Ex situ synthesis and optical properties of ZnO-PbS nanocomposites

Zinc oxide (ZnO) and lead sulphide (PbS) nanoparticles separately synthesized by a precipitation method were combined by an ex situ route to prepare ZnO-PbS nanocomposites with different molar ratios of ZnO and PbS. The structure and morphology of the ZnO, PbS and ZnO-PbS samples were analyzed with X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). A UV-vis spectrophotometer was used to collect the absorption and 325 nm He-Cd and 488 nm Ar lasers were used to collect the photoluminescence data from the samples. ZnO nanoparticles showed a broad and stable emission peak at ∼570 nm, while a strongly quantum confined emission from PbS nanoparticles was detected at ∼1344-1486 nm. The ZnO-PbS nanocomposites exhibited dual emission in the visible and near-infrared (NIR) regions that is associated with defects and recombination of excitonic centres in the ZnO and PbS nanoparticles, respectively. The PL intensity of the visible emission from the ZnO-PbS nanocomposite was shown to increase when the ZnO to PbS molar ratio was 5:1 and the emission was almost quenched at molar ratios of 1:1 and 1:5. For different molar ratios of ZnO to PbS, the PL intensity of the NIR emission from the ZnO-PbS nanocomposites was more intense than that of PbS nanoparticles.     

Surface modification of ZnO nanocrystals

Nano-crystalline ZnO particles were synthesized using alcoholic solutions of zinc acetate dihydrate through a colloidal process. Five types of capping agents: 3-aminopropyl trimethoxysilane (Am), tetraethyl orthosilicate (TEOS), mercaptosuccinic acid (Ms), 3-mercaptopropyl trimethoxysilane (Mp) and polyvinylpyrrolidone (Pv) were added at the first ZnO precipitation time (first PPT) to limit the particle growth. The first three capping agents effectively capped the ZnO nanoparticles and limited the growth of the particles, while the last two capping agents caused agglomeration or larger clusters in the solutions. Particles synthesized were in the size range of 10-30 nm after capping, and grew to 60 and 100 nm in 3 and 6 weeks, respectively, during storage at ambient conditions. Refluxing time was found to only affect the first PPT time. Washing by ethanol and slow drying were very important in converting Zn(OH)₂ into ZnO. XRD analyses revealed single phase ZnO Wurtzite crystal structure. Photoluminescence (PL) spectra showed high-intensity in UV emission and very low intensity in the visible emission, which indicates a good surface morphology of the ZnO nanoparticles with little surface defects. Optical absorption spectra showed a blue shift by the capped ZnO due to the quantum confinement effect by the single crystal size of 5-6 nm as analysed by TEM. Capping effectiveness of each agent is discussed through possible capping mechanism and chemical reaction of each capping agent. This synthesis process is a low cost, high purity, easy to control method using only bio-compatible materials.     

Room-temperature deposition of crystalline patterned ZnO films by confined dewetting lithography

In this work patterned ZnO films were prepared at room-temperature by deposition of ∼5 nm size ZnO nanoparticles using confined dewetting lithography, a process which induces their assembly, by drying a drop of ZnO colloidal dispersion between a floating template and the substrate. Crystalline ZnO nanoparticles exhibit a strong visible (525 nm) light emission upon UV excitation (λ = 350 nm). The resulting films were characterized by scanning electron microscopy (SEM) and atomic force microscope (AFM). The method described herein presents a simple and low cost method to prepare crystalline ZnO films with geometric patterns without additional annealing. Such transparent conducting films are attractive for applications like light emitting diodes (LEDs). As the process is carried out at room temperature, the patterned crystalline ZnO films can even be deposited on flexible substrates.     

Photoluminescence study on amino functionalized dysprosium oxide–zinc oxide composite bifunctional nanoparticles

An organic dispersion of 9–15 nm size stable dysprosium oxide incorporated zinc oxide nanocomposites exhibiting luminescence in the visible region has been synthesised by a wet chemical precipitation technique at room temperature. Tetraethoxysilane TEOS [(C₂H₅O)₄Si], (3-aminopropyl) trimethoxysilane (APTS) and a 1:1 mixture of TEOS–APTS have been used as capping agents to control the particle size as well as to achieve uniform dispersion of composite nanoparticles in methanol medium. X-ray diffractometer (XRD) analysis reveals the formation phase of amino-functionalised colloidal dysprosium oxide incorporated ZnO composite nanoparticles to be of zincite structure. The Transmission Electron Microscopy (TEM) images show that the particles are spheroids in shape, having average crystalline sizes ranging from 9 to 15 nm. The photoluminescence (PL) observed in these composites has been attributed to the presence of near band edge excitonic emission and existence of defect centres. The time correlated single photon counting studies of the composite nanoparticles exhibited three decay pathways. The enhanced PL emission intensity of solid state fluorescence spectra of samples is attributed to the absence of vibrational relaxation process.     

