基于多目标遗传算法的增程式电动汽车动力系统参数匹配优化研究

在完成增程式电动汽车（E-REV）动力匹配与性能仿真基础上,针对E-REV动力系统参数匹配优化问题,以整车制造成本、汽车两种运行模式下等效百公里油耗以及百公里加速时间为目标,以驱动电机峰值功率、发动机额定功率以及电池能量为变量,设计了基于线性加权的多目标遗传算法。结果表明,适当牺牲汽车动力性可最大降低制造成本5.19%,并降低等效油耗9.61%以上。可以得出,通过改善匹配方案能进一步提高整车的动力经济性并降低制造成本,研究对E-REV市场推广及量产化具有重要意义。     

高功率密度电容器充电电源

针对高压脉冲电容器充电电源高功率小型化的发展需求,采用谐振软开关技术和热设计技术研制了开关频率为50 kHz的充电电源,要求在电源10 kV的额定输出电压下充电速率达到20 kJ/s（额定输出电压下峰值功率40 kW）,功率密度达到2 MW/m3。分析了分布参数的存在对高频逆变器工作特性的影响,介绍了针对不同分布参数影响的应对措施。初步试验研究了间歇工况下高功率小型化电源热设计技术,基于电源间歇工作特点,结合不同电源组件发热特性,设计了不同的散热措施,给出了各器件的温升数据。完成了充电电源性能测试实验,实验结果表明:电源功率密度达到2.15 MW/m3。     

用于FED和PDP平板显示高压驱动电路的CMOS器件

在Synopsys TCAD软件环境下,结合中国科学院微电子研究所0.8μm标准CMOS工艺条件对于高压CMOS器件进行了工艺和器件模拟。由于考虑到与标准CMOS工艺的兼容性,高压CMOS器件均采用LDMOS结构;根据RESURF技术,对于器件的漂移区进行了优化。器件模拟结果表明,高压NMOS器件源漏击穿电压为220 V;阈值电压和驱动能力分别为0.8 V和1×10-4A/μm。高压PMOS器件源漏击穿电压为-135 V;阈值电压和驱动能力分别为-9.7 V和1.8×10-4A/μm。高压CMOS器件的研制可为进一步研制FED和PDP平板显示高压驱动电路奠定基础。     

超大容量圆柱形单体400A·h锂离子电池投产

随着国内外汽车厂家全电动汽车在今春北京第十一届国际车展上集体亮相,“新能源汽车元年”悄然揭开了时代的序幕．日前天津大学和北京天路能源有限公司通过产学研合作,探索了电动汽车动力供给、安全稳定与绿色环保之间完美结合的新途径,开发的超大容量圆柱形单体400A·h“巨无霸”锂离子电池在全球锐开先河,成功投入小批量生产．该产品具有超高容量、安全性好、     

基于模糊控制算法的纯电动汽车空调控制器的研发

纯电动汽车迅速发展,要求其空调系统也急需跟进。根据纯电动汽车特点,开发出一种纯电动汽车空调控制器系统,设计了空调控制器的电源模块,阐述了使用无位置传感器控制压缩机无刷直流电机的原理,研发了一种过流检测电路。提出了一种新型控制方法,即：在考虑整车负载的基础上,使用多输入变量模糊控制算法对汽车空调压缩机电机进行控制,同时兼顾了乘员的舒适性与汽车的动力性。结果表明这种空调控制器运行良好,达到了预期效果。     

电动汽车与锂离子电池

文章简要介绍了混合动力汽车、插电式混合动力汽车、纯电动汽车和锂离子动力电池及其关键材料。发展电动汽车可以大幅度降低人们对石油的依赖和改善城市空气质量。锂离子电池性能优越,为电动汽车的发展提供了支撑。近期,新一代锂离子动力电池正极材料即将走向应用,可使电动汽车里程增加一倍,材料选择和电池设计及制造工艺与电池储存能量、寿命、安全等密切相关,尊道而重德,可做出“好”电池。     

