球状泡群内气泡的耦合振动

振动气泡形成辐射场影响其他气泡的运动, 故多气泡体系中气泡处于耦合振动状态. 本文在气泡群振动模型的基础上, 考虑气泡间耦合振动的影响, 得到了均匀球状泡群内振动气泡的动力学方程, 以此为基础分析了气泡的非线性声响应特征. 气泡间的耦合振动增加了系统对每个气泡的约束, 降低了气泡的自然共振频率, 增强了气泡的非线性声响应. 随着气泡数密度的增加, 振动气泡受到的抑制增强; 增加液体静压力同样可抑制泡群内气泡的振动, 且存在静压力敏感区(1–2 atm, 1 atm=1.01325×10⁵ Pa); 驱动声波对气泡振动影响很大, 随着声波频率的增加, 能够形成空化影响的气泡尺度范围变窄. 在同样的声条件、泡群尺寸以及气泡内外环境下, 初始半径小于5 μm 的气泡具有较强的声响应. 气泡耦合振动会削弱单个气泡的空化影响, 但可延长多气泡系统空化泡崩溃发生的时间间隔和增大作用范围, 整体空化效应增强.     

双泡耦合声空化动力学过程模拟

为了对双泡耦合的声空化过程进行模拟,本文从流体动力学控制方程和流体体积分数模型出发,在Fluent软件中构建双泡耦合超声空化三维有限元仿真模型,对超声波驱动下流体中双泡耦合声空化动力学过程进行数值模拟,并通过对空化气泡周围声场的变化进行分析研究双泡耦合声空化的非线性动力学特性.结果显示:在超声波驱动下,球形气泡先缓慢扩张,扩张到最大半径后迅速收缩直至溃灭;耦合双气泡间存在相互作用力,使得空化气泡的扩张受到抑制、气泡收缩时间增长;空化气泡在收缩阶段的能量转换能力增强,相比单气泡声空化,耦合双气泡溃灭时气泡内部的压强更大.本文分析结果将为超声空化泡群的动力学过程模拟提供参考.     

超声波声孔效应中气泡动力学的研究

在超声快速制取组织细胞病理切片的过程中，发现激励信号对切片制取效果有明显的影响.为了掌握超声激励信号对组织细胞的影响规律，达到快速制取病理切片的最佳状态，从气泡空化模型入手，通过改变激励信号频率、声压、气泡初始半径和液体黏滞系数等参量，研究了声孔效应中气泡动力学激励机制.数值计算表明：空化泡振动随激励声压增强而升高，随液体黏滞系数增强而减弱；一定频率范围内空化泡振动能保持在膨胀、收缩和振荡的稳定空化状态，存在空化泡稳态振动的最佳激励频率；一定初始半径能保证空化泡产生稳定的振动，存在空化泡稳态振动幅度最大的初始半径.实际操作中，在频率、声压、初始半径和黏滞系数综合作用的若干空化阈内，声孔效应使超声快速法制取细胞组织切片获得最佳效果. 关键词： 声孔效应 超声空化 气泡振动 稳态空化域     

声场中水力空化泡的动力学特性

以水为工作介质,考虑了液体黏性、表面张力、可压缩性及湍流作用等情况,对文丘里管反应器中空化泡在声场作用下的动力学行为特性进行了数值研究.分析了超声波频率、声压及喉径比对空化泡运动特性以及空化泡崩溃时所形成泡温以及压力脉冲的影响.结果表明,超声将水力空化泡运动调制成稳态空化,有利于增强空化效果. 关键词： 超声波 水力空化 湍流 气泡动力学     

低频超声空化场中柱状泡群内气泡的声响应

本文在气泡群振动模型的基础上,考虑气泡间耦合振动的影响,得到了均匀柱状泡群内振动气泡的动力学方程,以此为基础分析了低频超声空化场中柱形气泡聚集区内气泡的非线性声响应特征.气泡间的耦合振动增加了系统对每个气泡的约束,降低了气泡的自然频率,增强了气泡的非线性声响应.随着气泡数密度的增加,气泡的自然共振频率降低,受迫振动气泡受到的抑制增强.数值分析结果表明:1)驱动声波频率越低,气泡的初始半径越小,气泡数密度变化对气泡最大半径变化幅度的影响越大;2)气泡振动幅值响应存在不稳定区,不稳定区域分布与气泡初始半径、驱动声波压力幅值、驱动声波频率等因素有关.在低频超声波作用下,对初始半径处在1—10μm之间的空化气泡而言,气泡初始半径越小,气泡最大半径不稳定区分布范围越大,表明小气泡具有更强的非线性特征.因此,气泡初始半径越小,声环境变化对空化泡声响应稳定性影响越显著.     

