聚丙烯/氧化铝纳米电介质的陷阱与直流击穿特性

聚丙烯电介质的直流击穿场强是影响其储能密度的关键因素,纳米氧化铝掺杂是一种提高聚合物电介质击穿场强的有效方法,因此有必要开展聚丙烯/氧化铝纳米电介质直流击穿特性的研究.为了探究其直流击穿机理,通过熔融共混法制备了聚丙烯/氧化铝纳米电介质试样,观察了其显微结构,并对其表面电位衰减特性、体电阻率和直流击穿场强进行了测试.实验结果表明,随着纳米氧化铝含量的增加,深陷阱能级和密度、体电阻率和直流击穿场强都呈现先升高后降低的趋势,当纳米氧化铝含量为0.5 wt%时出现最大值,其中,直流击穿场强相比于未掺杂时可提高27%左右.根据纳米电介质交互区模型,分析了聚丙烯/氧化铝纳米电介质的显微结构和陷阱参数之间的关系.基于空间电荷击穿理论,利用陷阱参数对聚丙烯/氧化铝纳米电介质直流击穿机理进行了探讨.认为交互区为聚丙烯/氧化铝纳米电介质提供了更多深陷阱,而深陷阱能级和密度在较高纳米掺杂量时出现不同程度的降低可能是由双电层模型交互区重叠所致;深陷阱能级和密度的增加可降低载流子的注入量,进而提高其体电阻率和直流击穿场强.     

聚醚酰亚胺纳米复合电介质中指数分布陷阱电荷跳跃输运对储能性能的影响

目前常见聚合物电介质电容器的储能性能在高温下会急剧劣化,难以满足航空航天和能源等领域的需求.为提高介质高温储能性能,常掺杂纳米填料对电介质改性,通过改变电介质内部陷阱参数来调控电荷输运过程,但其内部陷阱的能级和密度与储能性能间的定量关系仍需进一步研究.本文构建线性聚合物纳米复合电介质中指数分布陷阱电荷跳跃输运的储能与释能模型并进行了仿真.纯聚醚酰亚胺在150℃的体积电阻率和电位移矢量-电场强度回线的仿真结果与实验符合,证明了模型的有效性.不同陷阱参数纳米复合电介质的仿真结果表明,增大总陷阱密度和最深陷阱能级,会降低载流子迁移率、电流密度和电导损耗,提升放电能量密度和充放电效率.在150℃和550 kV/mm外施场强下,1.0 eV最深陷阱能级和1×10²⁷ m^-3总陷阱密度的纳米复合电介质放电能量密度和充放电效率分别为4.26 J/cm³和98.93%,相比纯聚醚酰亚胺提升率分别为91.09%和227.58%,显著提升了高温储能性能.本研究为耐高温高储能性能电容器的研发提供了理论和模型支撑.     

以能带理论诠释直流聚乙烯绝缘中空间电荷的形成和抑制机理

高压直流塑料交联聚乙烯电缆的研发难点是消除其中的空间电荷效应. 目前, 国内外学者普遍通过添加纳米粒子在聚乙烯体内形成深陷阱捕获电荷的机理来抑制电荷积聚, 但此抑制机理违背了电场的基本理论. 以能带理论全面阐述聚合物介质中空间电荷的形成和抑制机理, 从一级陷阱模型出发, 应用电荷入陷和脱陷动力方程, 推导了聚合物介质中空间电荷的形成过程. 在聚合物介质中引入深陷阱后, 介质Fermi能级位移, 电极与介质之间界面接触由Ohm接触转变为阻塞接触. 考虑到无定形相中大量的陷阱密度, 电荷耗尽区宽度小于100 Å, 电极与介质之间的界面对电子变得透明, 形成中性接触, 在电压作用下, 这种聚乙烯介质中不再可能形成空间电荷. 最后, 在纯聚乙烯和纳米改性后含有深陷阱的聚乙烯两种试样上, 分别测量了电导与电场强度的关系和空间电荷分布曲线, 实验结果符合理论推导. 关键词： 直流绝缘 能带理论 空间电荷 抑制机理     

