Synthesis and Curing Kinetics of UV-Curable Waterborne Bisphenol-S Epoxy-Acrylate/Polyurethane-Acrylate/Methylacryloylpropyl-POSS Nanocomposites

In order to prepare waterborne UV-curable polyurethane-acrylate (PUA) /epoxyl-acrylate (ERA) nanocomposites, the PUA, bisphenol-S epoxy acrylate (BPSEA) and methylacryloylpropyl polyhedral oligomeric silsesquioxanes (MAP-POSS) were synthesized. UV-curable BPSEA/PUA/MAP-POSS nanocomposites were prepared. The curing process, kinetics, and properties of the nanocomposites were investigated by Fourier transform infrared spectrometer (FTIR), differential scanning calorimeter (DSC) and dynamic mechanical analyzer (DMA). The base-acid resistance ability, adhesive strength, and hardness of coating films were determined. The results showed that these nanocomposites could be cured by both UV-light irradiation and a thermal free radical polymerization. Under the UV-light irradiation, they could be cured basically completely in about 20 min. The thermal free radical curing reaction could be described by a two-parameter autocatalytic ?esták-Berggren (S-B) model. The dynamic mechanical loss peak temperature, T_p, of the cured nanocomposites increased with increasing MAP-POSS content up to 8 wt%, an enhancement of 5.8°C over the pure BPSEA/PUA system, and then decreased. Films of the nanocomposites also had better base-acid resistance ability and hardness than pure BPSEA/PUA.     

Emulsion Polymerized Polystyrene/Montmorillonite Nanocomposite and its Viscoelastic Characteristics

A novel polystyrene (PS)/clay nanocomposite was synthesized using a simple emulsion polymerization method in the presence of sodium ion exchanged montmorillonite (Na‐MMT). Prior to the radical polymerization procedure with potassium persulfate (KPS) as an initiator, the hydrophobic styrene monomer was intercalated into hydrophilic clay layers using sodium dodecyl sulfate (SDS) as a surfactant. The FTIR spectra of the products showed the characteristic absorbance peaks of both the synthesized PS and Na‐MMT. The x‐ray diffraction patterns of the products exhibited an increase in the d ₀₀₁‐spacing, pointing to the intercalation of the PS chains into the intergalleries of the Na‐MMT. The enhancement of the thermal properties of the nanocomposite materials, such as the increase in the glass transition temperature of the PS, was investigated by differential scanning calorimetry (DSC). Furthermore, based on the viscoelastic properties of the products examined using a rotational rheometer with a parallel plate geometry, the nanocomposites were found to exhibit more rapid shear thinning and increased storage (G′) and loss (G″) moduli with increasing clay content.     

纳米铝粉/聚苯乙烯包覆粒子的制备及表征

利用超声波的分散和粉碎作用,对纳米Al粒子进行了表面疏水处理。然后,以无水乙醇为反应介质,苯乙烯为单体,偶氮二异丁腈为引发剂,聚乙烯吡咯烷酮为分散剂,在氮气保护环境下,利用超声波的活化和引发作用,引发苯乙烯单体在纳米Al粒子表面进行分散聚合反应,制备出了纳米铝粉/聚苯乙烯包覆粒子。最后,运用多种测试手段对纳米Al/PS包覆粒子形貌、粒径大小及分布、表面特性、化学组成及结构等进行了表征。测试结果表明,所制备的纳米Al/PS包覆粒子已经形成了完整的球型核壳包覆结构,表面完整无缺陷,粒径大小约为2.0 m。     

Preparation of Halloysite Nanotubes/Polystyrene (HNTs/PS) Core‐shell Particles via Soap‐less Microemulsion Polymerization

Halloysite nanotubes/polystyrene (HNTs/PS) inorganic/organic core‐shell particles were prepared via a convenient soap‐less microemulsion polymerization. The inorganic cores were pre‐treated with allyl alcohol (AA) and the polymer shells were prepared successfully by the facile soap‐less microemulsion polymerization of styrene (St) with the allyl alcohol‐modified halloysite nanotube (AA‐HNT) nanoparticles as seeds, and potassium persulfate (KPS) as initiator in water. The products were characterized by Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). The morphologies of the HNTs/PS core‐shell particles were characterized by transmission electron microscopy (TEM). The mechanism of the nucleation is also mentioned.     