A simple synthesis and magnetic behavior of nanocrystalline Zn0.9Co0.1O powders by using Zn and Co acetates and polyvinyl pyrrolidone as precursors

This paper reports the synthesis of nanocrystalline powders of Co-doped ZnO (i.e. Zn_0.9Co_0.1O (ZCO)) diluted magnetic semiconductor by a simple method using acetate salts of Zn and Co, and polyvinyl pyrrolidone as precursors. The morphology and crystalline size of the synthesized powders were evaluated by scanning electron microscopy and transmission electron microscopy (TEM). The ZCO powders consist of both nanoparticles with particle sizes of ∼50–100 nm and nanorods with diameters of ∼100–200 and ∼200–500 nm in length. The X-ray diffraction and TEM results indicated that the synthesized ZCO powders had the pure wurtzite structure without any significant change in the structure affected by Co substitution. Optical absorption measurements showed absorption bands indicating the presence of Co ions in substitution of Zn ions. Room-temperature magnetization results revealed a paramagnetic behavior for the ZCO precursor (as grown sample) and a ferromagnetic behavior for the ZCO powders calcined in air at 873 K for 1 h.     

Structural and optical properties of poly-vinylpyrrolidone modified ZnO nanorods synthesized through simple hydrothermal process

The synthesis of nanocrystalline zinc oxide (ZnO) in the presence of poly-vinylpyrrolidone (PVP) as capping agent through hydrothermal process, and their structural and optical properties were reported. PVP modified ZnO nanorods grown hydrothermally involve a heterogeneous chemical reaction in the presence of water as a solvent medium and reaction temperature of 100 °C for 7 h in a hot air oven and calcined in air at 500 °C for 3 h. Crystal structure, phase purity and average crystallite size of ZnO were studied by powder X-ray diffraction (PXRD). The strain associated with the as-prepared samples due to lattice deformation was estimated by Williamson–Hall (W–H) analysis. Structural morphology was investigated using scanning electron microscopy (SEM), which showed the formation of nanorods with PVP capping. The growth mechanism of ZnO nanorods and its capping by poly-vinylpyrrolidone are briefly discussed through FT-IR adsorption spectra. The optical behavior of the samples was analyzed through photoluminescence (PL) spectroscopy with an emission spectra in visible region ∼418 nm indicate the applicability of using it as a transport material in solar cells.     

Enhancement of optical properties and donor-related emissions in Y-doped ZnO

The Zn_1−xY_xO nanoparticles with good optical properties have been prepared by sol–gel method. The yttrium doping effect on the structures and optical properties were investigated by XRD, SEM, XPS and low temperature photoluminescence. The UV emission intensity of yttrium doped ZnO was over 300 times stronger than that of pure ZnO, which was an exciting result in enhancing the ultraviolet near band edge emission in photoluminescence from ZnO nanoparticles. The UV emission band of doped ZnO nanoparticles exhibits a red shift from 388 to 398 nm, indicating a shallow energy level near valence band has been formed due to the yttrium doping into ZnO lattices. The defect-related band is suppressed (I_D/I_UV = 1–0.83) considerably in Zn_1−xY_xO nanoparticles, revealing the quenching of the broad yellow-orange emission. The doping effect on the optical properties is investigated by temperature dependent photoluminescence. The experimental results indicated that the donor level of yttrium is deeper than that of undoped ZnO.     

Formation of ZnO@Cd(OH)2 core-shell nanoparticles by sol-gel method: An approach to modify surface chemistry for stable and enhanced green emission

We report the formation of highly stable and luminescent ZnO@Cd(OH)₂ core-shell nanoparticles by simple introduction of cadmium salt in the initial precursor solution, used to synthesize ZnO nanoparticles by sol-gel route. The cadmium to zinc salt concentration ratio has been also varied to control the growth of ZnO nanoparticles at the smaller particle size. Formation of ZnO@Cd(OH)₂ core-shell nanostructure has been confirmed by X-ray diffraction (XRD), energy dispersive analysis of X-rays (EDAX) and X-ray photoelectron spectroscopy (XPS). UV-vis absorption spectroscopy exhibits blue-shift in absorption edge on increasing cadmium concentrations. The photoluminescence emission spectra showed the remarkably stable and enhanced visible (green) emission from suspended ZnO@Cd(OH)₂ nanoparticles in comparison to bare ZnO nanoparticles. It is postulated that Cd(OH)₂ layer at the surface of ZnO nanoparticles prevents the agglomeration of nanoparticles and efficiently assists the trapping of hole at the surface site, a first step necessary for visible emission. The Fourier transform infrared spectroscopy (FTIR) also supports our assumption about surface chemistry.     

