Color changes in CR-39 nuclear track detector by gamma and laser irradiation

A study of the effect of gamma and laser irradiation on the color changes of polyallyl diglycol (CR-39) solid-state nuclear track detector was performed. CR-39 detector samples were classified into two main groups. The first group was irradiated with gamma doses at levels between 20 and 300 kGy, whereas the second group was exposed to infrared laser radiation with energy fluences at levels between 0.71 and 8.53 J/cm². The transmission of these samples in the wavelength range 300–2500 nm, as well as any color changes, was studied. Using the transmission data, both the tristimulus and the coordinate values of the Commission Internationale de l'Eclairage (CIE) LAB were calculated. Also, the color differences between the non-irradiated samples and those irradiated with different gamma or laser doses were calculated. The results indicate that the CR-39 detector acquires color changes under gamma or laser irradiation, but it has more response to color changes by gamma irradiation. In addition, structural property studies using infrared spectroscopy were performed. The results indicate that the irradiation of a CR-39 detector with gamma or laser radiations causes the cleavage of the carbonate linkage that can be attributed to the ?H abstraction from the backbone of the polymer, associated with the formation of CO₂ and ?OH with varying intensities.     

Effects of gamma radiation on hard dental tissues of albino rats using scanning electron microscope – Part 1

In the present study, 40 adult male albino rats were used to study the effect of gamma radiation on the hard dental tissues (enamel surface, dentinal tubules and the cementum surface). The rats were irradiated at 0.2, 0.5, 1.0, 2.0, 4.0 and 6.0 Gy gamma doses. The effects of irradiated hard dental tissues samples were investigated using a scanning electron microscope. For doses up to 0.5 Gy, there was no evidence of the existence of cracks on the enamel surface. With 1 Gy irradiation dose, cracks were clearly observed with localized erosive areas. At 2 Gy irradiation dose, the enamel showed morphological alterations as disturbed prismatic and interprismatic areas. An increase in dentinal tubules diameter and a contemporary inter-tubular dentine volume decrease were observed with higher irradiation dose. Concerning cementum, low doses,<0.5 Gy, showed surface irregularities and with increase in the irradiation dose to≥1 Gy, noticeable surface irregularities and erosive areas with decrease in Sharpey's fiber sites were observed. These observations could shed light on the hazardous effects of irradiation fields to the functioning of the human teeth.     

Surface free energy of ultra-high molecular weight polyethylene modified by electron and gamma irradiation

Surface free energy of biocompatible polymers is important factor which affects the surface properties such as wetting, adhesion and biocompatibility. In the present work, the change in the surface free energy of ultra-high molecular weight polyethylene (UHMWPE) samples, which is produced by electron beam and gamma ray irradiation were, investigated. Mechanism of the changes in surface free energy induced by irradiations of doses ranging from 25 to 500 kGy was studied. FTIR technique was applied for sample analysis. Contact angle measurements showed that wettability and surface free energy of samples have increased with increasing the irradiation dose, where the values of droplet contact angle of the samples decrease gradually with increasing the radiation dose. The increase in the wettability and surface free energy of the irradiated samples are attributed to formation of hydrophilic groups on the polymer surface by the oxidation, which apparently occurs by exposure of irradiated samples to the air.     

Gamma induced changes in the structural and optical properties of Makrofol LS 1–1 polycarbonate

ABSTRACT

Samples from sheets of the polymeric material Makrofol LS 1–1 have been exposed to gamma radiation in the dose range 10–250?kGy. The modifications induced in Makrofol samples due to gamma irradiation have been studied through different characterization techniques such as intrinsic viscosity as a measure of the average molecular mass, Fourier Transform Infrared spectroscopy FTIR, refractive index and color difference studies. The results indicate that the crosslinking dominates at the dose range 50–250?kGy. The crosslinking reported by viscosity measurements is supported by the trend of the function groups present in the sample with the gamma dose. Also, the increase in intrinsic viscosity indicating an increase in the average molecular mass was associated with an increase in the refractive index. Additionally, the non-irradiated Makrofol samples showed significant color sensitivity towards gamma irradiation. The color intensity ΔE, which is the color difference between the non-irradiated sample and those irradiated with different gamma doses, increased (0–5.56) with increasing the dose up to 250?kGy, convoyed by an increase in the red and yellow color components.     

