Creep of polymer concrete in the nonlinear region

Two polyester-based polymer concretes with various volume content of diabase as an extender and aggregate are tested in creep under compression at different stress levels. The phenomenological and structural approaches are both used to analyze the experimental data. Common features of changes in the instantaneous and creep compliances are clarified, and a phenomenological creep model which accounts for the changes in the instantaneous compliance and in the retardation spectrum depending on the stress level is developed. It is shown that the model can be used to describe the experimental results of stress relaxation and creep under repeated loading. Modeling of the composite structure and subsequent solution of the optimization problem confirm the possibility of the existence of an interphase layer more compliant than the binder. A direct correlation between the interphase volume content and the instantaneous compliance of the composite is revealed. It is found that the distinction in nonlinearity of the viscoelastic behavior of the two polymer concretes under investigation can be due to the difference in their porosity. Submitted to the 11th International Conference on Mechanics of Composite Materials (Riga, June 11–15, 2000.) Translated from Mekhanika Kompozitnykh Materialov, Vol. 36, No. 2, pp. 147–164, 2000.     

A model for predicting the shear bearing capacity of FRP-strengthened beams

The shear failure of reinforced concrete beams needs more attention than the bending failure since no or only small warning precedes the failure. For this reason, it is of utmost importance to understand the shear bearing capacity and also to be able to undertake significant rehabilitation work if necessary. In this paper, a design model for the shear strengthening of concrete beams by using fiber-reinforced polymers (FRP) is presented, and the limitations of the truss model analogy are highlighted. The fracture mechanics approach is used in analyzing the bond behavior between the FRP composites and concrete. The fracture energy of concrete and the axial rigidity of the FRP are considered to be the most important parameters. The effective strain in the FRP when the debonding occurs is determined. The limitations of the anchorage length over the cross section are analyzed. A simple iterative design method for the shear debonding is finally proposed. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 44, No. 3, pp. 357–372, May–June, 2008.     

Gaussian Versus Optimal Integration of Analytic Functions

We consider error estimates for optimal and Gaussian quadrature formulas if the integrand is analytic and bounded in a certain complex region. First, a simple technique for the derivation of lower bounds for the optimal error constants is presented. This method is applied to Szeg?-type weight functions and ellipses as regions of analyticity. In this situation, the error constants for the Gaussian formulas are close to the obtained lower bounds, which proves the quality of the Gaussian formulas and also of the lower bounds. In the sequel, different regions of analyticity are investigated. It turns out that almost exclusively for ellipses, the Gaussian formulas are near-optimal. For classes of simply connected regions of analyticity, which are additionally symmetric to the real axis, the asymptotic of the worst ratio between the error constants of the Gaussian formulas and the optimal error constants is calculated. As a by-product, we prove explicit lower bounds for the Christoffel-function for the constant weight function and arguments outside the interval of integration. September 7, 1995. Date revised: October 25, 1996.     

A necessary and sufficient condition for the existence of an exponential attractor

We give a necessary and sufficient condition for the existence of an exponential attractor. The condition is formulated in the context of metric spaces. It also captures the quantitative properties of the attractor, i.e., the dimension and the rate of attraction. As an application, we show that the evolution operator for the wave equation with nonlinear damping has an exponential attractor.     

Dynamical Spin Susceptibility in the t–J Model in the Superconducting Phase

Dynamical spin susceptibility is calculated for the t–J model in the superconducting phase using the memory function method in terms of the Hubbard operators. The self-consistent system of equations for the memory function is obtained within the mode-coupling approximation. Both itinerant hole excitations and localized spin fluctuations contribute to the memory function. Moreover, the itinerant contribution itself consists of two parts, i.e., the contribution of Bogoliubov quasiparticles and that of Cooper pairs. The spin dynamics is diffusive in the hydrodynamic limit, but the itinerant part does not contribute to the spin diffusion. In the high frequency region, spin–wave-like excitations continue to exist. We discuss our analytic results in the light of neutron scattering experiments performed on the cuprate superconductors.     

