Radiation impedance of a finite circular piston on a viscoelastic half-space with application to medical diagnosis

In a recent study a new analytical solution was developed and validated experimentally for the problem of surface wave generation on a linear viscoelastic half-space by a rigid circular disk located on the surface and oscillating normal to it. The results of that study suggested that, for the low audible frequency range, some previously reported values of shear viscosity for soft biological tissues may be inaccurate. Those values were determined by matching radiation impedance measurements with theoretical calculations reported previously. In the current study, the sensitivity to shear viscoelastic material constants of theoretical solutions for radiation impedance and surface wave motion are compared. Theoretical solutions are also compared to experimental measurements and numerical results from finite-element analysis. It is found that, while prior theoretical solutions for radiation impedance are accurate, use of such measurements to estimate shear viscoelastic constants is not as precise as the use of surface wave measurements.     

Propagation of laser array beams in a turbulent atmosphere

The propagation of phase-locked and non-phase-locked laser array beams of radial and rectangular symmetries in a turbulent atmosphere are investigated based on the extended Huygens–Fresnel integral. The beamlet used in our paper for constructing the laser array beams is of elliptical Gaussian mode. Analytical formulae for the average irradiance of phase-locked and non-phase-locked radial and rectangular laser array beams are derived through vector integration and tensor operation. The irradiance properties of these laser array beams in a turbulent atmosphere are studied numerically. It is found that both phase-locked and non-phase-locked radial and rectangular laser array beams eventually become circular Gaussian beams in a turbulent atmosphere, which is much different from their propagation properties in free space. The propagation properties are closely related to the parameters of laser array beams and the structure constant of the turbulent atmosphere. PACS 42.25.Bs; 41.85.Ew; 42.68.Ay     

Higher order mode acoustic transmission through the walls of rectangular ducts

As an extension of previous work on low frequency fundamental mode acoustic transmission through the walls of rectangular ducts, results are presented here on the transmission of internally propagated higher order acoustic modes through the duct walls. Subject to various assumptions, it is possible to obtain a closed form solution to the structural wave equation governing the motion of the duct's walls, and this is used to predict the response of the walls to the internal pressure field. The resultant acoustic radiation is estimated here by assuming that the duct radiates like a circular cylinder with the same surface velocity distribution. Both experimental and theoretical results are given and agreement between the two is tolerably good.     

Propagation properties of anomalous hollow beams in a turbulent atmosphere

Propagation of circular and elliptical anomalous hollow beams in a turbulent atmosphere is investigated in detail. Based on the extended Huygens–Fresnel integral, analytical formulae for the average irradiance of circular and elliptical anomalous hollow beams propagating in a turbulent atmosphere are derived. The irradiance and spreading properties of circular and elliptical anomalous hollow beams in a turbulent atmosphere and in free space are studied numerically. It is found that circular and elliptical anomalous hollow beams at short propagation distance in turbulent atmosphere have similar propagation properties to those of free space, while at long propagation distance, circular and elliptical anomalous hollow beams eventually become circular Gaussian beams in a turbulent atmosphere, which is much different from their propagation properties in free space. The conversion from an anomalous hollow beam to a circular Gaussian beam becomes quicker and the beam spot spreads more rapidly for a larger structure constant, a shorter wavelength and a smaller waist size of the initial beam.     

Simplified method for solving problems of vibrating plates of doubly connected arbitrary shape,part II: Applications and experiments

The eigenfrequencies of ring-shaped polygonal plates, ring-shaped elliptical plates, rectangular plates with elliptical inner boundaries and circular plates with elliptical inner boundaries are obtained. The method developed by the author in the companion paper (Part I) is applied for finding the eigenfrequencies. To verify the present results, experimental tests have also been carried out for some important cases.     

Fractional Fourier transform for off-axis dark-hollow beams

Based on the definition of fractional Fourier transform (FRT) in the rectangular coordinate system, the FRT for off-axis circular and elliptical dark-hollow beams (DHB) is studied in detail, and analytical formulae are derived for the FRT for off-axis circular and elliptical DHB. The properties of off-axis DHB in the FRT plane are illustrated numerically by use of the derived formulae. The results show that the properties of the off-axis DHB in the FRT plane are closely related with the parameters of the beam and fractional order. The derived formula provides a convenient way for analyzing and calculating the FRT of off-axis DHBs.     

Acoustic elliptical cylindrical cloaks

By making a comparison between the acoustic equations and the 2-dimensional (2D) Maxwell equations, we obtain the material parameter equations (MPE) for acoustic elliptical cylindrical cloaks. Both the theoretical results and the numerical results indicate that an elliptical cylindrical cloak can realize perfect acoustic invisibility when the spatial distributions of mass density and bulk modulus are exactly configured according to the proposed equations. The present work is the meaningful exploration of designing acoustic cloaks that are neither sphere nor circular cylinder in shape, and opens up possibilities for making complex and multiplex acoustic cloaks with simple models such as spheres, circular or elliptic cylinders.     

