基于谐振腔增强型石墨烯光电探测器的设计及性能分析

提出了一种具有超薄有源层的谐振腔增强型石墨烯光电探测器的设计方法,利用谐振腔结构可以将光场限制在腔内,有效增强探测器的吸收.通过研究谐振腔内光场谐振条件及谐振模式下探测器响应度增强的机理,建立了驻波效应下谐振腔增强型石墨烯光电探测器光吸收模型,仿真分析谐振腔反射镜反射率、谐振腔腔长对于腔内光场增强器件性能的影响.理论分析表明,谐振腔增强型石墨烯光电探测器在850 nm处响应度可达0.5 A/W,相比无腔状态下提高了32倍;半高全宽为10 nm.采用谐振腔结构能够提高石墨烯光电探测器件的光电响应,为解决光电探测器响应度与响应速度之间的相互制约关系提供了途径.     

等离激元增强的石墨烯光吸收

石墨烯中等离激元具有特殊的光电性质,其和入射光的强烈耦合可以引起光吸收的增强.本文基于时域有限差分法和多体自洽场理论研究了等离激元对处于光学谐振腔中的石墨烯光吸收的影响.由于石墨烯中等离激元与入射光动量和能量不匹配而不能直接相互作用,因此石墨烯上施加了金属光栅结构.研究发现光栅结构能够对入射光进行动量补偿并且能够引起其下石墨烯中的电场强度产生很大程度增强,从而导致在该石墨烯结构中太赫兹等离激元和入射光发生强烈耦合而产生太赫兹等离极化激元,同时引起石墨烯光吸收的增强.希望本文能够加深对石墨烯光电特性的理解以及可以为基于石墨烯的太赫兹光电装置提供一定的理论依据.     

环形光子晶体光纤中涡旋光的传输特性研究

由于涡旋光具有轨道角动量,将它应用于光纤通信领域可以有效提高信息传输速率.设计了一种环形光子晶体光纤,利用COMSOL Multiphysics软件对其涡旋光TE01,HE±21和TM01模式特性进行模拟计算,它们之间有效折射率差分别为4.59×10~(-4)和3.62×10~(-4);其中,TE01模式的涡旋光在入射光波长范围为1650—1950 nm时,色散值在44.18—45.83 ps·nm~(-1)·km~(-1)之间平坦;入射光波长在1550 nm时,TE01模式的涡旋光的非线性系数为1.37 W~(-1)·km~(-1).该结构的光子晶体光纤的涡旋光具有损耗小、色散平坦等特性,对光纤中传输涡旋光、将涡旋光应用于超连续谱等方面的研究具有重要意义.     

All-optical switch based on photonic crystal microcavity with multi-resonant modes

We present a design of all-optical switches based on one-dimensional photonic crystals (1D PhC) doped with nonlinear optical materials. The 1D PhC switch structure is composed of a PhC cavity sandwiched by two accessional PhC microcavities. The center PhC cavity has two resonant frequencies with nearly the same quality factors (Q), while the accessional PhC cavities have the same resonant frequency, which is equal to one of the resonant frequencies of the center cavity. The two accessional PhC cavities cause reduction of Q value in this resonant frequency and result in different Q values of two modes. We realize all-optical switch effect by selecting pump light wavelength at the low Q mode and probe light wavelength at the other mode. The theoretical simulations by using the finite difference time domain method show that the pump light intensity required to realize optical switch effect in the designed switch is 50 times smaller than that in one-dimensional photonic crystals cavity with only one resonant mode.     

Ultra-compact graphene plasmonic filter integrated in a waveguide

Graphene plasmons have become promising candidates for deep-subwavelength nanoscale optical devices due to their strong field confinement and low damping. Among these nanoscale optical devices, band-pass filter for wavelength selection and noise filtering are key devices in an integrated optical circuit. However, plasmonic filters are still oversized because large resonant cavities are needed to perform frequency selection. Here, an ultra-compact filter integrated in a graphene plasmonic waveguide was designed, where a rectangular resonant cavity is inside a graphene nanoribbon waveguide. The properties of the filter were studied using the finite-difference time-domain method and demonstrated using the analytical model. The results demonstrate the band-pass filter has a high quality factor(20.36) and electrically tunable frequency response. The working frequency of the filter could also be tuned by modifying the cavity size. Our work provides a feasible structure for a graphene plasmonic nano-filter for future use in integrated optical circuits.     

基于导模共振效应提高石墨烯表面等离子体的局域特性

本文构建了一种包含石墨烯和亚波长光栅的复合结构, 借助衍射光栅的导模共振效应, 在石墨烯表面激发高局域性表面等离子体激元, 研究了石墨烯与光栅结构对表面等离子体激元局域特性的影响规律, 并借助基于有限元法的COMSOL软件, 分析了缓冲层厚度、光栅周期、载流子迁移率和费米能级对石墨烯的表面电场、品质因子Q和有效模式面积S_eff的影响. 结果表明, 石墨烯表面等离子体激元的局域性在特定的参数点获得显著提高: 当μ = 0.7 m²/(V·s)时, 品质因子达到最大值Q_max = 1793; 当p = 235 nm或E_F = 0.72 eV时, 表面电场达到了入射光的3000倍以上. 强烈的局域性导致强烈 的光-物质相互作用, 因而本文提出的复合结构可实现高灵敏度传感器和高效率的非线性光学设备, 极大地扩展了石墨烯在纳米光学领域中的应用.     