Gamma-photon induced modifications in Polyvinylchloride (PVC) film

Gamma photon induced modifications in Polyvinylchloride (PVC) polymer have been studied in the dose range of 10¹-10⁶Gy at room temperature. Polyvinylchloride films have been irradiated with different doses of gamma radiation from a ⁶⁰Co source. To monitor the chemical and structural changes caused by gamma radiation IR and UV-Vis spectroscopy of pristine and irradiated PVC have been performed and using the spectral data some changes in the properties have been investigated. The spectral studies have indicated that at a dose of 10⁶Gy scissioning of the C-a bonds takes place. This scissioning of the chain initiates decomposition at a lower temperature. Thermal stability of the polymer reduces due to irradiation but the decomposition patterns remain the same. The optical band-gap is found to decrease due to irradiation at doses bigher than 10³Gy.     

Structural,electrical and optical properties of gamma irradiated methyl para-hydroxy benzoate single crystals

ABSTRACT

Nonlinear optical materials (NLO) have been garnering attention due to their role in optical data storage, optical communication and laser technology. Organic crystals have emerged as an extremely important class of NLO materials, since their NLO properties compare very well with traditional inorganic NLO materials like KCl, LiNbO₃, KDP (potassium dihydrogen phosphate), etc. They offer the additional advantage that they can be grown relatively inexpensively from solution close to room temperature, unlike the inorganic NLO materials which are grown from high temperature melts. In the present work, organic transparent single crystals of methyl para-hydroxy benzoate (MHB) were grown by slow evaporation solution growth technique (SEST) from aqueous solution at room temperature. The changes in structural, electrical and optical properties of gamma irradiated MHB single crystals were studied using X-ray diffraction (XRD), UV–Visible absorption spectroscopy, Photo-luminescence (PL), Fourier transform infrared (FTIR) spectroscopy and AC conductivity measurements at room temperature. The polished MHB single crystals were irradiated with gamma rays of doses 10 and 15 kilogray (kGy). From the XRD analysis, it was observed that gamma irradiation for these doses drastically decreases the crystallinity. The optical absorption constants were examined by UV-Visible absorption spectroscopy, measured over the wavelength range of 200–800?nm, at normal incidence. The optical band gap as estimated from the Tauc plot ((αhν)² vs hν) was found to be reduced with increasing gamma irradiation doses. PL spectra showed emission at wavelengths of 361?nm (3.43?eV) and 452?nm (2.74?eV), with enhanced intensities for the irradiated crystals. FTIR spectroscopy was utilised to identify the functional groups of MHB and indicated the rupture of specific types of bonds with gamma irradiation. Apart from that, the enhancement of AC conductivity with gamma irradiation was also observed for the gamma irradiated crystals.     

FT-IR spectroscopy assessment of aesthetic dental materials irradiated with low-dose therapeutic ionizing radiation

The aim of the present study was to evaluate the effects of low-dose therapeutic ionizing radiation on different aesthetic dental materials. Forty five specimens (n = 45) of three different aesthetic restorative materials were prepared and randomly divided into five groups: G1 (control group); G2, G3, G4, G5 experimental groups irradiated respectively with 0.25, 0.50, 0.75, and 1.00 Gy of gamma radiation by the ⁶⁰Co teletherapy machine. Chemical analyses were performed using a FT-IR Nicolet 520 spectrophotometer with reflectance diffuse technique. Even a minimal exposition at ionizing radiation in therapeutic doses can provide chemical changes on light-cured composite resins. The three studied restorative materials showed changes after exposure at gamma radiation, however the increase of the radiation dose did not contribute to an increase in this effect.     

