Rare earth photoionization study by the resonant microwave cavity technique

Photoconductivity spectra of rare earth-doped insulating materials are measured using the resonant microwave cavity method. This technique is based on the detection of the cavity Q-factor changes induced by irradiation of the sample (inserted in the cavity) by a pulsed tunable laser. Results obtained with Lu₂(SiO₄)O:Ce³⁺ and BaF₂:Eu²⁺ are presented and discussed. Photoionization thresholds at 400 nm (3.1 eV) and 310 nm (4.0 eV) are measured for Lu₂(SiO₄)O:Ce³⁺ and BaF₂:Eu²⁺, respectively.     

94-GHz 25-kW CW low-voltage harmonic gyrotron

A low-voltage second-harmonic gyrotron intended as a compact lightweight source has been designed and evaluated with a particle-tracing code and the particle-in-cell code MAGIC. The two codes are shown to be in good agreement when applied to a conventional fundamental-frequency gyrotron and also to the novel second-harmonic gyrotron. The 25-kW continuous wave (CW) 94-GHz gyrotron with a predicted conversion efficiency of 32% and device efficiency of 22.5% is driven by a 25-kV 4.5-A (υ_⊥/υ₂=1.5, Δυ_z/υ_z=7%) electron beam from a magnetron injection gun and employs a low-loss TE₀₂₁/TE₀₃₁ complex cavity for mode control. Although the 17-kG CW gyrotron will use a cryogen-free high-T_c superconducting magnet, a 94-GHz prototype will be tested at low duty with a conventional low-T_c superconducting magnet     

基于SESAM被动调Q的激光二极管泵浦Yb∶CaYAlO_4脉冲激光器

采用发射波长约为976 nm的半导体激光器作为泵浦源,Yb~(3+)掺杂浓度为1. 5at.%、通光长度为2 mm的Yb∶CaYAlO_4晶体作为增益介质,本文提出了一种基于半导体可饱和吸收镜(SESAM)被动调Q的激光二极管泵浦Yb∶CaYAlO_4以获取稳定脉冲输出的方案。通过合理设计谐振腔,实现了稳定的被动调Q激光脉冲输出,并分析了泵浦功率的大小对输出脉冲的重复频率、脉冲宽度、单脉冲能量以及脉冲峰值功率的影响。     

Design of a permanent magnet with a mechanical sweep suitable for variable-temperature continuous-wave and pulsed EPR spectroscopy

A magnetic system is introduced which consists of three nested rings of permanent magnets of a Halbach dipolar layout and is capable for EPR spectroscopy. Two of the rings can be rotated independently to adjust the magnetic flux in the center and even allow for mechanical field sweeps. The presented prototype achieves a magnetic flux range of 0.0282–0.3013 T with a minimal sweep of 0.15 mT and homogeneity of about 10⁻³.First applications with CW and pulsed Mims ENDOR as well as ESEEM experiments on a sample of a glycine single crystal doped with 1% copper nitrate demonstrate that flux range, sweep accuracy and homogeneity of this prototype is sufficient for EPR experiments on most solid samples.Together with a recently improved design magnets can be build which could serve as compact and easily transportable replacement of standard electromagnets with negligible consumption of power or coolants.     

共焦腔增强的空气拉曼散射

拉曼光谱是一种无损、快速的物质成分分析和检测方法.由于拉曼信号强度微弱,使得拉曼光谱的检测应用受到极大的限制.针对增强拉曼散射信号强度、提高检测灵敏度这一问题,设计了一种用于自发拉曼散射信号增强的共焦腔样品池,开展了基于该共焦腔的空气拉曼散射信号增强研究.共焦腔的腔镜反射率为92%,这一设计在保证共焦腔通带宽度与激光器线宽匹配的同时能有效地降低共振调节难度.实验中采用0°探测构型收集拉曼信号,并由成像式拉曼光谱仪获取光谱信号.实验发现,在共振状态下,共焦腔的耦合效率达到87.5%,单向激光功率实现约11倍放大;与无共振腔相比,共焦腔对拉曼信号实现17倍放大,信噪比提高2倍.此外,空气中CO_2的3σ检测限达到200 ppm量级.结果表明,该系统对自发拉曼散射信号增强效果显著,并且有较高的检测灵敏度.     