聚乙烯空间电荷包行为的形成机理与仿真方法研究

聚乙烯中的空间电荷包行为是空间电荷的一种特殊的输运行为.研究表明,空间电荷包行为由于受材料本身特性、外加电场大小以及环境温度等的影响,导致其产生过程及传输特性上存在较大差异,这些因素给空间电荷包行为产生机理研究带来了较大困难.通过对电荷的电极注入过程、载流子的体内迁移规律及空间电荷与体内陷阱的相互作用机制进行分析,探讨了不同外加电场及不同深度陷阱能级对电荷包行为造成的相关影响,在此基础上建立物理模型来描述电荷包的产生和迁移过程.模型中提出了在高于阈值电场时,载流子迁移速度与电场关系存在负微分迁移率的假设.基于此模型对空间包行为的模拟结果与实验结果取得较好的一致. 关键词： 空间电荷包 数值模拟 负微分迁移率     

聚合物材料空间电荷陷阱模型及参数

采用电声脉冲测量技术研究了直流电场下低密度聚乙烯材料的电荷入陷和脱陷特征. 发现在不同电场周期下样品的电荷衰减呈现不同的特征, 为此提出了一个简单的基于两陷阱水平的入陷和脱陷模型, 并计算了相应的参数, 如陷阱能级和密度. 确定了不含任何添加剂的低密度聚乙烯样品中存在的两种水平的陷阱能级分别为: 较浅陷阱能级0.77–0.81 eV 对应的浅陷阱电荷密度为(1.168–1.553)× 10¹⁹ m^-3; 较深陷阱能级0.96–1.01 eV 对应的深陷阱电荷密度为(1.194–4.615)× 10¹⁸ m^-3. 最后初步验证了材料的深陷阱能级和对应的深陷阱电荷密度随老化而增加, 可考虑将模型中的两能级陷阱参数作为老化诊断特征参量. 关键词： 聚合物 空间电荷 陷阱 老化     

孔洞聚丙烯驻极体膜中空间电荷与孔洞击穿电荷的俘获特性

对孔洞聚丙烯(PP)驻极体膜系统的研究结果表明：孔洞PP膜中空间电荷的俘获特性随注入的空间电荷量或试样表面电位而变化,注入的电荷量较少时空间电荷主要被俘获在表面深陷阱和近表面次深陷阱中,较多的注入电荷量时空间电荷在进一步填充表层(表面和近表面)陷阱的同时,还将填充体内浅陷阱;这三类陷阱中心所对应的电荷脱阱温度分别约为160℃,138℃和92℃.而孔洞击穿电荷不仅被俘获在与试样表层空间电荷陷阱相似的孔洞表层陷阱中,还有相当的量穿过孔洞表层进入体内、成为浅阱俘获孔洞击穿电荷. 关键词： 孔洞聚丙烯膜 空间电荷 孔洞击穿电荷 俘获特性     

注入和输运对单层有机发光器件复合发光的影响

通过分析聚合物电致发光器件中载流子注入、输运、激子的解离与复合过程,提出了激子解离与复合的理论模型. 基于电流连续性方程和Poisson方程,给出了激子复合密度、电流密度及复合效率表达式.研究两电极与有机层之间在Ohmic和Fowler-Nordheim接触条件下载流子迁移率对器件中激子的复合密度及外加电压和注入势垒对器件电流和复合效率的影响.结果表明:1)在一个较宽的注入势垒和迁移率范围内,复合密度不是由两个注入电极的相对注入比决定而是由有机层电子和空穴迁移率之比所支配;2)固定阴极势垒,而阳极势垒由小变大时,器件电流由接触限制向空间电荷限制转变;3)复合效率随外电压升高先增加,当电压达一临界值时而陡降,存在一个最佳的注入势垒值.结果说明:电极与有机层的能带匹配及有机层间的迁移率匹配对器件复合发光有着极其重要的影响.其计算值与所报道的理论结果相符.     

线性低密度聚乙烯中空间电荷陷阱的能量分布与空间分布的关系

使用激光感应压力波法和热刺激放电技术,系统地研究了直流高压作用下线性低密度聚乙烯(LLDPE)半导性电极试样中空间电荷的形成和演变及电荷陷阱分布和退极化过程.在直流高压作用下试样中空间电荷的分布明显地表现为两电极同极性电荷快速对称注入的特征,半导性电极与LLDPE的界面近乎呈现欧姆接触特征.LLDPE中的电荷陷阱分布表现出体内为浅陷阱、表层为深陷阱的特征.半导性电极与LLDPE薄片间的压合条件或电极材料对LLDPE表层的掺杂显著地影响表层陷阱的能量分布,导致表层中较深陷阱的深度和密度减小、较浅陷阱的密度增大.在整个短路退极化过程中,试样中正、负电荷的中心分别向距它们较近的电极迁移,而在开路退极后期则表现为与短路时不同的行为、被表层深陷阱再俘获的电荷脱阱后向背电极迁移. 关键词： 线性低密度聚乙烯 空间电荷 陷阱分布 热刺激放电     