Use of optical properties of LiF in radiation protection dosimetry

Optical absorption spectra of LiF:Mg, Ti thermoluminescence (TL) materials have been determined and used in radiation absorbed dose measurements. Samples were irradiated with different gamma doses (0???1.022 Gy) with dose rate of 12.78 mGy/min and also for different X-ray beam qualities. It was found that there is no significant absorption edge, and the optical absorption increases with increasing gamma doses. Peak intensities of trapping levels showed a linear increase with increasing X-ray or gamma doses. The variation of the optical density with X-ray or gamma doses is energy independent. The TL readings were not affected when the samples were first measured optically. The linearity of the optical density–dose relationship is found to be useful in radiation protection dosimetry.     

X-ray irradiation-induced changes in Bayfol DPF 5023 polycarbonate

Samples from sheets of the polymeric material Bayfol DPF 5023 have been exposed to X-ray radiation in the dose range 100–2300 Gy. The modifications induced in Bayfol samples due to X-ray irradiation have been studied through different characterization techniques such as X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, intrinsic viscosity, refractive index and color difference studies. The infrared spectroscopy indicated that crosslinking is the dominant mechanism at the dose range of 200–2300 Gy. The crosslinking reported by FTIR spectroscopy destroyed the degree of ordering in the Bayfol samples, as revealed by the XRD technique. Also, this crosslinking led to an increase in the value of intrinsic viscosity from 0.54 for the non-irradiated sample to 0.63 for the sample irradiated with 2300 Gy at 30 °C, indicating an increase in the average molecular mass. This was associated with an increase in the refractive index. Additionally, the non-irradiated Bayfol samples showed significant color sensitivity toward X-ray irradiation. This sensitivity appeared in the change of the blue color component of the non-irradiated Bayfol film to yellow after exposure to X-ray doses up to 2300 Gy. This is accompanied by a net increase in the darkness of the samples.     

Spectroscopic and thermal studies of gamma irradiated polypropylene polymer

Thin films of polypropylene have been irradiated with different doses of gamma radiation from a ⁶⁰Co source. IR, UV-VIS spectra of this polymer before and after irradiation have been recorded and from the spectral data some modifications in the properties have been investigated. The spectra indicated that polypropylene film was oxidised at the dose of 10⁶ Gy. Due to the removal of additives, total destruction of the polymer takes place at this dose. Isotactic arrangement of the polymer is no longer present after irradiation. Growth of carbon cluster takes place above a gamma dose of 10² Gy. Thermal stability of the polymer changes due to irradiation and the polymer seems to decompose in four different steps at the highest dose of 10⁶ Gy.     

A study on the best irradiation dose of X-ray for Hep-2 cells by Fourier transform infrared spectroscopy

Fourier transform infrared spectroscopy (FTIR) was employed to study the human epidermis larynx carcinoma cell lines (Hep-2) which were irradiated by different doses of X-ray.The results show that (1) the irradiation of X-ray damages the structure of the CH3 groups of the thymine in DNA,which restrains the reproduction of Hep-2 cells effectively,(2) the 8 Gy dose of X-ray irradiation changes the framework and the relative contents of some proteins,lipids and the nucleic acid molecules intercellular in the greatest degree,and (3) the 8 Gy dose of X-ray irradiation is the best irradiation dose for lowering the degree of the cancerization of Hep-2 cells according to the criteria for the degree of the cancerization reported recently.Meanwhile,the apoptosis of these cells were detected by using flow cytometry (FCM) primarily.It shows that the apoptotic ratio of the Hep-2 cells depends on the irradiation dose to some extent,but is not linearly.And the apoptotic ratio of the 12 Gy dose group is the maximum (20.36%),but the apoptotic ratios of the 2 to 8 Gy dose groups change little.     