Natural rubber nanocomposites using polystyrene-encapsulated nanosilica prepared by differential microemulsion polymerization

In this study, nanocomposites of natural rubber (NR) and polystyrene (PS)-encapsulated nanosilica were prepared by latex compounding method. The nanolatex of PS-encapsulated silica was synthesized via in situ differential microemulsion polymerization. The resulted hybrid nanoparticles showed core-shell morphology with an average diameter of 40 nm. The silica hybrid nanoparticles were subsequently used as filler for the NR nanocomposite. The properties of NR were found to be improved as a result of the incorporation of PS-encapsulated nanosilica at 3 and 3-9 parts per hundred rubber (phr) for tensile strength and modulus at 300% strain, respectively, except the elongation at break, and up to 9 phr for flammability. The results from dynamic mechanical analyzer showed that the elastic properties of NR near the glass transition temperature increased with the inclusion of increasing concentration of the PS-encapsulated nanosilica, causing by the semi-interpenetrating nanostructure in the NR nanocomposites.     

Polycyanurate–Organically Modified Montmorillonite Nanocomposites: Structure–Dynamics–Properties Relationships

Polycyanurate‐modified montmorrilonite (PCN‐MMT) nanocomposites were synthesized by polymerization of dicyanate ester of bisphenol A in the presence of MMT dispersed by ultrasound. Techniques of IR spectroscopy, WAXD, and TEM were applied to study polymerization kinetics and structure of the nanocomposites prepared, whereas their dynamics and thermal/mechanical properties over the ?30 to 420°C range were studied by using DSC, laser‐interferometric creep rate spectroscopy (CRS), and dielectric relaxation spectroscopy (DRS) techniques. It was shown that a small amount of MMT additive acts as a catalyst of polymerization and results in the formation of complicated intercalated/exfoliated structures, as well as strongly modifies the dynamics in the PCN network. Pronounced dynamic heterogeneity was observed for PCN/MMT nanocomposites. Along with the main PCN glass transition, two new glass transitions, at much higher and much lower temperatures, were revealed as a consequence of constrained dynamics in matrix interfacial nanolayers and due to incomplete local cross‐linking in the PCN matrix, respectively. In addition, increased sub‐T _g mobility was observed in these nanocomposites. A two‐fold rise of modulus of elasticity as well as increasing thermal stability and arising microplasticity at low temperatures, promoting, obviously, improved crack resistance in a brittle PCN network, were found for the PCN‐MMT nanocomposites.     

Synthesis and microwave absorption properties of graphene-oxide(GO)/polyaniline nanocomposite with Fe3O4 particles

In order to investigate the impedance matching properties of microwave absorbers,the ternary nanocomposites of GO/PANI/Fe₃O₄（GPF） are prepared via a two-step method,GO/PANI composites are synthesized by dilute polymerization in the presence of aniline monomer and GO,and GO/PANI/Fe₃O₄ is prepared via a co-precipitation method.The obtained nanocomposites are characterized by scanning electron microscopy（SEM）,X-ray diffraction（XRD）,and Fourier transform infrared spectroscopy（FTIR）,respectively.The microwave absorbability reveals enhanced microwave absorption properties compared with GO,PANI,and GO/PANI.The maximum reflection loss of GO/PANI/Fe₃O₄ is up to-27 dB at 14 GHz with its thickness being 2 mm,and its absorption bandwidths exceeding-10 dB are more than 11.2 GHz with its thickness values being in the range from 1.5 mm-4 mm.It provides that GO/PANI/Fe₃O₄ can be used as an attractive candidate for microwave absorbers.     

