一种由椭圆形金属和介质纳米线组成的混合表面等离子体光波导的基模控制特性研究

本文研究了一种由三根并排放置的椭圆形金属-介质-金属纳米线构成的混合表面等离子体光波导所支持的电磁场基模的控制特性,中间是高折射率的介质纳米线,左右是两根对称放置的金属纳米线。研究结果表明,基模电磁场增强效应主要分布在三根纳米线形成的两个间隙区域,且对整个结构的几何参数有一定依赖性。因此,通过改变纳米线的几何尺寸、两根纳米线之间的间距以及介质的电磁参数,可以调整和控制这种波导所支持的基模的有效折射率、模式传输距离、归一化的模式面积和模式束缚因子等物理特性。基于这些有效的模式操控特性,这种混合型的表面等离子体光波导可以应用于高密度光子器件集成、纳米光子学和生物传感器等领域。     

双平行圆柱形MDM纳米棒等离子体波导的传输特性分析

设计了一种由双平行圆柱形纳米棒构成的金属-介质-金属(MDM)型等离子体波导,采用时域有限差分方法(FDTD)分析了波导结构的传输特性。当光波垂直主轴入射时,电磁场被很好地局限在两纳米棒所形成的中间区域以及介质层中,从而在该波导中能够有效地耦合电磁场能量。在工作波长为1 550 nm的情况下,随着内层金属芯半径的增大,有效折射率减小,传播距离增大;而中间介质层厚度增大时,有效折射率增大,传播距离减小。当外层金属壳厚为20 nm时,电场可以很好地被限制在纳米棒的介质层内。上述结果表明:通过调整波导结构的几何参数可以显著提高金属纳米棒的场限制,降低波导本身的损耗, 使波导的有效折射率和传播长度达到最优化。这种等离子体波导能够实现亚波长的光限制,可以应用于光子器件集成和传感器领域。     

基于耦合介质纳米线的深亚波长局域波导

提出了一种基于耦合介质纳米线的深亚波长局域波导,通过两根紧邻的高折射率介质纳米线的耦合,该波导可以将光场有效束缚在纳米线之间的低折射率纳米缝隙中. 计算模拟的结果表明,该波导的有效模场面积达到Λ²₀/200,比单根纳米线波导小一个数量级,这种深亚波长的模场束缚能力可以与表面等离激元混合波导相比拟. 计算模拟的结果还表明,纳米线可能带有的低折射率氧化膜、低折射率衬底的存在、以及纳米线间尺寸存在的一定差异对于该波导结构的实际应用都不会产生很大 关键词： 介质波导 亚波长局域 表面等离激元波导 纳米线     

非线性介质的表面等离子体波导设计和优化

设计了一种基于非线性介质Si-NC/SiO2的混合表面等离子体波导,利用有限元方法定量分析了这种波导所支持基模的能流密度分布、有效折射率、传播长度和有效面积与几何结构参数以及非线性介质的依赖关系.分析结果表明,光场主要被限制在非线性区域,通过调节非线性层的厚度以及非线性比例因子,可以实现模式的有效折射率和传播长度等传输特性参数的调节.固定非线性介质比例因子,有效折射率和传播距离随非线性层厚度增加而增大;固定波导尺寸,有效折射率随比例因子增大而增大,传播距离和有效面积较小.最后,根据分析结果对非线性效应进行优化,优化后波导最优结构尺寸为波导宽度为250nm,非线性材料层厚度为100nm,硅层厚度为150nm.     

新型金属-多层绝缘介质-金属表面等离子波导结构的传输特性

设计了一种新型金属-多层绝缘介质-金属表面等离子波导结构,利用时域有限差分法对其传输特性进行数值分析。研究了有效折射率和传播长度与中间多层绝缘介质厚度之间的关系,并分析了金属层的角度对该波导结构中场分布的影响。结果表明:当光波从波导结构上方垂直入射时,电磁场被限制在多层介质中的高折射率区,实现了场的耦合传输。多层绝缘介质的厚度均为220 nm时,正六边形金属层结构对应的波导结构的传输性能较为理想。该结构能够实现亚波长尺度的光限制,可以应用于光电子集成和传感器领域。     

纳米金属肋混合表面等离子体波导模式特性分析

基于传统混合表面等离子体波导,提出了一种半导体纳米线和纳米金属肋混合的表面等离子体波导.采用有限元法对其模式特性进行了数值模拟,研究了该波导的有效折射率、传播损耗、归一化模场面积等特性随波导几何尺寸的变化规律,分析了该混合波导的增益阈值.结果表明:该波导具有较低的传播损耗和较强的光场限制能力,并且混合模式的最小模面积仅为0.001 52μm2.     