X波段脉冲电子顺磁共振谱仪的矩形腔与微型平面腔的设计

为了满足脉冲式电子顺磁共振谱仪的需要,设计并制作了连续波谐振腔和脉冲谐振腔. 连续波谐振腔采用矩形谐振腔的设计,而脉冲谐振腔采用了微型平面腔的设计. 在设计阶段,使用Ansoft-HFSS三维电磁仿真软件对2种谐振腔进行模拟计算. 微型平面腔的加工采用了微纳加工技术. 制作完成的谐振腔的参数指标由网络分析仪测定. 实验测得2种谐振腔的参数指标符合理论模拟值,并满足脉冲式电子顺磁共振谱仪的要求.     

镶嵌于多孔硅微腔中8-羟基喹啉铝的窄峰发射

利用浸渍法将8羟基喹啉铝(Alq₃)镶嵌到多孔硅微腔中,制备了多孔硅微腔—Alq₃镶嵌膜,研究了多孔硅微腔对镶嵌其中的Alq₃自发发射的微腔效应,观察到了光谱窄化、发光强度增强等现象。镶嵌于多孔硅微腔中的Alq₃荧光光谱的半峰全宽只有15nm,而非微腔样品,即镶嵌于普通的单层多孔硅中Alq₃荧光谱半峰全宽在85nm以上。并且有微腔时Alq₃发光强度比没有微腔时Alq₃发光强度增强一个数量级。随机改变微腔中Bragg反射镜高折射率层的几何厚度可使高反射区展宽,从而更加有效地抑制了多孔硅本身的发光模,使发光色度更纯,但由于峰值透射率减小,导致共振峰强度有所减小。多孔硅微腔有机镶嵌膜有可能成为进一步发展Alq₃在电致发光器件方面应用的一条新途径。     

一种X波段过模高效率相对论返波管

设计了一种X波段过模高效率相对论返波管(RBWO),主要结构包括双谐振腔反射器、7周期梯形慢波结构与提取腔。该器件慢波结构的过模比为2.6,电子束与结构波TM₀₁模的近π模相互作用,在慢波结构区域束波作用产生的TM₀₁模表面波主要转化为TM₀₂模的体波,其输出微波的模式主要为TM₀₂模,占比为81%,其余为TM₀₁模。提出一种过模条件下谐振腔反射器的设计思路,结合模式匹配法,优化得到了一种双谐振腔反射器结构,其对TM₀₁模与TM₀₂模的反射系数均大于0.99,可实现过模条件下RBWO慢波结构与二极管区的良好隔离; 同时双谐振腔反射器两个谐振腔中的纵向电场可以对电子束进行充分的预调制,将促进慢波结构区域的束波作用,有利于提升效率。通过在慢波结构后端加入提取腔,进一步提升了转换效率。PIC仿真中, 在二极管电压900 kV,电流14.3 kA,得到了6.6 GW的输出功率,转换效率约51%。     

Long-distance super-exchange and quantum magnetic relaxation in a hybrid metal–organic framework

The hybrid metal–organic framework [(CH3)2NH2]Fe(HCOO)3with a perovskite-like structure exhibits a variety of unusual magnetic behaviors at low temperatures. While the long-distance super-exchange through the Fe-O–CH-O–Fe exchange path leads to a canted antiferromagnetic ordering at TN～ 19 K, a second transition of magnetic blocking develops at TB～ 9 K. The stair-shaped magnetization hysteresis loops below TBresemble the behaviors of resonant quantum tunneling of magnetization in single-molecular quantum magnets. Moreover, the magnetic relaxation also exhibits several features of resonant quantum relaxation, such as the exponential law with a single characteristic relaxation time, and the nonmonotonic dependence of relaxation rate on the applied magnetic field with a much faster relaxation around the resonant fields. The origin of quantum tunneling behaviors in the [(CH3)2NH2]Fe(HCOO)3metal–organic framework is discussed in terms of magnetic phase separation due to the modification of hydrogen bonding on the long-distance super-exchange interaction.     

