飞秒激光脉冲在高非线性光子晶体光纤中产生超连续谱的实验研究

使用钛宝石激光器抽运一根长1m的高非线性光子晶体光纤,获得的超连续谱波长覆盖范围为420—1700nm,输出功率为170mW,转换效率在20%以上;对实验结果给出了详细的分析,并与理论模拟结果相比较,认为超连续谱产生的主要原因是高阶孤子的分裂和四波混频效应.同时研究了不同抽运功率和不同抽运波长下超连续谱产生的情况,发现对同一根光纤,抽运功率由小到大变化时,可将输出的光谱分为初始展宽,剧烈展宽和饱和展宽三个阶段,当输出的光谱处于初始展宽和饱和展宽阶段时,都会存在一定的抽运残留,当输出的光谱处于剧烈展宽时,转 关键词： 光子晶体光纤 超连续谱 高阶孤子 反常色散区     

飞秒激光脉冲在高非线性光子晶体光纤中产生超连续谱的实验研究

使用钛宝石激光器抽运一根长1m的高非线性光子晶体光纤，获得的超连续谱波长覆盖范围为420—1700nm，输出功率为170mW，转换效率在20%以上；对实验结果给出了详细的分析，并与理论模拟结果相比较，认为超连续谱产生的主要原因是高阶孤子的分裂和四波混频效应.同时研究了不同抽运功率和不同抽运波长下超连续谱产生的情况，发现对同一根光纤，抽运功率由小到大变化时，可将输出的光谱分为初始展宽，剧烈展宽和饱和展宽三个阶段，当输出的光谱处于初始展宽和饱和展宽阶段时，都会存在一定的抽运残留，当输出的光谱处于剧烈展宽时，转     

高非线性光子晶体光纤中飞秒脉冲的传输特性和超连续谱产生机制的实验研究及模拟分析

用实验和数值模拟两种方法研究了高非线性光子晶体光纤中飞秒激光脉冲的传输特性和超连续谱的产生机理，给出了抽运脉冲在三种不同中心波长情况下输出光谱展宽并形成超连续谱的实际测量及理论模拟结果.研究表明：在零色散波长抽运时，光谱展宽以自相位调制为主，同时三阶色散的影响明显，传输脉冲在时域内出现振荡次峰.而在反常色散区抽运时，光谱展宽的初期以自相位调制为主，随后根据抽运功率的不同孤子自频移、高阶光孤子的裂变和四波混频效应会逐渐增强，进而成为光谱展宽的主要原因.与此相应，在时域中能明显看到孤子的形成和红移，飞秒传输脉 关键词： 光子晶体光纤 高非线性光子晶体光纤 飞秒脉冲激光 超连续谱     

基于光子晶体光纤的百瓦量级超连续谱光源研究

采用脉冲重复频率可调的高功率皮秒脉冲光纤激 光抽运光子晶体光纤产生了平均输出功率为101 W的全 光纤化超连续谱. 通过一系列的对比实验, 详细研究了抽运激光的脉冲重复频率以及光子晶体光纤的长度对超连续谱产生的影响. 最后, 对如何实现更高平均功率的超连续谱输出进行相关的分析和讨论. 相关研究结果可以为进一步发展基于光子晶体光纤的高功率超连续谱光源提供一定的参考. 关键词： 光子晶体光纤 非线性光纤光学 超连续谱产生     

长脉冲抽运光子晶体光纤四波混频和超连续谱的理论研究

本文数值研究了长脉冲抽运光子晶体光纤四波混频和超连续谱的产生.依据准连续波近似下的相位匹配条件和能量守恒定律,能够理论上确定在光子晶体光纤正常色散区抽运时,四波混频效应产生的信号光和空闲光波长;以及在光纤反常色散区抽运时,调制不稳现象产生的两个对称旁瓣波长.利用自适应分步傅里叶法,定量地模拟了利用波长为1064 nm的亚纳秒激光器抽运两种不同色散特性的光子晶体光纤四波混频效应和超连续谱的产生,模拟结果与实验结果符合非常好. 关键词： 光子晶体光纤 超连续谱 四波混频 自适应分步傅里叶法     

光子晶体光纤反常色散区抽运产生超连续谱的相干特性分析

使用复互相干度的定义对超连续谱的相干性进行了数值计算,得到了不同功率抽运情况下的脉冲谱展宽以及超连续谱相干性的变化.结果表明孤子自频移以及色散波辐射是抽运波长位于光纤反常色散区情况下超连续谱展宽的主要物理机理,而超连续谱的相干性则主要受到调制不稳定性的影响.调制不稳定性放大抽运脉冲自身携带的随机噪声,使得非线性效应产生的光谱成分具有随机的相位与幅度,引起超连续谱相干性的下降. 抽运功率越高, 调制不稳定性增益越高,噪声对超连续谱产生的作用越强, 超连续谱的相干性越差.要获得高相干的超连续谱, 需采用峰值功率较小的脉冲进行抽运.要获得大谱宽高相干的超连续谱, 则需要合理选择抽运脉冲功率.     

