respectively. Surface features were checked by the help of atomic force microscopy. Presence of nanocrystalline bcc-Fe phase was detected during the first crystallization stage. The crystallization process starts at 450°C and it is more pronounced in surface regions than in the bulk. With progressing crystallization, hyperfine parameters especially of the amorphous residual phase are altered. Distinctions in surface morphology are revealed between wheel and air side of the ribbon-shaped samples.     

Theory studies of the local lattice distortions and the EPR parameters for Cu2+, Mn2+ and Fe3+ centres in ZnWO4

The local lattice distortions and the electron paramagnetic resonance (EPR) parameters (g factors, hyperfine structure constants and zero-field splittings) for Cu²⁺, Mn²⁺ and Fe³⁺ in ZnWO₄ are theoretically studied based on the perturbation calculations for rhombically elongated octahedral 3d⁹ and 3d⁵ complexes. The impurity centres on Zn²⁺ sites undergo the local elongations of 0.01, 0.002 and 0.013 Å along the C₂ axis and the planar bond angle variations of 8.1°, 8.0° and 8.6° for Cu²⁺, Mn²⁺ and Fe³⁺, respectively, due to the Jahn–Teller effect and size and charge mismatch. In contrast to the host Zn²⁺ site with obvious axial elongation (～0.31 Å) and perpendicular (angular) rhombic distortion, all the impurity centres demonstrate more regular octahedral due to the above local lattice distortions. The copper centre exhibits significant Jahn–Teller reductions for the spin-orbit coupling and orbital angular momentum interactions, characterised by the Jahn–Teller reduction factor J (≈0.29 ? 1). The calculated EPR parameters agree well with the experimental results. The local structures of the impurity centres are analysed in view of the corresponding lattice distortions.     

Monitoring synchrotron X‐ray‐induced radiolysis effects on metal (Fe,W) ions in high‐temperature aqueous fluids

Radiolysis‐induced effects on aqueous tungsten ions are observed to form a precipitate within seconds upon exposure to a synchrotron X‐ray micro‐beam in a WO₃ + H₂O system at 873 K and 200 MPa. In situ Fe K‐edge energy‐dispersive X‐ray absorption spectroscopy (ED‐XAS) measurements were made on Fe(II)Cl₂ aqueous solutions to 773 K in order to study the kinetics of high‐temperature reactions of Fe²⁺ and Fe³⁺ ions with transient radiolysis species. The radiolytic reactions in a fluid sample within a hydrothermal diamond anvil cell result in oxidation of the Fe²⁺ ion at 573 K and reduction of Fe³⁺ at temperatures between 673 and 773 K and of the Fe²⁺ ion at 773 K. The edge‐energy drift evident in the ED‐XAS data directly reflects the kinetics of reactions resulting in oxidation and/or reduction of the Fe²⁺ and Fe³⁺ ions in the aqueous solutions at high temperatures. The oxidation and reduction trends are found to be highly consistent, making reliable determinations of reaction kinetics possible.     

Electronic structure studies of the spinel CoFe2O4 by X-ray photoelectron spectroscopy

The spinel CoFe₂O₄ has been synthesized by combustion reaction technique. X-ray photoelectron spectroscopy shows that samples are near-stoichiometric, and that the specimen surface both in the powder and bulk sample is most typically represented by the formula (Co_0.4Fe_0.6)[Co_0.6Fe_1.4]O₄, where cations in parentheses occupy tetrahedral sites and those within square brackets in octahedral sites. The results demonstrate that most of the iron ions are trivalent, but some Fe²⁺ may be present in the powder sample. The Co 2p_3/2 peak in powder sample composed three peaks with relative intensity of 45%, 40% and 15%, attributes to Co²⁺ in octahedral sites, tetrahedral sites and Co³⁺ in octahedral sites. The O 1s spectrum of the bulk sample is composed of two peaks: the main lattice peak at 529.90 eV, and a component at 531.53 eV, which is believed to be intrinsic to the sample surface. However, the vanishing of the O 1s shoulder peak of the powder specimen shows significant signs of decomposition.     