In situ synthesis and characterization of LiNi0.5La0.08Fe1.92O4-polyaniline core-shell nanocomposites

Core-shell-structured LiNi_0.5La_0.08Fe_1.92O₄-polyaniline (PANI) nanocomposites with magnetic behavior were synthesized by in situ polymerization of aniline in the presence of LiNi_0.5La_0.08Fe_1.92O₄ nanoparticles. The structure, morphology and magnetic properties of samples were characterized by powder X-ray diffraction (XRD), Fourier transform infrared (FTIR), UV-vis absorption, transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM) technique. The results of spectroanalysis indicated that there was interaction between PANI chains and ferrite particles. TEM study showed that LiNi_0.5La_0.08Fe_1.92O₄-PANI nanocomposites presented a core-shell structure with a magnetic core of 30-50 nm diameter and an amorphous shell of 10-20 nm thickness. The nanocomposites under applied magnetic field exhibited the hysteresis loops of the ferromagnetic nature. The saturation magnetization and coercivity of nanocomposites decreased with decreasing content of LiNi_0.5La_0.08Fe_1.92O₄. The polymerization mechanism and bonding interaction in the nanocomposites have been discussed.     

聚甲基丙烯酸甲酯/镓纳米复合物的动力学弛豫行为

通过原位自由基聚合方法制备了聚甲基丙烯酸甲酯(PMMA)以及含镓(Ga)质量分数为11.3%和13.5%的PMMA/Ga纳米复合材料.在玻璃化转变温度及以上温区,利用能量耗散技术研究PMMA/Ga纳米复合物的动力学弛豫行为,发现随着Ga含量的增加,复合物的α弛豫峰移向高温但峰高降低.此外,还定量研究了Ga含量对PMMA/Ga复合物的α' 弛豫的影响,并作出了相应的解释. 关键词： 相对能量耗散 玻璃化转变 力学弛豫     

Investigation on thermal conductivity and physical properties of polythiophene/p-phenylenediamine-graphene oxide and polythiophene-co-poly(methyl methacrylate)/p-phenylenediamine graphene oxide composites

An efficient approach was employed to simultaneously functionalize and reduce the graphene oxide (GO) with p-phenylene diamine (PPD) using simple refluxing. There was a possibility of nucleophilic substitution of amino moieties of PPD with the epoxy groups of GO. The polythiophene (PTh) and polythiophene-co-poly(methylmethacrylate) (PTh-co-PMMA) nanocomposites with chemically modified GO were prepared using in situ polymerization technique. Two series of nanocomposites that is PTh/PPD-GO and PTh-co-PMMA/PPD-GO were designed. The nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction, scanning electron microscopy (SEM), thermal conductivity, and electrical conductivity measurement. The FTIR spectra depicted the characteristic absorption peaks for the formation of copolymer and their composites with PPD-GO. The SEM micrographs showed that the PPD-GO nanosheets were homogeneously dispersed in copolymer matrix forming nano-granular morphology. The nanofluids were prepared by suspending modified GO particles inside the basefluid of polythiophene and PTh-co-PMMA. The thermal conductivity of nanocomposites was significantly improved even with low PPD-GO loading. The thermal conductivity of PTh-co-PMMA/PPD-GO with 1.5 wt.% filler was increased to 1.42 W/mK at a higher temperature. The XRD patterns confirmed the presence of chemical interactions between the copolymer and filler particles. The electrical conductivity of PTh-co-PMMA/PPD-GO was also found to increase in the range of 6.1 × 10^?3–2.5 × 10^?2 S/cm. Novel PTh-co-PMMA/PPD-GO-based nanocomposite is potentially significant in high-performance thermal systems.     

Preparation of conductive nanocomposites based on poly (aniline-co- butyl 3-aminobenzoate) and poly (aniline-co-ethyl 3-aminobenzoate) by solution blending method

