热效应对纳米焊接界面结构的影响

采用分子动力学方法深入研究热效应对纳米焊接界面结构的影响。具体分析了碳管直径和时间的变化对界面结构的影响规律,并详细给出了1530 K下的焊接过程。结果表明,除碳管(5,5)外,碳管(6,6),(7,7),(9,9),(11,11)中纳米线形成的时间分别为13.8, 14.6, 17.5, 19.6 ps。纳米线是由单根或多根Ni原子链组成,碳管(6,6),(7,7),(9,9),(11,11)中Ni原子链数分别为1,3,7和16。界面结构包括内部焊接和外部焊接。内部焊接的临界直径由碳管(6,6)决定,其值为0.814 nm。在同一时刻,大直径的碳管可获得更大的外部接触长度。外部接触长度的增长速率随碳管直径的增加而增大,接触长度的最大增长速率可达0.013 nm/ps。最后确定了界面结构形成临界温度,发现对于相同直径碳管,外部焊接的临界温度高于内部焊接的临界温度,临界温度与碳管直径无关。     

TEM纳米云纹法测量纳米碳管变形

提出了透射电子显微镜(TEM)纳米云纹法的新技术,首次将该方法用于单根单壁碳纳米管的残余变形测量。纳米云纹由计算机显示器扫描线与碳纳米管束TEM图像干涉而成。该方法具有纳米级空间分辨率,可直接测量碳纳米管的力学性能。对TEM纳米云纹法的原理进行了详细的阐述,并利用不同管径的单壁碳管束产生了云纹。对直径为7.5nm的弯曲碳管束的残余变形进行测量,直接得到了其中一根直径为1.0nm的单壁碳管的残余变形场。实验结果证明了该方法的可行性。该方法为纳米尺度的碳管力学性能测量提供了新途径。     

The structure and dynamics of water inside armchair carbon nanotube

In this paper we present some simulation results about the behaviour of water molecules inside a single wall carbon nanotube (SWNT). We find that the confinement of water in an SWNT can induce a wave-like pattern distribution along the channel axis, similar phenomena are also observed in biological water channels. Carbon nanotubes(CNTs) can serve as simple nonpolar water channels. Molecular transport through narrow CNTs is highly collective because of tight hydrogen bonds in the protective environment of the pore. The hydrogen bond net is important for proton and other signal transports. The average dipoles of water molecules inside CNTs (7,7), (8,8) and (9,9) are discussed in detail. Simulation results indicate that the states of dipole are affected by the diameter of SWNT. The number of hydrogen bonds, the water--water interaction and water--CNT interaction are also studied in this paper.     

Formation mechanism of carbon nanotubes in the gas-phase synthesis from colloidal solutions of nanoparticles

Single- and multi-wall carbon nanotubes have been synthesized by the gas-phase catalytic reaction of colloidal solutions of metal nanoparticles using a vertical flow reactor. The reverse micelle solution of the Co–Mo nanoparticles with the mean diameter of 11 nm dissolved in toluene was injected directly into the reactor maintained at 1200 °C. The nanoparticles and the solvent act as the catalyst and carbon source, respectively. When the concentration of the thiophene additive is low (1 wt.%), the formation of SWNT bundles preferentially occurred. The SWNT bundles were present together with the relatively small metal nanoparticles with the diameter of 0.5–5.5 nm. It is likely that the original nanoparticles with the diameter of 11 nm break into smaller ones, 1–2 nm diameters, which is suitable for the SWNT growth. The synactic effect of Co and Mo was also observed.     

Solid-state Er:Yb:glass laser mode-locked by using single-wall carbon nanotube thin film

We design single-wall carbon nanotube (SWNT) thin-film saturable absorbers (SAs) integrated onto semiconductor distributed Bragg reflectors for mode-locking solid-state Er:Yb:glass lasers. We characterize the low nonsaturable loss, high-damage-threshold SWNT SAs and verify their operation up to a pulse fluence of 2 mJ/cm(2). We demonstrate passive fundamental continuous-wave mode locking with and without group-delay dispersion compensation. Without compensation the laser produces chirped 1.8 ps pulses with a spectral width of 3.8 nm. With compensation, we obtain 261 fs Fourier-transform-limited pulses with a spectral width of 9.6 nm.     