Some extensions of the Gaussian beam expansion: radiation fields of the rectangular and the elliptical transducer

A straightforward extension of Gaussian beam expansion is presented for calculation of the Fresnel field integral [J. J. Wen and M. A. Breazeale, J. Acoust. Soc. Am. 83, 1752-1756 (1988)]. The source distribution function is expanded into the superposition of a series of two-dimensional Gaussian functions. The corresponding radiation field is expressed as the superposition of these two-dimensional Gaussian beams and is then reduced to the computation of these simple functions. This treatment overcomes the limit that the shape of source is of circular axial-symmetry. The numerical examples are presented for the field of the (uniform) elliptical and the rectangular piston transducers and agree well with the results given by complicated computation.     

Finite amplitude pressure field of elliptical and rhomboid transducers in three dimensions

Design of different type of transducers to enhance image quality by forming narrow beams at the principals of nonlinear acoustics is considered in the paper. Thus, the nonlinear pressure fields of elliptical and rhomboid transducers were simulated in three dimensions. The simulation method presented in this study is based on Aanonsen’s model for circular sources, and closely follows the model that recently explored for the nonlinear wave propagation due to square and rectangular sources in three dimensions [Kaya et al. “Pressure field of rectangular transducers at finite amplitude in three dimensions,” Ultrasound in Med. Biol., vol. 32, no. 2, pp. 271–280, 2006]. It is assumed that elliptical and rhomboid sources are plane sources, and driven at 2.25 MHz fundamental frequency. Typical results of nonlinear acoustical pressure field simulation are presented there in three dimensions for elliptical and rhomboid sources and compared with the results for rectangular source. The similarities and differences between the nonlinear pressure field of rectangular, elliptical and rhomboid sources are discussed. The numerical results show that diffraction effects and acoustical beam cross section depend on the source geometry a lot. It is noticeable that the nonlinear pressure field of a rectangular source has a broader beam profile than elliptical and rhomboid source.     

Extension of the mode method for viscoelastic media and focused ultrasonic beams

In the present study viscoelasticity is introduced in the mode model and the orthogonality condition is adapted for viscous media. The expansion of convergent acoustic Gaussian beams in terms of radiation modes for viscoelastic media is studied as well. The effects on the reflected and transmitted profiles of acoustic beams incident from an ideal liquid onto a viscoelastic plate are shown and physically explained. It is shown that focusing the incident beam can suppress divergence effects and gives the possibility to measure shear wave attenuation coefficients.     

On Diffraction of a Sawtooth Nonlinear Wave by a Narrow Circular Aperture in a Screen

Acoustical Physics - The paper presents the experimental and theoretical studies of diffraction effects in intense acoustic beams diffracted by a narrow circular aperture in a screen. The...     

Gauss声束对离轴椭圆柱的声辐射力矩

利用部分波展开法求解得到了Gauss声束入射下刚性和非刚性椭圆柱的声散射系数,推导了一般情况下的声辐射力矩表达式.在此基础上,通过一系列数值仿真详细分析了离轴距离、入射角度和束腰半径对声辐射力矩的影响.结果表明:正向与负向声辐射力矩均可以在一定条件下存在;低频情况下刚性椭圆柱比非刚性椭圆柱更容易产生较强的声辐射力矩;特定频率的入射声场可以激发出非刚性椭圆柱不同阶的共振散射模式,因而非刚性椭圆柱的声辐射力矩峰值与频率的关系更密切;增加束腰半径有利于扩大散射截面,进而增加椭圆柱的声辐射力矩.该研究结果预期可以为利用声辐射力矩实现粒子的可控旋转和流体黏度的反演提供一定的理论指导.     

Generation of ultrasonic waves in water by an elliptical Gaussian laser beam

The paper presents an analysis of ultrasonic wave generation in water by intensity modulated elliptical Gaussian laser beams. It is found that generated acoustic radiation is highly directional both in polar and azimuthal directions. An increase in the assymmetry of the transverse intensity distribution from the Gaussian dependence enhances the source directivity considerably. An obvious conclusion is that elliptical Gaussian beams are better choice in applications where it is desired to communicate in an approximately prescribed small solid angle.     

Generalized response of a sphere embedded in a viscoelastic medium excited by an ultrasonic radiation force

The response of an embedded sphere in a viscoelastic medium excited by acoustic radiation force has been studied in both the time- and frequency-domains. This model is important because it can be used to characterize the viscoelastic properties of the medium by fitting the response to the theoretical model. The Kelvin-Voigt model has been used exclusively in these models. An extension to the previously reported models is described so that any viscoelastic rheological model can be used. This theoretical development describes the generalized embedded sphere response both in the time and frequency domains. Comparing the results from derivations in both domains showed very good agreement with a median absolute error (MAE) ranging from 0.0044 to 0.0072. Good agreement is demonstrated with finite element model simulations and the theory with a MAE of 0.006. Lastly, results for characterization of gelatin and rubber materials with the new theory are shown where the MAE values were used to determine which rheological model best describes the measured responses.     

