石英音叉陀螺音叉封装问题研究

封装是石英音叉陀螺的关键工艺,封装管壳的选择、封装方式及石英音叉的固定形式对音叉的性能有直接影响。封装管壳的有限元仿真分析,可以作为封装管壳选取的依据。采用单点固定封装方式有利于石英音叉工作性能的稳定。实验中通过改变封装盖板的开合状态来改变封装方式,石英音叉的阻尼和品质因数发生了明显的改变。     

应用于扫描探针显微镜的石英音叉机械模型研究

石英音叉作为力传感器广泛地应用于各种扫描探针显微镜,主要涉及石英音叉的同相振动和反相振动两种振动模式.通过实验方法和有限元仿真方法对石英音叉的两种振动模式进行研究,发现石英音叉的双臂之间以及双臂与音叉的基部之间都存在耦合作用,双臂之间的耦合使音叉的反相共振频率升高,双臂与基部之间的耦合使音叉的同相共振频率降低.针对两种振动模式的动态特性建立了石英音叉的机械模型并进行合理简化.简化模型是一个四弹簧三质点系统,计算了简化模型的参数.通过一个音叉臂等效质量变化与音叉反相共振频率变化之间的定量关系证明了简化机械模 关键词： 扫描探针显微镜 石英音叉 振动模式 机械模型     

石英晶振用于石英增强光声光谱系统的优化实验研究

研究了音叉式石英晶振的个体尺寸、安放角度、探测部位以及外部污染对整个石英增强光声光谱系统(QEPAS)的探测灵敏度影响。测试了国内外十种不同音,结果表明顶端为楔形构造的音叉式石英晶振比规则的长方体构造的音叉拥有更高的品质因数(Q值)。在相同的测试条件下探测水的吸收线(7 306 cm-1)时获得更高的灵敏度,探测信号的强度相差高达50%。在研究音叉安放角度对探测信号影响的实验中,发现音叉的旋转角度与俯仰角度对探测信号的强度几乎没有影响,但是当光束以角度φ斜入射时,更多的噪声被带入到测量中。在正入射的情况下音叉的最佳响应位置在距离音叉底部约3.1 mm。定性研究了外部杂物污染对音叉频率的影响,发现随着污染物的附着,石英音叉的频率会呈现降低的趋势,提供了一种改变音叉式石英晶振的共振频率的方法,为石英音叉用于较低调制频率的探测提供了一种理论可能,这对于石英增强光声光谱技术用于V-T弛豫率较慢的痕量气体检测有重要的意义。     

影响近场光纤探针传输效率的若干因素

近场光学技术在高分辨率成像、光谱探测和纳米加工等领域有广泛应用,而光纤探针是其中一个关键部件.如何提高光纤探针的传输效率是近场光学技术应用中的一个重要问题.本文采用三维时域有限差分方法,计算了锥形有孔探针的传输效率,分析了锥角、针尖孔径、波长和金属层厚度等因素对光纤探针传输效率的影响,并比较了裸光纤探针和有金属涂层的光...     

钛合金和碳纤维的粘接技术

简述了某空间遥感相机中碳纤维桁架杆与钛合金接头的粘接工艺,通过对粘接剂的选择、粘接表面处理、胶层厚度等粘接强度影响的分析和破坏性力学试验表明,J133胶粘剂适用于钛合金和碳纤维材料的粘接;适当提高粘接表面的粗糙度、用化学法对粘接表面进行处理均可提高粘接强度;对该例的套接形式胶层厚度控制在0.15mm—0.2mm可保证得到好的力学性能和粘接质量。     

剪切力模式近场扫描光学显微镜的恒幅反馈控制方法研究

剪切力模式近场扫描光学显微镜(Near-field Scanning Optical Microscopy,NSOM) 的音叉探针间距控制系统中,用相位反馈控制和检测剪切力,同时采用比例＋积分（PI）技术实现对音叉探针振幅的反馈控制,使探针振幅在扫描过程中保持为恒定值.用相位信号作为探针与样品间距控制信号,分别在无振幅反馈和有振幅反馈两种情况下,以不同速率扫描得到标准CD_RW光盘光栅的两组图像,并进行了比较分析.实验表明,恒振幅反馈电路的引入有助于提高探针系统的响应速度和灵敏度,改善所得图像的质量及分辨率.     

