双椭圆纳米金属棒构成的表面等离子体波导的传输特性分析

设计了一种双椭圆纳米金属棒表面等离子体波导,采用频域有限差分法,对这种波导所支持的基模的能流密度分布、有效折射率和传播长度随几何结构参数和工作波长的依赖关系进行了分析.结果表明,沿纵向的能流主要分布在两个椭圆金属棒所形成的中间区域,且越靠近金属棒的弧形边,沿纵向的能流越大.通过调节两个金属棒的中心距离以及它们的两个半轴的大小,可以调节模式的有效折射率和传播长度.在工作波长确定的条件下,相对于a=b的情形来说,在a<b时,场与金属表面接触的面积较大,场 关键词： 集成光学 光波导 表面等离子体波导     

领结形中空表面等离子体波导的传输特性

设计了一种领结形中空表面等离子体波导.采用频域有限差分法,对这种波导所支持的基模的能流密度分布、有效折射率、传播长度和模式面积随几何结构参数和工作波长的依赖关系进行了分析.结果表明,沿纵向的能流主要分布在两个上下突起所形成的中间区域.通过调整几何参数及工作波长,可以调节模式的有效折射率、传播长度和模式面积.在工作波长确定的条件下,有效折射率随突起半径的增大呈减小趋势,而传播长度和模式面积则随着突起半径的增大呈增大趋势,四个角上的圆弧半径对波导的传输特性有微调作用,左右扇形区域的半径对波导的传输特性有较明显 关键词： 集成光学 光波导 表面等离子体波导     

Modified surface plasmonic waveguide formed by nanometric parallel lines

In this paper, two kinds of modified surface plasmonic waveguides formed by nanometric parallel lines are proposed. The finite-difference frequency-domain method is used to study propagation properties of the fundamental mode supported by these surface plasmonic waveguide structures. Results show that the transverse magnetic field of the fundamental mode is mainly distributed in the face to face region formed by two rods. With the same geometrical parameters and the same working wavelength of 632.8~nm, in the case of rods with a triangular cross-section, the degree of localization of field is strong, i.e. the mode area is small, but the fraction of the modal power in the metal increases, so the effective index increases and the propagation length of the mode decreases. With the same geometrical parameters, relative to the case of a working wavelength of 632.8~nm, when working wavelength is large, the mode area of transverse magnetic field distribution is large, i.e. the degree of localization of field is weak, and the interaction of field and silver is weak too, then the effective index decreases, so the propagation length increases. The rounded radii of rods have a great influence on the performance of the surface plasmonic waveguides with rounded triangular cross-sections, but have little influence on the performance of surface plasmonic waveguides with rounded square cross-sections. Since the distribution of transverse magnetic field, effective index, propagation length and the mode area can be adjusted by the geometrical parameters, this kind of modified surface plasmonic waveguide can be applied to the field of photonic device integration and sensors.     

一种基于不平坦基底结构的混合等离子体波导

提出了一种工作于太赫兹波段的、基于半圆柱形"不平坦"InSb基底结构的混合等离子体波导.分析了半导体材料InSb的相对介电常量随工作频率的变化特性,重点研究了该混合波导以及两种不同形变结构的有效模场面积、传播长度、品质因数、能量分布等随波导工作频率、波导尺寸的变化情况.结果表明,本文提出的"不平坦"基底结构波导可以达到与传统结构几乎相同的传播长度,有效模场面积较传统结构减小了一个数量级以上,具有非常强的模场约束性,适合于太赫兹频段高密度集成电路中的应用.     

内壁涂覆石墨烯的双椭圆中空表面等离子波导

本文设计了一种内壁涂覆单层石墨烯的双椭圆形中空表面等离子波导,采用有限元的方法对其传输特性进行了研究。结果表明,椭圆之间的距离和半短轴的长度增大时,有效折射率的实部减小,传输距离增大,模式面积减小;圆化半径增大时,有效折射率的实部增大,传输距离减小,模式面积增大;工作频率增大时,有效折射率的实部减小,传输距离减小,模式面积减小;温度升高时,有效折射率先增大后减小,传输距离减小,模式面积减小。本文的工作为研究基于石墨烯的波导器件提供了理论依据。     