Green photoluminescence from highly oriented ZnO thin film for photovoltaic application

We report here the fabrication of ZnO nanoparticles embedded on glass substrate by sol–gel and spin coating technique. Transmission electron microscope images revealed that the thin film is composed of ZnO nanoparticles. X-ray diffraction data confirms that the fabricated ZnO nanoparticles have hexagonal unit cell structure. The ZnO nanocrystals of the thin film are oriented along the c-axis of the hexagonal unit cell. UV–vis absorption spectroscopy shows that the absorption occurring at 373 nm in the ZnO thin film. The band gap was calculated from the absorption data and found to be 3.76 eV. This band gap enhancement occurs due to size effect in the nanoscale regime. Room temperature photoluminescence spectrum shows strong green emission at 530 nm owing to the singly ionized oxygen vacancy. This green emission was further investigated by annealing the thin film at different temperature. This singular green emission will be very useful in optoelectronic and nanophotonic devices.     

Synthesis by sol–gel process,structural and optical properties of nanoparticles of zinc oxide doped vanadium

We report the elaboration of vanadium-doped ZnO nanoparticles prepared by a sol–gel processing technique. In our approach, the water for hydrolysis was slowly released by esterification reaction followed by a supercritical drying in ethyl alcohol. Vanadium doping concentration of 10 at.% has been investigated. After treatment in air at different temperatures, the obtained nanopowder was characterised by various techniques such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and photoluminescence (PL). Analysis by scanning electron microscopy at high resolution shows that the grain size increases with increasing temperature. Thus, in the case of thermal treatment at 500 °C in air, the powder with an average particle size of 25 nm shows a strong luminescence band in the visible range. The intensity and energy position of the obtained PL band depends on the temperature measurement increase. The mechanism of this emission band is discussed.     

Preparation and characterization of nanocrystalline ZnO particles from a hydrothermal process

Rod-like ZnO nanoparticles were prepared by the hydrolysis of zinc acetate under heating in diethylene glycol (DEG). Structural characterization of the synthesized powders was investigated by XRD, FT-IR, electron paramagnetic resonance (EPR) and transmission electron microscopy (TEM). The size of the particles increased as the amount of H₂O added increased in the nano size range. The average crystallite size calculated from the XRD patterns varied from 6 to 64 nm corresponding to the amount of H₂O added. The ZnO nanopartilces possess the wurtzite type crystallographic structure. It was found that these ZnO nanoparticles had singly ionized oxygen vacancy defect () and superoxide ions from the EPR investigations. A strong near UV emission of the ZnO nanoparticles at about 380 nm was observed and its intensity decreased as the amount of H₂O increased. This emission of ZnO nanoparticles is found to be particles size dependent due to the confinement effect. A green emission at about 540 nm due to the recombination of electrons trapped at singly ionized oxygen vacancies defect () appeared when the amount of H₂O increased. The intensity of the green emission increases as the concentration of increases.     

Characterization and optical property of ZnO nano-, submicro- and microrods synthesized by hydrothermal method on a large-scale

In the present paper, well-dispersed ZnO nano-, submicro- and microrods with hexagonal structure were synthesized by a simple low temperature hydrothermal process from zinc nitrate hexahydrate without using any additional surfactant, organic solvent or catalytic agent. The phase and structural analysis were carried out by X-ray diffraction (XRD), the morphological analysis was carried out by field emission scanning electron microscopy (FESEM) and the optical property was characterized by room-temperature photoluminescence (PL) spectroscopy. The results revealed the high crystal quality of ZnO powder with hexagonal (wurtzite-type) crystal structure and the formation of well-dispersed ZnO nano-, submicro- and microrods with diameters of about 50, 200 and 500 nm, and lengths of 300 nm, 1 μm and 2 μm, respectively, on a large-scale just using the different temperatures. Room-temperature PL spectrum from the ZnO nanorods reveals a strong UV emission peak at about 360 nm and no green emission band at ∼530 nm. The strong UV photoluminescence indicates the good crystallization quality of the ZnO nanorods. Room-temperature PL spectra from the ZnO submicro- and microrods reveal a weak UV emission peak at ∼400 nm and a very strong visible green emission at 530 nm, that is ascribed to the transition between V_oZn_i and valence band.     