Variation of the structure and permeability of tensioned fiber layers during impregnation with a thermoplastic polymer melt

The influence of displacements of tensioned fibers on the impregnation of fibrous layers with a polymer melt and on the final composite structure is studied. Using computer simulation, it is shown that, during impregnation, the structure of tensioned fibrous layers changes considerably depending on the initial arrangement and tensioning of fibers. The consolidated regions formed under the melt front move inside the impregnated layer with the advancing melt front. Displacement of the tensioned fibers as well as the formation of “washouts” favors the impregnation of internal layers, but cause significant inhomogeneity of the polymer structure. The surface (on the side of the melt flow) regions are more saturated with the polymer than the internal ones. A difference in the melt percolation mechanisms at various impregnation regimes is revealed. The effective permeability coefficients of a tensioned fiber layer are not constant but depend on the conditions and regimes of impregnation. Submitted to the 11th Conference on the Mechanics of Composite Materials (Riga, June 11–15, 2000). Translated from Mekhanika Kompozitnykh Materialov, Vol. 36, No. 2, pp. 259–270, March–April, 2000.     

Multi‐dimensional Lotka–Volterra systems for carcinogenesis mutations

In the paper we consider three classes of models describing carcinogenesis mutations. Every considered model is described by the system of (n+1) equations, and in each class three models are studied: the first is expressed as a system of ordinary differential equations (ODEs), the second—as a system of reaction–diffusion equations (RDEs) with the same kinetics as the first one and with the Neumann boundary conditions, while the third is also described by the system of RDEs but with the Dirichlet boundary conditions. The models are formulated on the basis of the Lotka–Volterra systems (food chains and competition systems) and in the case of RDEs the linear diffusion is considered. The differences between studied classes of models are expressed by the kinetic functions, namely by the form of kinetic function for the last variable, which reflects the dynamics of malignant cells (that is the last stage of mutations). In the first class the models are described by the typical food chain with favourable unbounded environment for the last stage, in the second one—the last equation expresses competition between the pre‐malignant and malignant cells and the environment is also unbounded, while for the third one—it is expressed by predation term but the environment is unfavourable. The properties of the systems in each class are studied and compared. It occurs that the behaviour of solutions to the systems of ODEs and RDEs with the Neumann boundary conditions is similar in each class; i.e. it does not depend on diffusion coefficients, but strongly depends on the class of models. On the other hand, in the case of the Dirichlet boundary conditions this behaviour is related to the magnitude of diffusion coefficients. For sufficiently large diffusion coefficients it is similar independently of the class of models, i.e. the trivial solution that is unstable for zero diffusion gains stability. Copyright © 2009 John Wiley & Sons, Ltd.     

Forces of rails for electromagnetic railguns

In this paper, using electromagnetic theory, the equations for the total magnetic force on the rails are deduced. Besides this, the equations for the changes of the magnetic force along with time and the running position of the armature under jointed pulse operating current are presented. Then, the equations for changes of the bending stress and shear stress in the rail along with time and the running position of the armature are given. Changes of the magnetic force distribution between the two rails along with the running position of the armature and other parameters are investigated. The total electromagnetic forces on the rail under jointed pulse operating current are analyzed. Distribution and changes of the bending stresses in the rail are studied. A number of results are obtained. The results are useful for design and application of the railgun system.     

Worst-case robust Omega ratio

The Omega ratio is a recent performance measure proposed to overcome the known shortcomings of the Sharpe ratio. Until recently, the Omega ratio was thought to be computationally intractable, and research was focused on heuristic optimization procedures. We have shown elsewhere that the Omega ratio optimization is equivalent to a linear program and hence can be solved exactly in polynomial time. This permits the investigation of more complex and realistic variants of the problem. The standard formulation of the Omega ratio requires perfect information for the probability distribution of the asset returns. In this paper, we investigate the problem arising from the probability distribution of the asset returns being only partially known. We introduce the robust variant of the conventional Omega ratio that hedges against uncertainty in the probability distribution. We examine the worst-case Omega ratio optimization problem under three types of uncertainty – mixture distribution, box and ellipsoidal uncertainty – and show that the problem remains tractable.     