Surfactant-nanotube interactions in water and nanotube separation by diameter: atomistic simulations

A non-destructive sorting method to separate single-walled carbon nanotubes (SWNTs) by diameter was recently proposed. By this method, SWNTs are suspended in water by surfactant encapsulation and the separation is carried out by ultracentrifugation in a density gradient. SWNTs of different diameters are distributed according to their densities along the centrifuge tube. A mixture of two anionic surfactants, namely sodium dodecylsulfate (SDS) and sodium cholate (SC), presented the best performance in discriminating nanotubes by diameter. Unexpectedly, small diameter nanotubes are found at the low density part of the centrifuge tube. We present molecular dynamics studies of the water-surfactant-SWNT system to investigate the role of surfactants in the sorting process. We found that surfactants can actually be attracted towards the interior of the nanotube cage, depending on the relationship between the surfactant radius of gyration and the nanotube diameter. The dynamics at room temperature showed that, as the amphiphile moves to the hollow cage, water molecules are dragged together, thereby promoting the nanotube filling. The resulting densities of filled SWNT are in agreement with measured densities.     

Molecular dynamics simulations of hydrogen adsorption/desorption by palladium decorated single-walled carbon nanotube bundle

Utilising molecular dynamics simulations, the hydrogen molecules adsorption isotherms of the (8,?0) palladium decorated single-walled carbon nanotube (SWNT) were obtained. The hydrogen adsorption was studied on the external, interstial and internal surfaces of the SWNT bundle at several temperatures ranging from 77 to 400?K. The results were compared with the bare single-walled carbon nanotube bundle under the same conditions. The decorated carbon nanotube bundle hydrogen adsorption was significantly higher than that of the bare one. The hydrogen desorption and readsorption were studied using temperature as the readsorption/desorption variable. The rate constants were calculated for the hydrogen desorption at different temperatures. The calculated decorated SWNT bundle hydrogen desorption activation energy was higher than that for the bare SWNT bundle. The calculated activation energies for the hydrogen desorption in both nanotube bundles specified the temperature dependency of hydrogen desorption.     

X-ray irradiation effect of double walled carbon nanotube

We have studied double-walled carbon nanotube (DWNT) irradiated by soft X-ray by Raman scattering spectroscopy and the spectral characteristics are compared to single-walled carbon nanotube (SWNT) irradiated under the same condition. We proved that DWNT is more stable for the X-ray induced defect formation than SWNT. Moreover, we found that the outer tube of DWNT was more sensitive on X-ray irradiation than the inner tube. The defect was recovered by annealing in Ar at lower temperature than that of SWNT. Based on these results, we inferred that X-ray irradiation leads to formation of interstitial-vacancy pairs, Frenkel defects, in carbon nanotube. The interstitial-vacancy separation on the inner tube of DWNT is conceivably shorter than that of the outer tube.     

Carbon nanotubes adhesion and nanomechanical behavior from peeling force spectroscopy

Applications based on single walled carbon nanotube (SWNT) are good example of the great need to continuously develop metrology methods in the field of nanotechnology. Contact and interface properties are key parameters that determine the efficiency of SWNT functionalized nanomaterials and nanodevices. In this work we have taken advantage of a good control of the SWNT growth processes at an atomic force microscope (AFM) tip apex and the use of a low noise (10⁻¹³ m/√Hz) AFM to investigate the mechanical behavior of a SWNT touching a surface. By simultaneously recording static and dynamic properties of SWNT, we show that the contact corresponds to a peeling geometry, and extract quantities such as adhesion energy per unit length, curvature and bending rigidity of the nanotube. A complete picture of the local shape of the SWNT and its mechanical behavior is provided.     