Optical characterization of ZnO nanoparticles capped with various surfactants

The presence of surfactants (Hexamine, tetraethylammonium bromide (TEAB), cetyltrimethylammonium bromide (CTAB), tetraoctylammonium bromide (TOAB) and PVP) on the surface of zinc oxide (ZnO) nanoparticles resulted variation in their optical properties. The optical properties of each surfactant-capped zinc oxide nanoparticles were investigated using UV-visible absorption and fluorescence techniques. The particle size of these nanoparticles were calculated from their absorption edge, and found to be in the quantum confinement range. The absorption spectra and fluorescent emission spectra showed a significant blue shift compared to that of the bulk zinc oxide. Large reduction in the intensity of visible emission of zinc oxide/surfactant was observed and these emissions were vanished more quickly, with the decrease in excitation energy, for the smaller nanoparticles. Out of the four surfactants (other than PVP), CTAB-capped zinc oxide has smallest particle size of 2.4 nm, as calculated from the absorption spectrum. Thus the presence of surfactant on the surface of zinc oxide plays a significant role in reducing defect emissions. Furthermore, ZnO/PVP nanoparticles showed no separate UV emission peak; however, the excitonic UV emission and the visible emission at 420 nm overlap to form a single broad band around 420 nm.     

The influence of annealing temperature on the structure,morphologies and optical properties of ZnO nanoparticles

ZnO nanoparticles (NPs) have been successfully synthesized by the simple solution method at low temperature. The effects of annealing temperature on the structure and optical properties of ZnO NPs were investigated in detail by X-ray diffraction, transmission electron microscopy (TEM), ultraviolet–visible (UV–vis) spectroscopy and photoluminescence (PL) measurements. As the annealing temperature was increased above 180 ^°C the particles morphology evolved from spherical to hexagonal shape, indicating that the average particle size increased from 11 nm to 87 nm. The UV-vis and PL spectra showed a red-shift from 3.62 to 3.33 eV when the annealing temperature was increased.     

Synthesis and characterization of ZnO nanoparticles using polyethylene glycol (PEG)

ZnO nanoparticles and ZnO encapsulated with polyethylene glycol (PEG) was synthesized using zinc acetate as a precursor at low temperature and characterized by different techniques. The influence of the types of solvent, synthesis parameters, and PEG encapsulation on the crystallization, the surface morphology, and the luminescent properties of ZnO nanoparticles prepared by the sol–gel process were investigated. The influence of different addition molar masses of the PEG during the synthesis on the ZnO emission peaks was systematically monitored. The crystallinity, the surface morphology, and the photoluminescence (PL) properties of ZnO depended highly on the synthesis process and PEG encapsulation. X-ray diffraction (XRD) spectra of ZnO nanoparticles show that all the peaks corresponding to the various planes of wurtzite ZnO indicate the formation of a single phase. The absorption edges of these ZnO nanoparticles are shifted by additions of the PEG polymer. The photoluminescence (PL) characterization of the ZnO nanostructures exhibited a broad emission in the visible range with maximum peak at 450 and/or 560 nm.     

Self-aligned nanocrystalline ZnO hexagons by facile solid-state and co-precipitation route

In this study, we report the synthesis of well-aligned nanocrystalline hexagonal zinc oxide (ZnO) nanoparticles by facile solid-state and co-precipitation method. The co-precipitation reactions were performed using aqueous and ethylene glycol (EG) medium using zinc acetate and adipic acid to obtain zinc adipate and further decomposition at 450 °C to confer nanocrystalline ZnO hexagons. XRD shows the hexagonal wurtzite structure of the ZnO. Thermal study reveals complete formation of ZnO at 430 °C in case of solid-state method, whereas in case of co-precipitation method complete formation was observed at 400 °C. Field emission scanning electron microscope shows spherical morphology for ZnO synthesized by solid-state method. The aqueous-mediated ZnO by co-precipitation method shows rod-like morphology. These rods are formed via self assembling of spherical nanoparticles, however, uniformly dispersed spherical crystallites were seen in EG-mediated ZnO. Transmission electron microscope (TEM) investigations clearly show well aligned and highly crystalline transparent and thin hexagonal ZnO. The particle size was measured using TEM and was observed to be 50–60 nm in case of solid-state method and aqueous-mediated co-precipitation method, while 25–50 nm in case of EG-mediated co-precipitation method. UV absorption spectra showed sharp absorption peaks with a blue shift for EG-mediated ZnO, which demonstrate the mono-dispersed lower particle size. The band gap of the ZnO was observed to be 3.4 eV which is higher than the bulk, implies nanocrystalline nature of the ZnO. The photoluminescence studies clearly indicate the strong violet and weak blue emission in ZnO nanoparticles which is quite unique. The process investigated may be useful to synthesize other oxide semiconductors and transition metal oxides.     

