一种基于级联半导体光放大器环镜的光串并转换器（英文）

为了实现高速光信号的降速处理,提出了一种基于级联半导体光放大器环镜(SLALOM)的光串并转换器,用于实现将高速串行光脉冲信号转换成低速并行光脉冲信号.该光串并转换器采用串联SLALOM组成,将前一级SLALOM的输出作为后一级SLALOM的输入;SLALOM之间的光传播时延为输入光信号比特周期;设置控制光与信号光脉冲时序,实现各级SLALOM光脉冲并行输出.通过采用1×10光串并转换器实现将80Gb/s串行信号转换为10路8Gb/s并行信号,并对控制、信号脉冲光功率和时间偏移量器件参量进行了优化.对于1×10光串并转换器,端口接收灵敏度差异小于10dB.该光串并转换器光功率损耗小、易于扩展并行端口数目,可用于光通信领域中的高速解复用、光信号处理和光交换系统中.     

基于光参量放大的高速实时光取样技术

提出了一种基于光参量放大的高速实时光取样方案. 利用色散介质对光纤锁模激光器产生的窄脉冲源进行色散展宽,从而产生线性啁啾光信号. 将该信号和被取样信号同时送入高非线性光纤,利用高非线性光纤中的参量放大效应,将被取样信号的强度信息调制到线性啁啾光信号上. 在接收端利用不同中心波长的滤波器即可滤出不同时间点的取样信号,从而在光域同时完成了高速实时光取样和取样信号的串-并转换. 是实现高速实时取样技术的一种极具竞争力的实现方案. 实验中,实现了对10 Gb/s非归零码OOK信号的40 GS/s的高速实时取样系统,并转换为4路10 GS/s取样信号输出. 在接收端成功根据4路取样信号恢复出被取样信号波形,验证了该实时光取样方案的可行性. 关键词： 光信号处理 光取样 参量放大 高非线性光纤     

基于谐波拟合产生周期性三角形光脉冲串的实验研究

实验研究了一种基于谐波拟合产生周期性三角形光脉冲串的方法,方案首先利用马赫曾德调制器的载波抑制调制,获得具有周期性起伏的连续光强度信号,然后利用光纤色散所致的射频功率衰落效应,对光强度表达式中四次谐波分量进行抑制,调节调制深度后,光强度表达式将向理想三角形傅里叶展开式的前三项进行逼近,最后以谐波拟合的方式获得重复频率为射频调制频率二倍的周期性三角形光脉冲串.结合实验,在9.862 GHz和7.678 GHz射频调制频率下,获得了脉冲重复频率19.724 Gb/s(脉冲全宽约50.7 ps)和15.356Gb/s(脉冲全宽约65.1 ps)的稳定三角形光脉冲串输出,改变色散量并反向调节调制频率,可进一步改变脉冲的重复频率,所获得的实验结果与理论预期基本符合.     

基于半导体光放大器四波混频效应的多种调制格式的波长转换实验

实验报道了利用半导体光放大器(SOA)的四波混频(FWM)效应实现多种码型的波长转换.其中对于非归零(NRZ)信号实现了从单信道到三信道的多波长转换.调制速率从10 Gb/s到40 Gb/s均实现多波长转换.对于归零(RZ)信号分别实现了20 Gb/s和40 Gb/s的RZ格式的波长转换和40 Gb/s的载波抑制归零(CSRZ)格式的波长转换,利用光纤布拉格光栅(FBG)作为带陷滤波器消除共轭光和抽运光之间的串扰.对于非归零差分相移键控(NRZ_DPSK)信号分别实现了20 Gb/s和40 Gb/s的波长转换,利用实验室自制的光纤延时干涉仪进行NRZ-DPSK信号的解调.基于FWM效应的转换光的输出消光比大于7 dB,转换后消光比退化约为3 dB.     

基于光纤中交叉相位调制的波长转换器研究

波长转换器在未来的全光网络中将起到重要的作用.通过大量的数值仿真,研究了利用色散位移光纤中的自相位调制效应的波长转换器,首次对各参量,包括输入光信号脉冲的峰值功率,连续波的功率,两束光信号的频率间隔,光纤的色散,光纤的长度以及输入信号的比特率对此波长转换器的性能影响进行了数值研究.结果表明,光纤的色散和输入光信号脉冲的功率在这种波长转换器中起重要作用,而且这种波长转换器可以对高达200Gb/s的信号进行转换.     