带有开口方环谐振腔的MIM波导的Fano谐振特性研究

本文设计了一种支持Fano谐振传输特性的金属-介质-金属(MIM)型表面等离子体光波导结构,该结构由带有枝节谐振腔的直波导和一个开口方环谐振腔组成。利用数值方法详细研究了Fano谐振传输特性对几何参数的依赖关系,并通过时域耦合模理论(CMT)对给定参数条件下的传输谱进行了拟合验证。同时,也对该结构在折射率传感器方面的应用进行了研究,通过计算介质折射率变化引起的Fano谐振峰的波长变化可以发现,传感器的灵敏度高达1500nm/RIU,品质因子超过1800。这种表面等离子体光波导结构在光子器件集成及纳米滤波器、快速光开关以及折射率传感器等领域有一定的应用前景。     

(Al)GaAs/AlGaAs周期光波导中的等幅基模

本文应用周期介质光波导的模场分布函数和特征方程分析了(Al)GaAs/AlGaAs周期光波导中结构参量及介质折射率对模场分布形状的影响,研究了波导中形成等幅基模的条件,讨论了相应参量的优化选择。     

蝴蝶形中空表面等离子体波导的传输特性

本文设计了一种蝴蝶形中空表面等离子体波导,并对其传输特性进行了研究.采用频域有限差分法,对这种波导所支持的基模的能流密度分布、有效折射率、传播长度和模式面积随几何参数和工作波长的变化关系进行了分析.结果表明:沿纵向的能流主要分布在由四个圆洞所构成的上下两个尖角之间的区域,且越接近尖角,沿纵向的能流越大.对中空圆洞的半径、上下两排圆洞圆心间横向距离和左右两列圆洞圆心间的纵向距离进行调节,模式的有效折射率、传播长度和模式面积也随之变化.在工作波长确定的条件下,相对于b=r/4的情况来说,当b=r/2时,上下两个尖角之间的距离较大,场与金属的相互作用较弱,有效折射率就较大,传播长度也较大.在几何参数确定的条件下,相对于λ=705.0 nm的情形来说,在λ较大时,场的分布范围较大,场与金属表面的接触面积较大,场与金属的相互作用较弱,有效折射率较小,传播距离较长.与由两个和三个空心圆柱构成芯区的表面等离子体波导相比较,蝴蝶形中空表面等离子体波导具有良好的传输特性.如果在波导结构中心填充增益介质,可以克服较大的传播损耗,因此这种蝴蝶形中空表面等离子体波导可以用于光子器件集成领域和传感器领域.     

电光聚合物波导中的锥形结构

提出并设计了一种基于电光聚合物的锥形波导,可用于单模光纤与电光聚合物波导器件之间的连接.锥形波导中采用了宽度锥形和折射率锥形结构.宽度锥形采用劈形形状,通过宽度和折射率的缓慢变化实现模场转换.劈形形状的宽度锥形具有较小的损耗且易于制作,折射率锥形可采用灰度掩膜光刻技术制作.研究了锥形波导的传输损耗与锥形波导的长度、波导宽度和厚度、材料吸收损耗等参数的关系及其优化,分析了锥形波导中的功率传输、模场分布与模式转换效率.结果显示锥形波导的传输损耗小于0.37 dB,光纤-波导-光纤的连接损耗优于1.62 dB,对插入损耗的改善达到8.78 dB,模场转换效率达到了83.7%.     

