大功率多波长可转换双包层光纤激光器

在多模掺镱双包层光纤上,利用相位掩模法直接写制Bragg光栅作为激光器后腔镜,得到多波长激光输出.在室温下,通过调节偏振控制器可以得到稳定的单波长及多波长的激光输出,输出波长范围在1 056～1 061 nm,线宽均小于0.02 nm.在25 W的976 nm激光泵浦下,激光器得到功率为6 W的多波长输出.     

基于Sagnac环形镜的高功率多波长线偏振掺镱光纤激光器

设计了基于Sagnac环形镜的哑铃型结构全光纤掺镱激光器,使用976 nm多模激光二极管泵浦,通过调节偏振控制器获得了稳定的多波长线偏振激光输出。泵浦功率为20.4 W时,最高输出功率达到5.13 W,功率波动不大于0.02 W,激光器输出多波长激光线偏振度约为14.19 dB,多波长输出功率平坦度优于3 dB。     

国产全光纤结构激光器实现245 W高功率激光输出

 以国产掺镱光纤为增益介质,利用国产泵浦源和光纤器件,构建了主振荡功率放大（MOPA）结构的全国产大功率全光纤激光器。激光器包括10 W种子激光器和高功率放大器两部分。在注入最大泵浦功率为356 W时,获得了245 W波长1 080 nm激光的稳定输出,光-光效率为69%。激光器单次连续出光时间约30 min,功率稳定性在1%以内。目前激光器输出功率受限于泵浦功率,增加泵浦源的数目有望进一步提高输出功率。     

基于M型掺镱光纤的近单模2 kW光纤放大器

模式不稳定效应和非线性效应已经成为高功率光纤激光器中限制输出功率和光束质量进一步提升的主要障碍.采用改进的化学气相沉积工艺结合溶液掺杂技术制备25/400μm的M型掺镱双包层光纤,纤芯和中间凹陷区域的数值孔径分别为0.054和0.025.基于该光纤搭建976 nm双向泵浦全光纤结构放大器.在泵浦光功率为3283 W时,获得2285 W中心波长为1080 nm的激光输出,3 dB线宽为3.01 nm,测量的光束质量因子为1.42,且未出现受激拉曼散射现象.这是目前基于M型掺镱光纤实现的最高输出功率,通过优化光纤结构参数实现功率进一步提升是有希望的.     

全光纤结构高功率主振荡功率放大型单频光纤激光器

研制了一台全光纤结构主振荡功率放大型掺镱单频光纤激光器。该光纤激光器包括种子激光器和级联放大器两部分。种子激光器是自行搭建的环形腔结构的单频窄线宽光纤激光器。在976 nm半导体激光器泵浦下,能够输出线宽为10 MHz量级、波长为1 079.88 nm的单频光,激光功率为10.02 W,光-光转化效率为58.9%,斜率效率为65.3%。     

100 W全光纤声光调Q光纤激光器实验研究

 报道了一台全光纤结构主振荡功率放大(MOPA)型掺镱脉冲光纤激光器,以光纤光栅为腔镜,光纤型声光调Q的光纤激光器为种子源,通过两级掺镱双包层光纤放大器实现功率放大。对声光调Q的光纤激光器输出特性进行了研究,比较了不同泵浦波长、不同重复频率对激光输出功率和脉冲宽度的影响,并实现了最短脉冲宽度25 ns、单脉冲能量45 μJ的脉冲激光输出。在重复频率50 kHz时,对脉冲宽度130 ns、平均功率0.6 W的种子光进行放大,得到了平均功率102.5 W、脉冲宽度约240 ns的激光输出。     

布里渊-掺铒光纤随机光纤激光器输出特性分析

设计了一种基于受激布里渊散射和掺铒光纤混合增益的随机光纤激光器,该激光器选用两段长为20km的单模光纤组成全开放腔结构,利用单模光纤的瑞利散射提供随机光反馈.研究表明,固定布里渊泵浦波长和泵浦功率分别为1 550.00nm和2.19mW时,增加掺铒光纤泵浦功率,可以实现两个波长的随机激光输出,一阶和二阶受激布里渊散射光与布里渊泵浦光波长间隔分别约为0.088nm和0.174nm,产生一阶和二阶受激布里渊散射对应的掺铒光纤泵浦功率分别为190mW和370mW;当掺铒光纤泵浦功率为433mW时,激光器两端的最大输出功率为1.60mW和1.68mW.当掺铒光纤泵浦功率明显高于阈值功率时,获得的一阶和二阶随机激光输出稳定,3dB线宽约为0.022nm,峰值强度和位置基本不随时间而变化.     