飞秒脉冲抽运掺镱微结构光纤产生超连续谱的实验研究

本文利用钛蓝宝石飞秒激光器抽运自制的掺镱微结构光纤,对微结构光纤中的非线性效应及超连续谱产生机理进行了实验研究.研究发现,当抽运光偏离Yb~(3+)吸收最高峰85 nm时,仍具有较高的发光效率.在飞秒脉冲抽运下,位于反常色散区的发射光首先被位于正常色散区的抽运光激发、放大并俘获,然后演化为超短脉冲,随后在微结构光纤中产生非线性效应.微结构光纤1发射光位于零色散波长附近,产生基阶孤子并在拉曼作用下红移,微结构光纤2发射光位于距离零色散波长较远的反常色散区,产生高阶孤子分裂效应形成超连续谱,但是1380 nm处的OH-吸收限制了超连续谱的进一步展宽.忽略抽运光耦合效率、微结构光纤损耗等因素的影响,输出光谱中超连续谱的产生效率最高可以达到98%以上,意味着几乎所有的残余抽运光和发射光均展宽为超连续谱.在0.50 m长的微结构光纤中,获得了较高的波长转换效率和较宽的超连续谱.通过拉锥处理,零色散波长发生蓝移,最终产生的超连续谱相在短波处范围展宽,而在长波处范围缩短.因此利用钛蓝宝石飞秒激光器抽运Yb~(3+)掺杂微结构光纤,可以获得可调谐的超连续谱.     

在色散渐减光子晶体光纤中产生超连续谱的实验研究

本文利用非线性偏振锁模激光器产生的重复频率50 MHz, 脉宽为1.8 ps的脉冲分别抽运外径均匀和色散渐减两种高非线性光子晶体光纤, 在三阶非线性效应 (自相位调制、交叉相位调制、四波混频和受激拉曼散效应等) 和色散共同作用下得到扩展至蓝光部分的超连续谱. 模拟了光谱在色散渐减光纤和均匀光纤中的展宽过程, 通过对比均匀光纤发现色散渐减光纤在调控色散, 加强拉曼孤子和色散波的群速度匹配条件, 产生超带宽光谱方面具有很大优势. 实验利用20 m长的色散渐减光纤, 得到了406.1至671.8 nm的可见光波段增强的较为平坦的超连续谱. 关键词： 超连续谱 色散渐减光子晶体光纤 群速度匹配 非线性效应     

基于全正色散光子晶体光纤的超连续谱光源

利用预估校正分步傅里叶法数值求解非线性薛定谔方程, 模拟超短激光脉冲在全正色散光子晶体光纤中传输时的演化情况, 分析了不同脉宽和能量的脉冲对产生的超连续谱的影响. 结果表明: 无啁啾高斯脉冲在此全正色散光子晶体光纤中传输时, 始终保持单个脉冲特性, 提高脉冲峰值功率可进一步展宽获得的超连续谱.模拟结果同时表明, 利用中心波长为1060 nm, 脉宽和能量分别为50 fs, 15 nJ的脉冲抽运此光纤, 当传输12 cm 后便可获得具有较好的光谱连续性和光谱平坦度的超连续谱. 进一步模拟结果表明, 采用棱镜对对其进行脉冲压缩, 可获得脉宽约15 fs, 谱宽约700 nm的理想超连续谱光源. 关键词： 超连续谱 光子晶体光纤 全正色散     

数值模拟亚纳秒脉冲产生超连续谱的一种改进方法(英文)

提出了一种基于分步傅里叶方法的二次采样法,用以模拟和分析亚纳秒脉冲泵浦光子晶体光纤产生的超连续谱特性。通过此方法在广义非线性薛定谔方程上的应用,在超连续谱模拟中显著缩短了运算时间,模拟结果与实验符合很好。同时还对模拟光谱与实验结果间的细微差别做了讨论。通过此方法,模拟了1.8m晶体光纤中产生的1.15 W续谱和光谱沿光纤长度的演化,为超连续谱实验研究的优化设计提供了依据。     