量子点半导体光放大器波长转换的Q因子特性

为了改善全光波长转换器的转换性能进而提高输出信号质量,研究了波长转换器的Q因子特性。采用牛顿迭代法和四阶龙格库塔法解光场传输方程和跃迁速率方程,分析了输入信号光功率、脉冲宽度、最大模式增益和有源区长度4个因素对全光波长转换器的Q因子特性的影响,并将得到的结果与相同条件下的输出消光比比较。结果表明:增大输入信号光功率,Q因子先增大后减小,并且在-12 d Bm时取得最大值8.819 d B;Q因子随着脉冲宽度的增加而不断下降;增大最大模式增益和有源区长度,Q因子增大。在实现波长转换的基础上,优化各参数数值,得到的Q因子达到16.680 d B,输出信号质量较好。要同时获得高的消光比和Q因子,提高输出信号的质量,必须选取适当的输入信号光功率、脉冲宽度、最大模式增益和有源区长度。     

利用非线性光纤环镜160Gb/s到10Gb/s解时分复用

研究了160 Gb/s光时分复用(OTDM)系统的解复用技术.针对160 Gb/s速率的特点,对高非线性光纤(HNLF)的光纤环镜(NOLM)特性及解复用进行了数值仿真.计算了低信号光时间抖动下解复用误码特性对时钟与信号的走离及时钟功率的依赖关系.计算了三种走离值消光比随时钟功率增加的变化趋势并给出:存在一个能获得最大的解复用窗口消光比、并能降低相邻信道串扰的合适的时钟功率范围.利用自制的基于电吸收调制器和压缩技术的超短光脉冲源建立了160 Gb/s OTDM实验系统,测量了不同信号光功率下NOLM的消光比,它基本不随信号增大而变化,在信号功率为7.3 dBm时仍大于23 dB.利用上述装置实现了无误码的160 Gb/s到10 Gb/s全光解复用.     

基于双半导体光放大器的读/写分别控制的新型全光缓存器

全光缓存器能够在光域内对数据包进行缓存,解决数据包在节点的冲突。提出了一种新型可擦写的全光缓存器,该缓存器以半导体光放大器(SOA)为非线性相移器件,利用信号光和控制光在半导体光放大器中的交叉相位调制实现信号在光域内的"写入"和"读出"。在注入信号峰值功率相同的条件下,双半导体光放大器结构的采用还可以对信号光实现功率补偿,比利用单个半导体光放大器进行"写入/读出"控制延长了缓存时间,并能有效克服在数据包"写入"缓存器时造成的输出端口处信号光的泄漏。该缓存器顺利实现了2.5 Gb/s数据包的多圈缓存。     

用于全光缓存的光阈值门理论和实验研究

提出了一种基于光阈值门的全光缓存方案,采用两个非对称的SOA环形腔激光器耦合构成光阈值门,其输出光可以在两种波长上切换,可控制波长转换器实现光包路由,从而将需缓存的数据包路由到缓存端口,避免了复杂的包头处理.建立了光阈值门的理论模型,对10 Gbit/s的光阈值门的动态特性进行了数值模拟和实验研究,实验结果和理论计算结果相符合,实验也表明光阈值门两种输出状态的消光比可达30dB.     

40 Gb/s信号全光3R再生实验

提出一种新型40 Gb/s全光3R再生器方案。采用高精细度法布里-珀罗滤波器进行时钟提取。时钟提取前,通过高稳定光源对输入信号光波长变换实现信号光波长和法布里-珀罗滤波器梳状窗口对准;时钟提取后,接半导体光放大器(SOA)进一步消除时钟信号噪声。全光判决中,采用双半导体光放大器串联增大非线性性能,提高了判决门的响应速度。判决输出接窄带滤波器去除脉冲啁啾拖尾,减小码型效应。实验中,恶化40 Gb/s光脉冲信号通过全光3R再生器可以得到再生脉冲。输入恶化信号时间抖动大于5 ps,脉冲宽度大于16 ps,再生得到的信号时间抖动小于1.5 ps。再生信号相对于输入信噪比改善14 dB。连续稳定工作记录大于15 h。通过实验验证,这种全光3R再生器方案成功地实现了40 Gb/s信号的再生。     

Controllable optical bistability and multistability in a rare-earth-ion-doped optical fiber

We investigated the optical bistability and multistability in an Er³⁺-doped ZrF₄–BaF₂–LaF₃–AlF₃–NaF optical fiber inside an optical ring cavity. It is found that the optical bistability and multistability can be easily controlled via adjusting properly the parameters of the corresponding system. Our scheme may provide some new possibilities for technological applications in optoelectronics and optical-fiber communication.     

A high nonlinearity elliptical fiber for applications in Raman and Brillouin sensors

Raman and Brillouin effects have found special applications in distributed sensing for smart materials and structures. In these sensors, the fiber acts as a distributed sensor, sensing strain and temperature over a range of tens of kilometers and, at the same time, carries this information to the installation that will process them. In order to optimize the fiber to operate under the Brillouin and Raman regimes, a special elliptical fiber with small effective area has been designed, which will allow these sensors to cover longer distances and/or employ lower power lasers.     

Optical arithmetic unit using bit-WDM

A novel arithmetic unit is proposed consisting of a pipelined optical ripple carry adder that adds two words with bits multiplexed by different wavelengths on a single fiber. The addition result is returned to a fiber bus in the same format as the incoming words. The corresponding operand bit pairs are split off the fiber using wavelength division demultiplexers. Full adders compute the sum for each bit pair and the carry from the next lower significant bit pair. The full adder uses couplers and NOT, NOR and novel XOR logic gates constructed using semiconductor optical amplifiers for gain and wavelength shifting.     