有机固体中载流子陷阱的表征

有机固体包括有机分子晶体、非晶态有机固体、有机高聚物等.在有机固体中保持单个分子的特性,如吸收光谱;分子间的范德瓦耳斯相互作用能比较小,即使是单晶体,也容易产生结构欠序和杂质、晶界等缺陷.这些缺陷使电子价带与导带间的禁区中出现局域能级,导带的载流子(电子)或价带的载流子(空穴)会被局域于这些杂质或缺陷的附近,出现电荷存储现象,影响稳态和瞬态电导下的载流子输运,导致暗导的非欧姆性、载流子迁移率的下降、光导衰减时间大于光激发载流子的寿命等.多年来,这些一直被固体的电导和光导研究者所重视[1-6],并称这些局域能级为陷阱.…     

宽范围偏置电流下的GaAlAs红外发光二极管1/f噪声特性

在宽范围偏置条件下,测量了GaAlAs红外发光二极管(IRLED)的低频噪声,发现1/f噪声幅值与偏置电流的γ次方成正比,在小电流区,γ≈1,在大电流区γ≈2.基于载流子数涨落和迁移率涨落机制建立了一个GaAlAs IRLED 1/f噪声模型,该模型的分析表明,低电流区GaAlAs IRLED的1/f噪声源于体陷阱对载流子俘获和发射导致的扩散电流涨落,高电流区的1/f噪声源于结空间电荷区附近氧化层陷阱对该处表面势的调制而引起载流子表面复合速率的涨落.该研究结果为1/f噪声表征GaAlAs IRLED的可靠性提供了实验基础与理论依据.     

The effect of Te alloying on the electronic gap of a-Se

The effect on the electronic density of gap states in a-Se produced by the isoelectronic additive Te has been studied by a combination of drift mobility and xerographic measurements. Drift mobility experiments probe the shallow gap states which control photoinjected carrier transport. Addition of Te to Se in the nominal range 0–18 wt.% progressively decreases both electron and hole drift mobility while simultaneously increasing dispersion. The number and distribution of deep gap states which control injected carrier range have been determined in the same films from analysis of xerographic residual potentials. Taken together these measurements show that progressive addition of Te to a-Se increases the integrated number of deep traps and broadens the distribution of both deep and shallow transport interactive electronic gap states.     

Temperature dependence of two-beam coupling and dark decay in photorefractive BaTiO3

The temperature dependence of two-beam coupling and dark decay in photorefractive BaTiO₃ is reported. We show that the competition between deep and shallow traps depends on temperature and writing intensity, and influences two-beam coupling and dark decay. The dynamics of dark decay, characterized by a fast decay of partial erasure and a subsequent slow decay, is influenced by the presence of deep and shallow traps. Partial erasure, due to thermal excitation of charges from the shallow traps, decreases with temperature and increases with writing intensity. The time constant of the slow decay, due to thermal excitation of charges from the deep traps, depends strongly on temperature, but not on the writing intensity. At room temperature, the existence of deep and shallow trap leads to intensity-dependent photorefractive gains. As temperature increases, the influence from the shallow trap decreases, and the photorefractive gain becomes independent of the intensity. However, at much higher temperatures (100°C), the photorefractive gain resumes its dependence on intensity due to an increase in dark conductivity at elevated temperature.     

Experiment and simulation of space charge suppression in LDPE/MgO nanocomposite under external DC electric field

In this paper, space charge dynamics under DC electric field of −100 kV/mm in low-density polyethylene (LDPE) and its nanocomposite containing a small amount of MgO nanoparticles were measured using an improved pulsed electro-acoustic (PEA) system. Unlike negative packet-like space charge accumulating in LDPE films, no remarkable space charge was observed in LDPE/MgO nanocomposite films, which indicated that the introduction of MgO nanoparticles played a key role on the space charge suppression. Different with current qualitative models, this paper describes space charge suppression on the basis of simulation using the bipolar charge transport model, which featured bipolar charges injection, transport, trapping, recombination, and extraction process. It was shown from the simulation that trap depth, trap concentration, local electric field and charge injection barrier height were all significant factors on the space charge suppression process. A deeper trap depth in LDPE/MgO nanocomposites made it easier for traps to capture mobile carriers. And a larger trap concentration effectively slowed down the whole carrier movement although there seemed a trap concentration threshold less than 30 Cm⁻³, above which this effect became slight. In addition, both the high permittivity of LDPE/MgO nanocomposites and low local electric field in the vicinity of cathode led to a larger injection barrier height based on the Schottky injection law, which would tremendously block the charge injection. At last, the suppression mechanism of space charge formation in the LDPE/MgO nanocomposites is presented.     

