Synchronization and coherent addition of three pulsed fiber lasers by mutual injection and phase modulation

The coherent beam addition of pulsed fiber lasers is an effective way to improve the average power and the peak pulse power. We demonstrate a new architecture based on mutual injection and phase modulation to generate synchronous pulsed fiber lasers. Firstly, we realize the synchronization of the pulses of three fiber lasers using this technique. Secondly, coherent addition of three synchronous pulsed fiber lasers is obtained. Experimental results show that the three fiber lasers are phase locked and have good temporal and spatial coherence under mutual injection locking. This method can be extended to combine more beams.     

基于外差法的光纤激光器相干合成

采用波长1064 nm,功率为1 W的种子激光实现了两路光纤激光的相干合成,采用了两只保偏光纤准直器接收两路光干涉信号,与利用透镜直接把干涉信号会聚在探测器上相比,这种耦合方式得到的光干涉信号的条纹对比度更高。对相位噪声以及相位噪声的带宽进行了研究,结果表明,相位噪声由电信号串扰以及环境扰动产生。通过人为拨动光纤来增加相位噪声带宽,当相位噪声带宽增加时,相位控制精度下降。提出了提高相位控制精度的方法,实验获得了桶中功率为21.3%、斯特列尔比为79%、相位控制精度为0.008的相干合成效果。     

Yb-Bi pulsed fiber lasers

A new type of pulsed fiber laser is suggested and developed - Yb-Bi lasers. In such lasers the Yb fiber laser is Q-switched by use of a saturable absorber, a Bi-doped fiber placed in its own resonator, and pulsed lasing is obtained in both fiber lasers. Continous-wave diode-clad pumping of the Yb-Bi lasers at a 975 nm wavelength with power up to 16.5 W results in pulsed laser action in a spectral diapason of 1050-1200 nm with a maximum pulse energy of up to 100 microJ, an average power up to 7.5 W, and a repetition rate up to 100 kHz.     

Coherent beam combining of pulsed fiber lasers with hybrid phase control

We demonstrate a scalable architecture for coherent combining of all-fiber pulsed lasers with hybrid phase control involving passive phasing and active phasing for the first time. Synchronized and passive phased pulsed laser array is built by intra-activity phase modulation. Active phase control on the passive phased pulsed laser array using stochastic parallel gradient descent algorithm provides stable in-phase coherent beam combining pattern in a turbulent atmosphere. The fringe visibility is increased from 0 two 0.43 and the power encircled in the main-lobe is 1.616 times increased when the system evolves from passive phasing to hybrid phasing. The architecture can be easily scaled up to high power by increasing power of each individual laser, number of laser elements and introduction of power amplifiers, which will lead a promising way for scaleable high power coherent beam combining of pulsed lasers.     

32路光纤激光相干阵列的相位锁定

报道了32路光纤激光相干阵列的相位锁定实验研究。搭建了32路光纤激光相干阵列实验系统,基于现场可编程逻辑阵列(FPGA)设计制作了高速高精度相位控制器。当相位控制器执行随机并行梯度下降(SPGD)算法对各路激光的相位进行锁定时,相干阵列输出的激光功率与不进行相位锁定时相比提高了约26倍。     

Coherent beam combination of adaptive fiber laser array with tilt-tip and phase-locking control

We present an experimental study on tilt-tip(TT) and phase-locking(PL) control in a coherent beam combination(CBC) system of adaptive fiber laser array.The TT control is performed using the adaptive fiber-optics collimator(AFOC),and the PL control is realized by the phase modulator(PM).Cascaded and simultaneous controls of TT and PL using stochastic parallel gradient descent(SPGD) algorithm are investigated in this paper.Two-fiber-laser-,four-fiber-laser-,and six-fiber-laser-arrays are employed to study the TT and PL control.In the cascaded control system,only one high-speed CMOS camera is used to collect beam data and a computer is used as the controller.In a simultaneous control system one high-speed CMOS camera and one photonic detector(PD) are employed,and a computer and a control circuit based on field programmable gate array(FPGA) are used as the controllers.Experimental results reveal that both cascaded and simultaneous controls of TT using AFOC and PL using PM in fiber laser array are feasible and effective.Cascaded control is more effective in static control situation and simultaneous control can be applied to the dynamic control system directly.The control signals of simultaneous PL and TT disturb each other obviously and TT and PL control may compete with each other,so the control effect is limited.     

