电脉冲对多晶La0.7Ca0.3MnO3比热的影响

对电脉冲诱导的不同电阻态下La_0.7Ca_0.3MnO₃样品的比热进行了研究.实验结果表明,电脉冲导致La_0.7Ca_0.3MnO₃样品比热随电阻状态发生可逆变化.比热随电阻状态的减小而减小.低温比热拟合及不同电阻状态下的比热差与温度关系说明,声子对比热的贡献不随电阻状态变化,磁性和载流子对比热的贡献是导致La_0.7Ca_0.3MnO₃样品比热变化的原因.电脉冲诱导O离子沿一维扩展性缺陷的电化学迁移,导致材料中局部区域的O离子浓度发生变化.O离子浓度的变化导致载流子浓度的变化,同时载流子浓度的变化将使得低温下磁性耦合强度发生变化,从而导致比热发生变化.     

Influences of Li Intercalation on the Electronic Structures of O2p and V3d Orbitals in α-V2O5

运用第一性原理计算了锂嵌入对α-V₂O₅中O2p和V3d轨道电子结构的影响. 计算结果表明,不同的锂嵌入位置对O2p和V3d轨道的电子结构有着不同的影响. 但锂的嵌入会减弱了V₂O₅中V=O1键,同时导致V3d导带的劈裂变窄或消失和O2p价带变宽. 最后计算出从每个Li2s轨道到V3d轨道的电子传递数为0.52.     

新型光存储材料Sr2SnO4: Tb3+, Li+ 的合成及其红外上转换光激励发光性能的研究

采用高温固相法获得了一种只具有 微弱余辉的新型电子俘获型光存储材料Sr₂SnO₄:Tb^{3 +}, Li ⁺. 发光性能研究结果表明: 该材料对980 nm的红外激光具有很好的上转换光激励信息读出响应, 同时292 nm紫外光为其最佳信息写入光源. 光存储性能研究结果表明: 该材料的浅陷阱较少, 因此其余辉发光很弱, 不到500 s; 另一方面, 该材料中存在大量的深蓄能陷阱. 因此, Sr₂SnO₄: Tb^{3 +}, Li⁺是一种具有较好实际应用价值的新型电子俘获型光存储材料. 此外, 还讨论了Sr₂SnO₄: Tb^{3 +}, Li⁺的光存储发光机理.     

沉积于MgO基片上的La0.7Ca0.3MnO3薄膜的应变弛豫和磁电阻特性

利用90°离轴射频磁控溅射方法将La_0.7Ca_0.3MnO₃(LCMO)沉积于(001)取向的MgO单晶基片上,薄膜厚度变化范围为5nm到200nm. 通过掠入射X射线衍射技术测量了LCMO/MgO薄膜的面内晶格常数, 结合常规X射线衍射研究了LCMO薄膜的晶格应变及其弛豫情况, 用四探针法测量了薄膜的磁电阻特性.结果表明, LCMO/MgO薄膜均为(001)取向生长, 在厚度小于5nm时已经发生应变弛豫, 当薄膜厚度为100nm以上时, 薄膜的微应变接近于完全弛豫, 并表现出与块体材料类似的磁电阻特性, 具有较大的磁电阻和较高的磁电阻峰值温度.     

氧非正分La0.9Ba0.1MnO3-δ/SrTiO3:Nb p-n异质结的整流特性研究

利用脉冲激光沉积技术在掺Nb的SrTiO₃衬底上制备了氧非正分La_0.9Ba_0.1MnO_3-δ/SrTiO₃:Nb p-n异质结.在20—300K这一较宽的温度范围内获得了光滑的整流曲线.整流实验表明：该p-n异质结的正向扩散电压V_D随着温度升高在薄膜金属—绝缘转变温度附近出现极大值，表现出与氧正分La_0.9Ba_0.     