Z箍缩动态黑腔负载装配用胶粘剂

由于Z箍缩动态黑腔负载中的低密度聚合物泡沫柱具有多孔结构和极低的力学强度,在装配过程中对胶粘剂有一定的特殊要求。实验以聚氨酯丙烯酸酯为主体树脂,丙烯酸异冰片酯为活性单体,配以光引发剂和偶联剂制得了适用于低密度泡沫粘接用的紫外光固化胶粘剂。测试表明,所研制的胶粘剂的体积收缩率仅为2.25%,且具有较高的固化速率和适当的粘接强度,能够满足稳固、快速装配的要求。通过对粘接界面的观测发现,胶粘剂在诊断孔内没有明显的扩散,且在低密度致密结构泡沫中的扩散厚度较小,均匀性好。     

新型AFM探针的制备及应用

采用熔拉 -腐蚀复合方法 ,将普通单模石英光纤制成直锥形光纤探针。利用自制工具将探针打弯 ,制成悬臂式光纤探针 ,在AFM上取得了较理想的测试结果。将自制光纤探针和商用硅材料探针获得的两种扫描图像进行了对比 ,分析了悬臂式光纤探针的特点     

光纤光栅自动化金属粘接性能

用超级电镀技术将光纤光栅应变传感元件自动粘接在金属基体上,力学模型分析表明该方法可以有效提升应变传递效率.为了检测该方法的可行性,从光纤光栅自动化粘接的主要工艺环节出发,以光纤光栅的光谱特性为研究对象,以材料力学试验为手段,对自动化金属粘接后的3个光纤光栅进行了光学特性分析和力学特性试验.结果表明:自动化金属粘接光纤光栅的成活率为100%,光纤光栅粘接后的应变测量灵敏度保持在1.2 pm/με,应变传递效率在0.98以上,线性度达0.99,光纤光栅在加卸中的一致性偏差仅为10~(-6)、漂移仅为0.05,优于传统手工粘接.     

金属覆层光纤探针近场特性研究

采用有限积分法对用于近场光学显微镜的旋转对称光纤探针进行了数值模拟计算,研究了光纤探针开口附近亚波长范围的电磁场及其能量密度的分布.计算结果表明,在探针外,光场为沿探针轴线方向的近逝波,其空间光场的分布与激励光场及其极化方向有关,在激励光场的极化方向出现了由感应电荷引起的边缘增强效应.同时研究了近场光纤探针的空间分辨率和样品处的电磁场能量,结果表明光纤探针孔的尺寸及其与样品的作用距离是影响探针的分辨率和样品内电磁场能量的重要因素.     

Resolution enhancement in a reflection mode near-field optical microscope by second-harmonic modulation signals

The motion of the probe tip in a near-field scanning optical microscope, dithered by vibration of a tuning fork, can modulate the reflection signal from the sample surface not only at the fundamental dithering frequency but also at its second harmonic. By lock-in amplification of these modulated signals, enhanced optical images are obtained, even with an uncoated fiber probe. In particular, accurate optical images with higher resolution are obtained when the second-harmonic signal is detected, which results from the parametric modulation of the tip-sample separation at the double frequency of the horizontal dithering motion of the tip. Using a DVD ROM with a track pitch of 0.74 mum as a test sample, we observed that the sharp edges around the pits are clearly resolved with the second-harmonic signals and obtained enhanced resolution of ~70 nm full width at half-maximum.     

Shear-Force Detection by Reusable Quartz Tuning Fork without External Vibration

Many studies have reported on the use of quartz tuning forks (a type of crystal oscillator used in wristwatches) in the detection of shear force, employed to control the distance between the probe and the sample in a scanning near-field optical microscope. This study focuses on a newly-devised shear force detection method capable of simultaneous non-external oscillation and detection, which also allows for subsequent reuse of a tuning fork. The optimum configuration and tip length for inserting a probe into the slit of a tuning fork have been elucidated. The shear force was detectable in about 5 nm decay length using such conditions.     

