掺铬的镁橄榄石晶体连续波可调谐激光器

本文报道了连续波Nd:YAG激光器泵浦掺铬镁橄榄石(Cr⁴⁺:forsterite)晶体获得了连续波可调谐运转,该激光器采用Nd:YAG激光器的1.06μm谱线泵浦Φ5×9mm的Cr⁴⁺:forsterite晶体.在吸收泵浦功率为8.7W时,得到1.05W的连续波输出.当在腔内放置色散元件后,其调谐范围是1186nm～1306nm,同时详细研究了输出功率随温度和输出镜透过率的变化特性.     

LD端面泵浦Cr4:YAG被动调Q激光器输出特性研究

对激光二极管端面泵浦Cr⁴⁺:YAG被动调QNd:YAG激光器输出特性进行了实验研究.实验研究发现,激光器输出功率及脉冲重复频率随谐振腔长度增大而增大.为解释这一实验现象,测量了泵浦光斑在激光晶体内尺寸,同时计算了激光晶体及Cr⁴⁺:YAG晶体内的基模激光光斑半径随谐振腔长度变化.分析结果表明:激光晶体内泵浦光斑尺寸远小于激光晶体内基模光斑半径,腔模间交叠效率较低;当腔长增加时,激光晶体内的基模激光光斑减小,腔模间交叠效率增加,从而导致输出功率及脉冲重复频率随腔长增加而增加;另外,Cr⁴⁺:YAG晶体内光斑半径也随谐振腔长度减小,引起Cr⁴⁺:YAG晶体漂白时间缩短,导致脉冲重复频率随腔长增加而增加.     

腔内光强空间分布对被动调Q激光器速率方程解的影响

在被动调Q激光器速率方程中考虑腔内光强的高斯分布,数值求解该速率方程所得的理论结果比采用平面波近似所得的理论结果更接近于Cr⁴⁺:YAG调QNd³⁺:YAG激光器的实验结果.     

Er3+-Yb3+共掺杂光纤环型腔被动谐波锁模激光器

 报道了Er³⁺-Yb³⁺共掺杂光纤作为增益介质的环型腔光纤激光器。利用光纤的非线性偏振旋转效应产生可饱和吸收体的锁模机制,通过调整泵浦功率,调节偏振控制器的状态,实现了连续基波锁模和高阶谐波锁模两种稳定的锁模运转状态。其中连续基波锁模重复频率15.89 MHz,中心波长为1.557 nm,光谱宽度为9.9 nm。二阶谐波锁模重复率为31.79 MHz,三阶谐波锁模脉冲重复率为46.99 MHz。观察到了调Q锁模和调Q脉冲序列,给出了各种运转状态的实验结果并对多种锁模机理作了简要的分析。     

用时域ABCD矩阵对调Q锁模激光器的研究

用时域ABCD矩阵讨论了调Q锁模脉冲激光器输出脉冲的宽度和啁啾特性,主要给出了调Q元件作为幅度调制元件时的时域ABCD矩阵,并将光脉冲在激光腔中往返一周的ABCD矩阵写出,用此矩阵讨论了它对锁模脉冲的影响.给出了Nd:YAG激光器中用Cr⁴⁺:YAG作调Q元件时的调Q锁模脉冲激光器特性,并讨论了腔内色散、饱和吸收强度、增益带宽对输出脉冲特性的影响.用时域ABCD矩阵大大简化了计算过程.     