12C6+束辐照引起的实验猪皮肤急性损伤反应的研究

探讨了正常皮肤对重离子辐照急性损伤反应的耐受性, 为重离子治癌临床应用提供安全性检测的实验依据。实验前10 min, 实验猪肌肉注射复方氯胺酮1.2 mg/kg进行麻醉, 然后在兰州重离子研究装置（HIRFL）辐照终端利用12C6+束照射, 辐照剂量分别为0, 12, 21和27 Gy, 辐照分3次完成, 剂量率约为1.2 Gy/min, Bragg峰区照射, 辐照后每隔7 d对照射野拍照并活检取样, 做HE组织病理学观察。不同剂量12C6+离子束辐照实验猪皮肤后, 皮肤外观反应随辐照剂量增大而加快, 表现为肿胀和色素沉积等; 皮肤组织结构的变化明显, 上皮细胞排列紊乱、 萎缩、 空泡变性; 基本恢复正常所需时间也越长, 且都存在明显的剂量效应关系。结果表明, 辐照剂量范围为0—27 Gy时, 重离子对正常皮肤的辐照是安全的。The tolerance of the normal skin to the acute radiation injury reaction induced by heavy ion beams has been studied experimentally. The experimental pigs were injected with 1.2 mg/kg ketamine in 10 min before irradiation and were irradiated with 0, 12 , 21 and 27 Gy 12C6+ ion at a dose rate of 1.2 Gy/min at the Heavy Ion Research Facility in Lanzhou（HIRFL）. The total radiation dose was finished by 3 times at Bragg Peak Region of Heavy Ion Beams.The radiation fields of skin were taken photo and performed biopsy. The contaneous tissues of radiation fields were stained by HE and examined histopatholo gical changes every seven days after irradiation. The results indicated that the cutaneous appearance reaction became more faster with radiation dosage rising and presented with swollen, melanin forming and so on after irradiated by the carbon ions at different dosage. The Pathological examination showed noticeable changes in histological and structural of experimental pigs skin, such as atrophy, vacuolation, denaturation and arranged irregularly in epithelial cells. Furthermore, the time for return to normality became longer with the increasing of radiation dosage. All indexes demonstrated correlation between the does and effects. It is concluded that the irradiation of heavy ion beams to normal skin is security when the radiation dose range is about 0—27 Gy.     

Modification induced by gamma irradiation in Bayfol CR 1-4 polycarbonate

Bayfol CR 1-4 polycarbonate is a class of polymeric solid state nuclear track detector which has many applications in various radiation detection fields. Samples from sheets of Bayfol have been irradiated with gamma doses ranging from 100 to 620 kGy. The structural modifications in the gamma-irradiated Bayfol samples have been studied as a function of dose, using different characterization techniques such as X-ray diffraction (XRD), Fourier-transform infrared (FTIR) spectroscopy, intrinsic viscosity and refractive index. The results indicate that the carbonyl group (C?O) degraded under irradiation up to 200 kGy. This degradation, reported by FTIR spectroscopy enhanced the degree of ordering in the degraded samples as revealed by the XRD technique. Above 200 and up to 620 kGy, cross-linking is achieved, leading to an increase in the intrinsic viscosity from 0.41 to 0.78 at 35°C, indicating an increase in the average molecular mass. On the other hand, the resultant effect of gamma irradiation on the thermal properties of Bayfol has been investigated using thermo-gravimetric analysis, results indicating that the gamma irradiation in the dose range 200–620 kGy led to a more compact structure of Bayfol polymer, which resulted in an improvement in its thermal stability with an increase in the activation energy of thermal decomposition due to cross-linking. In addition, the V–I characteristics of the polymer samples were performed, results indicated that at higher voltage, the conduction mechanism of Bayfol CR 1-4 was identified as the Poole–Frenkel type.     

A study of the effect of gamma and laser irradiation on the thermal,optical and structural properties of CR-39 nuclear track detector

A comparative study of the effect of gamma and laser irradiation on the thermal, optical and structural properties of the CR-39 diglycol carbonate solid state nuclear track detector has been carried out. Samples from CR-39 polymer were classified into two main groups: the first group was irradiated by gamma rays with doses at levels between 20 and 300 kGy, whereas the second group was exposed to infrared laser radiation with energy fluences at levels between 0.71 and 8.53 J/cm². Non-isothermal studies were carried out using thermogravimetry, differential thermogravimetry and differential thermal analysis to obtain activation energy of decomposition and transition temperatures for the non-irradiated and all irradiated CR-39 samples. In addition, optical and structural property studies were performed on non-irradiated and irradiated CR-39 samples using refractive index and X-ray diffraction measurements. Variation in the onset temperature of decomposition T _o, activation energy of decomposition E _a, melting temperature T _m, refractive index n and the mass fraction of the amorphous phase after gamma and laser irradiation were studied.

