Microstructural, optical and photocatalytic properties of CdS doped TiO2 thin films

CdS doped TiO₂ thin films (with CdS content=0, 3, 6, 9 and 12 at%) were grown on glass substrates. The X-ray diffraction analysis revealed that the films are polycrystalline of monoclinic TiO₂ structure. The microstructure parameters of the films such as crystallite size (D_ν) and microstrain (e) are calculated. Both the crystallites size and the microstrain are decreased with increasing CdS content. The optical constants have been determined in terms of Murmann's exact equations. The refractive index and extinction coefficient are increased with increasing CdS content. The optical band gap is calculated in the strong absorption region. The possible optical transition in these films is found to be an allowed direct transition. The values of E_g^opt are found to decrease as the CdS content increased. The films with 3 at% CdS content have better decomposition efficiency than undoped TiO₂. The films with 6 at% and 9 at% CdS content have decomposition efficiency comparable to that of undoped TiO₂, although they have lower band gap. The CdS doped TiO₂ could have a better impact on the decomposing of organic wastes.     

Study of Al2O3/TiO2 reflectivity enhancing bi-layer films on bright aluminium substrates

Al₂O₃/TiO₂ bi-layer films on aluminium substrates have been obtained by combining anodising and TiO₂ sol-gel deposition. The reflectivity enhancing properties of these Al₂O₃/TiO₂ bi-layer films have been studied in relation to the refractive index and thickness of the Al₂O₃ and TiO₂ single-layers. It is shown that a significant improvement of reflectivity can be achieved by a proper optimisation of the bi-layer elaboration parameters.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Annealing effects on the optical and structural properties of Al2O3/SiO2 films as UV antireflection coatings on 4H-SiC substrates

Al₂O₃/SiO₂ films have been prepared by electron-beam evaporation as ultraviolet (UV) antireflection coatings on 4H-SiC substrates and annealed at different temperatures. The films were characterized by reflection spectra, ellipsometer system, atomic force microscopy (AFM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), respectively. As the annealing temperature increased, the minimum reflectance of the films moved to the shorter wavelength for the variation of refractive indices and the reduction of film thicknesses. The surface grains appeared to get larger in size and the root mean square (RMS) roughness of the annealed films increased with the annealing temperature but was less than that of the as-deposited. The Al₂O₃/SiO₂ films maintained amorphous in microstructure with the increase of the temperature. Meanwhile, the transition and diffusion in film component were found in XPS measurement. These results provided the important references for Al₂O₃/SiO₂ films annealed at reasonable temperatures and prepared as fine antireflection coatings on 4H-SiC-based UV optoelectronic devices.     

Correlation between microstructure and optical properties of nano-crystalline TiO2 thin films prepared by sol-gel dip coating

Titanium dioxide thin films have been prepared from tetrabutyl-orthotitanate solution and methanol as a solvent by sol-gel dip coating technique. TiO₂ thin films prepared using a sol-gel process have been analyzed for different annealing temperatures. Structural properties in terms of crystal structure were investigated by Raman spectroscopy. The surface morphology and composition of the films were investigated by atomic force microscopy (AFM). The optical transmittance and reflectance spectra of TiO₂ thin films deposited on silicon substrate were also determined. Spectroscopic ellipsometry study was used to determine the annealing temperature effect on the optical properties and the optical gap of the TiO₂ thin films. The results show that the TiO₂ thin films crystallize in anatase phase between 400 and 800 °C, and into the anatase-rutile phase at 1000 °C, and further into the rutile phase at 1200 °C. We have found that the films consist of titanium dioxide nano-crystals. The AFM surface morphology results indicate that the particle size increases from 5 to 41 nm by increasing the annealing temperature. The TiO₂ thin films have high transparency in the visible range. For annealing temperatures between 1000 and 1400 °C, the transmittance of the films was reduced significantly in the wavelength range of 300-800 nm due to the change of crystallite phase and composition in the films. We have demonstrated as well the decrease of the optical band gap with the increase of the annealing temperature.     