双平行圆柱形MDM纳米棒等离子体波导的传输特性分析

设计了一种由双平行圆柱形纳米棒构成的金属-介质-金属(MDM)型等离子体波导,采用时域有限差分方法(FDTD)分析了波导结构的传输特性。当光波垂直主轴入射时,电磁场被很好地局限在两纳米棒所形成的中间区域以及介质层中,从而在该波导中能够有效地耦合电磁场能量。在工作波长为1 550 nm的情况下,随着内层金属芯半径的增大,有效折射率减小,传播距离增大;而中间介质层厚度增大时,有效折射率增大,传播距离减小。当外层金属壳厚为20 nm时,电场可以很好地被限制在纳米棒的介质层内。上述结果表明:通过调整波导结构的几何参数可以显著提高金属纳米棒的场限制,降低波导本身的损耗, 使波导的有效折射率和传播长度达到最优化。这种等离子体波导能够实现亚波长的光限制,可以应用于光子器件集成和传感器领域。     

Guided subwavelength slow-light mode supported by a plasmonic waveguide system

We introduce a plasmonic waveguide system, which supports a subwavelength broadband slow-light guided mode with a tunable slowdown factor at a given wavelength. The system consists of a metal-dielectric-metal (MDM) waveguide side-coupled to a periodic array of MDM stub resonators. The slowdown factor at a given wavelength can be tuned by adjusting the geometrical parameters of the system. In addition, there is a trade-off between the slowdown factor and the propagation length of the supported optical mode. Finally, we show that light can be coupled efficiently from a conventional MDM waveguide to the plasmonic waveguide system.     

涂覆双层石墨烯的介质纳米线表面等离子体光波导的模式特性研究

设计了一种由涂覆双层石墨烯的圆形介质纳米线组成的表面等离子体光波导。利用有限元法(FEM),数值分析了纳米线半径、介质夹层厚度、石墨烯化学势以及工作频率对波导所支持的电磁场模式的有效折射率、传播长度、归一化模式面积以及品质因数等模式特性的影响。结果表明,这种新型的混合表面等离子体光波导具有很强的模式束缚能力,归一化模式面积非常小,可以实现极高密度的器件集成,并且传输损耗较低。     

Design and analysis of a vertical directional coupler between a three-dimensional plasmonic slot waveguide and a silicon waveguide

The design of a vertical directional coupler between a three-dimensional plasmonic slot waveguide and a silicon waveguide is theoretically investigated in detail. It consists of two steps: the design of isolated plasmonic slot waveguide and silicon waveguide and the determination of the gap between the two waveguides and the length of a coupling region. The designed structure transfers 70.8% of the power carried by the silicon waveguide mode to the plasmonic slot waveguide mode when the gap is 150 nm and the coupling length is 2.14 μm. The wavelength dependence of our vertical directional coupler is also studied. The analysis shows that the amount of the transferred power changes slightly over a very wide wavelength range between 1.40 μm and 1.61 μm. Moreover, if we employ the fabrication technology for silicon photonics, it is quite tolerant to the variation of the length of its coupling section. Finally, the vertical directional coupler is considered for a polarizer.     

梳状波导结构中石墨烯表面等离子体的传播性质

理论上研究了介质/石墨烯/介质梳状波导结构中表面等离子体的传播性质. 波导中表面等离子体模的有效折射率随着石墨烯费米能级的提高而减小, 随着介质折射率的增加而增加. 分析和仿真结果表明, 基于这种梳状波导可以在中红外波段实现新型的纳米等离子体滤波器, 器件的尺度在几百纳米的范围. 通过改变梳状分支的长度, 石墨烯的费米能级, 介质的折射率和波导中石墨烯的层数, 很容易来调节带隙的位置. 另外, 滤波带隙的宽度随着梳状分支数的增加而增加. 这种滤波性质将在可调的高集成光子滤波器件中具有潜在的应用.     

