两个光纤激光器的互相注入锁定

光纤激光器的相干合成技术是实现高功率、高亮度光纤激光系统的重要技术途径.利用分束器分光使两个光纤激光器的能量互相注入，从而使两个光纤激光器达到锁相锁模实现相干输出. 实验研究表明：在独立运行的情况下，两个光纤激光器的远场光斑只是两个激光器光强的简单叠加；在互相注入锁定的情况下，两个光纤激光器的远场光斑是具有高对比度的干涉条纹，并得到两个激光器的输出模式总为异相模.这与理论分析的结果相一致. 关键词： 光纤激光器 相干合成 锁相     

光纤激光器自组织相干阵列的理论分析

 分析了光纤激光器自相干阵列最简单的情况——两个光纤激光器之间的相位锁定过程。建立了该过程的数学模型，并对它的时间特性和输出光束的模式进行了理论和数值分析，讨论了运行频率差和耦合系数对锁相过程的影响。对于运行频率相等的两个光纤激光器，当两个光纤激光器初始相位差不为0时，相位锁定后的激光器阵列输出模式为异相模；对于运行频率不等的情形，给出了锁相运行对两个光纤激光器运行频率差的要求，并分析了降低这种要求的几种方法。     

两路双包层光纤激光器互注入锁相实验研究

提出了一种利用45°半透半反分束镜和角锥反射器实现两路光纤激光器的能量相互注入,从而获得相干合成激光输出的新方法,分析了其锁相原理.在实验上成功实现了两路独立振荡双包层光纤激光器的互注入锁相输出,在远场观察到了清晰稳定的干涉条纹（可见度约0.57）,获得了超过10W的相干合成激光输出,功率合成效率约为76%.实验表明,这种互注入锁相方法可以在更高功率条件下运行,是光纤激光相干合成领域一种有前途的新技术. 关键词： 光纤激光器 相干合成 互注入锁相     

1018 nm短波长掺镱光纤激光高功率自组织相干合成

搭建了两台高功率、低量子损耗的1018 nm短波长掺镱光纤激光器,进行了全光纤结构下两路光纤激光器的相干合成实验。获得了功率为55 W、合成效率为90.2%的相干输出,这是当前严格单模1018 nm光纤激光器的最高功率水平。同时,验证了Michelson腔自组织相干合成技术能够实现光纤激光器的高功率单模输出。     

两路关联光纤激光器互注入锁相实验

基于角锥互注入锁相相干合成方案,利用光纤Bragg光栅（R=85％@1064nm）作为两路光纤激光器的共用腔镜,实现了两路光纤激光器相关联,进一步提高了激光的互注入能量。采用外腔结构,较容易实现了两路光纤激光器的能量互注入锁相。在实验上观察到了远场清晰稳定的干涉条纹（可见度超过0．8）,获得了功率合成效率约为80％的线偏振相干激光输出。     

子激光器功率差对光纤激光器相干组束的影响

设计了由两支光纤激光器通过耦合器组成的迈克尔逊腔型光纤激光器阵列,实现了相干合成输出,相干合成功率与完全相干合成的理论值偏差约9％。研究了子激光器功率差对低损耗端口相干合成特性的影响。结果表明：当子光纤激光器功率差减小时,耦合效率增大,理论与实验偏差减小,泵浦效率增大,输出功率增大,光谱中心波长基本不变;子激光器功率越大,子激光器功率差对以上物理量的影响越小。     

利用全光纤结构Michelson腔实现两路高功率双包层光纤激光器相干合成

Michelson腔技术是实现激光相干合成的有效方案. 利用Michelson腔技术, 实现了全光纤结构下的两路光纤激光器的相干合成, 获得了功率为11.75 W, 效率为95.76%的相干输出. 实验研究了相干合成效率与激光腔长差的关系以及抽运对称性对相干合成效率的影响. 实验表明相干合成效率极易受激光腔长差的影响, 不同腔长差下相干合成效率差异可达18%以上, 且存在最佳腔长差; 抽运对称性对相干合成效率的影响在2%以内.     