双椭圆纳米金属棒构成的表面等离子体波导的传输特性分析

设计了一种双椭圆纳米金属棒表面等离子体波导,采用频域有限差分法,对这种波导所支持的基模的能流密度分布、有效折射率和传播长度随几何结构参数和工作波长的依赖关系进行了分析.结果表明,沿纵向的能流主要分布在两个椭圆金属棒所形成的中间区域,且越靠近金属棒的弧形边,沿纵向的能流越大.通过调节两个金属棒的中心距离以及它们的两个半轴的大小,可以调节模式的有效折射率和传播长度.在工作波长确定的条件下,相对于a=b的情形来说,在a<b时,场与金属表面接触的面积较大,场 关键词： 集成光学 光波导 表面等离子体波导     

A long-range hybrid THz plasmonic waveguide with low attenuation loss

Numerical solutions are obtained for the proposed novel hybrid terahertz plasmonic waveguide structure, namely the silicon metal silicon (SMS) waveguide. It is shown that the SMS waveguide can overcome the diffraction limit while still maintaining a sizeable propagation length. The geometric dependence of the mode characteristics of this structure is analyzed in detail, showing strong confinement and low loss with propagation lengths exceeding 14 mm at normalized mode areas of 1.72 × 10⁻². By using the FEM method (Comsol), the guiding properties of the hybrid terahertz surface plasmon polariton (HTSPP) waveguide are numerically analyzed at the THz frequency, and a combination of double-structured comparisons of the best features of the terahertz plasmonic waveguide is made. Depending on the height used and how the mode confinement is measured, various modal designs, such as double microwire structures, are developed. The structures indicate that we verified the possibility of low attenuation loss of hybrid THz plasmonics propagation. The effective mode area A_eff, energy distribution, and propagation length L_p versus height for waveguides with Si microwire and SiO₂ are shown. The numerical calculation results reveal a potential for use in applications such as optical force in trapping and transporting biomolecules, and in high-density integrated circuits.     

Large-core single-mode channel waveguide based on geometrically shaped leaky cladding

We propose a leaky channel waveguide structure for large-mode-area single-mode operation. The proposed structure is characterized by a uniform rectangular core and a specially designed cladding, through which all the confined modes are leaky. Single-mode operation is ensured by choosing the waveguide parameters properly so that the differential leakage loss between the first two modes is sufficiently high. A general power-law cladding geometry profile is considered, which is solved by the effective-index method in conjunction with the transfer-matrix-method to obtain the effective indices and leakage losses of the modes. We show that, with a suitable choice of cladding parameters, the waveguide can demonstrate extended single-mode operation in the wavelength range 750–1600 nm with a core area as large as 100 μm². Such a large confinement area for mode propagation can effectively suppress nonlinear optical effects. The waveguide is expected to find applications in the design of high-power lasers and amplifiers. PACS 42.82.-m; 42.82.Et; 42.79.Gn; 42.55.-f; 42.82.Bq     

An efficient directional coupling from dielectric waveguide to hybrid long-range plasmonic waveguide on a silicon platform

The silicon-based three-dimensional hybrid long-range plasmonic waveguide not only supports long-range propagation distance (~mm) but also has an ultra-small modal area (~10^?2 μm²) at 1.55 μm. Here, we propose a directional coupler for effective coupling from a dielectric slab-waveguide to the hybrid plasmonic waveguide on a silicon platform. Our simulation results show that the coupler is able to excite hybrid long-range plasmonic mode with short coupling length, low insertion loss, and high extinction ratio. With the arm separation of 0.3 μm, the coupling length can be made 5.2 % of the propagation length of the hybrid plasmonic waveguide, while the insertion loss and extinction ratio are ?0.12 and 22.4 dB, respectively. This coupler offers the potential applications in signal routing between the hybrid long-range plasmonic waveguide and dielectric waveguide in the photonic integrated circuits.     

Modelling of finite-size grating waveguide filters on the basis of a free-space diffraction approach

The field reflection coefficient R of a high strength and short length waveguide grating section is obtained by resorting to a free-space diffraction approach whereby the waveguide grating is excited by means of a virtual high index prism. The effective index of the guided mode, the coupling coefficient between contradirectionally propagating modes of the grating waveguide as well as the modal field are first obtained in the case of an infinite grating by interpreting the results given by an exact diffraction solution by means of a three-wave coupled mode formalism. These results are then introduced in the coupled wave analysis of the structure of finite extent to provide the field at the entrance of the waveguide grating section where the usual overlap integral with the incident field delivers the reflection coefficient. We neglect only the result of radiation mode propagation. This assumption can be made when the grating section is longer than the propagating length of all the leaky modes.     