Photoluminescence and absorption in sol-gel-derived ZnO films

Highly c-axis-oriented ZnO films were obtained on corning glass substrate by sol-gel technique. The characteristics of photoluminescence (PL) of ZnO, as well as the exciton absorption in the absorption (UV) spectra are closely related to the post-annealing treatment. The difference between PL peak position and the absorption edge, designated as Stokes shift, is found to decrease with the increase of annealing temperature. The minimum Stokes shift is about 150 meV. The decrease of Stokes shift is attributed to the decrease in carrier concentration in ZnO film with annealing. X-ray diffraction, surface morphology and refractive index results indicate an improvement in crystalline quality with annealing. Annealed films also exhibit a green emission centered at ∼520 nm with activation energy of 0.89 eV. The green emission is attributed to the electron transition from the bottom of the conduction band to the antisite oxygen O_Zn defect levels.     

Optical properties of ZnO nanoparticles synthesized by varying the sodium hydroxide to zinc acetate molar ratios using a Sol-Gel process

Material property dependence on the OH⁻/Zn²⁺ molar ratio of the precursor was investigated by varying the amount of NaOH during synthesis of ZnO. It was necessary to control the water content and temperature of the mixture to ensure the reproducibility. It was observed that the structural properties, particle size, photoluminescence intensity and wavelength of maximum intensity were influenced by the molar ratio of the precursor. The XRD spectra for ZnO nanoparticles show the entire peaks corresponding to the various planes of wurtzite ZnO, indicating a single phase. UV measurements show the absorption that comes from the ZnO nanoparticles in visible region. The absorption edge of these ZnO nanoparticles are shifted to higher energies and the determined band gap energies are blue shifted as the OH⁻/Zn² molar ration increases, due to the quantum confinement effects. The photoluminescence characterization of the ZnO nanostructures exhibited a broad emission band centred at green (600 nm) region for all molar ratios except for OH⁻/Zn²⁺ = 1.7 where a second blue emission around 468 nm was also observed. The photoluminescence properties of ZnO nanoparticles were largely determined by the size and surface properties of the nanoparticles.     

A study on the optical and electrical properties of direct-patternable ZnO films incorporated various contents of Pt nanoparticles

Platinum nanoparticles were synthesized by the methanol reduction method, and their size was controlled to 3 nm on average using PVP [poly(N-vinyl-2-pyrrolidon)] as a protecting unit. Various contents of Pt nanoparticles were incorporated into ZnO solutions which were synthesized by a sol-gel process. ZnO films with Pt nanoparticles of various content were annealed at 500 °C and 600 °C for 1 h. The crystallinity increased with the annealing temperature and also slightly with the content of Pt nanoparticles. The sheet resistance of ZnO films decreased with the incorporation of Pt nanoparticles, however the decreasing behavior was not maintained with increasing content of Pt nanoparticles. A shift of valence band maximum energy of ZnO film with Pt nanoparticles to higher energy was also observed due to electron transfer from Pt nanoparticles to ZnO film. The optical transmittance was 88 ± 2% in the visible region for all the ZnO films. Well-defined 60 μm wide direct-patterned ZnO films containing Pt nanoparticles of 0.5 atomic percent could be formed without using dry etching process.     

Structure and photoluminescence of VAC-functionalized ZnO nanoparticles by plasma polymerization

A plasma polymerization method was used to modify the surfaces of ZnO nanoparticles, and the effects of plasma surface modification on photoluminescence (PL) property of ZnO nanoparticles were studied. High-resolution transmission electron microscopy images revealed that a thin film of vinyl acetate (VAC) polymer layer (∼4 nm) was uniformly deposited on the surfaces of the ZnO nanoparticles. The chemical structure of the polymer layer was identified by Fourier transform infrared (FTIR) experiments. The photoluminescence (PL) intensity of the ZnO nanoparticles was found to be significantly decreased by the deposited plasma films. For the particle of smaller size, the ultrathin film indicated better ultraviolet (UV) shielding ability.