Theoretical analysis of a quartz-enhanced photoacoustic spectroscopy sensor

Quartz-enhanced photoacoustic spectroscopy (QEPAS) sensors are based on a recent approach to photoacoustic detection which employs a quartz tuning fork as an acoustic transducer. These sensors enable detection of trace gases for air quality monitoring, industrial process control, and medical diagnostics. To detect a trace gas, modulated laser radiation is directed between the tines of a tuning fork. The optical energy absorbed by the gas results in a periodic thermal expansion which gives rise to a weak acoustic pressure wave. This pressure wave excites a resonant vibration of the tuning fork thereby generating an electrical signal via the piezoelectric effect. This paper describes a theoretical model of a QEPAS sensor. By deriving analytical solutions for the partial differential equations in the model, we obtain a formula for the piezoelectric current in terms of the optical, mechanical, and electrical parameters of the system. We use the model to calculate the optimal position of the laser beam with respect to the tuning fork and the phase of the piezoelectric current. We also show that a QEPAS transducer with a particular 32.8 kHz tuning fork is 2–3 times as sensitive as one with a 4.25 kHz tuning fork. These simulation results closely match experimental data.     

陀螺惯性制导及其军事应用

简要介绍机械惯性陀螺、环形激光陀螺、光纤陀螺、半球谐振陀螺、石英音叉陀螺的基本工作原理及其军事应用,并预测了陀螺惯性制导的发展趋势。     

Application of a self-sensing conductive probe for Si device imaging

For the evaluation of two-dimensional carrier profiles in semiconductor devices, we have developed a novel form of probe–sensor combined unit that uses an etched tungsten wire as a conductive probe, and commercially available quartz tuning fork as the force sensor. This unit has a self-sensing capability due to the piezoelectric effect of quartz tuning fork, thus obviating optical setup, and its conductivity is higher and more stable than that of conventional metal-coated Si cantilever. In addition, this probe–sensor combined unit is inexpensive and easy to use, when compared to the well-known optical methods of Si-based cantilever vibration detection system. Our scanning probe microscope using this probe–sensor combined unit is able to mapping the capacitive gradient signal (dC/dZ image) and internal damping of quartz tuning fork oscillation (dissipation image) while scanning the sample surface. In this letter, we show the results of visualization of the p–n junction locus of a Si metal–oxide–semiconductor field effect transistor in both dC/dZ and dissipation images.     

Evanescent-wave photoacoustic spectroscopy with optical micro/nano fibers

We demonstrate gas detection based on evanescent-wave photoacoustic (PA) spectroscopy with tapered optical fibers. Evanescent-field instead of open-path absorption is exploited for PA generation, and a quartz tuning fork is used for PA detection. A tapered optical fiber with a diameter down to the wavelength scale demonstrates detection sensitivity similar to an open-path system but with the advantages of easier optical alignment, smaller insertion loss, and multiplexing capability.     

基于泛频振动的石英增强光声光谱测声器优化设计

为了进一步提高基于泛频振动的石英增强光声光谱测声器探测灵敏度,在一次泛频振动模式下采用一个比商用标准音叉外形尺寸大5倍的定制大音叉,并对其性能进行优化.通过理论和实验研究得出了音叉与激光的最佳作用位置,发现音叉的一次泛频振动有两个波腹点,且在距离音叉根部8 mm处,音叉振臂的振动幅度最大.微型声音谐振腔由三种不同内径的不锈钢毛细管加工而成,与音叉组成共轴配置石英增强光声光谱光谱测声器,用来进一步增强信号幅值.在最佳微型声音谐振腔配置下,获得了30倍的信号增益因子,有效提高了石英增强光声光谱光谱测声器的探测灵敏度.     

Electroless nickel plating on optical fiber probe

As a component of near-field scanning optical microscope （NSOM）, optical fiber probe is an important factor influncing the equipment resolution. Electroless nickel plating is introduced to metallize the optical fiber probe. The optical fibers are etched by 40% HF with Turner etching method. Through pretreatment, the optical fiber probe is coated with Ni-P film by electroless plating in a constant temperature water tank. Atomic absorption spectrometry （AAS）, scanning electron microscopy （SEM）, and energy dispersive X-ray spectrometry （EDXS） are carried out to characterize the deposition on fiber probe. We have reproducibly fabricated two kinds of fiber probes with a Ni-P film： aperture probe and apertureless probe. In addition, reductive particle transportation on the surface of fiber probe is proposed to explain the cause of these probes.