一种印刷型薄膜太阳能电池p-n结调制技术

能带值为0.5~0.85 eV材料的稀缺是多结太阳能电池面临的一个主要挑战,本文使用非真空的机械化学法合成了能带值为0.83 eV的Cu₂SnS₃化合物,使用印刷技术将其制备成吸收层薄膜,并采用superstrate太阳能电池结构(Mo/Cu₂SnS₃/In₂S₃/TiO₂/FTO glass)对其光伏特性进行了研究.实验表明所制备的太阳能电池短路电流密度、开路电压、填充因子和转换效率分别为12.38 mA/cm²、320 mV、0.28和1.10%.此外,为更好地满足多结太阳能电池对电流匹配的需求,本文对所制备太阳能电池的Cu₂SnS₃/In₂S₃ p-n结进行了分析.通过在p-n结界面植入一层薄的疏松缓冲层,使调制后的太阳能电池短路电流密度从最初的12.38 mA/cm²增加到了23.15 mA/cm²,相应太阳能电池转换效率从1.1%增加到了1.92%.该p-n调制技术对印刷型薄膜太阳能电池具有重要借鉴意义.     

金属阳离子和水对MnO2晶体稳定性的重要影响

利用密度泛函方法对具有代表性的α、β、δ三种MnO₂晶体结构和能量进行了系统的计算,探讨金属离子和水对MnO₂的晶体稳定性的影响．计算结果表明α-MnO₂在没有隧道中钾离子支撑的情况下会崩溃;δ-MnO₂在夹层中没有金属阳离子和水存在时,层间距会明显低于实验结果．从能量来看,在金属阳离子和(或)水存在的条件下α-MnO2和δ-MnO2会比β-MnO2更加稳定, 反之则没有β-MnO2稳定．因此,金属离子和水是层状MnO₂和较大隧道状MnO₂晶体存在的必要条件之一．     

Heusler合金Li2AlX(X=Ga，In)的晶格动力学和电子特性

本文计算了Heusler合金Li₂AlGa和Li₂AlIn的晶格参数、体积模量、体积模量的一阶导数、 电子能带结构、声子色散曲线和声子态密度,并与密度泛函理论中的广义梯度近似计算结果进行比较. 计算的晶格参数与文献有很好的一致性. 两个Heusler合金的电子能带结构表明它们是半金属结构. 并利用声子色散曲线和声子密度图研究Heusler合金晶格动力学. Li₂AlGa和Li₂AlIn Heusler合金在基态呈现动力学稳定.     

氧化还原可逆Nb2TiO7复合阴极电解池高温水蒸气电解研究

系统地研究Nb₂TiO₇与Nb_1.33Ti_0.67O₄材料相互转变的氧化还原循环可逆性能,同时研究Nb2TiO7和Nb_1.33Ti_0.67O₄样品随温度和氧分压变化的电导率,并与复合电极对称电池和电解池的电化学性能相关联. 在830 oC下,对Nb_1.33Ti_0.67O₄复合电极电解池进行水蒸气的电解研究测试. 电流电压曲线和电解池短期性能测试表明在低电压下主要为电极的还原和活化过程;而在高电压下主要为水蒸气的电解. 当3%H₂O/Ar/4%H_{2气体通入阴极时电解池水蒸气电解的法拉第效率为98.9%;而当通入气体转换为3%H2O/Ar时效率为89%.}     

通过掺杂V和F提高碳包覆的磷酸铁锂锂离子电池的电化学性能

在原位聚合合成方法的基础上,结合两步烧结过程制得LiFe_1-xV_x(PO₄)_(3-y)/₃F_y/C.V和F掺杂对碳包覆的磷酸铁锂材料的结构、形貌和电化学性能有影响.通过XRD、FTIR、SEM、充/放电测试和电化学阻抗谱对材料的结构、形貌和电化学性能进行了表征.结果表明,V和F的掺杂并没有破坏橄榄石结构中的LiFePO₄/C,但可以提高晶体结构的稳定,降低电荷的转移阻抗,提高锂离子扩散速度,改善了LiFePO₄/C材料的循环性能和高倍率性能.     