纯电动汽车磷酸铁锂电池组的建模及优化

鉴于传统神经网络和支持向量机机理复杂、计算量大的缺陷,很难实时跟踪磷酸铁锂电池组复杂快速的内部反应,影响电池荷电状态的估算精度,提出应用一种简单、有效的极限学习机对一额定容量为100Ah、额定电压为72V的纯电动汽车磷酸铁锂电池组建模,并分别与BP神经网络、RBF神经网络、支持向量机进行对比。随后,以学习时间和泛化性能为优化目标,应用粒子群方法寻找最佳隐层节点个数。结果表明,基于极限学习机的磷酸铁锂电池组模型的学习时间、泛化性能优于BP神经网络、RBF神经网络、支持向量机;隐层节点优化后,模型的学习时间和泛化性能达到最优。     

具有半绝缘多晶硅完全三维超结横向功率器件

为了突破传统LDMOS (lateral double-diffused MOSFET)器件击穿电压与比导通电阻的硅极限的2.5 次方关系, 降低LDMOS器件的功率损耗, 提高功率集成电路的功率驱动能力, 提出了一种具有半绝缘多晶硅SIPOS (semi-insulating poly silicon)覆盖的完全3 D-RESURF (three-dimensional reduced surface field)新型Super Junction-LDMOS结构(SIPOS SJ-LDMOS). 这种结构利用SIPOS的电场调制作用使SJ-LDMOS的表面电场分布均匀, 将器件单位长度的耐压量提高到19.4 V/μupm; 覆盖于漂移区表面的SIPOS使SJ-LDMOS沿三维方向均受到电场调制, 实现了LDMOS的完全3 D-RESURF效应, 使更高浓度的漂移区完全耗尽而达到高的击穿电压; 当器件开态工作时, 覆盖于薄场氧化层表面的SIPOS的电场作用使SJ-LDMOS的漂移区表面形成多数载流子积累, 器件比导通电阻降低. 利用器件仿真软件ISE分析获得, 当SIPOS SJ-LDMOS的击穿电压为388 V时, 比导通电阻为20.87 mΩ·cm², 相同结构参数条件下, N-buffer SJ-LDMOS的击穿电压为287 V, 比导通电阻为31.14 mΩ·cm²; 一般SJ-LDMOS 的击穿电压仅为180 V, 比导通电阻为71.82 mΩ·cm².     

直流电场作用下生物柴油液滴的雾化特性和燃烧特性研究

设计搭建了电场作用下燃油液滴燃烧实验装置,对比了不同电压下生物柴油液滴的形态演变、变形程度、子液滴等行为,分析了不同电压下液滴火焰形貌演变、火焰尺寸等燃烧特性及最高液滴温度变化。结果表明,电压为3 k V和4 k V的电场会诱发生物柴油液滴产生锥射流,其破碎生成子液滴,尺寸范围为20～120μm,速度基本低于2.5 m·s^-1;受电场对火焰和液滴的综合影响,火焰变化主要表现为高度减小、宽度增大,纵横比减小;电压为1 k V和2 k V的电场降低了最高液滴温度,而当电压增加至3 k V和4 k V时最高液滴温度增加。     

高探测效率CMOS单光子雪崩二极管器件

基于标准0.35μm CMOS工艺设计了一种单光子雪崩二极管器件.采用p+n阱型二极管结构,同时引进保护环与深n阱结构以提高单光子雪崩二极管性能;研究了扩散n阱保护环宽度对雪崩击穿特性的影响;对器件的电场分布、击穿特性、光子探测效率、频率响应等特性进行了分析.仿真结果表明:所设计的单光子雪崩二极管器件结构直径为10μm,扩散n阱保护环宽度为1μm时,雪崩击穿电压为13.2 V,3 dB带宽可达1.6 GHz;过偏压为1 V、2 V时最大探测效率分别高达52%和55%;在波长500~800 nm之间器件响应度较好,波长为680 nm时单位响应度峰值高达0.45 A/W.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.