Piecewise parametric polynomial fuzzy sets

We present a scheme for tractable parametric representation of fuzzy set membership functions based on the use of a recursive monotonic hierarchy that yields different polynomial functions with different orders. Polynomials of the first order were found to be simple bivalent sets, while the second order polynomials represent the typical saw shape triangles. Higher order polynomials present more diverse membership shapes. The approach demonstrates an enhanced method to manage and fit the profile of membership functions through the access to the polynomials order, the number and the multiplicity of anchor points as wells as the uniformity and periodicity features used in the approach. These parameters provide an interesting means to assist in fitting a fuzzy controller according to system requirements. Besides, the polynomial fuzzy sets have tractable characteristics concerning the continuity and differentiability that depend on the order of the polynomials. Higher order polynomials can be differentiated as many times as the order of the polynomial less the multiplicity of the anchor points. An algorithmic optimization approach using the steepest descent method is introduced for fuzzy controller tuning. It was shown that the controller can be optimized to model a certain output within small number of iterations and very small error margins. The mathematics generated by the approach is consistent and can be simply generalized to standard applications. The recursive propagation was noticed for its clarity and ease of calculations. Further, the degree of association between the sets is not limited to the neighbors as in traditional applications; instead, it may extend beyond.Such approach can be useful in dynamic fuzzy sets for adaptive modeling in view of the fact that the shape parameters can be easily altered to get different profiles while keeping the math unchanged. Hypothetically, any shape of membership functions under the partition of unity constraint can be produced. The significance of the mentioned characteristics of such modeling can be observed in the field of combinatorial and continuous parameter optimization, automated tuning, optimal fuzzy control, fuzzy-neural control, membership function fitting, adaptive modeling, and many other fields that require customized as well as standard fuzzy membership functions. Experimental work of different scenarios with diverse fuzzy rules and polynomial sets has been conducted to verify and validate our results.     

A perturbed risk model with dependence between premium rates and claim sizes

This paper considers a dependent risk model with diffusion for the surplus of an insurer, in which a current premium rate will be adjusted after a claim occurs and the adjusted rate is determined by the amount of the claim. At the same time, the diffusion is changed correspondingly. Using Rouché’s theorem, we first derive the closed-form solution for the Laplace transform of the survival probability in the dependent risk model. Then, using the Laplace transform, we derive a defective renewal equation satisfied by the survival probability. For the exponential claim sizes, we present the explicit recursion expression for the survival probability, by which we can exactly solve the survival probability step-by-step. We also illustrate the influence of the model parameters in the dependent risk model on the survival probability by numerical examples.     

The distributional dimension of fractals

In the book [1] H.Triebel introduces the distributional dimension of fractals in an analytical form and proves that： for Г as a non-empty set in R^n with Lebesgue measure ｜Г｜ = 0, one has dimH Г = dimD Г, where dimD Г and dimH Г are the Hausdorff dimension and distributional dimension, respectively. Thus we might say that the distributional dimension is an analytical definition for Hausdorff dimension. Therefore we can study Hausdorff dimension through the distributional dimension analytically. By discussing the distributional dimension, this paper intends to set up a criterion for estimating the upper and lower bounds of Hausdorff dimension analytically. Examples illustrating the criterion are included in the end.     

多约束的多阶段积极投资组合模型及实证研究

构建投资组合时需要衡量其风险, 除了考虑组合本身的风险暴露, 还需考虑其相对基准组合的风险暴露. 再者, 确定组合权重时需要根据市场的规则加入合适的约束. 基于此, 为了较为完整地考虑现实投资组合面临的风险及交易约束, 将绝对风险(CVaR)和相对风险(跟踪误差)作为风险约束, 将交易成本、卖空限制和多元权值作为交易限制约束, 构建一个新的多阶段投资组合模型, 并利用动态规划和非线性优化方法进行求解. 最后, 利用上证50成分股中41只股票构建投资组合进行实证研究. 实证结果表明构建的多阶段投资组合模型能持续战胜基准组合且优于单阶段投资组合, 同时也表明模型考虑多元权值约束具有现实意义.     

Structural properties of the one-dimensional drift-diffusion models for semiconductors

This paper is devoted to the analysis of the one-dimensional current and voltage drift-diffusion models for arbitrary types of semiconductor devices and under the assumption of vanishing generation recombination. We show in the course of this paper, that these models satisfy structural properties, which are due to the particular form of the coupling of the involved systems. These structural properties allow us to prove an existence and uniqueness result for the solutions of the current driven model together with monotonicity properties with respect to the total current , of the electron and hole current densities and of the electric field at the contacts. We also prove analytic dependence of the solutions on . These results allow us to establish several qualitative properties of the current voltage characteristic. In particular, we give the nature of the (possible) bifurcation points of this curve, we show that the voltage function is an analytic function of the total current and we characterize the asymptotic behavior of the currents for large voltages. As a consequence, we show that the currents never saturate as the voltage goes to , contrary to what was predicted by numerical simulations by M. S. Mock (Compel. 1 (1982), pp. 165--174). We also analyze the drift-diffusion models under the assumption of quasi-neutral approximation. We show, in particular, that the reduced current driven model has at most one solution, but that it does not always have a solution. Then, we compare the full and the reduced voltage driven models and we show that, in general, the quasi-neutral approximation is not accurate for large voltages, even if no saturation phenomenon occurs. Finally, we prove a local existence and uniqueness result for the current driven model in the case of small generation recombination terms.