Structural and electronic properties of the Li-ion battery cathode material LixCoSiO4

The first-principles density functional theory has been employed to study the structural and electronic properties of Li_xCoSiO₄. The lattice stability of Li_xCoSiO₄ during the lithiation–delithiation process is discussed. The changes in the electronic structures of Li_xCoSiO₄ during the deintercalation of Li ions are also probed. It is found that Li₂CoSiO₄ reacts reversibly with 1 Li⁺ at an average voltage of 4.1 V versus a lithium anode. The computational results indicate that Li₂CoSiO₄ material is a potential candidate for high-capacity cathode for advanced lithium ion batteries.     

Sn3InSb4合金嵌Li性能的第一性原理研究

采用第一性原理超软赝势平面波方法计算了Sn₃InSb₄的嵌Li性能,得到各种嵌Li相的嵌Li形成能、理论质量比容量、体积膨胀率、能带结构、态密度和差分电荷密度等.从能量角度分析,Li在嵌入时,优先占据晶胞的四面体间隙位置,然后逐步挤出处于节点位置的Sn原子和In原子.在嵌Li过程中,材料表现出较大的体积膨胀率(11.74%-43.40%),这是导致Sn₃InSb₄作为Li离子电极材料循环性能差的重要原因.态密度计算表明,体系的导电性能首先随嵌Li量的增加而增加,当所有的间隙位置被Li填满,发生Sn的替换反应时,富Li态合金相的导电性反而下降.     

Preparation and characterization of Li2CoMn3O8 thin film cathodes for high energy lithium batteries

An ion layer gas reaction (ILGAR) dip-coating process for the deposition of homogeneous spinel structured Li₂CoMn₃O₈ thin layers has been developed. Thin film cathodes for use in high-energy density lithium batteries with thicknesses of about 200 nm have been prepared. The films were found to be X-ray amorphous after preparation. After annealing at 700°C in air for 2 h, the spinel structure of Li₂CoMn₃O₈ was observed by X-ray diffraction analysis. The composition of the surface was studied by XPS, which indicated enhanced Li and Mn concentrations as a result of the rinsing process and different solubilities of the precursor salts. The electrochemical behavior was investigated by separating the annealed electrode sample from a conventional organic lithium ion-conducting electrolyte by a layer of LiPON solid electrolyte and using elemental lithium as counter electrode. A capacity of 110.8 mAh/g was observed which is related to the valence changes of Mn and Co in the spinel structure.     

Phase separation of intercalation electrodes

Lithium ion cells are widely used for portable equipment because of their high energy density. These cells employ lithium intercalation materials as their anode and cathode active materials. Lithium intercalation materials sometimes show phase separation as a function of the amount of inserted Li, and the cell voltage becomes a constant at the two-phase region. The thermodynamic criterion of the phase separation of binary mixtures is already known using Gibbs free energy. The criterion of the phase separation was applied to that of lithium intercalation materials. First, the phase separation of spinel LiMn₂O₄ and LiNiO₂ was studied, with the assumption that the cathode materials do not deform during Li insertion and extraction, are completely ionic, and only the Coulomb potential is effective in terms of changing the internal energy. Our calculated phase separation was in agreement with the experiments at 0<x<0.5 for Li_xMn₂O₄ and 0<x<0.25 for Li_xNiO₂. Our calculated voltage of Li_xMn₂O₄ was very high compared with the experimental value, because of a very low value of the Coulomb potential at the lithium tetrahedral site in Li_xMn₂O₄. Therefore, it seems that LiMn₂O₄ is not a perfect ionic crystal. Next, the phase separation of graphite was studied, considering a work (w_a) to expand the layer when Li is inserted. When w_a is small, it is expected that the phase separation is the co-existence of the Li-poor phase and the Li-rich phase. However, if w_a is large, it is expected that the two-phases are a phase without Li and a phase filled with Li completely. From these considerations, graphite seems to have a large w_a. Paper presented at the 8th EuroConference on Ionics, Carvoeiro, Algarve, Portugal, Sept. 16–22, 2001.     