超声在液体中的非线性传播及反常衰减

本文从广义的Navier-Stokes流体方程出发,考虑到流体介质的黏滞性和存在的热传导,导出了更接近实际流体的三维非线性声波动方程.鉴于声传播所涉及的空间和时间尺度的复杂性和多样性,文中针对一维情形下的非线性波动方程进行了求解和分析.由方程的二级近似解可以看出,声压振幅的衰减遵循几何级数规律,而且驱动声波的频率越高声压的衰减就越快.在满足条件ωb《ρ0c_0~2时,基波的衰减系数与驱动频率的平方及耗散系数的乘积成正比;二次谐波的衰减规律更加复杂,与频率的更高次幂相关.对声衰减系数及声压的分布进行数值计算发现,声压的分布还与初始的声压幅值及频率有关,初始的声压与频率越高衰减得越快.另外,当声压高于液体的空化阈值时,液体中就会出现大量的空化泡,文中模拟了单个空化泡的运动,发现随着声压的增大空化泡的振动越剧烈、空化泡所受的黏滞力变大,随着声波作用时间的增大黏滞力的幅值迅速增大并与驱动声压值同阶,因而空化泡的非线性径向运动引起的声衰减不容忽视.结果表明,驱动声压越高在空化区域附近引起的声衰减越快、输出的声压越低.     

液体薄层中环链状空化泡云结构稳定性分析

为分析超声空化的薄层液体中稳定的环状气泡链结构,本文考虑气泡间次级声辐射影响,得到了表征气泡间相互作用的气泡基本动力学方程以及次Bjerknes力的表达式,数值分析了气泡平衡半径、声波频率和声压对纯液体区可能出现的单气泡所受的次Bjerknes力,发现环形泡链能够吸引液体区内的新生的半径小于2μm的气泡,这可能是一定条件下环形气泡链能够稳定存在的原因.随着驱动声波压力增加,气泡数密度增加,气泡间的耦合作用增强,液体区内的环形泡链结构可能被液体区内出现的大气泡或者气泡团破坏,进而导致环形结构演变成柱状、雾状乃至整个液体区均充满空化泡的情况发生.通过高速摄影机观察了强声场作用下换能器辐射面外侧液体薄层内空化初生至形成空化云团簇的整个过程,在空化云团簇中发现了局部同步崩溃并形成类纯液体薄层的现象,该液体薄层边界随时间振荡持续约4个声周期后被空化云团簇吞没,局部类纯液体区出现的位置具有随机性.实验观察结果和理论预测具有很好的一致性.     

空化场中大气泡对空化泡振动的抑制效应分析

为探究空化场中多气泡之间的相互作用,结合观察到的注入大气泡周围飞舞的小气泡的实验现象,构建了由两个大气泡和一个空化泡组成的三气泡系统,通过考虑气泡间相互作用的时间延迟效应以及大泡的非球形振动,得到修正的气泡动力学方程组,并数值分析了气泡的振动模态、平衡半径、声波压力与频率等参量对小空化气泡的振动行为与所受次级Bjerknes力的影响.结果表明,大气泡的非球形效应主要表现为一种近场效应,对空化泡的振动影响很小,几乎可以忽略不计.大气泡可抑制空化泡的振动,但当大气泡半径接近于共振半径时,空化泡振动幅值曲线出现共振峰,即存在耦合共振响应.大气泡半径越大,对空化泡抑制作用越强,当空化泡处在两个毫米级大气泡附近时抑制更加显著.声波压力与频率不仅直接影响气泡的振动,还影响空化泡与大气泡之间相互作用的强弱,表现为空化泡所受的次级Bjerknes力在特定的大气泡半径范围内变得对气泡尺寸变化较为敏感,即小的大气泡半径变化可能导致明显的力大小变化,且不同驱动频率下,空化泡所受次级Bjerknes力的敏感半径分布区间不同.空化泡受到的次级Bjerknes力在距离较小或者较大时均可能表现为斥力,与实验观察现象...     

考虑水蒸气蒸发和冷凝的球状泡群中泡的动力学特性

为了深入探究空化泡群中气泡的动力学特性,建立了超声驱动下考虑水蒸气的蒸发和冷凝的泡群中泡的动力方程.基于该方程,研究了泡群中泡的位置、泡的数量、泡的初始半径对其动力学特性的影响,探究了超声作用下球状泡群中气泡半径、能量、温度、压力和气泡内水蒸气分子数的变化规律.结果表明:泡群中泡的运动受到周围气泡的抑制作用;泡群中泡的初始半径大小对泡群中泡的半径、能量、温度、压力和气泡内水蒸气分子数有显著影响;泡群中泡的位置距离泡群中心越远,泡的膨胀半径越大;随着泡群中泡的数目增加,泡的振幅减小;超声频率增加,泡群中泡的空化效应减弱;超声声压增加,泡群中泡的空化效应增加.研究结果为超声空化泡群的研究提供了理论参考.     