It was found that many changes in the thermal, optical and structural properties of the CR-39 polymer could be produced by gamma irradiation via degradation and cross-linking mechanisms. Also, the gamma dose has an advantage of increasing the correlation between thermal stability of the CR-39 polymer and bond formation created by the ionizing effect of gamma radiation. On the other hand, higher laser-energy fluences in the range 4.27–8.53 J/cm² decrease the melting temperature of the CR-39 polymer and this is most suitable for applications requiring molding of the polymer at lower temperatures.     

EPR and UV spectrometry investigation of sucrose irradiated with carbon particles

Solid state/EPR (SS/EPR) dosimeters of carbon ions irradiated sucrose are studied with EPR, and their water solutions – with UV spectroscopy. Doses between 20 and 200 Gy are used with linear energy transfer (LET) values for carbon ions of 63, 77, 96 and 230 keV μm^?1. After irradiation all samples show typical for irradiated sucrose EPR and UV spectra. The obtained data are compared with those previously reported for nitrogen particles and gamma rays irradiated sucrose. The identical shape of both the EPR and UV spectra of irradiated with various type radiation samples suggests that generated free radicals are not influenced by the nature of radiation. The lack of difference in the line width of the separate lines or the whole EPR spectrum, obtained for gamma and heavy particles irradiation, suggests negligible spin–spin interaction among the radiation-generated free radicals in the samples. The linear dependence of the EPR response on the absorbed dose radiation is found to be higher when generated by gamma rays, than by the same absorbed dose of heavy particles. In addition, the EPR response for carbon ions is higher than that for nitrogen ions. Water solutions of irradiated sucrose exhibit UV spectrum with absorption maximum at 267 nm, attributed to the recombination products of free radicals. The UV band intensity depends on the absorbed dose radiation. The UV spectra obtained for carbon, nitrogen and gamma rays irradiated sucrose are also compared.     

Modifications induced by gamma irradiation upon structural,optical and chemical properties of polyamide nylon-6,6 polymer

The effects of gamma rays were studied on the optical, structural and chemical properties of the PA-66 polymer samples. The polymer samples obtained from Goodfellow (Cambridge, UK) were irradiated with gamma rays at various doses ranging from 100 to 1250 kGy. The pristine and gamma rays irradiated samples were characterized by UV–visible (UV–VIS) spectroscopy, X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy. UV–VIS shows a shift in absorption toward the visible region for irradiated samples and a decrease in band gap energy (E_g). The XRD analyses show an increase in the crystalline nature of the polymer at higher doses as a result of significant decrease in the peak width of XRD patterns. The FTIR spectra show decrease in intensity and shift of various bands with increase in gamma dose.     

Feasibility of radiation sterilization and dosimetric features of ampicillin: an electron spin resonance study

In the present work, it was aimed to identify radical species produced by gamma irradiation (3–34?kGy) of solid ampicillin, to determine its spectroscopic, dosimetric, stability and kinetic behavior, and to investigate feasibility of the radiation sterilization feature of ampicillin by using electron spin resonance (ESR) spectroscopy. ESR experiments were performed at low and high temperatures (130–400?K) to examine the characteristic properties of the radical intermediates that are produced in ampicillin by gamma radiation treatment. Unirradiated ampicillin presented no ESR signal but irradiated samples exhibited ESR spectra with four resonance peaks spread over a magnetic field range of 8?mT. The spectral parameters of the central resonance line of the spectrum are g?=?2.0044 and ΔH_pp?=?0.08?mT. An exponential growth function of the applied dose was found to describe best the experimental dose–response data and it was found that ampicillin did not exhibit the feature of a good dosimetric material as its ESR intensity was relatively weak even for the samples irradiated at high level of doses. G_mean value of gamma-irradiated ampicillin was found to be 4.6?±?0.9?×?10^?9?mol/J, which is very small compared to irradiated alanine solid sample. However, the discrimination of irradiated ampicillin from unirradiated one was possible even ～3 months after storage at normal conditions. The simulation calculations indicated that gamma irradiation created two different radical species in solid ampicillin. Decay activation energy of the radical species which is mostly responsible from central intense resonance line is calculated to be 55.6?±?3.2?kJ/mol by using the signal intensity decay data derived from annealing studies. It was concluded that ampicillin could be sterilized by gamma radiation and ESR spectroscopy can be used as a potential technique to monitor its radiosterilization process.     