Demonstration of high extinction ratio modal interference in a two-mode fiber and its applications for all-fiber comb filter and high-temperature sensor

We show that high extinction ratio (>20 dB) modal interference in a two-mode dispersion compensating fiber can be utilized to build a compact, easy-to-fabricate tunable all-fiber optical comb filter. Wavelength tunability over the full free spectral range of the comb filter is demonstrated with an electrical power of 115mW using an on-fiber thin film micro-heater deposited directly on the fiber. In another configuration, the comb filter is used as a temperature sensor with dynamic range of >300 °C and sensitivity of <0.1 °C. The temperature sensor is capable of measuring a temperature as high as 500 °C.     

Experimental measurement and analysis of the optical trapping force acting on a yeast cell with a lensed optical fiber probe

Based on an optical trapping system with a single-lensed fiber probe inserted at an angle, the sub-picoNewton trapping force acting on a yeast cell as a function of the displacement is measured experimentally by the static and dynamic methods, respectively, whose measurement processes are presented in detail. The measured maximum trapping efficiency is 0.07 in our experiment, which is an order of magnitude lower than that of the optical tweezers. The characteristics of the trapping force in the various horizontal directions are discussed. Finally, the analysis of the measurement error shows the factors and their magnitude which cause error, and offers a way to reduce the error in future.     

Temperature dependence of low loss polymeric AWG

We investigate on the variation of loss and temperature dependence of a polymeric arrayed waveguide grating (AWG) depending on its substrate, by fabricating 16-channel polymeric AWGs with various substrate conditions. Insertion loss for a polymeric AWG on a silicon substrate is measured as low as 3.1 dB. The temperature-dependent wavelength shift for a polymeric AWG detached from the substrate is maintained within 0.1 nm from 20 to 80 °C. But we observe a degradation of insertion loss and a little instability in wavelength characteristics both for the detached polymeric AWG and for a polymeric AWG on a polymer substrate. We investigate on those optical properties of the polymeric AWGs based on measured thermal expansion properties of the polymers.     

Method of state code matrixes in the realization of optical switching using Perfect Shuffle

Based on the Left Perfect Shuffle (LPS) optical communication network constructed by cascade multi-stage LPS interconnection, using Looping algorithm, any arbitrary sequence of the input signals can be realized. However, instead of obtaining the simultaneous state codes of the same level node switches through mathematical analytical expressions directly, only routing tags of each channel can be obtained through mathematical analytical expressions so as to draw out topological chart of the network to obtain the state codes implied in the chart. Thus, the states of the switches cannot be directly programmed and controlled by computer in practical application. In this paper, based on the Looping algorithm, a method of stage code matrixes is presented to resolve this problem. By using the method, the simultaneous state codes of the same level’s four node switches can be directly obtained, which is convenient for the computer to provide controlled signals needed to finish the permutation for each node switch. The method of stage code matrixes provides further theoretical basis for the realization of optical switching by integration of Perfect Shuffle and high-speed optical switches.     

Dichroic property of the H2O-groups in α-quartz, LiNbO3 and LiTaO3 in the infrared range

The absorptive peaks of the H₂O-groups were observed in the infrared absorption spectra in the vicinity of 3480 cm⁻¹ in LiNbO₃ and LiTaO₃, and 3580 cm⁻¹ in α-quartz. The absorptions of these lines were found to depend on the vibration direction of the polarized incident light, showing the dichroic property in these crystals. The absorption of the ordinary ray waves is much larger than that for the E-ray waves in the crystals. This observation indicates that the direction of the bond vibrations for the H₂O-groups is perpendicular to the optic axis of crystals. The dichroic property of the H₂O-groups may serve as the tracer to study the local electric field in piezoelectric crystals.     

All optical latches using quantum-dot semiconductor optical amplifier

The design and performance of two optical latches, the Set-Reset (SR) latch and D-Flip-Flop has been studied. These latches are the building blocks of large optical processors. The latches are built using two optical logic operations NAND and NOT. Both NAND and NOT operations are realized by using Mach-Zhender interferometer (MZI) utilizing semiconductor optical amplifier with quantum dot active region (QD-SOA). Nonlinear dynamics including carrier heating and spectral hole-burning in the QD-SOA are taken into account together with the rate equations in order to realize the all-optical logic operations. Results show that this scheme can realize the functions of Set-Reset latch and D-Flip-Flop at high speeds (∼250 Gb/s). The dependence of the output quality (Q factor) on QD-SOA parameters is also discussed.     

Dispersion-Managed Solitons in Multiple-Core Nonlinear Fiber Arrays

The variational principle is employed to obtain the evolution of the parameters of Gaussian and super-Gaussian chirped solitons that propagates through multiple-core nonlinear optical fiber arrays. This is governed by the dispersion-managed nonlinear Schrodinger's equation with strong dispersion management in the presence of linear coupling between the adjacent cores. The results are valid for any configuration of the cores.