乙醇做碳源Mo-Co/MgO做催化剂合成单壁碳纳米管

本文采用柠檬酸法制备Mo-Co/MgO催化剂, 在小型流化床中, 以Ar气为载气直接携带乙醇蒸汽进入反应器, 通过化学气相沉积（CCVD）技术来合成制备单壁碳纳米管（SWCNTs）。利用扫描电镜和拉曼光谱方法研究了催化剂组分比例和载气流量等对SWCNTs制备的影响。研究结果表明: 以乙醇做碳源, Mo1-Co10/MgO做催化剂, Ar气流量为150sccm时制备的单壁碳纳米管质量最佳。     

拉曼描述碳纳米管系统:缺陷探测,产物热处理,过程分析和催化剂(英文)

利用拉曼散射技术从多角度研究了碳纳米管合成系统。发现拉曼散射技术不仅可表征碳纳米材料本身的特性,而且可分析宏观的多壁碳纳米管与单壁碳纳米管的生长过程。针对不同的碳纳米材料的生长特性提出了催化剂与反应器设计及过程控制的研究方向。同时还发展了一种基于拉曼光谱法的定量测定单壁碳纳米管含量的方法。     

电子束诱导单壁碳纳米管不稳定的新观察

利用透射电镜在室温下对不同形态的单壁碳纳米管进行了原位电子束辐照研究.研究发现:在相同的辐照条件下随着辐照时间(或辐照剂量)的增加,两端固定的单壁碳纳米管径向收缩,且收缩速率越来越快;相同直径的轴向弯曲的单壁碳纳米管比平直的单壁碳纳米管更加不稳定;一端固定另端自由的单壁碳纳米管轴向收缩,但其直径基本不变.利用单壁碳纳米管纳米曲率效应和能量束诱导非热激活效应,对上述单壁碳纳米管不稳定性现象进行了新的、合理的解释.     

V型热解火焰合成碳纳米管的催化剂选择与分析

碳纳米管是一种新型碳材料.催化剂是碳纳米管制备中的重要影响因素,而燃烧法合成碳纳米管必须使用催化剂.本文利用V型热解火焰来研究碳纳米管的合成条件,主要在理论和实验两个方面分析研究了催化剂的作用、种类、颗粒大小、失活等方面对碳纳米管生长的影响,从而为V型热解火焰法合成碳纳米管时催化剂的选取提供依据.理论分析和实验结果表明: Fe(CO)5作为一种铁剂催化剂非常适合催化CO合成碳纳米管.利用碳的"溶解-扩散-析出"机理可以用来解释Fe(CO)5催化CO合成碳纳米管的过程.     

基于HRTEM和Raman分析定向多壁碳纳米管阵列的生长机理

以二茂铁、二甲苯为前驱体,石英为衬底,在850 oC的管式炉内采用化学气相沉积法制备出了定向碳纳米管阵列. 高分辨透射电子显微镜和拉曼光谱的结果表明：碳纳米管阵列具有良好的定向性和多壁管状结构,石墨化程度高,并且只在表面存在少量单壁碳纳米管.定向多壁碳纳米管阵列的生长模式为“底部”生长模式,即在生长的初期,当催化剂颗粒较小时,析出的碳原子生成了单壁碳纳米管或与其性质类似的多壁碳纳米管(一般层数小于5层);催化剂颗粒逐渐长大后,大量的碳原子析出后生成了普通的多壁碳纳米管,从而形成了单壁碳纳米管只存在于碳纳米管阵列膜表面和多层碳纳米管膜表面与界面的现象.     

单壁碳纳米管的场发射特性研究

利用场发射显微镜(FEM)和四极质谱计分别研究了经过热处理的单壁碳纳米管的场发射图像和热处理过程中样品脱附的残气质谱.当热处理温度达到1000℃左右时得到了单壁碳纳米管的场发射像,此像可能是顶端开口的单根(16,0)锯齿形单壁碳纳米管的具有原子可分辨的场发射图像.四极质谱分析结果表明,在此温度范围W针尖晶粒间隙中有O原子和C原子释放出来.它们对单壁碳纳米管顶端的修饰是我们能观察到这些碳纳米管场发射像的可能原因. 关键词： 单壁碳纳米管(SWCNTs) 场发射显微镜(FEM) 四极质谱     

催化剂比例对单壁碳纳米管制备的影响

采用电弧放电法以Y/Ni为催化剂制备了单壁碳纳米管 ,研究了不同催化剂比例对制备产物的影响。获得了不同激发波长下 (476 5～ 1 0 6 4nm)单壁碳纳米管的拉曼光谱 ,采用图表法对径向呼吸模的谱峰进行了认定。结果表明 :样品中碳管的直径分布在 1 2～ 1 6nm之间 ,直径在 1 43nm附近的碳管居多。催化剂的比例只是影响碳管的产额 ,对其直径分布的影响很小     