TiO2/polyaniline nanocomposite films prepared by magnetron sputtering combined with plasma polymerization process

Radiofrequency plasma polymerization in combination with direct current reactive magnetron sputtering is utilized for the synthesis of TiO₂/plasma polymerized aniline nanocomposite thin films. In the composite film, X-ray diffraction measurements reveal formation of nanocrystalline rutile TiO₂ of crystallite size 3.6 nm. Due to continuous bombardment of plasma species during simultaneous magnetron sputtering and plasma polymerization, the precursors of polymerization are broken and few functional groups are retained in the composite film. The plasma polymerized aniline has the direct optical band gap of 3.55 eV and the nanocrystalline rutile TiO₂ is wide gap semiconductor with indirect gap of 3.20 eV which suggests the existence of an energy barrier at the interface in the composite form. The ac conductivity of composite film shows significant improvement as compared to plasma polymerized aniline film and sputtered rutile TiO₂ film. The composite film may find potential application as antistatic coatings.     

Optical characteristics of amorphous V2O5 thin films colored by an excimer laser

The V₂O₅ films were prepared by an RF sputtering method, and the amorphous films were colored by an UV excimer laser. The crystallinity of the as-grown V₂O₅ film was degenerated greatly by laser irradiation, as determined by X-ray diffraction (XRD) and Raman studies. The transmission and complex refractive index spectra of the V₂O₅ film were affected by variations in the microstructure, including the surface morphology, crystalline structure, and substoichiometry with an oxygen deficiency. Considerable emissions due to oxygen vacancies and band transition of photoluminescence (PL) peaks were observed, and the peaks were significantly changed after laser irradiation. The variations in the optical properties in both films may be attributed to oxygen deficiency induced by laser irradiation.     

Structural properties of Al2O3 dielectrics grown on TiN metal substrates by atomic layer deposition

We investigated on the structural properties of Al₂O₃ dielectrics grown on TiN metal substrates using an atomic layer deposition technique with tri-methyl-aluminum and either O₃ or H₂O as the precursor and oxidant, respectively. The structural and morphological features of these films were examined by atomic force microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy measurements. We find that Al₂O₃ dielectric films with the O₃ oxidant exhibit a rough morphology, a thick TiO₂ film, and a small amount of contaminants such as carbon and hydrogen. The reason for the rapid diffusion of oxygen atoms into the TiN lattice leads to the formation of TiO₂ layer on the TiN substrate. This is due to the higher oxidation potential of the O₃ compared to the H₂O.     

Effects of depositing temperatures on structure and optical properties of TiO2 film deposited by ion beam assisted electron beam evaporation

TiO₂, which is high in refractive index and dielectric constant, plays an important role in the fields of optics and electronics. In this work, TiO₂ films were prepared on glass substrates by the technique of ion beam assisted electron beam evaporation. The films were deposited at 50, 150 and 300 °C, respectively. Then the as-deposited TiO₂ films were annealed at 450 °C for 1 h in vacuum atmosphere. Structures and optical properties of TiO₂ films were characterized by XRD, SEM, ellipsometry and spectrophotometer. As a result, the structure and the refractive index of films were improved by both the annealing and the increasing of the deposition temperature. The UV-vis transmittance spectra also confirmed that the deposition temperature has a significant effect on the transparency of the thin films. The highest transparency over the visible wavelength region of spectra was obtained at the deposition temperature of 300 °C. The allowed direct band gap at the deposition temperature ranging from 50 to 300 °C was estimated to be in the range from 3.81 to 3.92 eV.     

Structural, morphological and optical properties of CuAlS2 films deposited by spray pyrolysis method

The structural, morphological and optical properties of CuAlS₂ films deposited by spray pyrolysis method have been investigated. CuAlS₂ in the form of films is prepared at different deposition conditions by a simple and economical spray pyrolysis method. The structural, surface morphology and optical properties of the films were analyzed by X-ray diffraction (XRD), scanning electron microscope (SEM), atomic force microscope (AFM) and absorbance spectra, respectively. The films were polycrystalline, crystallized in a tetragonal structure, and are preferentially orientated along the (1 1 2) direction. Grain size values, dislocation density, and d% error of CuAlS₂ films were calculated. The optical band gap of the CuAlS₂ film was found to be 3.45 eV. The optical constants such as refractive index, extinction coefficient and dielectric constants of the CuAlS₂ film were determined. The refractive index dispersion curve of the film obeys the single oscillator model. Optical dispersion parameters E_o and E_d developed by Wemple-DiDomenico were calculated and found to be 3.562 and 12.590 eV.     