基于碳纳米管分子封装的一维电子波函数扫描

利用第一性原理,设计并研究了一类基于单臂碳纳米管的分子封装的分子体系．计算表明,半环葫芦脲类化合物可有效封装碳纳米管,引入微弱的分子间相互作用,对碳纳米管的电子态能级结构分布 仅带来微弱影响．半环葫芦脲分子与碳纳米管在管径方向的一维电子态波函数充分耦合,进而有效改变了一些前沿分子轨道的波函数在管径两头的分布以及相应的电子布居浓度．基于电子输运的模拟,发现半环葫芦脲分子在碳纳米管一维方向滑动时的某个电压下的电导变化可准确反映电子态波函数在相应分子导电通道上的一维分布信息．     

Fluorescence spectroscopy of single-walled carbon nanotubes in aqueous suspension

Optical studies of single-walled carbon nanotubes have advanced greatly through the recent discovery of near-infrared band gap photoluminescence from single-walled carbon nanotubes (SWNT) isolated in aqueous surfactant suspensions. This fluorescence emission has enabled the detection of many distinct optical transitions and their assignment to specific (n,m) semiconducting species of SWNT. The resulting set of precise transition energies presents a challenge to current theoretical models of nanotube electronic structure and a guide to nanotube researchers using resonance Raman spectroscopy. In the near future, structure-resolved fluorimetry should prove useful for revealing the quantitative (n,m) composition of mixed SWNT samples through sensitive, rapid, and nondestructive measurements. It will also permit detailed studies of many physical and chemical processes that vary with nanotube structure. PACS 71.35.Cc; 78.67.Ch; 78.67.-n     

钯金属吸附对半导体性碳纳米管电输运的影响

利用物理蒸发技术,在半导体性的碳纳米管上沉积钯金属,利用导电原子力显微镜检测钯吸附对碳纳米管电输运的影响.结果表明:沉积的钯在碳纳米管上形成纳米颗粒,随着钯颗粒密度的增加,半导体性碳纳米管逐渐向金属性转变.利用第一性原理计算了吸附有钯原子的半导体性单壁碳纳米管的能带结构.研究发现,钯的覆盖率越高,其禁带宽度越窄,直至为零,定性说明了实验结果的合理性. 关键词： 单壁碳纳米管 钯纳米颗粒 导电原子力显微镜 第一性原理计算     

Dependence of in—tube doping on the radius and helicity of single—wall carbon nanotubes

Using the Lennard－Jones interaction potential between the impurity atom and carbon atom, we have studied the dependence of in-tube impurity doping on the radius of a single-wall carbon nanotube (SWNT), as well as its helicity. The obtained results show that the radius of the most stably doped SWNT is different for different kinds of impurity atoms. This is useful for producing the required doped SWNT. In addition, it is found that the helicity of tube has a strong effect on the potential energy of the atoms doped in the SWNT.     

Transport properties of poly(GACT)-poly(CTGA) deoxyribonucleic acid: A ladder model approach

In this paper, based on the tight-binding Hamiltonian model and within the framework of a generalized Green’s function technique, the electronic conduction through the poly(GACT)-poly(CTGA) DNA molecule in SWNT/DNA/SWNT structure has been numerically investigated. In a ladder model, we consider DNA as a planar molecule containing M cells and four further sites (two base pair sites and two backbone sites) in each cell, sandwiched between two semi-infinite single-walled carbon nanotubes (SWNT) as the electrodes. Having relied on Landauer formalism, we focussed on studying the current-voltage characteristics of DNA, the effect of the coupling strength of SWNT/DNA interface and the role of tube radius of nanotube contacts on the electronic transmission through the foregoing structure. Finally, a characteristic time was calculated for the electron transmission, which measures the delay caused by the tunnelling through the SWNT/DNA interface. The results clearly show that the calculated characteristic time and also the conductance of the system are sensitive to the coupling strength between DNA molecule and nanotube contacts.     

Determination of band gaps of self-assembled carbon nanotube films using Tauc/Davis–Mott model

The band gaps of self-assembled single-walled carbon nanotube (SWNT) films have been determined through curve fitting using the semi-empirical Tauc and Davis–Mott model, based on the measurement of optical absorption at the visible and near infrared range. This study provides a practicable option for the determination of band gaps for ultra-thin SWNT films or multi-walled carbon nanotube films whose vHs peaks cannot be well resolved in absorption spectra.     