     

Investigation of the Stress State of Pressure Vessels of Inhomogeneous Structure Made of Composite Materials

The problem on the stress-strain state of layered cylindrical shells with bottoms of intricate shape under the action of internal pressure is considered. The elastic system examined is formed by spiral-circular winding. Two variants of the shell bottom structure are investigated. In the first variant, one spiral layer is installed, which leads to great variations in the bottom thickness along the meridian. In the second one, the bottoms are formed according to the zone-winding scheme. The stress state of the shell constructions of the classes considered is determined by solving boundary-value problems for systems of ordinary differential equations. The solution results for cylindrical shells with elliptic bottoms for the two types of winding are given. It is shown that the zone winding leads to smaller deflections and stresses than the conventional ways of reinforcing shell bottoms.     

Modelling and simulation of micro-well formation

Physico-chemical processes on the micro-scale require new modelling concepts because some effects become dominating that are negligible for macroscopic systems. This is illustrated by a new method for the production of micro-wells based on the placement of a small drop of toluene on a plate of polystyrene. After droplet evaporation, a micro-well is left. A mathematical model has been developed to understand the elementary processes of the micro-well formation. The model accounts for: (1) growth of the drop on the substrate, (2) evaporation process of the solvent, (3) dissolution of the substrate, (4) flow rate in the evaporating drop caused by the pinning effect, including the vertical velocity profile, and (5) increase in the concentration of dissolved material followed by precipitation. In the modelling and simulation process, it could be shown that the method of drop production also has a significant influence on the shape of the micro-wells.     

The Cauchy problem for ut=Δu+|∇u|

With q a positive real number, the nonlinear partial differential equation in the title of the paper arises in the study of the growth of surfaces. In that context it is known as the generalized deterministic KPZ equation. The paper is concerned with the initial-value problem for the equation under the assumption that the initial-data function is bounded and continuous. Results on the existence, uniqueness, and regularity of solutions are obtained.     

面向远海岛屿的救助基地选址优化模型及其算法

为解决在远海海域选择岛屿建设救助基地的方案优化问题,建立了基于GIS和智能算法的双目标优化模型,采用自适应拉伸的拥挤距离计算公式,设计了自适应精英保留策略对算法进行改进,通过剖析决策者选择最优方案的基本原则,得到了性价比最高的优化方案。最后,以我国南海南沙群岛选择岛屿建设救助基地的方案优化为例进行分析,得到了较好结果。为验证文中改进算法的有效性,选取多个不同规模的方案进行分析比较,结果显示本文提出的算法在优化结果及解的分布性等方面均更优。本文研究为我国海上岛屿救助基地选址和在资源有限的情况下如何科学配置救助船队提供了分析方法。     

基于VAR风险指标的投资组合模糊优化

在二目标有价证券选择基础上 ,引入目前流行的风险指标 VAR,以收益率与风险损失为目标 ,将模糊概念运用于有价证券组合选择 ,按投资者给定的期望目标及容差 ,讨论了 S型隶属函数模型 .通过 VAR的给定 ,将投资者所能承受的最大损失锁定 ,更好地反映出投资者对目标值的取值意图 .依据深圳股票市场9只股票收益率数据 ,采用进化规划进行优化计算 ,并验证模型的有效性 .     

Strategic defense and attack for series and parallel reliability systems

A system of independent components is defended by a strategic defender and attacked by a strategic attacker. The reliability of each component depends on how strongly it is defended and attacked, and on the intensity of the contest. In a series system, the attacker benefits from a substitution effect since attacker benefits flow from attacking any of the components, while the defender needs to defend all components. Even for a series system, when the attacker is sufficiently disadvantaged with high attack inefficiencies, and the intensity of the contest is sufficiently high, the defender earns maximum utility and the attacker earns zero utility. The results for the defender (attacker) in a parallel system are equivalent to the results for the attacker (defender) in a series system. Hence, the defender benefits from the substitution effect in parallel systems. With budget constraints the ratio of the investments for each component, and the contest success function for each component, are the same as without budget constraints when replacing the system values for the defender and attacker with their respective budget constraints.