Preparation and photo-induced superhydrophilicity of composite TiO2-SiO2-In2O3 thin film

In this work, TiO₂-SiO₂-In₂O₃ composite thin films on glass substrates were prepared by the sol-gel dip coating process. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF) and X-ray photoelectron spectroscopy (XPS) were used to evaluate the structural and chemical properties of the films. UV-vis spectrophotometer was used to measure the transmittance spectra of thin films. The water contact angle (WCA) of thin films during UV/vis irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that fabrication of composite film has a significant effect on transmittance and superhydrophilicity of TiO₂ films.     

S180 cell growth on low ion energy plasma treated TiO2 thin films

X-ray photoelectron spectroscopy (XPS) was used to characterise the effects of low energy (<2 eV) argon ion plasma surface modification of TiO₂ thin films deposited by radio frequency (RF) magnetron sputter system. The low energy argon ion plasma surface modification of TiO₂ in a two-stage hybrid system had increased the proportion of surface states of TiO₂ as Ti³⁺. The proportion of carbon atoms as alcohol/ether (COX) was decreased with increase the RF power and carbon atoms as carbonyl (CO) functionality had increased for low RF power treatment. The proportion of C(O)OX functionality at the surface was decreased at low power and further increase in power has showed an increase in its relive proportion at the surface. The growth of S180 cells was observed and it seems that cells are uniformly spreads on tissue culture polystyrene surface and untreated TiO₂ surfaces whereas small-localised cell free area can be seen on plasma treated TiO₂ surfaces which may be due to decrease in C(O)OX, increase in CO and active sites at the surface. A relatively large variation in the surface functionalities with no change in the surface roughness was achieved by different RF plasma treatments of TiO₂ surface whereas no significant change in S180 cell growth with different plasma treatments. This may be because cell growth on TiO₂ was mainly influenced by nano-surface characteristics of oxide films rather than surface chemistry.     

Effects of deposition rates on laser damage threshold of TiO2/SiO2 high reflectors

TiO₂ single layers and TiO₂/SiO₂ high reflectors (HR) are prepared by electron beam evaporation at different TiO₂ deposition rates. It is found that the changes of properties of TiO₂ films with the increase of rate, such as the increase of refractive index and extinction coefficient and the decrease of physical thickness, lead to the spectrum shift and reflectivity bandwidth broadening of HR together with the increase of absorption and decrease of laser-induced damage threshold. The damages are found of different morphologies: a shallow pit to a seriously delaminated and deep crater, and the different amorphous-to-anatase-to-rutile phase transition processes detected by Raman study. The frequency shift of Raman vibration mode correlates with the strain in film. Energy dispersive X-ray analysis reveals that impurities and non-stoichiometric defects are two absorption initiations resulting to the laser-induced transformation.     

Spray pyrolytic deposition of transparent aluminum oxide (Al2O3) films

Optically transparent Al₂O₃ films has been synthesized, on quartz substrates at 500, 600 and 700 °C, from 0.02 M aluminum acetyl acetonate (Al(acac)₃) in ethanol, by using ultrasonic spray pyrolysis technique. The films synthesized at 500, 600 and 700 °C are amorphous having average particle sizes 27 ± 6, 18 ± 3 and 14 ± 3, respectively. The films are found to be 95% optically transparent in the visible region. The optical transparency of the films in the ultraviolet region is found to increase with increase in deposition temperature. The observed increase in optical band gap and decrease in refractive index is attributed to the decrease in particle size with increase in deposition temperature. The stoichiometry and chemical bonding of the amorphous film studied using XPS and FTIR spectroscopy revealed the presence chemisorbed oxygen.     

“In situ” XPS study of band structures at Cu2O/TiO2 heterojunctions interface

In an attempt to investigate influence of the defects on electronic structure of Cu₂O/TiO₂ heterojunctions, thin Cu₂O layers were successively deposited on TiO₂ that has different levels of defect concentrations, and the resultant band bending and offset characteristics were studied by in situ X-ray photoelectron spectroscopy (XPS). The TiO₂ substrates with defects were prepared by Ar⁺ sputtering, followed by annealing at different temperatures in oxygen atmosphere. Presence of the defects in TiO₂ surface dramatically influences on the band bending and band offset at the interface: more defects are on TiO₂ surface, less band bending are at the interface, inducing smaller conduction band offsets. On the reduced TiO₂ surface, Cu₂O was disproportionately decomposed to form CuO and Cu.     