超声波作用下泡群的共振声响应

从球状泡群气泡动力学方程出发, 考虑泡群间次级声辐射的影响, 得到了声场中两泡群共同存在时气泡振动的动力学方程, 并以此为基础探讨声波驱动下双泡群振动系统的共振响应特征. 由于泡群间气泡间的相互作用, 系统存在低频共振和高频共振现象, 两不同共振频率的数值与泡群内气泡的本征频率相关. 泡群内气泡的本征频率又受到初始半径、泡群大小和泡群内气泡数量的影响. 气泡自由振动和驱动声波的耦合激起泡群内气泡的受迫振动, 气泡初始半径、气泡数密度和驱动声波频率等都会影响泡群内气泡的振动幅值和初相位. 关键词： 气泡群 共振 声响应 超声空化     

Theoretical prediction of the yield of strong oxides under acoustic cavitation

Considering liquid viscosity, surface tension, and liquid compressibility, the effects of dynamical behaviors of cavitation bubbles on temperature and the amount of oxides inside the bubble are numerically investigated by acoustic field,regarding water as a work medium. The effects of acoustic frequency, acoustic pressure amplitude, and driving waveforms on bubble temperature and the number of oxides inside the bubbles by rapid collapse of cavitation bubbles are analysed.The results show that the changes of acoustic frequency, acoustic pressure amplitude, and driving waveforms not only have an effect on temperature and the number of oxides inside the bubble, but also influence the degradation species of pollution,which provides guidance for improving the degradation of water pollution.     

A two-dimensional nonlinear model for the generation of stable cavitation bubbles

Bubbles appear by acoustic cavitation in a liquid when rarefaction pressures attain a specific threshold value in a liquid. Once they are created, the stable cavitation bubbles oscillate nonlinearly and affect the ultrasonic field. Here we present a model developed for the study of bubble generation in a liquid contained in a two-dimensional cavity in which a standing ultrasonic field is established. The model considers dissipation and dispersion due to the bubbles. It also assumes that both the ultrasonic field and the bubble oscillations are nonlinear. The numerical experiments predict where the bubbles are generated from a population of nuclei distributed in the liquid and show how they affect the ultrasonic field.     

Theoretical estimation of sonochemical yield in bubble cluster in acoustic field

In order to learn more about the physical phenomena occurring in cloud cavitation, the nonlinear dynamics of a spherical cluster of cavitation bubbles and cavitation bubbles in cluster in an acoustic field excited by a square pressure wave are numerically investigated by considering viscosity, surface tension, and the weak compressibility of the liquid.The theoretical prediction of the yield of oxidants produced inside bubbles during the strong collapse stage of cavitation bubbles is also investigated. The effects of acoustic frequency, acoustic pressure amplitude, and the number of bubbles in cluster on bubble temperature and the quantity of oxidants produced inside bubbles are analyzed. The results show that the change of acoustic frequency, acoustic pressure amplitude, and the number of bubbles in cluster have an effect not only on temperature and the quantity of oxidants inside the bubble, but also on the degradation types of pollutants, which provides a guidance in improving the sonochemical degradation of organic pollutants.     

Oscillation and Migration of Bubbles within Ultrasonic Field

The oscillation and migration of bubbles within an intensive ultrasonic field are important issues concerning acoustic cavitation in liquids.We establish a selection map of bubble oscillation mode related to initial bubble radius and driving sound pressure under 20 kHz ultrasound and analyze the individual-bubble migration induced by the combined effects of pressure gradient and acoustic streaming.Our results indicate that the pressure threshold of stable and transient cavitation decreases with the increasing initial bubble radius.At the pressure antinode,the Bjerknes force dominates the bubble migration, resulting in the large bubbles gathering toward antinode center,whereas small bubbles escape from antinode.By contrast,at the pressure node,the bubble migration is primarily controlled by acoustic streaming,which effectively weakens the bubble adhesion on the container walls,thereby enhancing the cavitation effect in the whole liquid.     

采用遗传算法对压力脉动过程中气泡模型参数的辨识

流动液体中的压力变化会引起气泡和气穴的产生及破灭,而气泡和气穴又会对液体的流动产生影响及压力变化.为了合理预测流控系统瞬态压力脉动过程中气泡和气穴的体积变化及其对脉动传播过程的影响,基于气泡溶解和析出的物理过程,建立了压力脉动过程中气泡和气穴产生及破灭的数学模型,并提出采用遗传算法对气泡模型中初始气泡体积、气体溶解和析出时间常数进行参数辨识.以一段液压油管路为研究对象,对管路中伴随气泡和气穴的瞬态压力脉动过程进行仿真及实验研究.利用仿真及实验结果,验证了采用遗传算法对气泡模型进行参数辨识的可行性. 关键词： 气泡 气穴 压力脉动 参数辨识     