Vertical coupling characteristics between hybrid plasmonic slot waveguide and Si waveguide

For development of complementary metal–oxide–semiconductor (CMOS)-compatible integrated optical circuits, vertical directional coupling between a hybrid plasmonic slot waveguide and a Si waveguide is theoretically investigated in detail. To determine the vertical separation gap and efficient coupling length, we investigate the characteristics of the even and odd supermodes at a wavelength of 1.55 μm. The vertical coupler transfers 90% of the power carried by the Si waveguide to the hybrid plasmonic slot waveguide after normalizing to reference waveguides when the gap is 60 nm and the coupling length is 2.6 μm. Because of the lossy hybrid guided mode in the plasmonic waveguide, the transmitted power exhibits damped sinusoidal behavior depending on the overlapping length. The proposed vertical coupler shows more efficient light coupling between a dielectric and plasmonic waveguide in comparison to the other types of hybrid coupler, and can be exploited further for on-chip integrated opto-electronic circuits.     

Enhancing Bremsstrahlung production from ultraintense laser-solid interactions with front surface structures

A new type of a coaxial multi-layer plasmonic waveguide is proposed. The mode propagation properties are analyzed at the communication working wavelength. Theoretical investigations reveal that the enhanced optical confinement can be achieved in the two low-index dielectric media layers. The mode size can be sub- or deep sub-wavelength scale. The mode propagation loss can be well compensated by replacing the high-index dielectric media with gain material to achieve longer propagation length with better mode confinement. The comparisons of the mode properties between the proposed waveguide and waveguides studied in the published literatures are also considered. These investigations potentially lay the groundwork for the further applications of nanowire type multilayer hybrid structures. This structure could also enable various applications such asnanophotonic waveguides, high-quality nanolasers, and optical trapping and biosensors.     

An efficient directional coupling from dielectric waveguide to hybrid long-range plasmonic waveguide on a silicon platform

The silicon-based three-dimensional hybrid long-range plasmonic waveguide not only supports long-range propagation distance (~mm) but also has an ultra-small modal area (~10^?2 μm²) at 1.55 μm. Here, we propose a directional coupler for effective coupling from a dielectric slab-waveguide to the hybrid plasmonic waveguide on a silicon platform. Our simulation results show that the coupler is able to excite hybrid long-range plasmonic mode with short coupling length, low insertion loss, and high extinction ratio. With the arm separation of 0.3 μm, the coupling length can be made 5.2 % of the propagation length of the hybrid plasmonic waveguide, while the insertion loss and extinction ratio are ?0.12 and 22.4 dB, respectively. This coupler offers the potential applications in signal routing between the hybrid long-range plasmonic waveguide and dielectric waveguide in the photonic integrated circuits.     

Efficient second-harmonic generation in nonlinear plasmonic waveguide

We theoretically studied a nonlinear optical process in a hybrid plasmonic waveguide composed of a nonlinear dielectric waveguide and a metal film with a separation of a thin air gap. Owing to the hybridization effect of guided mode and surface plasmon polariton mode, this particular waveguide is able to confine the optical-field in a deep subwavelength scale together with low propagation loss. Based on this, efficient second-harmonic generations (SHG) were revealed at the fundamental wavelength of λ=1.55?μm with good field confinement. The SHG efficiency, as well as the coupling coefficient and mode area, were analyzed and discussed in detail with respect to the structural parameters.     

Wave propagation in deep-subwavelength mode waveguides

This Letter proposes a dielectric waveguide with deep-subwavelength mode sizes. Results of both frequency domain and time domain analysis show that the effective mode area is below λ(0)(2)/400 and can even reach λ(0)(2)/1000 (λ(0) is the wavelength in vacuum). The effective electrical mode area can be comparable to that of a hybrid plasmonic subwavelength confinement waveguide, with reduced optical absorption. In contrast to slot waveguides, which guide light in low-index materials, the proposed structure guides light in high-index materials. Results obtained in this Letter show that the losses are sensitive to the surface roughness on the tens of nanometers scale. The structure can be used to design ring resonators with a quality factor comparable to that of a diffraction-limited dielectric ring resonator with the same standing wave numbers. The property can be applied in nonlinear effect enhancement or laser design with ultralow threshold.     