The polyaniline (PANI) is a widely studied conducting polymer due to its application in several devices such as biosensor, gas sensor etc. Known methods to produce PANI composites may be essentially reduced to two distinct groups: synthetic methods based on aniline polymerization in the presence of or inside a matrix polymer, and blending methods to mix a previously prepared PANI with a matrix polymer. Poly (aniline-co-butyl 3-aminobenzoate) (ANI-co-BAB) and poly (aniline-co-ethyl 3-aminobenzoate) (ANI-co-EAB) are prepared as conducting copolymers in nanoscale by chemical oxidation method under ultrasonic irradiation. The different molar ratio of aniline to butyl 3-aminobenzoate and ethyl 3-aminobenzoate are used in the preparation of copolymers. Conductive nanocomposites based on ANI-co-BAB or ANI-co-EAB with poly (styrene-alt-maleic acid) (PSMAC), and polystyrene are prepared by solution blending method. The obtained conductive composites formed films with good homogeneity and flexibility. The conductivity of the obtained nanocomposites is measured with a four-probe method. The electrical conductivity of the composites (ANI-co-EAB)/PSMAC/PS and (ANI-co-BAB)/PSMAC/PS are 24?×?10^?5?S?cm^?1 and 31?×?10^?5?S?cm, respectively. Our results show that the (ANI-co-BAB)/PSMAC/PS composite has more conductivity than (ANI-co-EAB)/PSMAC/PS composite. The copolymers and composites in nanoscale are characterized by FT-IR and ¹H NMR spectral data. The surface morphology was studied using SEM analysis. Also, their grain size is measured using XRD studies.     

原位聚合纳米Ni/聚苯乙烯复合材料及其热力学性能

 磁性聚苯乙烯(PS)材料有利于实现惯性约束聚变靶丸在辐射场中的无接触支撑。采用液相还原法制备了粒度为75~200 nm的Ni球形粒子,用原位聚合的方法制备了纳米Ni/PS复合材料。利用X射线衍射仪、傅氏转换红外线光谱分析仪、扫描电子显微镜及热重差示扫描量热仪分别研究了所得纳米Ni的特性、复合材料的结构及掺杂量对纳米Ni/PS复合材料的热力学行为的影响。研究结果表明：纳米Ni的掺杂能提高玻璃转变温度;纳米Ni的掺杂可以增大PS热分解焓变,在掺杂质量分数为1%~2%之间焓变达到最大;纳米Ni的掺杂降低了纳米Ni/PS复合材料热分解的比热容。     

Fabrication and Characterization of Polyethylene Nanocomposite Films Containing Zinc Oxide (ZnO) Nanoparticles Synthesized by a Cost-Effective and Safe Method

ZnO nanoparticles were synthesized through a cost-effective and safe method followed by fabrication and characterization of polyethylene/ZnO nanocomposite films and investigation of their properties. The morphology and size of the synthesized nanoparticles were evaluated by field emission scanning electron microscopy (FE-SEM). It was found that nanoparticles with a plate-like morphology with an average thickness of 50-70?nm were synthesized. The nanocomposites were characterized by using Fourier transform infrared analysis (FTIR) and ultraviolet–visible spectroscopy (UV-VIS). In addition, the effects of the amount of zinc oxide nanoparticles (ZnO-NPs) on the mechanical properties of the films and particles and their antibacterial properties against a gram-negative bacterium (Escherichia coli) and gram-positive bacteria (Staphylococcus aureus) were investigated. In the case of nanoparticles, one more gram-positive bacterium (Staphylococcus aureus) was studied. The results demonstrated an inhibition of growth of all bacteria in a broth medium for both the nanoparticles and nanocomposites. The FE-SEM micrographs revealed that by increasing the nanofiller content an inferior quality of dispersion was obtained which was reflected in the lower tensile strength of the nanocomposites compared to the pure PE. It was demonstrated that the addition of poly ethylene graft maleic anhydride (PE-g-MA), as compatibiliser, improved the dispersion state of the nanoparticles and, consequently, the ultimate mechanical properties. In addition, it was shown that the fabricated nanocomposites exhibited considerable UV-shielding properties.     

The Effect of Structure of the Clay Modifier on the Morphology and Properties of Polystyrene/Clay Nanocomposites Prepared via In Situ Suspension Polymerization