Optical multistability in 1D photonic crystals with nonlinear Thue–Morse structure

A 1D photonic crystal structure contains 16 layers, 8 common dielectric layers and 8 layers with nonlinear medium, with an arrangement similar to the 5th generation, Thue–Morse multilayer is presented. The properties of photonics band gap, field distribution and optical multistability are investigated. On the band gap, 5 resonant modes is observed. On the behavior of output intensity versus input intensity around resonant frequencies, the multistability response observed. When the frequency of incident field is close to the resonant frequency, the threshold intensity of multistability is decreased.     

石墨烯等离激元的光学性质及其应用前景

石墨烯等离激元由于其独特的电学可调性、本征低衰减以及局域光场高度增强等特性, 引起了广泛的关注并迅速成长为一门新的学科分支--石墨烯表面等离激元光子学. 本文介绍了石墨烯等离激元的一些基本性质, 包括色散关系、局域的等离激元和传导的等离激元以及石墨烯等离激元对其周边介电环境的敏感性等. 在此基础上, 进一步介绍了石墨烯等离激元在太赫兹到中红外频段的应用, 比如有源光调制器的一些功能器件和增强的红外光谱探测等.     

Controlled emission from dye saturated single and coupled microcavities

Modified photoluminescence is demonstrated from the dye saturated porous silicon based single and coupled microcavities. When photonic cavity mode is weakly coupled to the emission states of the dye, photoluminescence line narrowing and intensity enhancement have been observed. Our experimental work and transfer matrix simulations and cavity modelling convincingly explain the tunability and optical field confinement within the microcavity. We also show that the photoluminescence enhancement is due to one-dimensional microcavity effect. These optically active hybrid materials from inexpensive fabrication may become an important consideration for many photonic applications.     

利用窄刻槽金属光栅实现石墨烯双通道吸收增强

构建基底/窄刻槽金属光栅/覆盖层/石墨烯结构,利用金属光栅激发的表面等离子体激元共振和窄光栅刻槽支持的法布里-珀罗共振,在可见光波段实现单层石墨烯的双通道吸收增强,并结合简化模型估算出双吸收通道所在位置.在波长462和768 nm处,石墨烯的光吸收效率分别为35.6%和40.1%,相比石墨烯本征光吸收率的增强均超过15.5倍.进一步研究发现由于短波处吸收增强源于金属光栅的表面等离子体激元共振,其吸收特性受覆盖层厚度、刻槽深度和宽度变化的影响较小;而由于长波处吸收增强源于窄刻槽中的法布里-珀罗共振,因此呈现出良好的角度不敏感吸收特性.     

Synthesis of resonant cavities having continuum spectra by genetic algorithm

This paper proposes a novel method for generating continuum spectra with possible applications in WDM access networks. This new method would allow the development of a simple continuum laser structure with better performances in terms of cost and simplicity than those of present supercontinuum sources. In this aim, we will analyze the possibility to broaden the resonant modes of a Fabry–Perot cavity by operating only on the design of one of the cavity's Bragg mirrors. Firstly we considered the conditions which a Bragg grating must satisfy in order to broaden the resonant modes of a resonant cavity. Because an exact solution is not physical possible, the genetic algorithm is the best available tool for the design of such a grating. An active medium is then added inside the cavity and its behavior below threshold is simulated. The spectra thus simulated are continuum over 5–15 nm.     

Tracking spatial modes in nearly hemispherical microcavities

We measure experimentally the spatial intensity profiles and resonant frequencies of the transverse modes of nearly hemispherical microcavities with cavity length and mirror curvatures below 10 microm. These resonators possess axially symmetric Gauss-Laguerre-like modes, but do not display the frequency degeneracies typical of large-scale optical cavities. It is possible to interpret these results using a paraxial model of cavity propagation that includes nonparabolic optical elements.     

Trapping and observing single atoms in a blue-detuned intracavity dipole trap

A single atom strongly coupled to a cavity mode is stored by three-dimensional confinement in blue-detuned cavity modes of different longitudinal and transverse order. The vanishing light intensity at the trap center reduces the light shift of all atomic energy levels. This is exploited to detect a single atom by means of a dispersive measurement with 95% confidence in 10 micros, limited by the photon-detection efficiency. As the atom switches resonant cavity transmission into cavity reflection, the atom can be detected while scattering about one photon.     