半导体光放大光纤环形激光器的偏振混沌与相干性

研究了基于半导体光放大器(SOA)的光纤环形激光器的偏振混沌光的特性及其相干性。实验采集激光器的输出功率和偏振度,得到了基于半导体光放大器的光纤环形激光器的输出从自发辐射到受激辐射、再到偏振态混沌激光辐射的演化过程。利用马赫-曾德尔(M-Z)干涉仪验证了混沌激光的相干性,并发现混沌干涉只有零级。测量不同光程差时干涉仪的输出功率,计算相应的干涉条纹可见度,进一步算得混沌激光的相干时间约为40 ps。这一结果与根据光谱计算的该混沌激光的相干时间43 ps基本一致。实验还测得该混沌激光的相干性与半导体光放大器的电流无关。并指出了混沌激光相干应用于低相干光源探测领域的灵敏度和分辨力优势。     

多芯光纤激光器增益场选模效应研究

对多芯光纤激光器的增益场选模效应进行了初步研究。利用矢量耦合模理论计算多芯光纤激光器支持的各类超模的模式特性,并对其增益系数进行计算,比较不同功率等级下各超模增益特性的异同。计算结果表明,在较低功率下。多芯光纤激光器各类超模增益系数大小基本一致,输出光束是由各超模组成的混合模式; 而当激光功率较高时,同相模的增益系数大小明显大于其它模式,在模式竞争中占据优势,激光器输出光束远场具备同相模的特征。最后对多芯光纤激光器增益场选模效应的适用范围进行了简单讨论。     

激光器的部分相干性对光纤激光器阵列相干合成远场图样的影响

考虑光纤激光器阵列相干合成的远场分布时，一般都认为单个激光器的输出光束是理想的高斯光束，实际上受各种因素的影响，一般激光器的输出光束都是一部分相干光.从部分相干光的高斯-谢尔模型出发，首次推导出了当单个激光器的输出光束是部分相干光时，激光器阵列相干合成的远场光强分布模型，并给出了数值模拟计算结果. 关键词： 光纤激光器阵列 相干合成 部分相干光     

基于外差法的光纤激光器相干合成

采用波长1064 nm,功率为1 W的种子激光实现了两路光纤激光的相干合成,采用了两只保偏光纤准直器接收两路光干涉信号,与利用透镜直接把干涉信号会聚在探测器上相比,这种耦合方式得到的光干涉信号的条纹对比度更高。对相位噪声以及相位噪声的带宽进行了研究,结果表明,相位噪声由电信号串扰以及环境扰动产生。通过人为拨动光纤来增加相位噪声带宽,当相位噪声带宽增加时,相位控制精度下降。提出了提高相位控制精度的方法,实验获得了桶中功率为21.3%、斯特列尔比为79%、相位控制精度为0.008的相干合成效果。     

Numerical and experimental study on coherent beam combining of fibre amplifiers using simulated annealing algorithm

We present the numerical and experimental study on the coherent beam combining of fibre amplifiers by means of simulated annealing (SA) algorithm. The feasibility is validated by the Monte Carlo simulation of correcting static phase distortion using SA algorithm. The performance of SA algorithm under time-varying phase noise is numerically studied by dynamic simulation. It is revealed that the influence of phase noise on the performance of SA algorithm gets stronger with an increase in amplitude or frequency of phase noise; and the laser array that contains more lasers will be more affected from phase noise. The performance of SA algorithm for coherent beam combining is also compared with a widely used stochastic optimization algorithm, i.e., the stochastic parallel gradient descent (SPGD) algorithm. In a proof-of-concept experiment we demonstrate the coherent beam combining of two 1083~nm fibre amplifiers with a total output power of 12~W and 93% combining efficiency. The contrast of the far-field coherently combined beam profiles is calculated to be as high as 95%.     