Polystyrene (PS)/organoclay nanocomposites were prepared via free radical suspension polymerization. Two kinds of organoclay were used, labeled KT and KD, modified by trimethyloctadecyl ammonium (TM) and dimethyldioctadecyl ammonium (DM) ions, respectively. Nanocomposites containing various amounts of both of the organoclay nanoparticles (1, 3, and 5 wt%) were prepared. The wide angle X-ray diffraction (WAXD) results revealed intercalation in both of the nanocomposites. The greatest improvement in thermal stability of the nanocomposites was achieved with 5 wt% of organo-MMT for both of the clays. The nanocomposite containing 3 wt% of KT organo-MMT showed the greatest improvement of storage modulus. When the organoclay content exceeded 3 wt%, the storage moduli decreased compared to the nanocomposite filled with 3 wt% of the organoclay. D-spacing calculations using Bragg's law and WAXD data showed that the KT and KD nanoparticles were intercalated within the PS matrix, but with different extents of intercalation. The styrene conversions of the as-polymerized nanocomposite samples were obtained by a gravimetric method. The results showed that conversion decreased with incorporation of organoclay in the reaction recipe. Particle size was also increased by increasing nanoclay content.     

Synthesis and characterization of polyurethane/SiO2 nanocomposites

In order to achieve good dispersion of nano-SiO₂ and increase the interactions between nano-SiO₂ and PU matrix, nano-SiO₂ was firstly modified with poly(propylene glycol) phosphate ester (PPG-P) which was a new polymeric surfactant synthesized through the esterification of poly(propylene glycol) (PPG) and polyphosphoric acid (PPA). Then a series of polyurethane (PU)/SiO₂ nanocomposites were prepared via in situ polymerization. The surface modification of nano-SiO₂, the microstructure and the properties of nanocomposites were investigated by FTIR, SEM, XRD and TGA. It was found that good dispersion of nano-SiO₂ achieved in PU/SiO₂ nanocomposite after the modification with PPG-P. The segmented structures of PU were not interfered by the presence of nano-SiO₂ in these nanocomposites.     

The effects of organoclay on the morphology and mechanical properties of PAI/clay nanocomposites coatings prepared by the ultrasonication assisted process

In this research, solvent based polyamide – imide (PAI)/clay nanocomposites were prepared successfully using the solution dispersion technique. With the assistance of the ultrasonic wave, the effect of the ultrasonic wave time on the microstructure of 3 wt% PAI/C20A nanocomposite (NC) was investigated. Then, the best ultrasonic parameters were selected and the effects of the concentration of Cloisite 20A (C20A) (1, 3 and 5 wt% C20A) on the microstructure and mechanical properties (adhesion, hardness, flexibility, wear and impact) of NCs were investigated. The PAI, C20A and nanocomposites (NC)s were characterized by Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray analysis (EDX), and Wide-angle X-ray diffraction (WAXD). The results showed that the sample with 1 and 3 wt% C20A had better mechanical properties, as compared to the pure PAI and the 5 wt% NC.     

Synthesis of Fe3O4/CNTs magnetic nanocomposites at the liquid-liquid interface using oleate as surfactant and reactant

Carbon nanotubes (CNTs)-based magnetic nanocomposites have attracted significant research interest owing to their great potentialities in various technological fields. In this investigation, a kind of novel Fe₃O₄/CNTs magnetic nanocomposites were prepared by in situ chemical precipitation using oleate as reactant and surfactant at the liquid-liquid interface of cyclohexane/ethanol/water mixture solvent. The as-prepared samples were characterized via transmission electron microscopy (TEM), X-ray diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR) and vibration sample magnetometry (VSM). Results indicated that the Fe₃O₄/CNTs magnetic nanocomposites dispersed well in organic medium were prepared organic medium, were prepared. The magnetic nanocomposites were proved to be superparamagnetic with coercive force of 3.69 Oe. A mechanism scheme was proposed to illustrate the formation process of the magnetic nanocomposites.     

Evaluation of an alternative modification route for layered silicates and synthesis of poly(styrene) layered silicate nanocomposites by in-situ suspension polymerisation