Enhancing surface plasmon polariton propagation by two-layer dielectric-loaded waveguides on silver surface

We report a study of a two-layer dielectric-loaded surface plasmon polariton waveguide (TDLSPPW) which consisted of two dielectric layers (high-index/low-index) on a silver film. The discontinuity of the electric field at the interfaces resulted in a concentrated field in the low-index region. It efficiently reduced the propagation loss of the surface plasmon polariton mode. The mode fields and corresponding complex propagation constants were calculated by a vector finite-difference method. The propagation properties were measured by a modified near-field optical microscope. It is confirmed that the propagation length of the proposed TDLSPPW was about 1.6 times longer than conventional single-layer SPP waveguides. In addition, a 90^° waveguide turn with 3 μm radius showed that the bending loss was smaller than 2 dB.     

Propagation properties of a modified surface plasmonic waveguide with an arc slot

We introduce a modified surface plasmonic waveguide with an arc slot. The dependences of distribution of energy flux density, effective index, propagation length and mode area of the symmetric mode supported by this waveguide on geometrical parameters and working wavelength are analysed by using the finite-difference frequency-domain (FDFD) method. Results show that the energy flux density distributes mainly in four corners which are formed by two arcs, and the closer to the corners it is, the stronger the energy flux density will be. The effective index, the propagation length and the mode area are influenced by geometrical parameters, including the width, the thickness and the arc radius of the surface plasmonic waveguide, as well as the working wavelength. It has been shown that the surface plasmonic waveguide with an arc slot has better propagation properties than the surface plasmonic waveguide with a straight slot. This work may be helpful for applying the slot surface plasmonic waveguide to integrated photonics.     

Modified surface plasmonic waveguide formed by nanometric parallel lines

In this paper, two kinds of modified surface plasmonic waveguides formed by nanometric parallel lines are proposed. The finite-difference frequency-domain method is used to study propagation properties of the fundamental mode supported by these surface plasmonic waveguide structures. Results show that the transverse magnetic field of the fundamental mode is mainly distributed in the face to face region formed by two rods. With the same geometrical parameters and the same working wavelength of 632.8~nm, in the case of rods with a triangular cross-section, the degree of localization of field is strong, i.e. the mode area is small, but the fraction of the modal power in the metal increases, so the effective index increases and the propagation length of the mode decreases. With the same geometrical parameters, relative to the case of a working wavelength of 632.8~nm, when working wavelength is large, the mode area of transverse magnetic field distribution is large, i.e. the degree of localization of field is weak, and the interaction of field and silver is weak too, then the effective index decreases, so the propagation length increases. The rounded radii of rods have a great influence on the performance of the surface plasmonic waveguides with rounded triangular cross-sections, but have little influence on the performance of surface plasmonic waveguides with rounded square cross-sections. Since the distribution of transverse magnetic field, effective index, propagation length and the mode area can be adjusted by the geometrical parameters, this kind of modified surface plasmonic waveguide can be applied to the field of photonic device integration and sensors.     

Modelling of finite-size grating waveguide filters on the basis of a free-space diffraction approach

The field reflection coefficientR of a high strength and short length waveguide grating section is obtained by resorting to a free-space diffraction approach whereby the waveguide grating is excited by means of a virtual high index prism. The effective index of the guided mode, the coupling coefficient between contradirectionally propagating modes of the grating waveguide as well as the modal field are first obtained in the case of an infinite grating by interpreting the results given by an exact diffraction solution by means of a three-wave coupled mode formalism. These results are then introduced in the coupled wave analysis of the structure of finite extent to provide the field at the entrance of the waveguide grating section where the usual overlap integral with the incident field delivers the reflection coefficient. We neglect only the result of radiation mode propagation. This assumption can be made when the grating section is longer than the propagating length of all the leaky modes.