High power fiber lasers

In this review article, the development of the double cladding optical fiber for high power fiber lasers is reviewed. The main technology for high power fiber lasers, including laser diode beam shaping, fiber laser pumping techniques, and amplification systems, are discussed in detail. 1050 W CW output and 133 W pulsed output are obtained in Shanghai Institute of Optics and Fine Mechanics, China. Finally, the applications of fiber lasers in industry are also reviewed.     

High power fiber lasers

In this review article, the development of the double cladding optical fiber for high power fiber lasers is reviewed. The main technology for high power fiber lasers, including laser diode beam shaping, fiber laser pumping techniques, and amplification systems, are discussed in detail. 1050 W CW output and 133 W pulsed output are obtained in Shanghai Institute of Optics and Fine Mechanics, China. Finally, the applications of fiber lasers in industry are also reviewed.      

High-repetition-rate pulsed fiber laser based on virtually imaged phased array

High-repetition-rate(HRR) pulsed fiber lasers have attracted much attention in various fields. To effectively achieve HRR pulses in fiber lasers, dissipative four-wave-mixing mode-locking is a promising method. In this work, we demonstrated an HRR pulsed fiber laser based on a virtually imaged phased array(VIPA), serving as a comb filter. Due to the high spectral resolution and low polarization sensitivity features of VIPA, the 30 GHz pulse with high quality and high stability could be obtained. In the experiments, both the single-waveband and dual-waveband HRR pulses were achieved. Such an HRR pulsed fiber laser could have potential applications in related fields, such as optical communications.     

基于公共环形腔耦合的光纤激光器相干合成技术

 为提高光纤激光器无源自调整相干合成阵列的效率、稳定性和可扩展性,提出了基于公共光纤环形腔耦合与单模光纤滤波的光纤激光器相干合成方案。将多个2×2的光纤耦合器分别插入各单元激光器的谐振腔,利用耦合器余下的端口,两两相连构成公共环形耦合腔。采用单模光纤滤波技术,提高了各输出激光束之间相位锁定的稳定性。利用该方案在实验上实现了三路光纤激光器的被动锁相输出,实验测得的远场干涉光斑、输出功率及光谱均表明该方案适于构建性能较好的光纤激光器相干合成阵列。     

32 W百兆赫兹高重频可调谐单频激光光源

通过对连续种子光源的光强调制,并利用光纤放大器和固体介质放大器结合的混合放大方式,实现了百兆赫兹高重频可调谐单频激光光源。系统在基模输出条件下的最大输出功率为31.9 W,光束质量因子小于1.5,脉冲重复频率达到100 MHz,脉宽1 ns,测量得到的光束线宽小于0.8 GHz。实验结果验证了通过对连续光源进行光强调制获得高重频脉冲光源的可行性,并验证了混合放大方式是获得功率放大的一种有效手段。     

腔内相位调制全光纤脉冲激光器Ⅱ: 理论

针对低频腔内直接相位调制时全光纤激光器的脉冲现象,提出了合理的理论解释。基于光纤激光器自脉冲和固体激光器空间耦合的理论,对脉冲光产生的机理进行了分析,解释脉冲光产生的物理机制。假定光纤激光器中存在两个正交的偏振态,且两个偏振态以固体激光器空间耦合的模型耦合; 在相位调制作用下,两个耦合的偏振态之间相位差变化,导致两个偏振态的耦合特性发生变化,从而产生脉冲光输出。建立相应的数学模型,进行定性的理论分析。数值模拟表明,理论分析与实验结果符合得很好。     

光纤混沌相位编码保密通信系统理论研究

通过耦合激光混沌相位控制同步系统和光纤信道，提出外部光注入半导体激光器激光混沌相 位控制光纤同步以及混沌相位相移键控外调制光纤保密通信系统理论模型，数值实现了在相 位控制器控制下的远程光纤混沌同步.理论分析了光纤自相位调制对混沌信号以及对同步的 影响，导出了光纤混沌最大传输距离公式.通过连续键控调制相位控制器实现了光纤激光混 沌相位相移键控编码调制发射，设置接收系统相位控制器控制激光相位相移实现了光纤激光 混沌同步解调.数值模拟了具有比特率50Mbit/s远程光纤混沌数字编码通信系统的应用，详 细地进行了在远距离光纤传输中的系统参数失配以及系统抗噪声能力的数值分析. 关键词： 混沌 同步 光纤混沌通信 半导体激光器 相位     

基于石墨烯可饱和吸收体的纳秒锁模掺铥光纤激光器

报道了一种基于石墨烯可饱和吸收体的纳秒锁模掺铥光纤激光器.该激光器采用环形腔结构,利用自制的三层石墨烯薄膜作为可饱和吸收体实现锁模.同时在腔内插入一个窄带光纤光栅,约束腔内起振的纵模数,适当调节抽运功率和偏振控制器的角度,得到了重复频率为3.8 MHz、脉宽在3.8—94.3 ns之间灵活可调的2μm纳秒锁模脉冲输出,整个脉宽调节范围超过90 ns.此外,由于获得的兆赫兹纳秒锁模脉冲时间带宽积在49—1119范围内,即存在强烈的啁啾,因而可作为2μm波段啁啾脉冲放大系统中的种子源使用.     

