高固含量无皂乳液聚合的研究─MMA/BA/EMA无皂乳液共聚合体系

本文将自行设计并合成的可共聚单体３－烯丙氧基－２－羟基－丙碳酸钠（ＡＨＰＳ）用于ＭＭＡ／ＢＡ／ＥＭＡ无皂乳液共聚体系，成功的制得了因含量高达６０％的稳定的无皂乳液．对其乳胶粒的形态结构、乳液成膜后共聚物动态力学行为、拉伸性能、耐水性及粘接强度进行了研究，并对乳胶粒的成核机理进行了探讨。实验结果表明，与常规乳液聚合体系相比，所获得的无皂乳液的乳胶粒大小均一，粒径在０．５μｍ左右，粘度低，储存稳定；共聚物至完全无规立构，玻璃化转变温度均在２５℃附近，拉伸强度明显增大，耐水性和剥离强度显著提高。     

含氢聚甲基硅氧烷/丙烯酸丁酯/羟甲基丙烯酰胺复合乳液的研究——原料配比对乳液及胶膜性能的影响

采用含氢聚甲基硅氧烷（ＰＨＭＳ）与丙烯酸酯类单体进行接枝共聚，制得兼具二者优异性能的新型ＰＨＭＳ／丙烯酸丁酯（ＢＡ）／羟甲基丙烯酰胺（ＮＭＡ）复合聚合物乳液．讨论了ＰＨＭＳ、ＮＭＡ和引发剂用量对该复合乳液的聚合反应转化率、稳定性及粘度的影响．采用透射电子显微镜和粒度测试仪对不同反应条件下制备的乳液的粒度进行了测定．同时对聚合反应的机理、产物的结构及胶膜性能作了考察．结果表明：通过乳液聚合，得到了ＰＨＭＳ／ＢＡ／ＮＭＡ共聚物，控制ＰＨＭＳ、ＮＭＡ、引发剂等用量可制得粒度和粘度适中，具有较高转化率的稳定ＰＨＭＳ／ＢＡ／ＮＭＡ复合聚合物乳液，该乳液所制得的胶膜具有优良的性能     

胺基铪茂催化乙烯/1-辛烯无规共聚合的研究

在亚乙基双（ 茚基） 二胺化茂铪（ｒａｃ Ｃ２Ｈ４（Ｉｎｄ）２Ｈｆ（ＮＭｅ２）２ ,简称１ ,Ｉｎｄ ＝ 茚基,Ｍｅ＝ 甲基） 催化作用下,对乙烯（Ｅ） 与１ 辛烯（Ｏ） 无规共聚合进行了研究．作为比较,利用异亚丙基（ 环戊二烯基）（１ 芴基） 二甲基锆茂催化体系（（ＣＨ３）２Ｃ（Ｆｌｕｏ）（Ｃｐ）ＺｒＭｅ２ ,简称２ ,Ｆｌｕｏ ＝ 芴基,Ｃｐ ＝ 环戊二烯基） 对乙烯／１ 辛烯在相同共聚合条件下进行了共聚合．结果表明,在单体浓度比［Ｏ］／［Ｅ］ 较小时共聚合速率随单体浓度比增加而增加,进一步增加单体浓度比则导致共聚合速率降低．催化体系１／Ａｌ（ｉＢｕ）２Ｈ／［Ｐｈ３Ｃ］［Ｂ（Ｃ６Ｆ５）４］（３） 催化共聚活性比２／ ＭＡＯ高得多．共聚物中辛烯含量随反应单体１ 辛烯含量的增加而增加,两单体竞聚率乘积（ ｒＥ×ｒｏ） 小于１ ,表明聚合物为无规共聚物．相同共聚单体浓度比下１／Ａｌ（ｉＢｕ）２Ｈ／３ 催化共聚物中辛烯含量比２／ ＭＡＯ 共聚物中辛烯含量高,表明前者具有更强的共聚合能力．所得无规共聚物熔点温度、结晶度、本体粘度及密度随共聚物中辛烯含量的增加而显著降低．辛烯含量较高时共聚物呈现明显无结晶行为．差示扫描量热分析显示,同乙烯均聚?     

MMA／BA／AA／HEMA无皂乳液体系的合成与性能表征

本文采用分步控浊结合种子人聚的新方法合成了ＭＭＡ／ＢＡ／ＡＡ／ＨＥＭＡ无皂乳液体系,并对其粒径、耐水性以及贮存稳定性进行了研究。实验结果表明,该方法合成的无皂体系不仅固含量较高,反应稳定性和贮存稳定性较好,而且具有优良的耐水性。     

离子型共聚单体用于高固含量无皂乳液聚合的研究：甲基丙烯酸异丁 …

该文采用自行合成的一种带亲水性磺酸离子基团及羟基的可共聚单体３－烯丙氧基－２－羟基丙磺酸钠（ＡＨＰＳ）用于甲基丙烯酸异丁酯／甲基丙烯酸甲酯／丙烯酸丁酯（ＩＢＭＡ／ＭＭＡ／ＢＡ）无皂乳液聚合体系。对乳胶粒粒径大小、乳液流体力学行为、共聚物的动态力学性质、拉伸行为及耐水性进行了研究,并对乳胶粒的成核机理进行了探讨。实验结果表明,带亲水性离子基团可共聚单体ＡＨＰＳ的加入可获得０．６μｍ左右的乳胶粒,乳液     