Generation of an ultrabroadband supercontinuum in the mid-infrared region using dispersion-engineered GeAsSe photonic crystal fiber

An ultrabroadband mid-infrared (MIR) region supercontinuum (SC) is demonstrated numerically through dispersion-engineered traditional chalcogenide (ChG) photonic crystal fiber (PCF). By varying structural parameters pitch (hole to hole spacing) and air-hole diameter to pitch ratio, a number of 10-mm-long hexagonal PCFs made employing GeAsSe ChG glass as a core and air-holes of hexagonal lattice running through their lengths as a cladding are optimized to predict an efficient mid-infrared region SC spectral emission by pumping them using a tunable pump source between 2.9 and 3.3 µm. Simulations are carried out using an ultrashort pump pulse of 100-fs duration with a low pulse peak powers of between 3 and 4 kW into the optimized designs. It is found through numerical analysis that efficient SC spectral broadening with flattened output can be obtained by increasing the PCF pitch rather than increasing the PCF cladding containing air-hole diameter although a larger nonlinear coefficient could be obtained through increasing air-hole diameter of an optimized design. Simulation results show that the SC spectra can be broadened up to 12.2 µm for a certain design with a peak power of 3 kW. Using a peak power of 4 kW, it is possible to obtain SC spectral broadening beyond 14 µm with an optimized design spanning the wavelength range from 1.8 to 14 µm which covers the electromagnetic spectrum required for MIR molecular fingerprint region applications such as sensing and biological imaging.     

Generation of a compact high-power high-efficiency normal-dispersion pumping supercontinuum in silica photonic crystal fiber pumped with a 1064-nm picosecond pulse

Broadband normal dispersion pumping supercontinuum （SC） generation in silica photonic crystal fiber （PCF） is investigated in this paper. A 1064-nm picosecond fiber laser is used to pump silica PCF for the SC generation. The length of PCF is optimized for the most efficient stimulated Raman scattering process in the picosecond pump pulse region. The first stimulated Raman Stokes peak is located in the anomalous dispersion regime of the PCF and near the zero dispersion wavelength; thus the SC generation process can benefit from both a normal dispersion pumping scheme and an anomalous dispersion pumping scheme. The 51.7-W SC spanning from about 700 nm to beyond 1700 nm is generated with an all-fiber configuration, and the pump-to-SC conversion efficiency is up to 90%. In order to avoid the output fiber end face damage and increase the stability of the system, an improved output solution for the high power SC is proposed in our experiment. This high-efficiency near-infrared SC source is very suitable for applications in which average output power and spectral power density are firstly desirable.     

20 W all fiber supercontinuum generation from picosecond MOPA pumped photonic crystal fiber

An all fiber high power supercontinuum (SC) source is demonstrated by pumping a section of photonic crystal fiber (PCF) with a picosecond MOPA laser. The core of the PCF is enlarged at the input end through a serious of PCF post processing method to match the output fiber of the picosecond laser, to ensure low loss splicing, hence high power operation of the whole system. The supercontinuum output spectrum covers the wavelength range from 650 nm to beyond 1700 nm. Limited by available pump power, 20 W super-continuum output power is obtained under 29.5 W picosecond pump power, giving a high optical to optical conversion efficiency of 67.8%.     

All fiber supercontinuum light source using photonic crystal fibers pumped by nanosecond fiber laser pulses

A novel compact supercontinuum (SC) source using the single mode photonic crystal fibers (PCF) pumped with an all fiber MOPA fiber laser is demonstrated experimentally. A bandwidth of 700 nm is achieved by operating the pumping fiber laser at a wavelength of 1064 nm, pulse duration of 10 ns, repetition rate of 50 kHz and peak power of 1 kW. The SC generation is initiated through modulation instability (MI) which breakups the nanosecond pump pulses into picosecond or femtosecond pulses, and further broadened through nonlinear effects of PCF.     

Supercontinuum generated in all-normal dispersion photonic crystal fibers with picosecond pump pulses

The supercontinuum (SC) generation in all-normal dispersion (ANDi) photonic-crystal fiber (PCF) pumped by high power picosecond pulses are investigated in this paper. Our results show that an octave SC may be achieved by pumping the ANDi PCF with picosecond pump pulses. However, the PCF length required may have to be lengthened to several tens of centimeters, which is much longer than that with femtosecond pump pulses. The relatively long PCF gives rise to much higher Raman gain and stronger Raman frequency shift compared to those with femtosecond pump pulses, which in turn not only cause a distorted temporal waveform and an un-flattened spectrum, but also severely degrade the coherence of the generated SC.     