单壁碳纳米管能带及其电子特性研究

从能带理论出发,采用电子紧束缚能量色散关系,推导锯齿,扶手椅和手性单壁碳纳米管(SWCNT)的电子能带结构表达式,指出单壁碳纳米管或为金属或为半导体的判据。结果表示:单壁碳纳米管的电子结构与其几何结构密切相关,如扶手椅型单壁碳纳米管是金属性的,而对其它类型的单壁碳纳米管是与碳纳米管的手性指数有关,只有手性指数n和m的差别等于3的倍数时,单壁碳纳米管是金属性的,否则会显出有带隙的半导体特性。这意味着单壁碳纳米管是由特殊的电子传输和光学性质,在纳米电子学领域具有巨大的潜在应用价值。     

乙炔/空气预混火焰法合成多壁碳纳米管的实验研究

本文利用乙炔-空气预混火焰研究了多壁碳纳米管(MWCNTs)的合成,采用涂覆有二茂铁或硝酸镍催化剂的探针在预混火焰中采样,用扫描电镜(SEM)和透射电镜(TEM)对碳纳米材料(CNTs)的形貌和结构进行了表征.结果表明在乙炔-空气预混火焰中,二茂铁和硝酸镍均能够成功合成竹节状多壁碳纳米管,严物中处发现了碳纤维(CNF)、巴基葱(bucky onion)和碳黑等物质.二茂铁催化生成的碳纳米管管径大于硝酸镍催化生成的碳纳米管的管径;在乙炔-空 气散火焰和甲烷-空气扩散火焰中硝酸镍所催化合成的碳纳米管管径相近,说明碳纳米管的管径受催化剂颗粒尺寸的影响较大.研究表明探针在火焰中停留的时间和保护气体也会影响碳纳米管的合成.     

单壁碳纳米管吸附对三联苯的研究

利用对三联苯对单壁碳纳米管进行了化学修饰,并利用透射电镜、紫外可见吸收光谱、拉曼光谱对修饰后的单壁碳纳米管进行了表征分析.通过对比吸附前后的紫外可见吸收光谱发现,吸附后的光谱强度大约下降63.1%,说明单壁碳纳米管吸附上了对三联苯.通过拉曼光谱分析发现,吸附后单壁碳纳米管的拉曼光谱中主要峰的位置向长波方向移动了6～7 cm-1,认为拉曼光谱发生移动的原因是单壁碳纳米管吸附对三联苯前后状态的改变导致的.     

Diameter-dependent thermal-oxidative stability of single-walled carbon nanotubes synthesized by a floating catalytic chemical vapor deposition method

In this paper, purified single-walled carbon naotubes (SWCNTs) with three different diameters were synthesized using a floating catalytic chemical vapor deposition method with ethanol as carbon feedstock, ferrocene as catalyst, and thiophene as growth promoter. The thermal-oxidative stability of different-diameter SWCNTs was studied by using thermal analysis (TG, DTA), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) analysis. The results indicate that small diameter SWCNTs (∼1 nm) are less stable and burn at lower temperature (610 °C), however, the larger diameter SWCNTs (∼5 nm) survive after burning at higher temperature (685 °C), the oxidation rate varies inversely with the tube diameter of SWCNTs, which may be concluded that the higher oxidation-resistant temperature of larger diameter SWCNTs can be attributed to the lower curvature-induced strain by rolling the planar graphene sheet for the larger diameter, so small tubes will become thermodynamically unstable.     

Differences in the catalyst removal from single- and double-walled carbon nanotubes

Single-walled carbon nanotubes (SWCNTs) and double-walled carbon nanotubes (DWCNTs) synthesized by a catalytic chemical vapor deposition method showed partially incorporated metal catalysts inside the graphene walls. In order to remove the metal catalysts, acid and thermal treatments were successively carried out. The methods for effective catalyst removal in SWCNTs and DWCNTs were examined by means of thermogravimetric analysis, electron microscopy, and electron paramagnetic resonance. The DWCNTs showed distinctly different metal catalyst removal behavior from that of SWCNTs due to the double-wall structure. The acid treatment is less efficient for catalyst removal from DWCNTs, while catalysts in SWCNTs are effectively removed by acid treatment. Additional thermal treatment is quite effective to remove metal catalysts from DWCNTs.     

Adsorption of nonpolar benzene derivatives on single-walled carbon nanotubes

The adsorption of benzene, toluene, and chlorobenzene on single-walled carbon nanotubes (SWCNTs) with and without acid oxidation was conducted to investigate the influences of derivative groups on benzene rings and functional groups from SWCNTs on adsorption by SWCNTs. The SWCNTs of high purity were chosen and moderate acid oxidation was performed so that the surface physical properties remained unchanged after acid oxidation and the influences of acid oxidation on adsorption were only contributed from the modification of the surface chemistry of SWCNTs. The oxygen-containing surface groups introduced by acid oxidation obstructed the interactions between functional groups of nonpolar benzene derivatives and C-rings of SWCNTs significantly. The dispersive interaction between the partially positive H⁺ of the methyl group and the oxygen-containing surface groups slightly increased the adsorption of toluene on oxidized SWCNTs at high solution pH. The thermodynamic of adsorption was also studied at different temperatures.     