Optical-EPR double resonance studies of erbium doped lithium yttrium fluoride

Fluorescence modulation has been used to optically detect excited state paramagnetic resonance of Er³⁺in LiYF₄. Ground state EPR has been similarly detected both through resonant reabsorption of the fluorescence and memory effects active over the optical absorption—emission cycle.     

Comparison of Continuous Wave, Spin Echo, and Rapid Scan EPR of Irradiated Fused Quartz

The E' defect in irradiated fused quartz has spin lattice relaxation times (T(1)) about 100 to 300 μs and spin-spin relaxation times (T(2)) up to about 200 μs, depending on the concentration of defects and other species in the sample. These long relaxation times make it difficult to record an unsaturated continuous wave (CW) electron paramagnetic resonance (EPR) signal that is free of passage effects. Signals measured at X-band (~9.5 GHz) by three EPR methods: conventional slow-scan field modulated EPR, rapid scan EPR, and pulsed EPR, were compared. To acquire spectra with comparable signal-to-noise, both pulsed and rapid scan EPR require less time than conventional CW EPR. Rapid scan spectroscopy does not require the high power amplifiers that are needed for pulsed EPR. The pulsed spectra, and rapid scan spectra obtained by deconvolution of the experimental data, are free of passage effects.     

Design and experimental verification of a dual-band metamaterial filter

In this paper, we present the design, simulation, and experimental verification of a dual-band free-standing metamaterial filter operating in a frequency range of 1 THz–30 THz. The proposed structure consists of periodically arranged composite air holes, and exhibits two broad and flat transmission bands. To clarify the effects of the structural parameters on both resonant transmission bands, three sets of experiments are performed. The first resonant transmission band shows a shift towards higher frequency when the side width w_1 of the main air hole is increased. In contrast, the second resonant transmission band displays a shift towards lower frequency when the side width w_2 of the sub-holes is increased, while the first resonant transmission band is unchanged. The measured results indicate that these resonant bands can be modulated individually by simply optimizing the relevant structural parameters(w_1 or w_2) for the required band. In addition, these resonant bands merge into a single resonant band with a bandwidth of 7.7 THz when w_1 and w_2 are optimized simultaneously. The structure proposed in this paper adopts different resonant mechanisms for transmission at different frequencies and thus offers a method to achieve a dual-band and low-loss filter.     

Comparing continuous wave progressive saturation EPR and time domain saturation recovery EPR over the entire motional range of nitroxide spin labels

The measurement of spin-lattice relaxation rates from spin labels, such as nitroxides, in the presence and absence of spin relaxants provides information that is useful for determining biomolecular properties such as nucleic acid dynamics and the interaction of proteins with membranes. We compare X-band continuous wave (CW) and pulsed or time domain (TD) EPR methods for obtaining spin-lattice relaxation rates of spin labels across the entire range of rotational motion to which relaxation rates are sensitive. Model nitroxides and spin-labeled biological species are used to illustrate the potential complications that arise in extracting relaxation data under conditions typical to biological experiments. The effect of super hyperfine (SHF) structure is investigated for both CW and TD spectra. First and second harmonic absorption and dispersion CW spectra of the nitroxide spin label, TEMPOL, are all fit simultaneously to a model of SHF structure over a range of microwave amplitudes. The CW spectra are novel because all harmonics and microwave phases were acquired simultaneously using our homebuilt CW/TD spectrometer. The effect of the SHF structure on the pulsed free induction decay (FID) and pulsed saturation recovery spectrum is shown for both protonated and deuterated TEMPOL. We present novel pulsed saturation recovery measurements on biological molecules, including spin-lattice relaxation rates of spin-labeled proteins and spin-labeled double-stranded DNA. The impact of structure and dynamics on relaxation rates are discussed in the context of each of these examples. Collisional relaxation rates with oxygen and transition metal paramagnetic relaxants are extracted using both continuous wave and time domain methods. The extent of the errors inherent in the CW method and the advantages of pulsed methods for unambiguously measuring collisional relaxation rates are discussed. Spin-lattice relaxation rates, determined by both CW and pulsed methods, are used to determine the electrostatic potential on the surface of a protein.     