窄线宽脉冲光纤激光的自相位调制预补偿研究

自相位调制(SPM)效应会展宽窄线宽脉冲光纤激光的光谱宽度,降低其相干性.通过相位调制对SPM引起的非线性相移进行预补偿,能够使脉冲激光在光纤中进行放大和传输后保持种子激光的光谱特性.基于三波耦合方程开展数值仿真,研究了在对SPM进行"欠补偿","完全补偿"和"过补偿"的情况下,SPM预补偿对受激布里渊散射阈值和激光光谱特性的影响.开展了SPM预补偿实验研究,将脉冲激光的光谱宽度从1.4 GHz压缩到120 MHz.研究内容可以为窄线宽脉冲光纤激光系统的设计搭建提供参考.     

腔内相位调制全光纤脉冲激光器Ⅰ: 实验

报道了在低频直接相位调制下,掺铒光纤激光器的脉冲现象。在光纤激光器谐振腔中插入带尾纤的LiNbO3相位调制器,利用低频周期性信号进行相位调制,能够得到重复频率为几十千赫到几百千赫左右的均匀、稳定的脉冲光输出,且发现激光光谱变化等现象。分析表明,这种脉冲现象难以用调Q、锁模等传统的脉冲光理论进行有效地解释。简要讨论了脉冲光产生的物理机制,通过对相位调制与“驰豫振荡”关系的研究,唯象地认为相位调制和“驰豫振荡”是脉冲光产生的原因。     

1.2 kW便携式光纤激光器

高功率光纤激光器通常采用如水冷散热方式进行控温,难以满足轻量化等的需求。而利用相变储能材料的特性,采用多相变控温技术,可大幅减小高功率光纤激光器系统的体积、重量。对光纤激光器的温控技术进行了分析,采用多相变温控技术,实现了波长1.08 μm、最大功率1.26 kW的全光纤激光输出,光-光效率75.4%,光束质量因子M_x2=1.21,M_y2=1.23,有效减小了激光器的体积和质量,为高功率光纤激光器的热管理提供了新方法。     

高功率光纤激光器中ASE噪声的测量方法（英）

高峰值功率脉冲光纤激光器在激光雷达系统中有着广泛的应用。然而,光纤激光器中放大自发辐射噪声（ASE）严重影响了系统的探测性能。提出一种测量高峰值功率脉冲光纤激光器中ASE噪声的方法。在该方法中,首先对高峰值功率的激光脉冲衰减,然后在时域分别测量和计算ASE噪声和激光脉冲的相对能量。给出了光纤激光器在驱动电流分别为6 A,7 A和8 A时衰减后的ASE噪声廓线以及ASE噪声占激光脉冲能量的比例。     

多单元光纤激光阵列的倾斜控制实验研究

本文结合光纤激光阵列技术的发展趋势,介绍一种基于大模场面积光纤的自适应光纤光源准直器的研制进展,搭建七单元光纤激光阵列,进行平行发射体系下阵列间的倾斜控制实验,并初步探索了基于目标在回路的共形发射体系下阵列间的倾斜控制.最后,在三级全光纤放大链路的主振荡-功率放大系统中,完成了两路10W量级光纤激光阵列的倾斜控制及锁相.为在实际大气环境下应用光纤激光阵列技术提供了参考.     

Volume Bragg grating stabilized spectrally narrow Tm fiber laser

A Tm-doped large mode area (LMA) silica fiber laser has been locked to a stable wavelength of 2,053.9 nm using a volume Bragg grating (VBG). The measured spectral width of the laser output was <300 pm, limited by the spectrometer resolution. Although this laser had modest output (approximately 5W) and slope efficiency (41%), this new approach to spectrally limiting the output of LMA fiber lasers is inherently extendable to kilowatt powers, opening up several applications including high-power pulsed fiber lasers and spectral beam combining. Performance characteristics of the laser compared to one using a dielectric mirror as a high reflector are described, and the results imply low VBG losses.