被动谐波锁模Er3+/Yb3+共掺双包层光纤环形腔激光器

 为了实现高重复频率和高功率的光脉冲,实验采用Er³⁺/Yb³⁺共掺双包层光纤作为增益介质,稳定的中心波长为976 nm的高功率半导体激光器作为泵浦源,利用非线性偏振旋转锁模技术,得到稳定的自起振锁模光脉冲。当泵浦功率为2.4 W时,激光器输出重复频率为8.829 MHz的连续锁模光脉冲,平均输出功率为52.5 mW,自起振锁模泵浦阈值功率为0.6 W,并观测到了稳定的高阶谐波锁模、调Q和调Q-锁模光脉冲输出。     

Gires-Tournois干涉镜补偿色散的自启动飞秒Cr4+:YAG激光器实验研究

利用一片GTI镜补偿腔内色散,并使用宽带半导体可饱和吸收片,实现了锁模自启动的飞秒Cr⁴⁺:YAG激光输出.在9W平均功率的1030nm激光抽运下,获得输出脉冲功率为95 mW,光谱半高全宽45 nm,中心波长1508 nm,实测脉冲宽度为65 fs.     

LD预泵浦条件与Cr4+,Nd3+:YAG微片激光器的输出特性

 建立了LD预泵浦的被动调Q平平腔Cr⁴⁺,Nd³⁺:YAG微片激光器模型,分析了预泵浦参数与激光脉冲时间特性的关系,设计了LD预泵浦的Cr⁴⁺,Nd³⁺:YAG微片激光器实验,测量了不同预泵浦参数下激光单脉冲以及脉冲序列的时间特性。实验结果与数值计算结果基本符合：调节预泵浦参数使每个泵浦脉冲刚好对应输出单个激光脉冲时,固定脉冲泵浦宽度,脉冲泵浦速率随连续泵浦速率的增加呈一次函数减小;固定连续泵浦速率,脉冲泵浦速率随脉冲泵浦宽度的增加呈非线性函数减小。结果还表明,激光脉冲半高全宽随整体泵浦速率的增加而减小,峰值功率随整体泵浦速率的增加而增加;当整体泵浦速率在阈值附近变动时,激光单脉冲时间特性的变化最为明显。     

Cs2 NaMF6(M=Al,Ga):Cr3+络合分子体系局域结构和基态分裂的理论研究

采用双自旋轨道耦合系数模型并结合完全能量矩阵的方法对Cs₂NaMF₆(M=Al, Ga):Cr³⁺ 体系中Cr³⁺ 离子的基态分裂和局域结构进行了研究.通过模拟光谱和EPR谱确定了Cr³⁺ 取代 M³⁺ 形成的两种占位结构的畸变角,发现用双自旋轨道耦合系数模型与单自旋轨道耦合系数模型计算出的畸变角Δθ存在较大的差异.这表     

Tm3+/Yb3+共掺碲酸盐玻璃的近红外发光及能量传递机理

采用高温熔融法制备了组分为TeO₂-ZnO-Na₂O的Tm³⁺离子单掺和Tm³⁺/Yb³⁺共掺碲酸盐玻璃,应用Judd-Ofelt理论计算分析了玻璃样品的强度参量Ω_t(t=2, 4, 6),自发辐射跃迁几率A,荧光分支比β和荧光辐射寿命τ_rad等光谱参量,测量得到了不同Yb³⁺离子掺杂浓度下玻璃样品的Tm³⁺离子上转换发光谱.结果显示,在980 nm泵浦光激励下玻璃样品发射出强烈的近红外上转换荧光.对Tm³⁺离子上转换发光分析表明,强烈的Tm³⁺离子近红外上转换发光主要来自于Yb³⁺/Yb³⁺离子间的共振能量传递以及基于单声子和双声子辅助的Yb³⁺/Tm³⁺离子间的非共振能量传递过程,并进一步计算得到了声子贡献比和能量传递系数.最后,计算分析了Tm³⁺:³F₄→³H₆能级间跃迁的1.8 μm波段吸收截面、受激发射截面和增益系数.研究表明,Yb³⁺/Tm³⁺共掺TeO₂-ZnO-Na₂O玻璃可以作为近红外波段固体激光器的潜在增益基质.     