MD investigation of the collective carbon atom behavior of a (17, 0) zigzag single wall carbon nanotube under axial tensile strain

The collective dynamic behavior of carbon atoms of a (17, 0) zigzag single wall carbon nanotube is investigated under tensile strains by molecular dynamics (MD) simulations. The “slip vector” parameter is used to study the collective motion of a group of atoms and the deformation behavior in three different directions (axial, radial, and tangential) of a (17, 0) carbon nanotube. The variations of radial slip vectors indicate almost all carbon atoms of the (17, 0) carbon nanotube will stay on the cylindrical surface before the yielding of the single wall carbon nanotube (SWNT). Furthermore, the tangential vectors show kinking deformation for the (17, 0) zigzag tube only rarely appears when the crack occurs. Non-symmetrical deformation around a carbon atom along the axial direction also can be found. The variations in the slip vector values of each atom display a symmetrical crack along the horizontal direction and normal to the tube axis. Chain-like structures with 3–4 atoms can be observed, with the number of chain-like structures decreasing before the breakage of the SWNT. The mechanical properties and dynamic behavior of a (17, 0) zigzag SWNT under tensile strain are also compared with that of a (10, 10) armchair tube in our previous study (Weng et al. 2009).     

Combined Raman scattering and ab initio investigation of the interaction between pyrene and carbon SWNT

Raman spectra of HiPco SWNT and SWNT-pyrene films were measured in the 160–1800 cm^?1 range. Due to the non-covalent interaction between SWNT and pyrene the most intensive component of the SWNT G mode (1590 cm^?1) is downshifted by 2 cm^?1 and becomes narrower. Also the intensity of the low-frequency component of the G mode (1550 cm^?1) decreases by about 30%. Structures and interaction energies in the complexes of pyrene and zigzag (n, 0) SWNTs [6 ≤ n ≤ 20] were determined at the MP2 level of theory. The BSSE-free geometry optimization of the pyrene-zigzag (12,0) SWNT complex converged to a structure with a 1/2staggered conformation and with an intermolecular distance of 3.5 Å. The BSSE-free interaction energy in the complex is ?30.8 kj mol^?1. Increasing of the nanotube diameter leads to a higher interaction energy. This energy becomes equal to ?37.2 kJ mol^?1 in the case of a planar carbon surface.     

Demetalization of single-walled carbon nanotube thin films with microwave irradiation

The microwave irradiation effects on purified HiPCO and CoMoCat single-walled carbon nanotube (SWNT) thin films are investigated. The surface conductivities of the SWNT films are extracted from the measured THz transmission coefficients to provide a direct indication of the metallic content in the films. The observed drastic conductivity decrease indicates a significant metallic content reduction after the microwave irradiation. Two different laser excitations are applied for Raman spectroscopy to reveal the response of different nanotube species. The Raman spectra of both HiPCO and CoMoCat thin films confirm the decrease of metallic carbon nanotubes. The observed microwave-induced effects may potentially lead to a convenient scheme for demetalization of single-walled carbon nanotube mixtures.     

Measuring the thermal conductivity of a single carbon nanotube

Although the thermal properties of millimeter-sized carbon nanotube mats and packed carbon nanofibers have been readily measured, measurements for a single nanotube are extremely difficult. Here, we report a novel method that can reliably measure the thermal conductivity of a single carbon nanotube using a suspended sample-attached T-type nanosensor. Our experimental results show that the thermal conductivity of a carbon nanotube at room temperature increases as its diameter decreases, and exceeds 2000 W/mK for a diameter of 9.8 nm. The temperature dependence of the thermal conductivity for a carbon nanotube with a diameter of 16.1 nm appears to have an asymptote near 320 K. The present method is, in principle, applicable to any kind of a single nanofiber, nanowire, and even single-walled carbon nanotube.     

Novel single-walled carbon nanotubes periodically embedded with four- and eight-membered rings

Based on experimental results, we obtain five types of single-walled carbon nanotube (SWNT) clusters with different chirality indices and diameters using density functional theory (DFT). We then obtain the corresponding SWNTs by using periodic boundary conditions. Studies of the stability and electronic properties show that the stability of the novel SWNTs is independent of the chirality index and relates only to the tube diameter; larger diameters correspond to more stable SWNTs. The electronic properties all show metallic characteristics independent of the chirality indices and tube diameters, thereby promoting the application of metallic-type SWNTs.