辅腔泵浦高功率铒镱共掺光纤激光器实验研究

铒镱共掺光纤激光器的功率提高主要受热效应和镱波段放大的自发辐射的限制。为了提高铒镱共掺光纤激光器的输出功率,设计了液冷散热结构并采用辅腔泵浦法进行实验研究。结果表明,采用2.1 m长的大模面积铒镱共掺双包层光纤时,在47.5 W的泵浦功率下得到了波长为1 548.9 nm、最高功率为21.6 W的输出,综合泵浦转化效率为45.7%;辅助腔中镱波段振荡建立前后的斜率效率分别为48.4%和56.2%。     

1137 nm长波掺镱光纤激光器的出光实验

分别使用976 nm半导体激光器和1040 nm光纤激光器作为泵浦源,实现了1137 nm长波光纤激光器的出光,输出功率均超过百mW。激光器采用相同的线性腔结构,高反光栅和低反光栅的反射率分别为99.6%和39.7%,增益介质是一段8 m长的掺镱光纤,纤芯直径5 m。当976 nm半导体泵浦功率为912 mW时,1137 nm激光输出功率为182 mW,对应的斜率效率为28.5%;当1040 nm激光功率为1.59 W时,输出的1137 nm激光功率为278 mW,斜率效率约为25%。在此基础上对两种泵浦方式进行了对比分析。     

端面泵浦掺Yb3+双包层光纤激光器

从双包层光纤激光器的速率方程出发，得到了光纤中泵浦光与激光的功率分布、输出功率与泵浦功率的关系、腔镜反射率及光纤长度对输出功率的影响。研究结果表明：输出激光功率与光纤长度及后腔镜反射率有很强的依赖关系，存在一个输出功率最大的最佳光纤长度。后腔镜反射率越大，输出激光功率越小；当光纤长度较短时，在输出端放置反射镜使泵浦光高反射，可以提高输出功率和效率。通过对端面泵浦掺Yb3+双包层光纤激光器进行理论分析和实验研究，得到输出激光的中心波长为1088.3nm，斜率效率为33.7%，最大输出功率为1.75W。     

All-fiber single polarized Yb-doped fiber laser with a high extinction ratio

We present an all-fiber design for a single polarization Yb-doped fiber laser with all-fiber connections spliced. Single polarization with a high extinction ratio was achieved by the design of a laser cavity consisting of a fiber Bragg grating inscribed on a single-polarization fiber as a high reflective mirror and a piece of end-cleaved single-polarization fiber as an output coupler. The fiber laser operates at 1063.25 nm with an output power of 1.7 W, an optical signal- to-noise ratio of 70 dB and a narrow bandwidth of 54 pm. The laser output has a polarization extinction ratio of 700:1 or 28 dB, and a very stable power output.     

980-nm all-fiber mode-locked Yb-doped phosphate fiber oscillator based on semiconductor saturable absorber mirror and its amplifier

A 980-nm semiconductor saturable absorber mirror(SESAM) mode-locked Yb-doped phosphate fiber laser is demonstrated by using an all-fiber linear cavity configuration. Two different kinds of cavity lengths are introduced into the oscillator to obtain a robust and stable mode-locked seed source. When the cavity length is chosen to be 6 m, the oscillator generates an average output power of 3.5 m W and a pulse width of 76.27 ps with a repetition rate of 17.08 MHz. As the cavity length is optimized to short, 4.4-m W maximum output power and 61.15-ps pulse width are produced at a repetition rate of 20.96 MHz. The output spectrum is centered at 980 nm with a narrow spectral bandwidth of 0.13 nm. In the experiment, no undesired amplified spontaneous emission(ASE) nor harmful oscillation around 1030 nm is observed. Moreover,through a two-stage all-fiber-integrated amplifier, an output power of 740 m W is generated with a pulse width of 200 ps.     