Tunable resonant optical microcavities by self-assembled templating

Micrometer-scale optical cavities are produced by a combination of template sphere self-assembly and electrochemical growth. Transmission measurements of the tunable microcavities show sharp resonant modes with Q factors of >300 and 25-fold local enhancement of light intensity. The presence of transverse optical modes confirms the lateral confinement of photons. Calculations show that submicrometer mode volumes are feasible. The small mode volumes of these microcavities promise to lead to a wide range of applications. in microlasers, atom optics, quantum information, biophotonics, and single-molecule detection.     

Graphene based photonic crystal optical filter: Design and exploration of the tunability

Optical characteristics of two new graphene based photonic crystals are studied in detail. A structure containing alternating layers of graphene and SiO₂ slabs is considered as the ideal crystal. The dependency of the photonic band gaps (PBGs) to the dielectric layer thickness and the period number is explored at first step. Potential of the proposed crystal to be used as an optical filter is then investigated. Adding a nonlinear electro-optic polymer as a defect layer, the alterations of the optical features are inspected. Results show that the defect layer insertion causes a resonant mode inside the PBGs. However, the location of the defect layer inside the crystal is very effective on both the frequency and width of the resonant mode. Tunability of the optical features is probed by taking into account of the dependencies to the wave incident angle, graphene chemical potential and the applied external voltage to the defect layer.     

Optical bistability in defective photonic multilayers doped by graphene

We study the optical bistability (OB) in photonic multilayers doped by graphene sheets, stacking two Bragg reflectors with a defect layer between the reflectors. OB stems from the nonlinear effect of graphene, so the local field of defect mode (DM) could enhance the nonlinearity and reduce the thresholds of bistability. The structure achieves the tunability of bistability due to that the DM frequency and transmittance could be modulated by the chemical potential. Bistability thresholds and interval of the two stable states could be remarkably reduced by decreasing the chemical potential. A lager Bragg periodic number could increase the localizing of field, but the graphene loss may decrease the intensity of transmission light. We have concluded an appropriate periodic number to achieve OB. The study suggests that the tunable bistability of the structure could be used for all-optical switches in optical communication systems.     

Mode hopping in single-mode microchip Nd：YAG lasers induced by optical feedback

The mode hopping phenomenon induced by optical feedback in single-mode microchip Nd：YAG lasers is presented. With optical feedback, mode hopping strongly depends on two factors： the ratio of external cavity length to intra-cavity length, and initial gains of the two hopping modes, When external cavity length equals an integral multiple of intracavity length, there is almost no mode hopping. However, if the external cavity length does not equal an integral multiple of intra-cavity length, mode hopping occurs. The ratio of external cavity length to intra-cavity length determines the position of two-mode hopping, The initial gains of the two hopping modes determine the corresponding peak values and oscillating periods of them in the intensity modulation curves.     

Cavity resonant mode in a metal film perforated with two-dimensional triangular lattice hole arrays

The transmission property of metallic films with two-dimensional hole arrays is studied experimentally and numerically. For a triangular lattice subwavelength hole array in a 150 nm thick Ag film, both cavity resonance and planar surface modes are identified as the sources of enhanced optical transmissions. Semi-analytical models are developed for calculating the dispersion relation of the cavity resonant mode. They agree well with the experimental results and full-wave numerical calculations. Strong interaction between the cavity resonant mode and surface modes is also observed.     

Optical feedback in a Zeeman-birefringence HeNe laser and its application in ranging

The optical feedback characteristics in a Zeeman-birefringence HeNe laser have been studied systematically when the external cavity varies in a large range. The intensity variations of the two orthogonally polarized lights are observed during the laser cavity tuning in the dual frequency laser. When the external cavity length is an integral multiple of the laser cavity length, either polarized light's intensity modulation depth varies not obviously when the laser works in dual modes conditions or single mode condition. But when the external cavity length is far away from an integral multiple of the laser cavity length and the laser works in different dual modes conditions, polarized light's intensity modulation depth varies obviously. This characteristic can guide us to tune the laser to work in single mode condition to improve the sensitivity of the optical system when the system is used for a large displacement measurement. It can also be used for measuring the position of the target mirror. The theoretical analysis is in good agreement with experimental results.     

Role of stationary photon statistics in a high-Q cavity mode while it is exciting the active laser medium

It has been shown by Yu. M. Golubev, M. I. Kolobov, and I. V. Sokolov, Zh. éksp. Teor. Fiz. 111, 1579 (1997) [JETP 84, 864 (1997)], that when an optical cavity is excited by external radiation from a sub-Poisson laser the cavity mode may be in either a sub-Poisson or a Poisson stationary state. This is not important for a resonant medium which is excited into the upper laser level while interacting with this mode inside the cavity. The degree of regularity of the excitation will be identical to that of the initial light flux incident on the cavity, and this ultimately ensures the same sub-Poisson lasing as for strictly regular pumping of the resonant medium. Zh. éksp. Teor. Fiz. 113, 1223–1234 (April 1998)