辐照用紧凑连续波电子加速器的物理设计

为适应工业电子加速器需求增多的现状,提出了一种新型的结构紧凑的连续波电子加速器,运行频率为180MHz。依靠置于加速腔外的多个偏转磁铁,使电子束多次穿越加速腔,从而得到持续的加速。设计过程中,用CST软件对谐振加速腔进行了优化,用Parmela软件模拟了束流的粒子动力学。粒子纵向稳定度和横向聚焦也通过模拟进行了分析和验证。结果显示:此种新型加速器能得到9MeV,100kW的稳定电子束流。     

0.3 THz TM10, 1, 0模同轴耦合腔链

通过本征方程研究了工作在太赫兹(THz)频段的高次模同轴谐振腔,讨论了TM_{m, 1, 0}模,TM_{m, 2.0}模与TM_{m, 1, 1}模的谐振频率与腔体的几何参数之间的关系,并给出了工作模式的选择依据。在此基础上,提出了一种新型的0.3 THz TM_{10, 1, 0}模同轴耦合腔链,使用等效电路模型和CST-MWS软件对耦合腔链的色散特性、特征阻抗和电场分布等冷腔特性进行了分析和仿真,并着重分析和总结了耦合腔链的几何参数对色散特性和特征阻抗的影响。研究结果表明:对于工作在THz频段的高次模同轴耦合腔链,采用TM_{10, 1, 0}模为工作模式是合理的选择; 工作于2π腔模的0.3 THz TM_{10, 1, 0}模同轴耦合腔链具有较大的特征阻抗,但模式间隔较小,因此可将其应用于窄带太赫兹扩展互作用器件; 增大高次模耦合腔链的耦合槽张角是增大模式间隔的最佳途径。     

Theoretical Studies of Electron Paramagnetic Resonance Parameters for Cr4+ Ions in Ca2GeO4 Crystals

The electron paramagnetic resonance (EPR) parameters (zero-field splitting D and g factors g_||, g_⊥) of Cr⁴⁺ ions in Ca₂GeO₄ crystals have been calculated from the complete high-order perturbation formulas of EPR parameters for a 3d² ion in trigonal MX₄ clusters. In these formulas, in addition to the contributions to EPR parameters from the widely used crystal-field (CF) mechanism, the contributions from the charge-transfer (CT) mechanism (which are often neglected) are included. From the calculations, it is found that for the high valence state 3dⁿ ions in crystals, the reasonable explanation of EPR parameters (in particular, the g factors) should take both the CF and CT mechanisms into account.     

Evaluation and comparison of pulsed and continuous wave radiofrequency electron paramagnetic resonance techniques for in vivo detection and imaging of free radicals

The performance of two electron paramagnetic resonance (EPR) spectrometers/imagers, one configured in pulsed mode and the other in continuous wave (CW) mode, at an operating frequency of 300 MHz is compared. Using the same resonator (except for altered Q-factors), identical samples and filling factors in the two techniques have been evaluated for their potentials and limitations for in vivo spectroscopic and imaging applications. The assessment is based on metrics such as sensitivity, spatial and temporal resolution, field of view, image artifacts, viable spin probes, and subjects of study. The spectrometer dead time limits the pulsed technique to samples with long phase memories (>275 ns). Nevertheless, for viable narrow-line spin probes, the pulsed technique offers better sensitivity and temporal resolution. The CW technique, on the other hand, does not restrict the choice at spin probes. In addition, the phase-sensitive narrow-band detection of the CW technique gives artifact-free images even for large objects. Selected examples illustrating the performance of the CW and pulsed techniques are presented to put the capabilities of the two techniques in perspective.     