主振荡功率放大结构窄线宽全光纤激光器334 W高功率输出

 搭建了一台全光纤结构的窄线宽高功率掺镱光纤激光器。种子激光的输出功率大于40 mW,线宽窄于100 MHz。采用主振荡功率放大结构三级放大,主放泵浦功率为405 W时得到了334 W的窄线宽高功率激光输出,光光转换效率为82.4%。目前,激光器输出功率仅受限于泵浦功率,增加有效泵浦功率即有望进一步提高输出功率。     

1018 nm短波长掺镱光纤激光高功率自组织相干合成

搭建了两台高功率、低量子损耗的1018 nm短波长掺镱光纤激光器,进行了全光纤结构下两路光纤激光器的相干合成实验。获得了功率为55 W、合成效率为90.2%的相干输出,这是当前严格单模1018 nm光纤激光器的最高功率水平。同时,验证了Michelson腔自组织相干合成技术能够实现光纤激光器的高功率单模输出。     

窄线宽光纤激光器在1030 nm波段实现3 kW近衍射极限输出

基于大模场面积掺镱光纤搭建了全光纤1030 nm高功率窄线宽光纤激光主振荡功率放大系统,实现了3004 W的最高功率输出,斜率效率69.27%,是目前报道的输出功率最高的1030 nm波段近衍射极限光纤激光器。最高输出功率时,x,y方向的光束质量因子分别为1.169,1.174,3 dB光谱宽度为0.18 nm,放大自发辐射抑制比达到37 dB。     

Output Characteristics of High-Power Continuous Wave Raman Fiber Laser at 1239 nm Using Phosphosilicate Fiber

A high-power singlemode Raman fiber laser (RFL) with maximum output power of 4.11 W and maximum power conversion efficiency of 47.40% at 1239 nm is realized using continuous wave 8.4 W Yb-doped double-clad fiber laser as a pump, 700 m phosphosilicate fiber, and a Raman cavity formed by a pair of fiber Bragg grating mirrors at 1239 nm. The output characteristics of the RFL at 1239 nm for different fiber lengths and output mirror reflectance are reported. Theoretical simulation is done to numerically optimize for fiber length and output coupler reflectivity to obtain maximum first Stokes power.     

1150 nm High-Power Fiber Laser Oscillator Pumped by 976 nm Laser Diode

We present an all-fiber 1150 nm Yb-doped fiber laser oscillator pumped by a 976 nm laser diode. To suppress amplified spontaneous emission and avoid parasitic laser oscillation, we propose a long-length gain fiber and a high-reflectivity output fiber Bragg grating in the fiber laser oscillator. The 1150 nm band single-mode fiber laser with output power of 20.5 W is demonstrated at room temperature. The optical-to-optical conversion efficiency ranges up to 51.6% at the maximum output. The central wavelength of the fiber laser oscillator is 1150.35 nm, and its 3 dB spectral width is 0.72 nm. No evidence of amplified spontaneous emission, residual pump light, or parasitic laser oscillation were observed in the experiments. The high-power 1150 nm fiber laser oscillator can be used as a pump source in the development of a 3 μm Ho-doped fiber laser.     

307 W high-power 1018 nm monolithic tandem pump fiber source with effective thermal management

We report a 307 W 1018 nm Yb-doped fiber laser pumped by a single 976 nm laser diode. The cavity slope efficiency is up to 75.9% and the amplified spontaneous emission is suppressed by 54 dB. The beam quality of the output laser has an M2 factor of 1.17. Effective thermal management is considered to ensure the stable operation of our system. The power stability at the maximum output power level is measured during a period of0.5 h and the power fluctuation is less than 0.8%. This architecture can be an effective high brightness pump source of core-pumping high-power fiber amplifiers.