Mutual injection locking and coherent combining of three individual fiber lasers

Mutual injection locking and coherent combining of three individual erbium-doped fiber lasers are reported. Theoretical model of the three fiber lasers under mutual injection is also analyzed. Under free running state, the far field beam profile is a simple intensity superposition as three incoherent beams. Under mutual injection locking, interference lobes with high contrast ratio are obtained in the far field of three fiber lasers, which shows that the three fiber lasers have good interference characteristic under mutual injection. The experimental results are in good agreement with the theoretical results. According to this method, we can also realize coherent beam combining in more fiber lasers.     

Timing Jitter in Amplitude Modulated Harmonically Mode-Locked Er-Doped Fiber Ring Lasers

The phase noise and the amplitude noise of optical pulses from the amplitude modulated harmonically mode-locked (AM-HML) Er-doped fiber (EDF) ring laser was investigated by measuring the power spectra of the optical pulses. The root mean square (RMS) timing jitter and the RMS amplitude noise are 1.26 ps and 2.5% (500 Hz-50 kHz), respectively, when the pulse repetition frequency is 1.58 GHz. They are smaller than those in conventional harmonically mode-locked EDF ring lasers.     

基于公共环形腔耦合的光纤激光器相干合成技术

 为提高光纤激光器无源自调整相干合成阵列的效率、稳定性和可扩展性,提出了基于公共光纤环形腔耦合与单模光纤滤波的光纤激光器相干合成方案。将多个2×2的光纤耦合器分别插入各单元激光器的谐振腔,利用耦合器余下的端口,两两相连构成公共环形耦合腔。采用单模光纤滤波技术,提高了各输出激光束之间相位锁定的稳定性。利用该方案在实验上实现了三路光纤激光器的被动锁相输出,实验测得的远场干涉光斑、输出功率及光谱均表明该方案适于构建性能较好的光纤激光器相干合成阵列。     

Synchronization and coherent combining of two pulsed fiber lasers

We demonstrate a scalable architecture for coherent combining of pulsed fiber lasers.A new method for generating synchronous pulsed fiber lasers by direct phase modulation is proposed and investigated.It is shown that phase modulated mutually coupled laser array can be a steady synchronous pulsed fiber laser source.The synchronous pulsed fiber lasers are coherently combined with an invariable phase difference of π in adjacent lasers.Neither active phase control nor polarization control is taken in our experiment.     

Amplitude to phase conversion of InGaAs pin photo-diodes for femtosecond lasers microwave signal generation

When a photo-diode is illuminated by a pulse train from a femtosecond laser, it generates microwaves components at the harmonics of the repetition rate within its bandwidth. The phase of these components (relative to the optical pulse train) is known to be dependent on the optical energy per pulse. We present an experimental study of this dependence in InGaAs pin photo-diodes illuminated with ultra-short pulses generated by an Erbium-doped fiber based femtosecond laser. The energy to phase dependence is measured over a large range of impinging pulse energies near and above saturation for two typical detectors, commonly used in optical frequency metrology with femtosecond laser based optical frequency combs. When scanning the optical pulse energy, the coefficient which relates phase variations to energy variations is found to alternate between positive and negative values, with many (for high harmonics of the repetition rate) vanishing points. By operating the system near one of these vanishing points, the typical amplitude noise level of commercial-core fiber-based femtosecond lasers is sufficiently low to generate state-of-the-art ultra-low phase noise microwave signals, virtually immune to amplitude to phase conversion related noise.     

谱线和耦合系数对光纤激光器相互注入锁定的影响

相互注入锁定是相干合成技术中最具发展前景的方案之一. 在两个光纤激光器相互注入锁定的基础上,利用可调节光纤光栅改变其中一个激光器的中心谱线和利用不同的分束器改变两个激光器间的耦合系数,同时监测两个激光器的远场光斑和谱线,判断激光器谱线和耦合系数对相互注入锁定的影响. 通过理论和实验得到：提高耦合系数可以提高锁定的频率差;两个激光器的谱线越接近锁定的效果越好,当激光器的谱线超过一定范围时,两个激光器将不能被锁定. 关键词： 光纤激光器 相干合成 相位锁定