A microwave absorption study in the thermochromic SrMnO3

We report electron paramagnetic resonance (EPR) and magnetically modulated microwave absorption spectroscopy (MAMMAS) studies at X-band (8.8–9.6 GHz) on powdered SrMnO₃ in the 90–400 K temperature range. EPR spectrum shows one broad single-line at room temperature, which is observed only above 280.5 K, being compatible with an antiferromagnetic order. The onset of the para–antiferromagnetic transition has been determined from the temperature dependence of three main parameters extracted from the EPR spectra: resonant field (H_res), peak-to-peak linewidth (ΔH_pp) and integrated intensity (I_EPR). The MAMMAS response shows a change in the region 276–283 K, compatible with the para–antiferromagnetic transition, without presenting any significant change in the region of thermochromism.     

Spin dynamics in continuous wave and pulsed ENDOR spectroscopy of coals

ENDOR experiments on coals recorded using continuous wave (CW) and pulsed techniques appear to give qualitatively different spectra. A matrix proton signal dominates the ENDOR spectrum of coals recorded in the CW ENDOR experiment while both a matrix and local proton ENDOR signals with huperfine couplings of up to 20 MHz are observed in spectra recorded using pulsed excitation techniques. Analysis of these spectra lead to different implications for the structure of the molecules that host the unpaired electron. Using a combination of pulsed EPR (Electron Spin Echo, FID detected hole burning) and pulsed Electron Nuclear Multiple Resonance (Sub-level relaxation, hyperfine selective ENDOR, EPR sub-spectra) experiments, we investigate the electron and nuclear spin dynamics in order to reconcile the different signal amplitudes observed in the CW and pulsed ENDOR spectra. In the CW ENDOR experiment, the results of the FID detected hole burning experiments prove that the low ENDOR signal intensity can not be attributed to spectral diffusion mechanisms competing with ENDOR mechanisms. Instead, we find that an unfavorable ratio of the electron and nuclear spin relaxation rates results in small local ENDOR signals. The matrix line dominates the spectrum because of the large number of matrix protons. In the pulsed ENDOR experiment, the hyperfine contrast selectivity mechanism suppresses the intensity of the matrix ENDOR signal and enhances the amplitudes of the local ENDOR signals. In addition, the ENDOR signal is not a function of the ratio of the electron and nuclear relaxation rates.     

Surface plasmon resonance and field confinement in graphene nanoribbons in a nanocavity

In this work, we demonstrate surface plasmon resonance properties and field confinement under a strong interaction between a waveguide and graphene nanoribbons (GNRs), obtained by coupling with a nanocavity. The optical transmission of a waveguide–cavity–graphene structure is investigated by finite-difference time-domain simulations and coupled-mode theory. The resonant frequency and intensity of the GNR resonant modes can be precisely controlled by tuning the Fermi energy and carrier mobility of the graphene, respectively. Moreover, the refractive index of the cavity core, the susceptibility χ⁽³⁾ and the intensity of incident light have little effect on the GNR resonant modes, but have good tunability to the cavity resonant mode. The cavity length also has good tunability to the resonant mode of cavity. A strong interaction between the GNR resonant modes and the cavity resonant mode appears at a cavity length of L₁ = 350 nm. We also demonstrate the slow-light effect of this waveguide–cavity–graphene structure and an optical bistability effect in the plasmonic cavity mode by changing the intensity of the incident light. This waveguide–cavity–graphene structure can potentially be utilised to enhance optical confinement in graphene nano-integrated circuits for optical processing applications.