Effects of contact resistance on the evaluation of charge carrier mobilities and transport parameters in amorphous zinc tin oxide thin-film transistors

Accurate determination of the charge transport characteristics of amorphous metal-oxide transistors requires the mitigation of the effects of contact resistance. The use of additional electrodes as voltage probes can overcome contact resistance-related limitations and yields accurate charge carrier mobility values, trap depths and temperature and carrier density dependencies of mobility as well as trap depths. We show that large differences in measured charge carrier mobility values are obtained when such contact resistances are not factored out. Upon exclusion of the contact resistance, the true temperature dependence of charge carrier mobility appears in the form of two clearly distinct mobility regimes. Analyzing these revealed mobility regions leads to a more accurate determination of the underlying transport physics, which shows that contact resistance-related artefacts yield incorrect trends of trap depth with gate voltage, potentially leading to a misconstruction of the charge transport picture. Furthermore, a comparison of low- and high-mobility samples indicates that the observed effects are more general.     

Transport studies on filler-doped chitosan based polymer electrolyte

The room temperature conductivity of the chitosan complex containing 40 wt.% of salt increased from 6.02×10⁻⁶ Scm⁻¹ to 2.10×10⁻⁵ Scm⁻¹ after the addition of 1.0 wt.% aluminosilicate. Conductivity of the electrolyte is contributed from the charge carrier density and ionic mobility. The Rice and Roth model was applied in calculating the mobility, μ and density of ions, n. The number density of ions, n, increases with temperature, while mobility, μ decreases with increasing temperature. This work also suggests that the filler did not change the conduction mechanism of the charge carrier in chitosan-salt-filler complexes but helped to increase the conductivity value of the materials. Paper presented at the International Conference on Functional Materials and Devices 2005, Kuala Lumpur, Malaysia, June 6 – 8, 2005.     

单层有机器件的电子传输特性的数值模拟

在漂移扩散模型的基础上建立了单层有机器件的模型,包括了电荷注入、传输、空间电荷效应和陷阱的影响.电荷注入考虑了热电子发射电流和隧道电流.模拟得到的结果和文献中报道的实验测试数据一致.模拟研究了各个因素对器件J-V曲线的影响,电流和器件长度成反比,电流随着空穴注入势垒的减小而增加.电子注入势垒从1.7 eV减少到0.5 eV时,电流随着电子注入势垒的减小而减小,这主要是因为有机材料中电子迁移率太小,电子注入电流的增加可以忽略,而电子注入势垒的减小使内建势增加,在同样的电压下,场强 关键词： 有机器件 传输特性 数值模拟     

Temperature-dependent transport in suspended graphene

The resistivity of ultraclean suspended graphene is strongly temperature (T) dependent for 50.5 x 10(11) cm(-2), the resistivity increases with increasing T and is linear above 50 K, suggesting carrier scattering from acoustic phonons. At T=240 K the mobility is approximately 120,000 cm2/V s, higher than in any known semiconductor. At the charge neutral point we observe a nonuniversal conductivity that decreases with decreasing T, consistent with a density inhomogeneity <10(8) cm(-2).     

Current-voltage characteristics of poly(diphenylenephthalide) thin films

Charge transfer near the threshold of polymer film transition (induced by a low uniaxial pressure) to the high-conductivity state is studied in an attempt to tackle the question of how the energy band structure of a wide-gap organic insulator varies near this threshold. The I-V characteristics of poly(diphenylenephthalide) films of various thickness versus uniaxial pressure are analyzed. The results obtained are treated within the model of space-charge-limited injection currents. The parameters of the injection model, such as the equilibrium concentration of electrons, electron mobility, the occupation of traps, etc., are estimated. It is concluded that deep traps due to an excess charge may appear in the energy gap of the polymer near the imref. This probably causes a narrow subband to arise, and charge transfer via this subband increases the charge carrier mobility and, hence, conductivity.