Two-dimensional light confinement in cross-index-modulation plasmonic waveguides

We report a numerical study of plasmonic waveguides that localize light in two dimensions at a cross section of 4.2 nm × 2.1 nm with the propagation length of 38 μm. By varying the geometrical parameters, strong mode confinements (range from λ(2)/3352 to λ(2)/2557525) are achieved with controllable propagation distance (44.68-40.988 μm), and mode size below 1 nm(2) has been demonstrated for the first time. Furthermore, a cross-index-modulation mechanism is proposed to explain the strong field localization behavior, providing guidelines for future waveguide designs.     

A long-range hybrid THz plasmonic waveguide with low attenuation loss

Numerical solutions are obtained for the proposed novel hybrid terahertz plasmonic waveguide structure, namely the silicon metal silicon (SMS) waveguide. It is shown that the SMS waveguide can overcome the diffraction limit while still maintaining a sizeable propagation length. The geometric dependence of the mode characteristics of this structure is analyzed in detail, showing strong confinement and low loss with propagation lengths exceeding 14 mm at normalized mode areas of 1.72 × 10⁻². By using the FEM method (Comsol), the guiding properties of the hybrid terahertz surface plasmon polariton (HTSPP) waveguide are numerically analyzed at the THz frequency, and a combination of double-structured comparisons of the best features of the terahertz plasmonic waveguide is made. Depending on the height used and how the mode confinement is measured, various modal designs, such as double microwire structures, are developed. The structures indicate that we verified the possibility of low attenuation loss of hybrid THz plasmonics propagation. The effective mode area A_eff, energy distribution, and propagation length L_p versus height for waveguides with Si microwire and SiO₂ are shown. The numerical calculation results reveal a potential for use in applications such as optical force in trapping and transporting biomolecules, and in high-density integrated circuits.     

扇形波导谐振宽边纵缝的归一化电导

扇形波导可作为高功率微波圆柱共形波导缝隙阵天线的基本单元。分析了扇形波导中主模场分量,根据实际情况对主模场进行了合理近似。采用互易定理推导由波导主模横向场分量和缝隙场分量表示的波导场分量的前向或后向散射系数。根据波导传输线理论,将波导宽边纵缝等效为并联导纳,再根据波导边界条件得到扇形波导宽边谐振纵缝的归一化电导与波导散射系数之间的关系式。根据缝隙天线与振子天线的互补关系得到扇形波导谐振缝隙的辐射阻抗,结合波导功率平衡关系得到由波导横向场散射系数表示的缝隙辐射功率表达式,得到归一化电导的与谐振宽边纵缝的偏移位置、缝隙宽度、波导波长以及扇形波导尺寸参数之间的解析表达式。给出了算例,在波导中间区域,通过商用软件计算得到的电导与理论公式结果基本吻合。     

涂覆石墨烯的非对称并行电介质纳米线波导的模式特性分析

采用多级展开方法,对涂覆石墨烯的非对称并行电介质纳米线波导的模式特性进行了分析.首先对这种波导中的表面等离子模式进行分类,然后对七种低阶模式的有效折射率和传播长度随工作频率、几何结构参数和石墨烯费米能的依赖关系进行详细的分析.结果表明,通过改变工作频率、几何结构参数和石墨烯的费米能,可以在较大范围内调节模式的特性.与有限元法进行的对比表明,基于多级方法的半解析结果与有限元法的数值结果非常符合.研究结果可为涂覆石墨烯的非对称并行电介质纳米线的设计和制作提供一定的理论基础.     

紫外表面等离激元在基于氧化锌纳米线的半导体-绝缘介质-金属结构中的输运特性研究

研究了紫外表面等离激元在半导体纳米线-绝缘介质-金属构成的波导结构中的输运问题,借助有限元方法,对这种波导所支持导模的电磁能分布、有效折射率、传播长度和有效模场面积随电磁参数和几何结构参数的依赖关系进行了分析.计算结果表明:以氧化锌纳米线作为增益介质,绝缘材料选择折射率小的空气,金属选择铝能够实现对输出光场的亚波长约束,有效模场面积达到λ2/100,同时保持低的传输损耗和高场强限制能力;有望用作纳米光源,使得相关的生物探测器件和医疗诊断设备实现更高的灵敏度和更小的体积.