直立在金膜表面的单壁碳纳米管的研究

用水溶胶体将单壁碳纳米管（ＳＷＣＮＴｓ）组装在晶态金膜表面,用扫描隧道显微镜（ＳＴＭ）研究了表面单壁碳纳米管直立于金膜表面,单根碳管的长度约在１０－１５ｎｍ之间。     

Functionalization of vertically aligned carbon nanotubes with polystyrene via surface initiated reversible addition fragmentation chain transfer polymerization

Here we demonstrate the covalent attachment of vertically aligned (VA) acid treated single-walled carbon nanotubes (SWCNTs) onto a silicon substrate via dicyclohexylcarbodiimide (DCC) coupling chemistry. Subsequently, the pendant carboxyl moieties on the sidewalls of the VA-SWCNTs were derivatized to acyl chlorides, and then finally to bis(dithioester) moieties using a magnesium chloride dithiobenzoate salt. The bis(dithioester) moieties were then successfully shown to act as a chain transfer agent (CTA) in the reversible addition fragmentation chain transfer (RAFT) polymerization of styrene in a surface initiated “grafting-from” process from the VA-SWCNT surface. Atomic force microscopy (AFM) verified vertical alignment of the SWCNTs and the maintenance thereof throughout the synthesis process. Finally, Raman scattering spectroscopy and AFM confirmed polystyrene functionalization.     

Fabrication and electrochemical properties of free-standing single-walled carbon nanotube film electrodes

An easily manipulative approach was presented to fabricate electrodes using free-standing single-walled carbon nanotube (SWCNT) films grown directly by chemical vapor deposition.Electrochemical properties of the electrodes were investigated.In comparison with the post-deposited SWCNT papers,the directly grown SWCNT film electrodes manifested enhanced electrochemical properties and sensitivity of sensors as well as excellent electrocatalytic activities.A transition from macroelectrode to nanoelectrode behaviours was observed with the increase of scan rate.The heat treatment of the SWCNT film electrodes increased the current signals of electrochemical analyser and background current,because the heat-treatment of the SWCNTs in air could create more oxide defects on the walls of the SWCNTs and make the surfaces of SWCNTs more hydrophilic.The excellent electrochemical properties of the directly grown and heat-treated free-standing SWCNT film electrodes show the potentials in biological and electrocatalytic applications.     

单壁BN纳米管和碳纳米管物理吸附储氢性能的理论对比研究

采用巨正则蒙特卡罗方法(GCMC)研究了单壁氮化硼纳米管(SWBNNTs)和单壁碳纳米管(SWCNTs)的物理吸附储氢性能,主要对比研究了纳米管的管径、温度和手性对二者物理吸附储氢量的影响. 研究结果表明：在低温下,SWBNNTs的物理吸附储氢性能优于相应的SWCNTs;但是随着温度的升高,二者的物理吸附储氢性能差别越来越小,在常温下,SWBNNTs不具备有比SWCNTs更强的物理吸附储氢性能,而是和相同条件下的SWCNTs相差不大,只是在高压下的物理吸附储氢量稍稍大于SWCNTs,并给出了合理的理论解释 关键词： 巨正则蒙特卡罗方法(GCMC) 单壁氮化硼纳米管(SWBNNTs) 单壁碳纳米管(SWCNTs) 储氢     

First principles study on magnetic and electronic properties with rare-earth atoms doped SWCNTs

The adsorptions of rare-earth (RE) atoms on (6, 0) and (8, 0) single-walled carbon nanotubes (SWCNTs) have been investigated by using the first-principles pseudopotential plane wave method within density functional theory (DFT). The binding energy, Mulliken charge, magnetic properties, band structure and DOS were calculated and analyzed. Most of RE atoms including Nd, Sm and Eu have a magnetic ground state with a significant magnetic moment. Some electrons transfer between RE-5d, 6s and C-2p orbitals. Owing to the curvature effect, the values of binding energy for RE atoms doped (6, 0) SWCNT are lower than those of the same atoms on (8, 0) SWCNT. The pictures of DOS show that hybridizations between RE-5d, 6s states and C-2p orbitals and between RE-4f and C-2p orbitals appear near the Fermi level. Results indicate that the properties of SWCNTs can be modified by the adsorptions of RE atoms.     

Growth of single wall carbon nanotubes using PECVD technique: An efficient chemiresistor gas sensor

In this work, the uniform and vertically aligned single wall carbon nanotubes (SWCNTs) have been grown on Iron (Fe) deposited Silicon (Si) substrate by plasma enhanced chemical vapor deposition (PECVD) technique at very low temperature of 550 °C. The as-grown samples of SWCNTS were characterized by field emission scanning electron microscope (FESEM), high resolution transmission electron microscope (HRTEM) and Raman spectrometer. SWCNT based chemiresistor gas sensing device was fabricated by making the proper gold contacts on the as-grown SWCNTs. The electrical conductance and sensor response of grown SWCNTs have been investigated. The fabricated SWCNT sensor was exposed to ammonia (NH₃) gas at 200 ppm in a self assembled apparatus. The sensor response was measured at room temperature which was discussed in terms of adsorption of NH₃ gas molecules on the surface of SWCNTs. The achieved results are used to develope a miniaturized gas sensor device for monitoring and control of environment pollutants.