The organically modified montmorillonites (o-MMT) used in this study were prepared in a semi-solid state in molten long chain alkyl (hydrogenated tallow (HT) or stearyl) dimethyl/aryl ammonium chloride intercalant (quat), within a Brabender Plasticorder W50E chamber. The effect of quat level and structure was investigated using WAXS, FTIR (DRIFTS) and solvent swelling/dispersion viscosity studies. It was found that mono-stearyl (or HT) quats were the most suitable intercalants for the in-situ polymerised PS matrix nanocomposites produced. The distearyl (or HT) quats generally led to reduced interfacial effects in the composites and reduced toluene dispersion viscosity due to the close proximity of long alkyl tails within the molecules facilitating their self-assembly into ordered arrays, which were difficult for toluene to penetrate (toluene was used as a probe to gauge compatibility with styrene). Substitution of a benzyl group (for a methyl) led to increased compatibility with styrene/toluene, though the detrimental effect of two long alkyl groups was not overcome. PS matrix nanocomposites have been formed via in-situ free radical suspension polymerisation of styrene/organo-montmorillonite (o-MMT) dispersions. These composites displayed evidence of large interfacial area relative to the volume fraction of montorillonite added; this was manifested as a reduction in melt flow rate, broadening of the molar mass distribution (increase in M _w) and an increase in thermal stability, relative to the unfilled matrix. However, wide angle X-ray scattering (WAXS) patterns of the composites revealed a strong (001) reflection (d = 3.3–3.4 nm) together with clear (002) and (003) reflections. Therefore a mixed intercalated/flocculated morphology, with no significant exfoliation into single platelets, was indicated.     

Zinc-chromium layered double hydroxides anchored on carbon nanotube and biochar for ultrasound-assisted photocatalysis of rifampicin

In this study, ZnCr layered double hydroxide (LDH), ZnCr LDH/carbon nanotube (CNT), and ZnCr LDH/Biochar (BC) were synthesized and characterized by various analyses. The successful synthesis and the great crystallinity of the samples were consented by XRD analysis. SEM and TEM were applied to study the morphology of the synthesized samples. The simultaneous presence of C, Zn, and Cr elements was well confirmed by EDX and dot mapping analyses demonstrating the successful preparation of nanocomposites. According to the BET analysis, ZnCr LDH nanocomposites with BC and CNT had more specific surface area compared to ZnCr LDH alone. The catalytic performances of the samples were determined for the degradation of rifampicin (RF). The degradation efficiency of the sonophotocatalytic process in the presence of 0.6 g L⁻¹ of ZnCr LDH/BC toward 15 mg L⁻¹ of RF under 150 W ultrasound and visible light irradiation was found to be about 100% within 40 min. The influence of the reactive species on the sonophotocatalytic process was assessed via the addition of different scavengers (para-benzoquinone (p-BQ), formic acid (FA), isopropyl alcohol (IPA)), and enhancers (hydrogen peroxide and potassium persulfate). The GC–MS analysis was carried out and eleven by-products during the RF decomposition were detected.     

Structure and Properties of a cis-1,4-Polybutadiene/Organic Montmorillonite Nanocomposite Prepared via In Situ Polymerization

Cis-1,4-polybutadiene (cis-1,4-PB) is one of the most important synthetic rubbers, having superior performances such as wear resistance, cold resistance and high elasticity. However, its mechanical properties, including low tensile strength, tear resistance and thermal stability, limit its application in comparison to natural rubber and butadiene-styrene rubber that have excellent overall performances. Thus, the reinforcing of cis-1,4-PB is a necessity. The dispersion of clay in rubbers on the nanoscale can improve the mechanical, gas permeability and thermal properties of the resulting composites. In this paper, organic montmorillonite (OMMT) clay was dispersed into the cis-1,4-PB matrix via an in-situ polymerization method and the chemical structure, phase morphology, mechanical properties and thermal stability of the composite were investigated. The properties of the composite were analyzed by such techniques as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and thermal gravimetric analysis (TGA). In the in-situ polymerization, a Ni-based catalyst system with the presence of OMMT showed high efficiency and 1,4-selectivity for the polymerization of butadiene. The OMMT could be dispersed in the polymeric matrix on the nanoscale during the polymerization. The interfusion of OMMT had little influence on the thermal stability and the chemical micro-structure of the cis-1,4-PB when the content of cis-1,4 units was more than 95%. The loss tangent of the composite was higher than that of cis-1,4-PB from ?110 to ?55°C, the temperature range examined, and the mechanical properties of the cis-1,4-PB/OMMT nanocomposite (NC) were improved upon the addition of OMMT.