Nd:YAG陶瓷与单晶4F3/2–4I13/2跃迁的弱谱线多波长激光性能对比

报道了基于半导体激光端面抽运Nd:YAG的⁴F_3/2–⁴I_13/2 跃迁的弱谱线多波长激光输出. 实验对比了透明陶瓷与单晶材料的激光输出特性, 表明透明陶瓷和单晶材料荧光谱强度的略微差异, 导致了多波长输出时相同两个波长之间的激光强度比在两种材料中的差异. 基于两种耦合输出镜片, 激光阈值都在2 W左右. 在13.5 W的抽运功率下, 基于Nd:YAG透明陶瓷获得了输出功率4.05 W、强度比1 :2的1338与1356 nm双波长激光和输出功率3.65 W、强度比13 : 1的1356与1414 nm 双波长激光, 斜率效率分别达33.9% 和31.9%.     

Continuous wave operation of singly-doped Ho:LSO laser at room temperature

We present the room-temperature continuous-wave Ho:LSO laser single-pass-end-pumped by a diode-pumped Tm:YLF laser at 1.91 μm in this paper. Under different output couplers of 2.4, 5.0, and 14.0%, the laser output power and output spectrum of Ho:LSO laser operating at room temperature are investigated. The output wavelength of Ho:LSO laser was centered at 2106.5 nm with linewidth (FWHM) of about 3.2 nm. With T = 5.0%, the maximum output power of 2.4 W was achieved under the absorbed pump power of 11.1 W, corresponding to a slope efficiency of 38.0%.     

Highly-Efficient Ho:S<Subscript>i</Subscript>Sc<Subscript>2</Subscript>O<Subscript>5</Subscript> Laser Pumped by a Narrow Line-Width Tm:YAP Laser at 1.94 <Emphasis Type="Italic">μ</Emphasis>m

We present a highly-efficient continuous-wave Ho:SSO laser pumped by a diode-pumped Tm:YAP laser with a narrow linewidth (NL) of 0.3 nm. With the free-running (FR) Tm:YAP laser, we obtain a maximum output power of 2.23 W at an absorption pump power of 7.2 W, corresponding to an optical conversion efficiency of 31% and a slope efficiency of 42.6%. With the NL Tm:YAP laser, we obtain a maximum output power of 2.88 W at the same absorption pump power. The optical conversion efficiency increases to 40% when the slope efficiency increases to 55.5%. The output linewidth of the Ho:SSO laser is 0.8 nm when we use the Tm:YAP laser with a narrow linewidth of 1.8 nm pumped by a FR Tm:YAP laser. The beam quality also changes from 1.31 to 1.22.     

Diode-pumped high-efficiency passively Q-switched Yb:CaYAlO<Subscript>4</Subscript> laser

We experimentally demonstrated a high-efficiency passively Q-switched Yb:CaYAlO₄ (Yb:CYA) laser based on a semiconductor-saturable absorber mirror (SESAM), and the output characteristics of the laser including the average output power, repetition frequency, pulse duration, pulse energy and pulse peak power were investigated by adopting output mirrors with different transmittances. When the transmittance of the output mirror was 5% and the pump power was set at about 7.76 W, a maximum average output power of as high as 2.480 W was achieved with a slope efficiency and light-to-light efficiency of the Q-switched Yb:CYA laser of up to 37.1% and 31.2%, respectively.     

Study of RF Excited CO 2 Waveguide Laser Array

Ｉｎｔｒｏｄｕｃｔｉｏｎ　　ＴｈｅＲＦｅｘｃｉｔｅｄｔｅｃｈｎｉｑｕｅｔｏＣＯ２ｗａｖｅｇｕｉｄｅｌａｓｅｒｈａｓｂｅｅｎｒａｐｉｄｌｙｉｍｐｒｏｖｅｄ．ＭａｎｙｎｅｗｓｔｒｕｃｔｕｒｅｓｈａｓａｐｐｅａｒｅｄｓｉｎｃｅＫ．Ｄ．Ｌａａｋｍａｎ［１］ｍａｄｅｆｉｒｓｔｌｙｏｕｔｔｒａｎｓｖｅｒｓｅｅｘｃｉｔｅｄｗａｖｅｇｕｉｄｅＣＯ２ｌａｓｅｒｆｉｒｓｔｉｎ１９７７,ｓｕｃｈａｓｃｏｈｅｒｅｎｔｐｈａｓｅｌｏｃｋｅｄ１×２ａｒｒａｙＣＯ２ｗａｖｅｇｕｉｄｅｌａｓｅｒｇｉｖｅｎｂｙＤ．Ｇ．Ｙｏｕｍ…     