Surface state of TiO2 treated with low ion energy plasma

The effect of low pressure radio frequency (rf) plasma treatment on TiO₂ surface states has been studied using X-ray photoelectron spectroscopy. Three different oxidation states of oxygen in untreated TiO₂ powder were observed, which suggests the existence of adsorbed water and carbon on the surface. The ratio of oxygen to titanium (O/Ti) was decreased for the low ion dose plasma treated samples due to desorption of water from the surface. In the case of Ti 2p about 20% of surface states were converted to Ti³⁺ 2p_3/2 state after plasma treatment with a very good stability, whereas untreated TiO₂ remained mostly as Ti⁴⁺ state. A rapid decrease in the ratio of carbon to titanium (C/Ti) at TiO₂ surface was also observed after plasma treatment and more than 90% of carbon atoms were removed from the surface. Therefore, the plasma treatment of TiO₂ has advantages to surface carbon cleaning, increasing O⁻ and Ti³⁺ surface states, hence improving the activity of TiO₂ for different environmental, energy and biological applications.     

Characteristics of N-doped TiO2 thin films grown on unheated glass substrate by inductively coupled plasma assisted dc reactive magnetron sputtering

N-doped TiO₂ thin films have been deposited on unheated glass substrates by an inductively coupled plasma (ICP) assisted direct current (dc) reactive magnetron sputtering. All films were produced in the metallic mode of sputtering in order to achieve a high deposition rate. The structures and properties of the N-doped TiO₂ films were studied by X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, field emission scanning electron microscopy and UV–Vis spectrophotometer. Experimental results show that we can obtain well crystallized N-doped anatase phase TiO₂ thin films at low deposition temperature and at high deposition rate by using the ICP assisted dc reactive magnetron sputtering process. The doping of nitrogen into TiO₂ lattices leads to a smooth shift of the absorption band toward visible light regions.     

Deposition and characterization of binary Al2O3/SiO2 coating layers on the surfaces of rutile TiO2 and the pigmentary properties

Binary Al₂O₃/SiO₂-coated rutile TiO₂ composites were prepared by a liquid-phase deposition method starting from Na₂SiO₃·9H₂O and NaAlO₂. The chemical structure and morphology of binary Al₂O₃/SiO₂ coating layers were investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, TG-DSC, Zeta potential, powder X-ray diffraction, and transmission electron microscopy techniques. Binary Al₂O₃/SiO₂ coating layers both in amorphous phase were formed at TiO₂ surfaces. The silica coating layers were anchored at TiO₂ surfaces via Si-O-Ti bonds and the alumina coating layers were probably anchored at the SiO₂-coated TiO₂ surfaces via Al-O-Si bonds. The formation of continuous and dense binary Al₂O₃/SiO₂ coating layers depended on the pH value of reaction solution and the alumina loading. The binary Al₂O₃/SiO₂-coated TiO₂ composites had a high dispersibility in water. The whiteness and brightness of the binary Al₂O₃/SiO₂-coated TiO₂ composites were higher than those of the naked rutile TiO₂ and the SiO₂-coated TiO₂ samples. The relative light scattering index was found to depend on the composition of coating layers.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

Investigation on properties of TiO2 thin films deposited at different oxygen pressures

TiO₂ thin films were prepared by electron beam evaporation at different oxygen partial pressures. The influences of oxygen partial pressure on optical, mechanical and structural properties of TiO₂ thin films were studied. The results showed that with the increase of oxygen partial pressure, the optical transmittance gradually increased, the transmittance edge gradually shifted to short wavelength, and the corresponding refractive index decreased. The residual stresses of all samples were tensile, and the value increased as oxygen partial pressure increasing, which corresponded to the evolutions of the packing densities. The structures of TiO₂ thin films all were amorphous because deposition particles did not possess enough energy to crystallize.