Radiation annealing of rapidly solidified Sn–6.7Sb–5.3Zn alloy by low-dose gamma ray

The radiation annealing of a rapidly solidified Sn–6.7Sb–5.3Zn (in atomic percent) melt-spun alloy was caused by low-dose gamma ray irradiation. This is observed from the increase in both the volume of unit cell and particle size of the Sn matrix, as revealed from X-ray diffraction analysis, and the decrease in the resistivity. The alloy was irradiated by gamma ray at doses 5, 10, 20, 40, 50, 60, 70, 80, and 100 Gy. The electrical resistivity was measured for the alloys subjected to these doses and it was found that the resistivity decreased by increasing the dose to a minimum value of 50 Gy and then increased by increasing the dose.     

TL and PTTL in natural fluorite previously irradiated with gamma rays and heavy ions

The effect of annealing temperature on the phototransfer thermoluminescence (PTTL) signal was studied to determine the appropriate annealing temperature for treating the natural powder before irradiation. The temperatures used to anneal virgin natural fluorite samples (only natural dose without giving the samples any artificial doses) were 150, 250, 350, 450, 550, 650 and 750°C for a duration of 1 h in each case. The results show that the PTTL response did not change for anneal temperatures up to 450°C, but at higher temperatures the signal decreased rapidly. The height of the 90°C peak decreased by two orders of magnitude as the anneal temperature increased from 450 to 750°C, whilst the height of the 180°C peak decreased by three orders of magnitude between the same two annealing temperatures. In order to investigate the effect of previous gamma rays and heavy ion irradiation on thermoluminescence (TL) and PTTL signals, powdered samples of natural fluorite from Cornwall, England, were annealed at 500°C and then irradiated (at GSI, Darmstadt, Germany) with ¹⁶¹Dy ions of energy 13 Mev/n; the range of fluences used was from 10⁴ to 10¹² ion cm⁻². Identical samples were given gamma doses in the range 1 Gy to 2.6 × 10⁴ Gy in order to compare the effects of gamma rays and heavy ions. The sensitivities of TL and PTTL were studied by giving the samples a gamma test dose of 1 Gy after annealing the samples at 500°C for 30 min in order to eliminate the TL resulting from previous gamma or heavy ion irradiation.     

Gamma-irradiation effect on a commercial composite anticorrosive pigment and acidity-to-alkalinity conversion

A commercial composite anticorrosive pigment based on aluminum dihydrogen tripolyphosphate was studied after exposure to gamma irradiation (Co⁶⁰, 0, 20, 50, 100 and 150?kGy) using FTIR, XRD, TGA and acid-base titration technologies. Although the FTIR spectra showed that the effect of the irradiation on functional groups in the pigments was not obvious, the decrease in the crystal lattice parameters of the irradiated pigments was observed in the XRD spectra compared to the non-irradiated sample. But the extent of the lattice parameter decrease monotonically with the increase of absorbed dose from 20 to 150?kGy, which was attributed to the decomposition of water and the simultaneous occurrence of lattice damage when the pigments were exposed to gamma rays. Of particular significance was the displayed basicity of the aqueous solutions of the irradiated pigments compared to the acidity of the solution of the non-irradiated pigment, which was attributed to the decomposition of P-OH groups (combined water).