Laser diode and pumped Cr:Yag passively Q-switched yellow-green laser at 543 nm

Efficient and compact yellow green pulsed laser output at 543 nm is generated by frequency doubling of a passively Q-switched end diode-pumped Nd:YVO₄ laser at 1086 nm under the condition of sup-pressing the higher gain transition near 1064 nm. With 15 W of diode pump power and the frequency doubling crystal LBO, as high as 1.58 W output power at 543 nm is achieved. The optical to optical conversion efficiency from the corresponding Q-switched fundamental output to the yellow green output is 49%. The peak power of the Q-switched yellow green pulse laser is up to 30 kW with 5 ns pulse duration. The output power stability over 8 hours is better than 2.56% at the maximum output power. To the best of our knowledge, this is the highest watt-level laser at 543 nm generated by frequency doubling of a passively Q-switched end diode pumped Nd:YVO₄ laser at 1086 nm.     

CONTINUOUS-WAVE LASER OSCILLATION OF Yb:FAP CRYSTALS AT A WAVELENGTH OF 1043nm

A continuous-wave laser oscillation was demonstrated with a Yb-doped fluorapatite (FAP) crystal pumped with a 905 nm Ti:sapphire laser. The output characteristics for different output couplers were investigated. A maximum power of 67mW at a 1043nm wavelength was obtained with 10% output coupler, pumped by a Ti:sapphire laser with 910mW power. This corresponds to a slope efficiency of 26.5%.     

Stable High Power and High Beam Quality Diode-Side-Pumped Continuous-Wave Intracavity Frequency-Doubled Nd:YAG Laser

We report a stable high power and high beam quality diode-side-pumped cw green laser from intracavity frequency-doubled Nd： YAG laser with KTP. By using a L-shaped concave-convex resonator, designed with two Nd：YAG rods birefringence compensation, a large fundamental mode size in the laser crystal and a tight focus in the nonlinear crystal could be obtained simultaneously. The green laser delivers a maximum 532nm output power of 23.2 W. Under 532nm output power of 20.9 W, the beam quality factor is measured to be 4.1, and the fluctuation of the output power is less than 1.4% in an hour.     

Numerical simulation of a CW-pumped Cr:YAG passively Q-switched Yb:YAG pulsed laser

A general model of a CW-pumped passively Q-switched laser is presented which considers the pump power and excitation state of the absorber. The recovery time of the absorber is affected by the Q-switched laser pulse length and repetition rate, which results in changes of the output power, peak power and pulse duration of a CW-pumped passively Q-switched solid-state laser. At low pump power, the final inversion population density alters slowly by a small amount and the effect of the absorber's finite recovery time on laser output energy can be ignored. At high pump power, the final inversion population density increases quickly with pump power increase and the output energy decreases greatly. Simulation results of a CW-pumped, Cr:YAG Q-switched, Yb:YAG laser are reported. The numerical simulation results agree with the theoretical analytical analysis.     

Experimental study on injection-locked Ti:sapphire lasers

An injection-locked Ti:sapphire laser is developed,with injection locking achieved using the Pound-DreverHall technique.By measuring the dependence of output power on the pump power with various Ti:sapphire laser parameters,we experimentally studied the influences of the ring cavity length,the focal length of the pump-laser mode-matching lens,and the output-coupler transmission on the threshold and slope efficiency.The dependence of the output power on the master laser power is also investigated.The present study provides a guideline for developing a Ti:sapphire laser with high slope efficiency and low threshold.