同位素示踪法研究铜薄膜在水汽中的氧化传质机理

采用H¹⁶₂O/H¹⁸₂O接续氧化并结合同位素示踪方法,研究了铜薄膜在水汽中氧化的传质机理.将真空热蒸发制备的铜薄膜样品,分别在H¹⁶₂O,H¹⁸₂O中以及H¹⁶₂O/H¹⁸₂O接续进行氧化处理;利用X射线衍射(XRD)研究了氧化产物的形态和结构 关键词： 同位素示踪 短路扩散 铜薄膜 18₂O')" href="#">H¹⁸₂O     

Role of Al2O3 in upconversion and NIR emission in Tm and Er codoped calcium fluoro phosphorous silicate glass system

In this study, the principal role of Al₂O₃ on the features of the photoluminescence spectra of Tm³⁺ ion and upconversion phenomenon in Tm³⁺ and Er³⁺ codoped CaF₂−Al₂O₃−P₂O₅−SiO₂ glass system has been investigated. The concentration of Al₂O₃ is varied from 2 to 10 mol% while that of Er³⁺ and Tm³⁺ is fixed. IR and Raman spectral studies have indicated that there is a gradual increase in the degree of disorder in the glass network with increase in the concentration of Al₂O₃ up to 6.0 mol%. This is attributed to the presence of Al³⁺ ions in octahedral positions in larger proportions. When the glasses are doped with Tm³⁺ ions, the blue and red emissions were observed, whereas in Er³⁺ doped glasses blue, green and red emissions were observed. When the glasses are codoped with Tm³⁺ and Er³⁺ ions and excited at 790 nm, all the three emission lines were observed to be reinforced, especially in the glasses mixed with 6.0 mol% of Al₂O₃. The IR emission band detected at about 1.8 μm due to ³F₄→³H₆ transition of Tm³⁺ ions is also observed to be strengthened due to codoping. The reasons for enhancement in the intensity of various emission bands due to codoping have been identified and discussed with the help of rate equations for various emission transitions.     

Preparation and characterization of silica-coated Fe3O4 nanoparticles used as precursor of ferrofluids

Fe₃O₄ magnetic nanoparticles (MNPs) were synthesized by the co-precipitation of Fe³⁺ and Fe²⁺ with ammonium hydroxide. The sodium citrate-modified Fe₃O₄ MNPs were prepared under Ar protection and were characterized by Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), X-ray powder diffraction (XRD) and vibrating sample magnetometer (VSM). To improve the oxidation resistance of Fe₃O₄ MNPs, a silica layer was coated onto the modified and unmodified MNPs by the hydrolysis of tetraethoxysilane (TEOS) at 50 °C and pH 9. Afterwards, the silica-coated Fe₃O₄ core/shell MNPs were modified by oleic acid (OA) and were tested by IR and VSM. IR results revealed that the OA was successfully grafted onto the silica shell. The Fe₃O₄/SiO₂ core/shell MNPs modified by OA were used to prepare water-based ferrofluids (FFs) using PEG as the second layer of surfactants. The properties of FFs were characterized using a UV-vis spectrophotometer, a Gouy magnetic balance, a laser particle size analyzer and a Brookfield LVDV-III+ rheometer.     

Deep reduction behavior of iron oxide and its effect on direct CO oxidation

Reduction of metal oxide oxygen carrier has been attractive for direct CO oxidation and CO₂ separation. To investigate the reduction behaviors of iron oxide prepared by supporting Fe₂O₃ on γ-Al₂O₃ and its effect on CO oxidation, fluidized-bed combustion experiments, thermogravimetric analyzer (TGA) experiments, and density functional theory (DFT) calculations were carried out. Gas yield (γCO₂) increases significantly with the increase of temperature from 693 K to 1203 K, while carbon deposition decreases with the increase of temperature from 743 K to 1203 K, where temperature is a very important factor for CO oxidation by iron oxide. Further, it were quantitatively detected that the interaction between CO and Fe₂O₃, breakage of O-Fe bonds and formation of new C-O bonds, and effect of reduction degree were quantitatively detected. Based on adsorptions under different temperatures and reducing processes from Fe³⁺ into Fe²⁺, Fe⁺ and then into Fe, it was found that Fe²⁺ → Fe⁺ was the reaction-controlling step and the high oxidation state of iron is active for CO oxidation, where efficient partial reduction of Fe₂O₃ into FeO rather than complete reduction into iron may be more energy-saving for CO oxidation.