Bessel驻波对椭球形液滴的声辐射转矩

在实际的声操控中,由于声辐射力、表面张力和重力的共同作用,液滴往往呈现出椭球的形状,在螺旋声场中会受到力矩的作用而发生转动。从声波的散射理论出发,根据部分波展开法求解得到了椭球形液滴在Bessel驻波场中的声散射系数,并给出了其受到的声辐射转矩的解析式。在此基础上,对椭球形不可压缩液滴和椭球形可压缩液滴分别进行数值计算。仿真结果表明,不可压缩液滴的声辐射转矩与声束半锥角的关系更密切,而可压缩液滴则更依赖于特定的频率;提升Bessel驻波场的阶数有利于增强声辐射转矩的峰值,但在中低频处较难对可压缩液滴产生明显的力矩。该研究结果预期对利用螺旋声场进行液滴的操控具有理论指导作用。      

The acoustic modes of a two-dimensional rectangular cavity

A theoretical study of the acoustic modes of a two-dimensional rectangular cavity is presented in this paper. It is found that for cavities with length to depth ratio of unity or larger the natural modes are heavily damped due to acoustic radiation. Numerical results for lower order modes are given. The physical significance of strong radiation damping on the onset of cavity tones induced by outside flow at low Mach number is discussed.     

Theoretical Analysis of Shear Wave Interference Patterns by Means of Dynamic Acoustic Radiation Forces

Acoustic radiation forces associated with high intensity focused ultrasound stimulate shear wave propagation allowing shear wave speed and shear viscosity estimation of tissue structures. As wave speeds are meters per second, real time displacement tracking over an extend field-of-view using ultrasound is problematic due to very high frame rate requirements. However, two spatially separated dynamic external sources can stimulate shear wave motion leading to shear wave interference patterns. Advantages are shear waves can be imaged at lower frame rates and local interference pattern spatial properties reflect tissue's viscoelastic properties. Here a theoretical analysis of shear wave interference patterns by means of dynamic acoustic radiation forces is detailed. Using a viscoelastic Green's function analysis, tissue motion due to a pair of focused ultrasound beams and associated radiation forces are presented. Overall, this paper theoretically demonstrates shear wave interference patterns can be stimulated using dynamic acoustic radiation forces and tracked using conventional ultrasound imaging.     

Estimation of mechanical properties of a viscoelastic medium using a laser-induced microbubble interrogated by an acoustic radiation force

An approach to assess the mechanical properties of a viscoelastic medium using laser-induced microbubbles is presented. To measure mechanical properties of the medium, dynamics of a laser-induced cavitation microbubble in viscoelastic medium under acoustic radiation force was investigated. An objective lens with a 1.13 numerical aperture and an 8.0 mm working distance was designed to focus a 532 nm wavelength nanosecond pulsed laser beam and to create a microbubble at the desired location. A 3.5 MHz ultrasound transducer was used to generate acoustic radiation force to excite a laser-induced microbubble. Motion of the microbubble was tracked using a 25 MHz imaging transducer. Agreement between a theoretical model of bubble motion in a viscoelastic medium and experimental measurements was demonstrated. Young's modulii reconstructed using the laser-induced microbubble approach were compared with those measured using a direct uniaxial method over the range from 0.8 to 13 kPa. The results indicate good agreement between methods. Thus, the proposed approach can be used to assess the mechanical properties of a viscoelastic medium.     

Anisotropy of sound velocity for a new PbB4O7 crystal as determined by the laser ultrasonic technique

4 O₇ crystal is a new nonlinear optical crystal. For the first time the anisotropy of the velocities of its longitudinal and surface acoustic waves (SAWs) are determined by laser ultrasonic technique. The velocities of surface waves for X-, Y-, and Z-cut crystals are also calculated. The theoretical calculations of slowness curves are in good agreement with experimental results. The SAW slowness curve is elliptical for Y- or Z-cut crystal wafers, and circular for an X-cut wafer. Received: 27 January 1997/Accepted: 30 July 1997     

Motion of a solid sphere in a viscoelastic medium in response to applied acoustic radiation force: Theoretical analysis and experimental verification

The motion of a rigid sphere in a viscoelastic medium in response to an acoustic radiation force of short duration was investigated. Theoretical and numerical studies were carried out first. To verify the developed model, experiments were performed using rigid spheres of various diameters and densities embedded into tissue-like, gel-based phantoms of varying mechanical properties. A 1.5 MHz, single-element, focused transducer was used to apply the desired radiation force. Another single-element, focused transducer operating at 25 MHz was used to track the displacements of the sphere. The results of this study demonstrate good agreement between theoretical predictions and experimental measurements. The developed theoretical model accurately describes the displacement of the solid spheres in a viscoelastic medium in response to the acoustic radiation force.