High-speed imaging of ultrasound driven cavitation bubbles in blind and through holes

The interest in application of ultrasonic cavitation for cleaning and surface treatment processes has increased greatly in the last decades. However, not much is known about the behavior of cavitation bubbles inside the microstructural features of the solid substrates. Here we report on an experimental study on dynamics of acoustically driven (38.5 kHz) cavitation bubbles inside the blind and through holes of PMMA plates by using high-speed imaging. Various diameters of blind (150, 200, 250 and 1000 µm) and through holes (200 and 1000 µm) were investigated. Gas bubbles are usually trapped in the holes during substrate immersion in the liquid thus preventing their complete wetting. We demonstrate that trapped gas can be successfully removed from the holes under ultrasound agitation. Besides the primary Bjerknes force and acoustic streaming, the shape oscillations of the trapped gas bubble seem to be a driving force for bubble removal out of the holes. We further discuss the bubble dynamics inside microholes for water and Cu²⁺ salt solution. It is found that the hole diameter and partly the type of liquid media influences the number, size and dynamics of the cavitation bubbles. The experiments also showed that a large amount of the liquid volume inside the holes can be displaced within one acoustic cycle by the expansion of the cavitation bubbles. This confirmed that ultrasound is a very effective tool to intensify liquid exchange processes, and it might significantly improve micro mixing in small structures. The investigation of the effect of ultrasound power on the bubble density distribution revealed the possibility to control the cavitation bubble distribution inside the microholes. At a high ultrasound power (31.5 W) we observed the highest bubble density at the hole entrances, while reducing the ultrasound power by a factor of ten shifted the bubble locations to the inner end of the blind holes or to the middle of the through holes.     

Dissolved gas and ultrasonic cavitation – A review

The physics and chemistry of nonlinearly oscillating acoustic cavitation bubbles are strongly influenced by the dissolved gas in the surrounding liquid. Changing the gas alters among others the luminescence spectrum, and the radical production of the collapsing bubbles. An overview of experiments with various gas types and concentration described in literature is given and is compared to mechanisms that lead to the observed changes in luminescence spectra and radical production. The dissolved gas type changes the bubble adiabatic ratio, thermal conductivity, and the liquid surface tension, and consequently the hot spot temperature. The gas can also participate in chemical reactions, which can enhance radical production or luminescence of a cavitation bubble. With this knowledge, the gas content in cavitation can be tailored to obtain the desired output.     

A new pressure formulation for gas-compressibility dampening in bubble dynamics models

We formulated a pressure equation for bubbles performing nonlinear radial oscillations under ultrasonic high pressure amplitudes. The proposed equation corrects the gas pressure at the gas–liquid interface on inertial bubbles. This pressure formulation, expressed in terms of gas-Mach number, accounts for dampening due to gas compressibility during the violent collapse of cavitation bubbles and during subsequent rebounds. We refer to this as inhomogeneous pressure, where the gas pressure at the gas–liquid interface can differ to the pressure at the centre of the bubble, in contrast to homogenous pressure formulations that consider that pressure inside the bubble is spatially uniform from the wall to the centre. The pressure correction was applied to two bubble dynamic models: the incompressible Rayleigh–Plesset equation and the compressible Keller and Miksis equation. This improved the predictions of the nonlinear radial motion of the bubble vs time obtained with both models. Those simulations were also compared with other bubble dynamics models that account for liquid and gas compressibility effects. It was found that our corrected models are in closer agreement with experimental data than alternative models. It was concluded that the Rayleigh–Plesset family of equations improve accuracy by using our proposed pressure correction.     

气泡在超声场中绕圈运动的高速摄影及其图像分析

借助高速摄影和图像分析技术对首次发现的附壁气泡的绕圈现象进行了实验研究,重点研究游移气泡的运动轨迹、附壁气泡的布阵过程、气泡的来源以及气泡的振动细节.研究发现游移绕圈气泡的运动轨迹呈现出不稳定、不规则、不光滑的特点.阵列气泡源于游移气泡,而游移气泡变成阵列气泡的方式主要是通过合并增大体积,从而减小所受的Bjerknes力,降低活性的方式实现的.游移气泡源于ALF(acoustic lichtenberg figure)空化云中大量空泡的合并,使以径向振动为主的空泡逐渐过渡到以表面波动为主的气泡.阵列气泡在Bjerknes力的作用下呈现出规则的表面波动,而体积更小受力更大的游移空泡的表面完全失稳,呈现极不规则的形貌,并对附近阵列气泡的表面波动产生影响.阵列气泡呈现出十分规则的排布,相邻阵列气泡之间的振动相位是相反的,表现为相互排斥.