Atomic force microscopy study of surface morphology change in spinel LiMn2O4: Possibility of direct observation of Jahn-Teller instability

Surface morphology in 3.5 × 3.5 μm² area of spinel LiMn₂O₄, which is a typical cathode material for Li ion secondary batteries, is studied using an atomic force microscopy (AFM) with a conductive probe. Negative bias voltage is applied to the probe to attract Li⁺ ions toward LiMn₂O₄ surface during the AFM observation. Before applying the voltage (0 V), the whole LiMn₂O₄ surface is covered with scale-shaped grains. Under the negative voltage of 5.5 V, electric current abruptly increases, indicating Li⁺ ionic conduction. Simultaneously, part of the scale-shaped grains expand and flatten. Jahn-Teller phase transition, which is induced by the repulsive interaction between the Mn-e_g and O-2p electrons in Li accumulated layer, is proposed as a possible origin of these results.     

LixFePO4(x=0.0, 0.75, 1.0)电子结构与弹性性质的第一性原理研究

采用基于密度泛函理论的第一性原理研究方法,计算了不同嵌锂态Li_xFePO₄(x=0,0.75,1.0)的电子结构. 对于橄榄石型Li_xFePO₄正极材料,虽然Fe3d电子在费米能级附近相互交错,但由于受晶体场作用的限制,并不能真正成为自由电子,Fe3d电子对体系的导电性没有很大贡献,而Fe—O键在低能成键区形成p-d杂化的局域态共价键对稳定合金骨架具有重要作用. 随着锂离子的脱 关键词： 锂离子电池 4')" href="#">LiFePO₄ 电子结构 弹性性质     

Spinel lithium titanate (Li4Ti5O12) as novel anode material for room-temperature sodium-ion battery

This is the first time that a novel anode material, spinel Li₄Ti₅O₁₂ which is well known as a “zero-strain” anode material for lithium storage, has been introduced for sodium-ion battery. The Li₄Ti₅O₁₂ shows an average Na storage voltage of about 1.0 V and a reversible capacity of about 145 mAh/g, thereby making it a promising anode for sodium-ion battery. E_x-situ X-ray diffraction (XRD) is used to investigate the structure change in the Na insertion/deinsertion process. Based on this, a possible Na storage mechanism is proposed.     

Organic acid assisted solid-state synthesis of Li1.2Ni0.16Co0.08Mn0.56O2 nanoparticles as lithium ion battery cathodes

Lithium-rich layered oxide Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ can be referred as a crystalline mixture of Li₂MnO₃ and LiNi_0.4Co_0.2Mn_0.4O₂ at equal molar ratio. In the paper, the solid state reaction of M(AC)₂·4H₂O (M = Mn, Co and Ni) and LiOH·H₂O has been performed to obtain nanocrystalline Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ using a small molecular organic acid (i.e., oxalic acid (OA), citric acid (CA) or tartaric acid (TA)) as additive. The introduction of organic acids can help to improve the layered structure and inhibit the particle growth of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂, and the different organic acids exert distinct influences on the structural and electrochemical properties of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂. In detail, the nanoparticles obtained in the presence of OA have the smallest average size of 50–150 nm, which correspondingly exhibit the highest initial discharge capacity of 267.52 mAh g⁻¹ at 0.1C and the best high-rate capability (e.g., 152.22 mAh g⁻¹, 5C) when applied as a lithium ion battery cathode. Furthermore, the active substance obtained from TA shows the best cycling stability and a discharge capacity of 202.42 mAh g⁻¹ can be retained after 50 cycles at 0.5C.     

Magneto-transport properties of La0.7Ca0.3MnO3/SrTiO3/La0.7Ce0.3MnO3 tunnel junction

Hole-doped rare-earth manganite La_0.7Ca_0.3MnO₃ and the electron-doped manganite La_0.7Ce_0.3MnO₃ both show a metal-insulator transition around 250 K associated with a ferromagnetic transition and colossal magnetoresistance. In an earlier publication we have reported the rectifying characteristic of La_0.7Ca_0.3MnO₃/SrTiO₃/La_0.7Ce_0.3MnO₃ tunnel junction at room temperature, showing that it is possible to fabricate a diode out of the polaronic insulator regime of doped manganites. Here we report the magneto-transport properties of such a tunnel junction above and below the metal-insulator transition. We show, from the large positive magnetoresistance of the tunnel junction at low temperature, that La_0.7Ce_0.3MnO₃ could be a minority spin carrier ferromagnet. The implication of this observation is discussed.