Build-up of supercontinuum in heated and unheated photonic crystal fibers using a chirped femtosecond laser

The build-up of supercontinuum in a photonic crystal fiber (PCF) has been investigated experimentally as a function of pump power using chirped 100-fs pulses from a Ti:sapphire laser. As compared with the PCF at room temperature, a new blue-shifted spectral component is observed in the initial steps of supercontinuum (SC) generation when the central part of PCF is heated to 120 °C by a hot plate. In addition, the slope efficiency of SG is slightly improved with the slightly extension of supercontinuum spectrum in blue edge at high pump powers. The change in dispersion property as well as the effective cascading of nonlinear photonic crystal fibers for heated PCF would be the main attributions.     

Infrared supercontinuum from a large mode area PCF under extreme picosecond excitation

Evolution of the long-wavelength edge of supercontinuum (SC) in a large mode-area photonic crystal fiber (LMA PCF) under extreme (close to the fiber damage threshold) picosecond excitation is analyzed for the first time to our knowledge. The obtained results are interpreted on the basis of the numerical simulations explaining both spectral and temporal characteristics of SC in dependence on the pulse power and the fiber length. An existence of the minimum LMA PCF length providing the broadest spectrum under the highest picosecond excitations is predicted. The multimode cross-modulation inside the LMA PCF is analyzed, as well.      

Broad spectral sliced multiwavelength source with a mode locked fiber laser

A simple multi-wavelength source is demonstrated based on spectral slicing of supercontinuum (SC) light using a Sagnac loop mirror. A mode locked fiber laser with pulse width of 800 fs is employed to generate the SC in photonic crystal fiber (PCF). The SC light extending from 1200 nm up to the wavelength region above 1750 nm is obtained at the amplified pulse pump power of 30 dBm. By slicing the SC with a loop mirror, a multiwavelength comb spectrum is obtained with different channel spacing for different operating wavelength region. Spacings of 1.5, 2.3, and 2.9 nm are shown at wavelength regions of 1220, 1450, and 1730 nm, respectively. It is also observed that the signal to noise ratio (SNR) increases from 15 to 20 dB as the operating wavelength increases from 1220 to 1730 nm region.     

利用锁模光纤激光器在色散位移光纤中产生超连续谱的研究

采用主动锁模光纤激光器输出的重复频率10GHz、脉宽7．97ps的脉冲作为抽运光源,无需压缩后直接抽运4．2km的普通色散位移光纤(DSF)．利用色散位移光纤中自相位调制、交叉相位调制等非线性效应的联合作用,获得了20dB带宽达125nm、覆盖整个C波段、L波段和部分S波段的超连续(SC)谱。实验研究了抽运光脉冲峰值功率和抽运波长对超连续谱宽度的影响,结果表明抽运光脉冲峰值功率越高,得到的超连续谱的带宽越宽;通过对抽运波长的优化,可以实现最大程度的超连续展宽;分析了滤波器带宽对脉冲质量的影响;利用0．4nm带宽的可调谐滤波器对从超连续谱中滤出脉冲的特性进行了研究,在超连续谱的不同波长处获得了脉宽为8．90～9．80ps、时间一带宽积为0．44～0．49的稳定的窄光脉冲。     

Active phase control and frequency chirp effects on supercontinuum generation in high birefringence photonic crystal fiber

An acoustic-optics programmable dispersive filter (AOPDF) was first employed to actively control the linearly polarized femtosecond pump pulse frequency chirp for supercontinuum (SC) generation in a high birefringence photonic crystal fiber (PCF). By accurately controlling the second order phase distortion and polarization direction of incident pulses, the output SC spectrum can be tuned to various spectral energy distributions and bandwidths. The pump pulse energy and bandwidth are preserved in our experiment. It is found that SC with broader bandwidth can be generated with positive chirped pump pulses except when the chirp value is larger than the optimal value, and the same optimal value exists for the pump pulses polarized along the two principal axes. With optimal positive chirp, more than 78% of the pump energy can be transferred to below 750 nm. Otherwise, negative chirp will weaken the blue-shift broadening and the SC bandwidth.