含氢聚甲基硅氧烷/丙烯酸丁酯/羟甲基丙烯酰胺复合乳液的制备方法对乳液性质的影响

采用自由基引发剂用３种不同的聚合方法制备了新型的含氢聚甲基硅氧烷（ＰＨＭＳ）／丙烯酸丁酯（ＢＡ）／羟甲基丙烯酰胺（ＮＭＡ）复合聚合物乳液。详细讨论了不同聚合方法对乳液稳定性和乳胶粒子的影响，同时对聚合反应的机理、产物的结构作了考察．结果表明：通过乳液聚合，得到了ＰＨＭＳ／ＢＡ／ＮＭＡ共聚物；单体乳液滴加法所得乳液粒径较小，乳液性能稳定，是制备ＰＨＭＳ／ＢＡ／ＮＭＡ复合聚合物乳液较适宜的方法．     

异戊二烯/甲基丙烯酸甲酯嵌段共聚物的合成与微结构研究

用稀土催化剂ＲＥ（Ｐ２０４）３ （ｉ Ｂｕ）３Ａｌ ＢｒＣＨ２ＣＨ２Ｂｒ（ＲＥ＝Ｎｄ,Ｐｒ,Ｙ等）合成嵌段共聚物Ｐ（ＩＰ ｂ ＭＭＡ）．系统考察了共聚合反应特征,以ＤＳＣ,１Ｈ ＮＭＲ,１３Ｃ ＮＭＲ技术研究了该嵌段共聚物的微结构．发现以二溴乙烷为添加剂的稀土催化体系是制备Ｐ（ＩＰ ｂ ＭＭＡ）的良好催化剂,共聚物含２个玻璃化转变温度,分别为－７５６℃和１２９℃,嵌段共聚物的结构规整,（ＩＰ）ｍ段以ｃｉｓ １,４结构为主,其含量为９７％左右,３,４ 结构为３％左右,链节间以头 尾方式连接．（ＭＭＡ）ｎ段以间同立构为主,其含量达７４％．     

离子型表面活性单体存在下的MMA／BA乳液聚合（I）：表面？…

合成了两种离子型表面活性单体（Ｓｕｒｆｍｅｒ）－磺化－十二醇－烯丙基甘油－丁二酸酯钠盐（ＺＣ－Ｌ）和磺化－十二醇－甲基丙烯酰甘油－丁二酸酯钠盐（ＺＤ－Ｌ）。着重研究了ＺＣ－Ｌ的结构、表面张力行为、均聚及共聚能力。实验结果表明,不同Ｓｕｒｆｍｅｒ用量以及不同固含量下,ＭＭＡ／ＢＡ／Ｓｕｒｆｍｅｒ、ＭＭＡ／Ｓｕｒｆｍｅｒ及ＢＡ／Ｓｕｒｆｍｅｒ共聚乳液的表面张力较高,说明Ｓｕｒｆｍｅｒ已通过共聚结合在乳     

单体极性对甲基丙烯酸甲酯/丙烯酸丁酯/甲基丙烯酸钠无皂乳液共聚合的影响

研究了少量甲基丙烯酸钠（ＮａＭＡ）存在下单体极性对甲基丙烯酸甲酯（ＭＭＡ）／丙烯酸丁酯（ＢＡ）无皂乳液共聚合的影响．单体极性降低，使粒径减小、聚合速率提高、乳液表面张力和粘度降低、粒子表面电荷密度增大、聚合物分子量提高．ＭＭＡ／ＮａＭＡ无皂乳液聚合物只呈现一个玻璃化温度Ｔｇ，ＢＡ／ＮａＭＡ无皂乳液聚合物呈现两个Ｔｇ，ＭＭＡ／ＢＡ比为２∶１～１∶２的ＭＭＡ／ＢＡ／ＮａＭＡ无皂乳液聚合物呈现四个Ｔｇ，这是由于粒子外面相对富含ＯＳＯ－３和ＣＯＯ－基聚合物的亚层溶解了较多的水，使ＢＡ向粒子中心扩散，ＭＭＡ向外扩散，造成组成差异和相分离而引起的．     

甲基丙烯酸二甲氨基乙酯溴代烷季铵盐与苯乙烯共聚合的研究

以甲基丙烯酸二甲氨基乙酯溴代乙烷（ Ｍ Ａ Ｅ Ｂ） 或丁烷（ Ｍ Ａ Ｂ Ｂ） 季胺盐与苯乙烯（ Ｓｔ）为单体,采用溶液自由基共聚合方法,合成了一类新型阳离子两亲共聚物．详细地研究了聚合条件及共聚物的溶解性．共聚物“亲油”和“亲水”单元的无规结构被 Ｉ Ｒ、１ Ｈ Ｎ Ｍ Ｒ 及１３ Ｃ Ｎ Ｍ Ｒ所证实．最后,用线性化（ Ｙ Ｂ Ｒ） 法分别求得 Ｍ Ａ Ｅ Ｂ／ Ｓｔ 和 Ｍ Ａ Ｂ Ｂ／ Ｓｔ 的单体竞聚率,ｒ Ｍ Ａ Ｂ Ｂ ＝０４４ ,ｒ Ｓｔ ＝ ０１５ ,ｒ Ｍ Ａ Ｅ Ｂ＝ ０６６ ,ｒ Ｓｔ＝ ０３６ ．     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.